ICS7152AM-02T

DATASHEET ICS7152A SPREAD SPECTRUM CLOCK GENERATOR Description Features The ICS7152A-02 and -11 are clock generators for EMI (Electromagnetic Interference) reduction (see below for frequency ranges and multiplier ratios). Spectral peaks are attenuated by modulating the system clock frequency. Down or center spread profiles are selectable. Down spread will not exceed the maximum frequency of an unspread clock, and center spread does not change the average operating frequency of the system • • • • • Operating voltage of 3.3 V ±0.3 V • • • • • Low cycle-to-cycle jitter - less than 100 ps IDT offers many other clocks for computers and computer peripherals. Consult IDT when you need to remove crystals and oscillators from your board. Packaged in 8-pin SOIC Input frequency range of 16.6 to 134.0 MHz Output frequency range of 16.6 to 134.0 MHz Provides a spread spectrum clock output (±0.5%, ±1.5% center spread; -1.0%, -3.0% down spread) Advanced, low-power CMOS process Industrial and commercial temperature ranges Available in Pb (lead) free package Pin compatible with Fujitsu MB88152-102 and -111 NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 Block Diagram VDD SEL PLL Clock Synthesis and Spread Spectrum Circuitry FREQ XENS XIN CKOUT Clock Buffer/ Crystal Ocsillator XOUT External caps required with crystal for accurate tuning of the clock GND Product Lineup Product Input Frequency Range Modulation Type ICS7152AM-02, ICS7152AMI-02 40.0 MHz to 134.0 MHz Down spread ICS7152AM-11, ICS7152AMI-11 16.6 MHz to 67.0 MHz Center spread IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 1 Modulation Enable Pin Yes ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Pin Assignment Spread Direction and Percentage Select Table XIN 1 8 XENS XOUT 2 7 GND 3 SEL 4 Spread Direction Spread Percentage (%) Part Number FREQ SEL Pin 4 6 VDD 0 Center ±0.5 ICS7152AM-11 5 CKOUT Down -1.0 ICS7152AM-02 Center ±1.5 ICS7152AM-11 Down -3.0 ICS7152AM-02 1 8 pin (150 mil) SOIC Frequency Select Table Modulation Enable Select Table XENS Pin 8 Modulation 0 Modulation 1 No modulation Frequency FREQ Pin 7 0 1 16.6 to 40 MHz ICS7152AM-11 40 to 80 MHz ICS7152AM-02 33 to 67 MHz ICS7152AM-11 66 to 134 MHz ICS7152AM-02 Pin Descriptions Pin Number Pin Name Pin Type Pin Description 1 XIN Input 2 XOUT Output Crystal. 3 GND Power Connect to ground. 4 SEL Input Spread modulation select. 5 CKOUT Output Clock output. 6 VDD Power Connect to +3.3 V. 7 FREQ Input Frequency select. 8 XENS Input Modulation enable select. Crystal/clock input pin. IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 2 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG External Components Crystal caps (pF) = (CL - 6) x 2 The ICS7152A requires a minimum number of external components for proper operation. In the equation, CL is the crystal load capacitance. So, for a crystal with a 16 pF load capacitance, two 20 pF [(16-6) x 2] capacitors should be used. Decoupling Capacitor A decoupling capacitor of 0.01µF must be connected between GND and VDD on pins 3 and 6, as close to these pins as possible. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. Spread Spectrum Profile The ICS7152A low EMI clock generator uses a triangular frequency modulation profile for optimal down stream tracking of zero delay buffers and other PLL devices. The frequency modulation amplitude is constant with variations of the input frequency. Series Termination Resistor Series termination should be used on the clock output. To series terminate a 50Ω trace (a commonly used trace impedance) place a 27Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 25Ω. Frequency Modulation Rate PCB Layout Recommendations For optimum device performance and lowest output phase noise, the following guidelines should be observed. Time 1) The 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No vias should be used between the decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. 2) To minimize EMI, the 27Ω series termination resistor (if needed) should be placed close to the clock output. 3) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers. Other signal traces should be routed away from the ICS7152A. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. Crystal Information The crystal used should be a fundamental mode, parallel resonant. Crystal capacitors should be connected from pins X1 to ground and X2 to ground to optimize the initial accuracy. The value of these capacitors is given by the following equation: IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 3 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS7152A. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD -0.5 to 4.0 V All Inputs and Outputs (referenced to GND) -0.5 V to VDD+0.5 V Ambient Operating Temperature -40 to +85° C Storage Temperature -55 to +125° C Junction Temperature -40 to +125° C Soldering Temperature 260° C Overshoot (VIOVER) VDD + 1.0 V (tOVER < 50 ns) max Undershoot (VIUNDER) GND - 1.0 V (tUNDER < 50 ns) min Overshoot/Undershoot tUNDER < 50 ns VIOVER < VDD + 1.0 V VDD Input pin tOVER < 50 ns GND VIUNDER < GND - 1.0 V Recommended Operation Conditions Parameter Min. Ambient Operating Temperature -40 Power Supply Voltage (measured in respect to GND) +3.0 IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 4 Typ. 3.3 Max. Units +85 °C 3.6 V ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±0.3 V, Ambient Temperature -40 to +85° C Parameter Symbol Operating Voltage VDD Supply Current IDD Input High Voltage Input Low Voltage VIH VIL Conditions Min. Typ. Max. Units 3.0 3.3 3.6 V 10 14 mA No load, at 3.3 V, output = 24 MHz SEL, FREQ, XENS VDD x 0.8 VDD + 0.3 V XIN, Input slew rate 3 V/ns, 16.6 to 100 MHz VDD x 0.8 VDD + 0.3 V XIN, Input slew rate 3 V/ns, 100 to 134 MHz VDD x 0.9 VDD + 0.3 V SEL, FREQ, XENS GND VDD x 0.20 V XIN, Input slew rate 3 V/ns, 16.6 to 100 MHz GND VDD x 0.20 V XIN, Input slew rate 3 V/ns, 100 to 134 MHz GND VDD x 0.10 V Output High Voltage VOH CKOUT, IOH = -4 mA VDD - 0.5 VDD V Output Low Voltage VOL CKOUT, IOL = 4 mA GND 0.4 V Input Capacitance CIN XIN, SEL, XENS 16 pF CKOUT, 16.6 to 67 MHz 15 pF CKOUT, 67 to 100 MHz 10 pF CKOUT, 100 to 134 MHz 7 pF Load Capacitance Output Impedance CL ZO CKOUT, 16.6 to 134 MHz IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 5 Ω 25 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±0.3 V, Ambient Temperature -40 to +85° C Parameter Oscillation Frequency Symbol fX Conditions Max. Units 16.6 40 MHz 40 48 MHz XIN, ICS7152A-11 16.6 67 MHz XIN, ICS7152A-02 40 134 MHz CKOUT, ICS7152A-11 16.6 67 MHz CKOUT, ICS7152A-02 40 134 MHz XIN, 16.6 to 100 MHz 40 50 60 % XIN, 100 to 134 MHz 45 50 55 % CKOUT, 1.5 V 40 60 % CKOUT, 0.4 to 2.4 V, load capacitance 15 pF 0.5 TBD 3.0 V/ns TBD 100 ps 5 ms XIN, XOUT, Fundamental oscillation XIN, XOUT, 3rd over tone, note 1 Input Frequency Output Frequency Input Clock Duty Cycle Output Clock Duty Cycle fIN fOUT tDCI tDCC Output Slew Rate Min. Typ. Cycle to Cycle Jitter tJC No load, standard deviation Lock Time tLK CKOUT 2 CKOUT=TBD 33 Modulation Frequency fMOD kHz Note 1: Contact ICS Applications for more information. IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 6 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Input Frequency (fIN = 1/tIN) tIN 0.8 VDD CKIN Output Slew Rate 2.4 V 0.4 V CKOUT tr tf SR = (2.4 - 0.4) /tr, SR = (2.4 - 0.4) /tf Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR Symbol Conditions Min. Typ. Max. Units θJA Still air 150 ° C/W θJA 1 m/s air flow 140 ° C/W θJA 3 m/s air flow 120 ° C/W 40 ° C/W θJC 7 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 Symbol E A A1 B C D E e H h L α H INDEX AREA 1 2 D Min Inches* Max Min 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° *For reference only. Controlling dimensions in mm. A h x 45 A1 C -Ce B SEATING PLANE L .10 (.004) IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR C 8 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 7152AM-02* 7152AM-02T* 7152AM-02LF 7152AM-02LFT 7152AMI-02* 7152AMI-02T* 7152AMI-02LF 7152AMI-02LFT 7152AM-11* 7152AM-11T* 7152AM-11LF 7152AM-11LFT 7152AMI-11* 7152AMI-11T* 7152AMI-11LF 7152AMI-11LFT 7152AM02 7152AM02 152AM02L 152AM02L 152AMI02 152AMI02 52AMI02L 52AMI02L 7152AM11 7152AM11 7152A11L 7152A11L 7152AI11 7152AI11 152AI11L 152AI11L Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 0 to +70° C 0 to +70° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C -40 to +85° C -40 to +85° C *NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 Parts that are ordered with a “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 9 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Revision History Rev. Originator Date Description of Change A J. Sarma 10/20/05 Rev A; new device/datasheet. B 01/10/08 Updated the -11 device markings. D 11/04/09 Added EOL note for non-green parts. IDT™ / ICS™ SPREAD SPECTRUM CLOCK GENERATOR 10 ICS7152A REV D 110409 ICS7152A SPREAD SPECTRUM CLOCK GENERATOR SSCG Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA