DATASHEET
HI-506, HI-507, HI-508, HI-509
Single 16 and 8/Differential 8-Channel and 4-Channel CMOS Analog Multiplexers
The HI-506/HI-507 and HI-508/HI-509 monolithic CMOS
multiplexers each include an array of sixteen and eight
analog switches respectively, a digital decoder circuit for
channel selection, voltage reference for logic thresholds, and
an enable input for device selection when several
multiplexers are present. The Dielectric Isolation (DI)
process used in fabrication of these devices eliminates the
problem of latchup. DI also offers much lower substrate
leakage and parasitic capacitance than conventional junction
isolated CMOS (see Application Note AN520).
Features
The switching threshold for each digital input is established by
an internal +5V reference, providing a guaranteed minimum
2.4V for logic “1” and maximum 0.8V for logic “0”. This allows
direct interface without pullup resistors to signals from most
logic families: CMOS, TTL, DTL and some PMOS. For
protection against transient overvoltage, the digital inputs
include a series 200 resistor and diode clamp to each
supply.
• Break-Before-Make Switching
The HI-506 is a single 16-channel, the HI-507 is an
8-channel differential, the HI-508 is a single 8-channel and
the HI-509 is a 4-channel differential multiplexer.
• Precision Instrumentation
If input overvoltages are present, the HI-546/HI-547/HI-548/
HI-549 multiplexers are recommended.
FN3142 Rev 10.00
Jun 14, 2016
FN3142
Rev 10.00
Jun 14, 2016
• Pb-Free Available (RoHS Compliant) (See Ordering Info)
• Low ON Resistance . . . . . . . . . . . . . . . . . . . . . . . . 180
• Wide Analog Signal Range ±15V
• TTL/CMOS Compatible
• Access Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250ns
• Maximum Power Supply . . . . . . . . . . . . . . . . . . . . . . 44V
• No Latch-Up
• Replaces DG506A/DG506AA and DG507A/DG507AA
• Replaces DG508A/DG508AA and DG509A/DG509AA
Applications
• Data Acquisition Systems
• Demultiplexing
• Selector Switch
Page 1 of 25
HI-506, HI-507, HI-508, HI-509
Ordering Information
PART NUMBER
PART MARKING
HI1-0506-2
HI1-506-2
HI4P0506-5Z (Note 1)
HI4P 506-5Z
HI9P0506-9Z (Note 1)
TEMP.
RANGE (°C)
-55 to +125
PACKAGE
PKG. DWG. #
28 Ld CERDIP
F28.6
0 to +75
28 Ld PLCC (Pb-free)
N28.45
HI9P506-9Z
-40 to +85
28 Ld SOIC (Pb-free)
M28.3
HI3-0507-5Z (No longer
available, recommended
replacement: HI3-0547-5Z)
HI3-507-5Z
0 to +75
HI1-0508-2
HI1-508-2
HI3-0508-5Z (Note 1)
HI3-508-5Z
0 to +75
16 Ld PDIP (Note 3) (Pb-free) E16.3
HI9P0508-5Z (Notes 1, 2)
HI9P508-5Z
0 to +75
16 Ld SOIC (Pb-free)
M16.15
HI9P0508-9Z (Note 1)
HI9P508-9Z
-40 to +85
16 Ld SOIC (Pb-free)
M16.15
HI1-0509-2
HI1-509-2
-55 to +125
16 Ld CERDIP
F16.3
HI4P0509-5Z (Notes 1, 2) (No
longer available,
recommended replacement:
DG409DYZ)
HI4P 509-5Z
20 Ld PLCC (Pb-free)
N20.35
-55 to 125
0 to +75
28 Ld PDIP (Note 3) (Pb-free) E28.6
16 Ld CERDIP
F16.3
NOTES:
1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte
tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC
J STD-020.
2. Add “96” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
3. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
FN3142 Rev 10.00
Jun 14, 2016
Page 2 of 25
HI-506, HI-507, HI-508, HI-509
Pinouts
+VSUPPLY
OUT
-VSUPPLY
IN 8
28 OUT
NC
1
NC
+VSUPPLY
HI-506 (PLCC)
TOP VIEW
IN 16
HI-506 (CERDIP, SOIC)
TOP VIEW
4
3
2
1
28
27
26
NC 2
27 -VSUPPLY
NC 3
26 IN 8
IN 16 4
25 IN 7
IN 15
5
25
IN 7
IN 15 5
24 IN 6
IN 14
6
24
IN 6
IN 14 6
23 IN 5
IN 13 7
22 IN 4
IN 13
7
23
IN 5
IN 12 8
21 IN 3
IN 12
8
22
IN 4
IN 11
9
20 IN 2
IN 11
9
21
IN 3
IN 10 10
19 IN 1
IN 10
10
20
IN 2
IN 9
11
19
IN 1
HI-507 (PDIP, CERDIP)
TOP VIEW
+VSUPPLY
1
OUT B 2
28 OUT A
27 -VSUPPLY
NC 3
26 IN 8A
IN 8B 4
25 IN 7A
IN 7B 5
24 IN 6A
IN 6B 6
23 IN 5A
IN 5B 7
22 IN 4A
IN 4B 8
21 IN 3A
IN 3B 9
20 IN 2A
IN 2B 10
19 IN 1A
