IDT4MA100000Z3AACUGI8

100.00 MHz LVPECL Oscillator 4MA100000Z3 High Performance Differential MEMS Oscillator DATASHEET Features






Frequency: Output Type: Frequency Stability: Supply Voltage: Standard Packages: RMS phase jitter: Operating Temperature: 100.00 MHz LVPECL ± 50ppm 2.5V & 3.3V 5.0 x 3.2 mm; 7.0 x 5.0 mm 0.6ps typical (12k to 20MHz) - 40 to 85 °C 7.0 x 5.0 mm package shown (also available in 5.0 x 3.2mm pkg) Specification 2.5 V Specifications Parameter Min 2.375 Supply Voltage (VDD) Output Frequency Units Typ Max 2.50 2.625 100.00 Min 2.97 Typ Max 3.30 3.63 100.00 V MHz + 50 - 50 + 50 ppm - 50 Frequency Stability 3.3 V Specifications 95 mA us V 0. 7VDD 0. 7VDD V 0.8 VDD -1.8 1.5 VDD -1.8 V VDD -1.0 1.6 VDD -1.1 2.3 V 0.75 0.75 V VDD -1.3 V VDD -1.3 220 260 200 240 ps Supply Current Enable/Disable Time Input LOW level Input HIGH level Output LOW level Output HIGH level Amplitude (VA ) Mid Level (VM) Rise Time (TR) 100 1 0.3VDD Fall Time (TF) Symmetry (SYM) Phase Jitter Period Jitter Cycle-to-Cycle Jitter Start-up Time Aging 48 220 50 0.9 2.6 20 10 ±5 260 52 1 0.3VDD 48 Block Diagram VDD 200 50 0.6 2.4 18 10 ±5 240 52 Conditions Includes supply voltage and temperature variation (-40 to 85°C), reflow drift, and aging. No load Guaranteed by design At OE pin At OE pin Single Ended output swing (Pk-Pk) Maximum; 20/80% of VA; Output load (CL) = 2pF; Guaranteed by Char. ps % ps ps ps ms ppm Maximum; 20/80% of VA; Output load (CL) = 2pF; Guaranteed by Char. Worst case; measured at 50% of waveform 12k to 20MHz, RMS; Measured Differentially RMS 1,000 cycles, Peak Output valid time after power up, 25°C 25°C, 10 years Output Waveform OUT- TR OUT+ TF MEMS IDT MEMS ASIC Output 80% VA VM 20% SYM = t1 / t2 OE NC 7.0 x 5.0 mm 5.0 x 3.2 mm Voltage 3.3 V 2.5 V 3.3 V 2.5 V t2 GND Part Ordering Information Package Size t1 Ordering Code 4MA100000Z3AACUGI 4MA100000Z3BACUGI 4MA100000Z3AACTGI 4MA100000Z3BACTGI 4MA 100000 Z3 A A CUG I 8 Frequency Voltage Package Temperature Shipping 100.000 MHz A: 3.3 V B: 2.5 V CTG: 5.0 x 3.2 CUG: 7.0 x 5.0 I: -40 to 85°C Blank: Tubes 8: T/R * Factory minimum order quantity: 500pcs (T/R) Dec 09, 2012 ©2013 Integrated Device Technology, Inc 4MA100000Z3 Datasheet 100.00 MHz LVPECL MEMS Oscillator Pin Description Solder Reflow Profile 40 sec (max) 1 2 3 4 5 6 OE NC GND OUT+ OUT– VDD Output Enable* No Connect Ground Output Complementary Output Power Supply Voltage 245°C (260°C max) 217°C 200 150°C 100 se cm ax 150 60-150 sec 60-180 sec 3° C/ Temperature (°C) 250 max Description /sec Name 6°C Pin # * Pulled high internally 50 Time Package Outline and Dimensions 3.20 ±0.05 1.00 ±0.05 0.64 ±0.05 Typical PCB Land Pattern Pin #1 ID Chamfer 0.30 x 45° 2.60 0.85 ±0.05 0.0-0.05 VDD OE 2.54 6L SMD 5.0 x 3.2mm NC 5.00 ±0.05 1.27 Bsc GND 0.203 Ref. 5.0 ±0.05 Pin #1 ID Chamfer 0.30 x 45° OUT+ 0.90 1.50 3.60 OE VDD 5.08 6L SMD 7.0 x 5.0mm 0.85 ±0.05 0.0-0.05 1.30 ±0.05 1.50 ±0.05 OUT- 0.30 Ref NC 7.00 ±0.05 OUT- 2.54 Bsc GND 1.00 Ref 0.203 Ref. 6024 Silver Creek Valley Road San Jose, California 95138 Sales Technical Support 800-345-7015 (inside USA) +1 408-284-8200 (outside USA) MEMS_Support@idt.com www.idt.com/go/MEMS 1.60 OUT+ 1.60 Unit: (mm) DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2010, 2011, 2012. All rights reserved. Dec 09, 2012 www.IDT.com ©2013 Integrated Device Technology, Inc