IN 1B 11
18 ENABLE
GND 12
17 ADDRESS A0
NC 13
16 ADDRESS A1
NC 14
15 ADDRESS A2
FN3142 Rev 10.00
Jun 14, 2016
16
17
18
ENABLE
15 ADDRESS A2
15
A0
ADDRESS A3 14
14
A1
16 ADDRESS A1
13
A2
NC 13
12
A3
17 ADDRESS A0
NC
GND 12
18 ENABLE
GND
IN 9 11
HI-508 (PDIP, CERDIP, SOIC)
TOP VIEW
A0 1
16 A1
ENABLE 2
15 A2
-VSUPPLY
3
14 GND
IN 1 4
13 +VSUPPLY
IN 2 5
12 IN 5
IN 3 6
11 IN 6
IN 4 7
10 IN 7
OUT 8
9 IN 8
Page 3 of 25
HI-506, HI-507, HI-508, HI-509
Pinouts
(Continued)
15 GND
A0
NC
A1
GND
14 +VSUPPLY
3
2
1
20
19
IN 3A 6
11 IN 3B
IN 4A 7
10 IN 4B
OUT A 8
FN3142 Rev 10.00
Jun 14, 2016
9 OUT B
-VSUPPLY
4
18 +VSUPPLY
IN 1A
5
17 IN 1B
NC
6
16 NC
IN 2A
7
15 IN 2B
IN 3A
8
14 IN 3B
9
10
11
12
13
IN 4B
12 IN 2B
OUT B
13 IN 1B
IN 2A 5
NC
IN 1A 4
OUT A
ENABLE 2
-VSUPPLY 3
16 A1
IN 4A
A0 1
HI-509 (PLCC)
TOP VIEW
ENABLE
HI-509 (PDIP, CERDIP, SOIC)
TOP VIEW
Page 4 of 25
HI-506, HI-507, HI-508, HI-509
Truth Tables
HI-508
HI-506
A3
A2
A1
A0
EN
“ON” CHANNEL
A2
A1
A0
EN
“ON” CHANNEL
X
X
X
X
L
None
X
X
X
L
None
L
L
L
L
H
1
L
L
L
H
1
L
L
L
H
H
2
L
L
H
H
2
L
L
H
L
H
3
L
H
L
H
3
L
L
H
H
H
4
L
H
H
H
4
L
H
L
L
H
5
H
L
L
H
5
L
H
L
H
H
6
H
L
H
H
6
L
H
H
L
H
7
H
H
L
H
7
L
H
H
H
H
8
H
H
H
H
8
H
L
L
L
H
9
H
L
L
H
H
10
H
L
H
L
H
11
A1
A0
EN
“ON” CHANNEL PAIR
H
L
H
H
H
12
X
X
L
None
H
H
L
L
H
13
L
L
H
1
H
H
L
H
H
14
L
H
H
2
H
H
H
L
H
15
H
L
H
3
H
H
H
H
H
16
H
H
H
4
HI-509
HI-507
A2
A1
A0
EN
“ON” CHANNEL
X
X
X
L
None
L
L
L
H
1
L
L
H
H
2
L
H
L
H
3
L
H
H
H
4
H
L
L
H
5
H
L
H
H
6
H
H
L
H
7
H
H
H
H
8
FN3142 Rev 10.00
Jun 14, 2016
Page 5 of 25
HI-506, HI-507, HI-508, HI-509
Functional Diagrams
HI-506
HI-507
IN 1
OUT
IN 2
IN 1A
OUT A
IN 8A
DECODER/
DRIVER
IN 1B
OUT B
IN 16
DECODER/
DRIVER
5V
REF
IN 8B
LEVEL
SHIFT
† DIGITAL
INPUT
PROTECTION
† † † †
†
A0 A1 A2 A3
EN
5V
REF
LEVEL
SHIFT
† DIGITAL
INPUT
PROTECTION
HI-508
†
†
†
†
A0
A1
A2
EN
HI-509
IN 1
OUT
IN 2
IN 1A
OUT A
IN 4A
DECODER/
DRIVER
IN 1B
OUT B
IN 8
5V
REF
† DIGITAL
INPUT
PROTECTION
DECODER/
DRIVER
IN 4B
LEVEL
SHIFT
†
†
†
†
A0
A1
A2
EN
5V
REF
† DIGITAL
FN3142 Rev 10.00
Jun 14, 2016
INPUT
PROTECTION
LEVEL
SHIFT
†
†
†
A0
A1
EN
Page 6 of 25
HI-506, HI-507, HI-508, HI-509
Schematic Diagrams
ADDRESS DECODER
V+
P
P
P
P
A0 OR A0
A1 OR A1
P
P
P
N
N
N
N
N
A2 OR A2
TO P-CHANNEL
DEVICE OF
THE SWITCH
TO N-CHANNEL
DEVICE OF
THE SWITCH
N
A3 OR A3
N
ENABLE
DELETE A3 OR A3 INPUT FOR HI-507, HI-508, HI-509
DELETE A2 OR A2 INPUT FOR HI-509
V-
ADDRESS INPUT BUFFER LEVEL SHIFTER
V+
P3
P1
P5
A
V+
D1
P4
N1
VL
VR
D2
P2
P7
P8
P9
P10
N6
N7
N8
N9
N10
N4
200
A
N5
N2
V-
P6
N3
AIN
ALL N-CHANNEL BODIES TO VALL P-CHANNEL BODIES TO V+
UNLESS OTHERWISE INDICATED
V-
TTL REFERENCE CIRCUIT
MULTIPLEX SWITCH
V+
P15
Q1P
Q2P Q3P
N18
FROM DECODE
Q4P
Q5N
V+
Q6N
VL
Q8N
R2
16.8k
N12
Q7P
Q11P
VVR
R3
6.8k
Q9P
N13
N14
OUT
P17
D3
Q10N
N17
N19
IN
N15
P18
P16
Q12N
FROM DECODE
V-
FN3142 Rev 10.00
Jun 14, 2016
GND
Page 7 of 25
HI-506, HI-507, HI-508, HI-509
Absolute Maximum Ratings
Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+44V
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+22V
V- to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V
Digital Input Voltage (VEN , VA) . . . . . (V-) -4V to (V+) +4V or 20mA,
Whichever Occurs First
Analog Signal (VIN, VOUT, Note 5) . . . . . . . . . . (V-) -2V to (V+) +2V
Continuous Current, In or Out . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current, In or Out (Pulsed 1ms, 10% Duty Cycle Max) . 40mA
Thermal Resistance (Typical, Note 4)
Operating Conditions
Temperature Ranges
HI-50X-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
HI-50X-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-25°C to +85°C
HI-50X-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +75°C
HI-50X-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Typical Minimum Supply Voltage . . . . . . . . . . . . 10V or Single 20V
JA (°C/W)
JC (°C/W)
16 Ld CERDIP Package. . . . . . . . . . . .
85
32
16 Ld SOIC Package . . . . . . . . . . . . . .
115
N/A
16 Ld PDIP Package . . . . . . . . . . . . . .
100
N/A
20 Ld PLCC Package. . . . . . . . . . . . . .
80
N/A
28 Ld CERDIP Package. . . . . . . . . . . .
55
18
28 Ld PDIP Package . . . . . . . . . . . . . .
60
N/A
28 Ld SOIC Package . . . . . . . . . . . . . .
70
N/A
28 Ld PLCC Package. . . . . . . . . . . . . .
70
N/A
Maximum Junction Temperature
Ceramic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175°C
Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
4. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
5. Signals on IN or OUT exceeding V+ or V- are clamped by internal diodes. Limit resulting current to maximum current ratings. If an overvoltage
condition is anticipated (analog input exceeds either power supply voltage), the Intersil HI-546/HI-547/HI-548/HI-549 multiplexers are
recommended.
Electrical Specifications
Supplies = +15V, -15V; VAH (Logic Level High) = 2.4V; VAL (Logic Level Low) = 0.8V,
Unless Otherwise Specified. For Test Conditions, Consult Test Circuits Section
-2
PARAMETER
TEST
CONDITIONS
TEMP
(°C)
MIN
(Note 11)
TYP
-4, -5, -9
MAX
MIN
(Note 11)
TYP
MAX
UNITS
DYNAMIC CHARACTERISTICS
Access Time, tA
Break-Before-Make Delay, tOPEN
Enable Delay (ON), tON(EN)
Enable Delay (OFF), tOFF(EN)
25
-
250
500
-
250
-
ns
Full
-
-
1000
-
-
1000
ns
25
25
80
-
25
80
-
ns
25
-
250
500
-
250
-
ns
Full
-
-
1000
-
-
1000
ns
25
-
250
500
-
250
-
ns
Full
-
-
1000
-
-
1000
ns
To 0.1%
25
-
1.2
-
-
1.2
-
s
To 0.01%
25
-
2.4
-
-
2.4
-
s
Settling Time, tS
(HI-508 and HI-509)
To 0.1%
25
-
360
-
-
360
-
ns
To 0.01%
25
-
600
-
-
600
-
ns
Off Isolation
Note 9
Settling Time, tS
(HI-506 and HI-507)
25
-
68
-
-
68
-
dB
Channel Input Capacitance, CS(OFF)
25
-
10
-
-
10
-
pF
Channel Output Capacitance, CD(OFF)
HI-506
25
-
52
-
-
52
-
pF
HI-507
25
-
30
-
-
30
-
pF
HI-508
25
-
17
-
-
17
-
pF
HI-509
25
-
12
-
-
12
-
pF
Digital Input Capacitance, CA
25
-
6
-
-
6
-
pF
Input to Output Capacitance, CDS(OFF)
25
-
0.08
-
-
0.08
-
pF
DIGITAL INPUT CHARACTERISTICS
Input Low Threshold, VAL
Full
-
-
0.8
-
-
0.8
V
Input High Threshold, VAH
Full
2.4
-
-
2.4
-
-
V
FN3142 Rev 10.00
Jun 14, 2016
Page 8 of 25
HI-506, HI-507, HI-508, HI-509
Electrical Specifications
Supplies = +15V, -15V; VAH (Logic Level High) = 2.4V; VAL (Logic Level Low) = 0.8V,
Unless Otherwise Specified. For Test Conditions, Consult Test Circuits Section (Continued)
-2
PARAMETER
Input Leakage Current
(High or Low), IA
TEST
CONDITIONS
Note 8
TEMP
(°C)
MIN
(Note 11)
TYP
Full
-
-
Full
-15
25
-
25
-
5
-4, -5, -9
MAX
MIN
(Note 11)
TYP
MAX
UNITS
1.0
-
-
1.0
A
-
+15
-15
-
+15
V
180
300
-
180
400
-
-
5
-
%
nA
ANALOG CHANNEL CHARACTERISTICS
Analog Signal Range, VIN
On Resistance, rON
Note 6
rON , (Any Two Channels)
Off Input Leakage Current, IS(OFF)
Off Output Leakage Current,
ID(OFF)
HI-506
Note 7
Note 7
25
-
0.03
-
-
0.03
-
Full
-
-
50
-
-
50
nA
25
-
0.3
-
-
0.3
-
nA
Full
-
-
300
-
-
300
nA
HI-507
Full
-
-
200
-
-
200
nA
HI-508
Full
-
-
200
-
-
200
nA
HI-509
Full
-
-
100
-
-
100
nA
25
-
0.3
-
-
0.3
-
nA
HI-506
Full
-
-
300
-
-
300
nA
HI-507
Full
-
-
200
-
-
200
nA
HI-508
Full
-
-
200
-
-
200
nA
HI-509
Full
-
-
100
-
-
100
nA
Full
-
-
50
-
-
50
nA
On Channel Leakage Current, ID(ON)
Note 7
Differential Off Output Leakage Current, IDIFF
(HI-507, HI-509 Only)
POWER SUPPLY CHARACTERISTICS
Current, I+
HI-506/HI-507
Note 10
Full
-
1.5
3.0
-
1.5
3.0
mA
HI-508/HI-509
Note 10
Full
-
1.5
2.4
-
1.5
2.4
mA
Current, IHI-506/HI-507
Note 10
Full
-
0.4
1.0
-
0.4
1.0
mA
HI-508/HI-509
Note 10
Full
-
0.4
1.0
-
0.4
1.0
mA
Power Dissipation, PD
HI-506/HI-507
Full
-
-
60
-
-
60
mW
HI-508/HI-509
Full
-
-
51
-
-
51
mW
NOTES:
6. VOUT = ±10V, IOUT = +1mA.
7. 10nA is the practical lower limit for high speed measurement in the production test environment.
8. Digital input leakage is primarily due to the clamp diodes (see Schematic). Typical leakage is less than 1nA at +25°C.
9. VEN = 0.8V, RL = 1k, CL = 15pF, VS = 7VRMS , f = 100kHz.
10. VEN , VA = 0V or 2.4V.
11. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
FN3142 Rev 10.00
Jun 14, 2016
Page 9 of 25
HI-506, HI-507, HI-508, HI-509
Test Circuits and Waveforms
TA = +25°C, VSUPPLY = ±15V, VAH = 2.4V, VAL = 0.8V, Unless Otherwise Specified
1mA
V2
IN
OUT
VIN
rON =
V2
1mA
FIGURE 1A. TEST CIRCUIT
2.2
NORMALIZED RESISTANCE
(REFERRED TO VALUE AT15V)
ON RESISTANCE ()
400
300
+125°C
200
+25°C
100
-55°C
0
-15
-10
-5
0
5
ANALOG INPUT (V)
10
15
-55°C TO +125°C
VIN = 0V
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
10
11
12
13
14
15
SUPPLY VOLTAGE (V)
FIGURE 1B. ON RESISTANCE vs ANALOG INPUT VOLTAGE
FIGURE 1C. NORMALIZED ON RESISTANCE vs SUPPLY
VOLTAGE
FIGURE 1. ON RESISTANCE
100nA
OFF OUTPUT
LEAKAGE CURRENT
ID(OFF)
LEAKAGE CURRENT
10nA
0.8V
EN
ID(ON)
OUT
1nA
A
100pA
10pA
10V
OFF INPUT
LEAKAGE CURRENT
IS(OFF)
25
50
75
100
ID(OFF)
10V
125
TEMPERATURE (°C)
FIGURE 2A. LEAKAGE CURRENT vs TEMPERATURE
FN3142 Rev 10.00
Jun 14, 2016
FIGURE 2B. ID(OFF) TEST CIRCUIT (NOTE 12)
Page 10 of 25
HI-506, HI-507, HI-508, HI-509
Test Circuits and Waveforms
TA = +25°C, VSUPPLY = ±15V, VAH = 2.4V, VAL = 0.8V, Unless Otherwise Specified (Continued)
OUT
OUT
IS(OFF)
A
A
0.8V
EN
10V
A0
10V
+10V
+10V
ID(ON)
EN
A1
2.4V
FIGURE 2C. IS(OFF) TEST CIRCUIT (NOTE 12)
FIGURE 2D. ID(ON) TEST CIRCUIT (NOTE 12)
FIGURE 2. LEAKAGE CURRENTS
NOTE:
12. Two measurements per channel: ±10V and +10V. (Two measurements per device for ID(OFF) ±10V and +10V)
70
SWITCH CURRENT (mA)
60
-55°C
50
+25°C
40
30
+125°C
20
A
VIN
10
0
0
2
4
6
8
10
12
VOLTAGE ACROSS SWITCH (V)
14
16
FIGURE 3A. ON CHANNEL CURRENT vs VOLTAGE
FIGURE 3B. TEST CIRCUIT
FIGURE 3. ON CHANNEL CURRENT
+15V/+10V
8
A
+ISUPPLY
SUPPLY CURRENT (mA)
VSUPPLY = 15V
V+
IN 1
6
A3
A2
4
VA
2
3.5V
VSUPPLY = 10V
0
50
1k
10k
100k
TOGGLE FREQUENCY (Hz)
1M
VA
10M
A1
IN 2
THRU
IN 7/15
A0
IN 8/16
EN
HIGH = 3.5V
LOW = 0V
50% DUTY CYCLE
† Similar connection for HI-507/
HI-508/HI-509
FIGURE 4A. SUPPLY CURRENT vs TOGGLE FREQUENCY
10V/5V
HI-506 †
GND
+10V/+5V
OUT
V-
A
10
M
14
pF
-ISUPPLY
-15V/-10V
FIGURE 4B. TEST CIRCUIT
FIGURE 4. DYNAMIC SUPPLY CURRENT
FN3142 Rev 10.00
Jun 14, 2016
Page 11 of 25
HI-506, HI-507, HI-508, HI-509
Test Circuits and Waveforms
TA = +25°C, VSUPPLY = ±15V, VAH = 2.4V, VAL = 0.8V, Unless Otherwise Specified (Continued)
+15V
V+
IN 1
600
ACCESS TIME (ns)
A3
IN 2 THRU
IN 7/15
A2
50
VA
400
A1
HI-506 †
A0
0
EN
3.5V
200
10V
+10V
IN 16
GND
OUT
V-
10
k
50
pF
-15V
2
3
4
5
13
LOGIC LEVEL (HIGH) (V)
14
† Similar connection for HI-507/
15
HI-508/HI-509
FIGURE 5A. ACCESS TIME vs LOGIC LEVEL (HIGH)
3.5V
FIGURE 5B. TEST CIRCUIT
ADDRESS
DRIVE (VA)
VA INPUT
2V/DIV.
50%
0V
S1 ON
+10V
OUTPUT
10%
OUTPUT
5V/DIV.
-10V
tA
S16 ON
200ns/DIV.
FIGURE 5D. WAVEFORMS
FIGURE 5C. MEASUREMENT POINTS
FIGURE 5. ACCESS TIME
+15V
A3
A2
VA
50
A1
V+
HI-506 †
+5V
IN 1
IN 2 THRU
IN 7/IN 15
IN 8 /16
A0
3.5V
VOUT
EN
GND
OUT
V-
200
50pF
-15V
† Similar connection for HI-507/HI-508/HI-509
FIGURE 6A. TEST CIRCUIT
FN3142 Rev 10.00
Jun 14, 2016
Page 12 of 25
HI-506, HI-507, HI-508, HI-509
Test Circuits and Waveforms
TA = +25°C, VSUPPLY = ±15V, VAH = 2.4V, VAL = 0.8V, Unless Otherwise Specified (Continued)
3.5V
VA INPUT
2V/DIV.
S1 ON
ADDRESS
DRIVE (VA)
0V
S16 ON
OUTPUT
1V/DIV.
OUTPUT
50%
50%
tOPEN
100ns/DIV.
FIGURE 6B. MEASUREMENT POINTS
FIGURE 6C. WAVEFORMS
FIGURE 6. BREAK-BEFORE-MAKE DELAY
+15V
A3
A2
A1
V+
HI-506 †
IN 1
+10V
IN 2 THRU
IN 7/IN 15
IN 8 /16
A0
VOUT
EN
VA
50
GND
OUT
V-
50pF
200
-15V
† Similar connection for HI-507/HI-508/HI-509
FIGURE 7A. TEST CIRCUIT
ENABLE
DRIVE
2V/DIV.
3.5V
50% ENABLE DRIVE (VA)
50%
0V
OUTPUT
90%
10%
DISABLED
0V
ENABLED
(S1 ON)
OUTPUT
2V/DIV.
tON(EN)
tOFF(EN)
100ns/DIV
FIGURE 7B. MEASUREMENT POINTS
FIGURE 7C. WAVEFORMS
FIGURE 7. ENABLE DELAYS
FN3142 Rev 10.00
Jun 14, 2016
Page 13 of 25
HI-506, HI-507, HI-508, HI-509
Typical Performance Curves
TA = 25°C, VSUPPLY = 15V, VAH = 2.4V, VAL = 0.8V, Unless Otherwise Specified
100
(VS), (VD) OFF ISOLATION (dB)
INPUT LOGIC THRESHOLD (V)
4
3
2
1
0
10
12
14
16
18
80
RL = 1k
60
RL = 10M
40
VEN = 0V
CLOAD = 28pF
VS = 7VRMS
20
0
104
20
105
POWER SUPPLY VOLTAGE (V)
FIGURE 8. LOGIC THRESHOLD vs POWER SUPPLY VOLTAGE
3
POWER SUPPLY CURRENT (mA)
POWER SUPPLY CURRENT (mA)
107
FIGURE 9. OFF ISOLATION vs FREQUENCY
3
2
VEN = 2.4V
VEN = 0V
1
0
-55
106
FREQUENCY (Hz)
2
EN = 5V
1
EN = 0V
0
-35
-15
-5
25
45
65
85
105
125
-55
-35
-15
TEMPERATURE (°C)
FIGURE 10A. HI-506/HI-507
-5
25
45
65
85
105
TEMPERATURE (°C)
FIGURE 10B. HI-508/HI-509
FIGURE 10. POWER SUPPLY CURRENT vs TEMPERATURE
FN3142 Rev 10.00
Jun 14, 2016
Page 14 of 25
125
HI-506, HI-507, HI-508, HI-509
Die Characteristics
METALLIZATION:
WORST CASE CURRENT DENSITY:
1.4 x 105 A/cm2
Type: CuAl
Thickness: 16kÅ ±2kÅ
TRANSISTOR COUNT:
SUBSTRATE POTENTIAL (NOTE):
421
-VSUPPLY
PROCESS:
PASSIVATION:
CMOS-DI
Type: Nitride/Silox
Nitride Thickness: 3.5kÅ ±1kÅ
Silox Thickness: 12kÅ ±2kÅ
NOTE: The substrate appears resistive to the -VSUPPLY terminal, therefore it may be left floating (Insulating Die Mount) or it may be mounted on a
conductor at -VSUPPLY potential.
Metallization Mask Layout
HI-506
EN A0
A1
A2
HI-507
A3
GND
EN
A0
A1
A2 NC
GND
IN 1
IN 9
IN 1A
IN 1B
IN 2
IN 10
IN 2A
IN 2B
IN 3
IN 11
IN 3A
IN 3B
IN 4
IN 12
IN 4A
IN 4B
IN 5
IN 13
IN 5A
IN 5B
IN 6
IN 14
IN 6A
IN 6B
IN 7
IN 15
IN 7A
IN 7B
IN 8
IN 16
IN 8A
IN 8B
-V OUT
FN3142 Rev 10.00
Jun 14, 2016
+V
NC
-V OUT A
+V OUT B
Page 15 of 25
HI-506, HI-507, HI-508, HI-509
Die Characteristics
METALLIZATION:
WORST CASE CURRENT DENSITY:
1.4 x 105 A/cm2
Type: CuAl
Thickness: 16kÅ 2kÅ
TRANSISTOR COUNT:
SUBSTRATE POTENTIAL (NOTE):
234
-VSUPPLY
PROCESS:
PASSIVATION:
CMOS-DI
Type: Nitride/Silox
Nitride Thickness: 3.5kÅ 1kÅ
Silox Thickness: 12kÅ 2kÅ
NOTE: The substrate appears resistive to the -VSUPPLY terminal, therefore it may be left floating (Insulating Die Mount) or it may be mounted on a
conductor at -VSUPPLY potential.
Metallization Mask Layout
HI-508
EN A0
A1
A2
HI-509
GND
EN A0
+VSUP
-VSUP
A1
GND
-VSUP
+VSUP
IN 1
IN 5
IN 1A
IN 1B
IN 2
IN 6
IN 2A
IN 2B
IN 3A
IN 3
IN 3B
IN 7
IN 4 OUT
FN3142 Rev 10.00
Jun 14, 2016
IN 8
IN 4A OUT A
OUT B IN 4B
Page 16 of 25
HI-506, HI-507, HI-508, HI-509
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that
you have the latest revision.
DATE
REVISION
CHANGE
May 24, 2016
FN3142.10
Updated ordering information table on page 2.
August 7, 2015
FN3142.9
Updated ordering information table on page 2.
Added Revision History and About Intersil sections.
Updated M28.3 to most recent revision with change as follows:
Added land pattern
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
FN3142 Rev 10.00
Jun 14, 2016
Page 17 of 25
HI-506, HI-507, HI-508, HI-509
Dual-In-Line Plastic Packages (PDIP)
N
E16.3 (JEDEC MS-001-BB ISSUE D)
E1
INDEX
AREA
1 2 3
16 LEAD DUAL-IN-LINE PLASTIC PACKAGE
N/2
INCHES
-B-
SYMBOL
-AE
D
BASE
PLANE
-C-
SEATING
PLANE
A2
A
L
D1
e
B1
D1
B
0.010 (0.25) M
C
L
eA
A1
eC
C A B S
C
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between English and
Metric dimensions, the inch dimensions control.
MILLIMETERS
MIN
MAX
MIN
MAX
NOTES
A
-
0.210
-
5.33
4
A1
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
B1
0.045
0.070
1.15
1.77
8, 10
C
0.008
0.014
0.204
0.355
-
D
0.735
0.775
18.66
19.68
5
D1
0.005
-
0.13
-
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
2.54 BSC
-
3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication No. 95.
eA
0.300 BSC
7.62 BSC
6
eB
-
0.430
-
10.92
7
4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3.
L
0.115
0.150
2.93
3.81
4
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
5. D, D1, and E1 dimensions do not include mold flash or protrusions.
Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
N
16
16
9
Rev. 0 12/93
7. eB and eC are measured at the lead tips with the leads unconstrained.
eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions. Dambar
protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,
E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).
FN3142 Rev 10.00
Jun 14, 2016
Page 18 of 25
HI-506, HI-507, HI-508, HI-509
Dual-In-Line Plastic Packages (PDIP)
E28.6 (JEDEC MS-011-AB ISSUE B)
N
28 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
SYMBOL
-B-
-C-
SEATING
PLANE
A2
e
B1
D1
B
0.010 (0.25) M
A1
eC
C A B S
MAX
NOTES
-
0.250
-
6.35
4
0.015
-
0.39
-
4
A2
0.125
0.195
3.18
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.030
0.070
0.77
1.77
8
eA
C
0.008
0.015
0.204
0.381
-
D
1.380
1.565
D1
0.005
-
A
L
D1
MIN
A
E
BASE
PLANE
MAX
A1
-AD
MILLIMETERS
MIN
C
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between English and
Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
35.1
39.7
5
-
5
0.13
E
0.600
0.625
15.24
15.87
6
E1
0.485
0.580
12.32
14.73
5
e
0.100 BSC
2.54 BSC
-
eA
0.600 BSC
15.24 BSC
6
3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication No. 95.
eB
-
0.700
-
17.78
7
L
0.115
0.200
2.93
5.08
4
4. Dimensions A, A1 and L are measured with the package seated in
JEDEC seating plane gauge GS-3.
N
5. D, D1, and E1 dimensions do not include mold flash or protrusions.
Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
28
28
9
Rev. 1 12/00
7. eB and eC are measured at the lead tips with the leads unconstrained.
eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions. Dambar
protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,
E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).
FN3142 Rev 10.00
Jun 14, 2016
Page 19 of 25
HI-506, HI-507, HI-508, HI-509
Ceramic Dual-In-Line Frit Seal Packages (CERDIP)
F16.3 MIL-STD-1835 GDIP1-T16 (D-2, CONFIGURATION A)
16 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE
LEAD FINISH
c1
-D-
-A-
BASE
METAL
(c)
E
M
-Bbbb S
C A-B S
Q
-C-
SEATING
PLANE
S1
b2
ccc M
C A-B S
D S
eA/2
NOTES
-
0.200
-
5.08
-
0.014
0.026
0.36
0.66
2
b1
0.014
0.023
0.36
0.58
3
b2
0.045
0.065
1.14
1.65
-
b3
0.023
0.045
0.58
1.14
4
c
0.008
0.018
0.20
0.46
2
c1
0.008
0.015
0.20
0.38
3
D
-
0.840
-
21.34
5
E
0.220
0.310
5.59
7.87
5
eA
e
b
MAX
b
A A
MIN
A
A
L
MILLIMETERS
MAX
M
(b)
D
BASE
PLANE
MIN
b1
SECTION A-A
D S
INCHES
SYMBOL
c
aaa M C A - B S D S
NOTES:
1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
e
0.100 BSC
2.54 BSC
-
eA
0.300 BSC
7.62 BSC
-
eA/2
0.150 BSC
3.81 BSC
-
L
0.125
0.200
3.18
5.08
-
Q
0.015
0.060
0.38
1.52
6
S1
0.005
-
0.13
-
7
105o
90o
105o
-
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
90o
aaa
-
0.015
-
0.38
-
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
bbb
-
0.030
-
0.76
-
ccc
-
0.010
-
0.25
-
M
-
0.0015
-
0.038
2, 3
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
5. This dimension allows for off-center lid, meniscus, and glass
overrun.
N
16
16
8
Rev. 0 4/94
6. Dimension Q shall be measured from the seating plane to the
base plane.
7. Measure dimension S1 at all four corners.
8. N is the maximum number of terminal positions.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
FN3142 Rev 10.00
Jun 14, 2016
Page 20 of 25
HI-506, HI-507, HI-508, HI-509
Ceramic Dual-In-Line Frit Seal Packages (CERDIP)
F28.6 MIL-STD-1835 GDIP1-T28 (D-10, CONFIGURATION A)
28 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE
LEAD FINISH
c1
-D-
-A-
BASE
METAL
(c)
E
M
-Bbbb S
C A-B S
Q
-C-
SEATING
PLANE
S1
b2
ccc M
C A-B S
D S
eA/2
NOTES
-
0.232
-
5.92
-
0.014
0.026
0.36
0.66
2
b1
0.014
0.023
0.36
0.58
3
b2
0.045
0.065
1.14
1.65
-
b3
0.023
0.045
0.58
1.14
4
c
0.008
0.018
0.20
0.46
2
c1
0.008
0.015
0.20
0.38
3
D
-
1.490
-
37.85
5
E
0.500
0.610
15.49
5
eA
e
b
MAX
b
A A
MIN
A
A
L
MILLIMETERS
MAX
M
(b)
D
BASE
PLANE
MIN
b1
SECTION A-A
D S
INCHES
SYMBOL
c
aaa M C A - B S D S
NOTES:
1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
e
12.70
0.100 BSC
2.54 BSC
-
eA
0.600 BSC
15.24 BSC
-
eA/2
0.300 BSC
7.62 BSC
-
L
0.125
0.200
3.18
5.08
-
Q
0.015
0.060
0.38
1.52
6
S1
0.005
-
0.13
-
7
105o
90o
105o
-
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
90o
aaa
-
0.015
-
0.38
-
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
bbb
-
0.030
-
0.76
-
ccc
-
0.010
-
0.25
-
M
-
0.0015
-
0.038
2, 3
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
5. This dimension allows for off-center lid, meniscus, and glass
overrun.
N
28
28
8
Rev. 0 4/94
6. Dimension Q shall be measured from the seating plane to the
base plane.
7. Measure dimension S1 at all four corners.
8. N is the maximum number of terminal positions.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
FN3142 Rev 10.00
Jun 14, 2016
Page 21 of 25
HI-506, HI-507, HI-508, HI-509
Small Outline Plastic Packages (SOIC)
M16.15 (JEDEC MS-012-AC ISSUE C)
N
INDEX
AREA
H
0.25(0.010) M
16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
B M
INCHES
E
-B-
1
2
3
L
SEATING PLANE
-A-
A
D
h x 45°
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
SYMBOL
MIN
MAX
MIN
MAX
NOTES
A
0.0532
0.0688
1.35
1.75
-
A1
0.0040
0.0098
0.10
0.25
-
B
0.013
0.020
0.33
0.51
9
C
0.0075
0.0098
0.19
0.25
-
D
0.3859
0.3937
9.80
10.00
3
E
0.1497
0.1574
3.80
4.00
4
e
B S
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
MILLIMETERS
0.050 BSC
1.27 BSC
-
H
0.2284
0.2440
5.80
6.20
-
h
0.0099
0.0196
0.25
0.50
5
L
0.016
0.050
0.40
1.27
6
N
16
0°
16
8°
0°
7
8°
Rev. 1 6/05
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above
the seating plane, shall not exceed a maximum value of 0.61mm
(0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions are
not necessarily exact.
FN3142 Rev 10.00
Jun 14, 2016
Page 22 of 25
HI-506, HI-507, HI-508, HI-509
Small Outline Plastic Packages (SOIC)
M28.3 (JEDEC MS-013-AE ISSUE C)
N
28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
SYMBOL
-B-
1
2
3
L
SEATING PLANE
-A-
A
D
h x 45o
a
e
A1
B
C
0.10(0.004)
0.25(0.010) M
C A M
B S
MAX
MILLIMETERS
MIN
MAX
NOTES
A
0.0926
0.1043
2.35
2.65
-
A1
0.0040
0.0118
0.10
0.30
-
B
0.013
0.0200
0.33
0.51
9
C
0.0091
0.0125
0.23
0.32
-
D
0.6969
0.7125
17.70
18.10
3
E
0.2914
0.2992
7.40
7.60
4
e
-C-
MIN
0.05 BSC
h
0.01
0.029
0.25
0.75
5
L
0.016
0.050
0.40
1.27
6
10.00
-
0.394
N
0.419
1.27 BSC
H
28
0o
10.65
-
28
8o
0o
7
8o
Rev. 1, 1/13
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
TYPICAL RECOMMENDED LAND PATTERN
(1.50mm)
4. Dimension “E” does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
(9.38mm)
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above
the seating plane, shall not exceed a maximum value of 0.61mm
(0.024 inch)
(1.27mm TYP)
FN3142 Rev 10.00
Jun 14, 2016
(0.51mm TYP)
10. Controlling dimension: MILLIMETER. Converted inch dimensions are
not necessarily exact.
Page 23 of 25
HI-506, HI-507, HI-508, HI-509
Plastic Leaded Chip Carrier Packages (PLCC)
0.042 (1.07)
0.048 (1.22)
PIN (1) IDENTIFIER
0.042 (1.07)
0.056 (1.42)
0.004 (0.10)
C
0.025 (0.64)
R
0.045 (1.14)
0.050 (1.27) TP
C
L
N20.35 (JEDEC MS-018AA ISSUE A)
20 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE
INCHES
SYMBOL
D2/E2
E1 E
C
L
D2/E2
VIEW “A”
0.020 (0.51)
MIN
A1
A
D1
D
SEATING
-C- PLANE
0.020 (0.51) MAX
3 PLCS
0.026 (0.66)
0.032 (0.81)
MAX
MILLIMETERS
MIN
MAX
NOTES
A
0.165
0.180
4.20
4.57
-
A1
0.090
0.120
2.29
3.04
-
D
0.385
0.395
9.78
10.03
-
D1
0.350
0.356
8.89
9.04
3
D2
0.141
0.169
3.59
4.29
4, 5
E
0.385
0.395
9.78
10.03
-
E1
0.350
0.356
8.89
9.04
3
E2
0.141
0.169
3.59
4.29
4, 5
N
20
20
6
Rev. 2 11/97
0.013 (0.33)
0.021 (0.53)
0.025 (0.64)
MIN
0.045 (1.14)
MIN
MIN
VIEW “A” TYP.
NOTES:
1. Controlling dimension: INCH. Converted millimeter dimensions are
not necessarily exact.
2. Dimensions and tolerancing per ANSI Y14.5M-1982.
3. Dimensions D1 and E1 do not include mold protrusions. Allowable
mold protrusion is 0.010 inch (0.25mm) per side. Dimensions D1
and E1 include mold mismatch and are measured at the extreme
material condition at the body parting line.
4. To be measured at seating plane -C- contact point.
5. Centerline to be determined where center leads exit plastic body.
6. “N” is the number of terminal positions.
FN3142 Rev 10.00
Jun 14, 2016
Page 24 of 25
HI-506, HI-507, HI-508, HI-509
Plastic Leaded Chip Carrier Packages (PLCC)
0.042 (1.07)
0.048 (1.22)
PIN (1) IDENTIFIER
0.042 (1.07)
0.056 (1.42)
0.004 (0.10)
C
0.025 (0.64)
R
0.045 (1.14)
0.050 (1.27) TP
C
L
N28.45 (JEDEC MS-018AB ISSUE A)
28 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE
INCHES
SYMBOL
D2/E2
C
L
E1 E
D2/E2
VIEW “A”
0.020 (0.51)
MIN
A1
A
D1
D
MIN
MAX
MILLIMETERS
MIN
0.026 (0.66)
0.032 (0.81)
A
0.165
0.180
4.20
4.57
-
0.090
0.120
2.29
3.04
-
D
0.485
0.495
12.32
12.57
-
D1
0.450
0.456
11.43
11.58
3
D2
0.191
0.219
4.86
5.56
4, 5
E
0.485
0.495
12.32
12.57
-
E1
0.450
0.456
11.43
11.58
3
E2
0.191
0.219
4.86
5.56
4, 5
N
28
28
6
Rev. 2 11/97
0.013 (0.33)
0.021 (0.53)
0.025 (0.64)
MIN
0.045 (1.14)
MIN
NOTES
A1
SEATING
-C- PLANE
0.020 (0.51) MAX
3 PLCS
MAX
VIEW “A” TYP.
NOTES:
1. Controlling dimension: INCH. Converted millimeter dimensions are
not necessarily exact.
2. Dimensions and tolerancing per ANSI Y14.5M-1982.
3. Dimensions D1 and E1 do not include mold protrusions. Allowable
mold protrusion is 0.010 inch (0.25mm) per side. Dimensions D1
and E1 include mold mismatch and are measured at the extreme
material condition at the body parting line.
4. To be measured at seating plane -C- contact point.
5. Centerline to be determined where center leads exit plastic body.
6. “N” is the number of terminal positions.
© Copyright Intersil Americas LLC 2001-2016. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN3142 Rev 10.00
Jun 14, 2016
Page 25 of 25