IDT723612
CMOS SyncBiFIFOTM
64 x 36 x 2
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
Free-running CLKA and CLKB can be asynchronous or
coincident (simultaneous reading and writing of data on a
single clock edge is permitted)
Two independent clocked FIFOs (64 x 36 storage capacity
each) buffering data in opposite directions
Mailbox bypass Register for each FIFO
Programmable Almost-Full and Almost-Empty Flags
Microprocessor interface control logic
EFA, FFA, AEA, and AFA flags synchronized by CLKA
EFB, FFB, AEB, and AFB flags synchronized by CLKB
Passive parity checking on each port
Parity generation can be selected for each port
•
•
Supports clock frequencies up to 67 MHz
Fast access times of 10ns
Available in 132-pin plastic quad flat package (PQF) or spacesaving 120-pin thin quad flat package (TQFP)
Industrial temperature range (–40°C to +85°C) is available
Green parts available, see ordering information
DESCRIPTION
The IDT723612 is a monolithic high-speed, low-power CMOS bi-directional
clocked FIFO memory. It supports clock frequencies up to 67 MHz and has read
access times as fast as 10ns. Two independent 64 x 36 dual-port SRAM FIFOs
on board the chip buffer data in opposite directions. Each FIFO has flags to
indicate empty and full conditions and two programmable flags (Almost-Full and
FUNCTIONAL BLOCK DIAGRAM
Port-A
Control
Logic
MBF1
RAM
ARRAY
64 x 36
Device
Control
Write
Pointer
FFA
AFA
36
Read
Pointer
EFB
AEB
Status Flag
Logic
FIFO1
36
FS0
FS1
A0 - A35
Programmable Flag
Offset Register
B0 - B36
FIFO2
EFA
AEA
FFB
AFB
Status Flag
Logic
Parity
Generation
Output
Register
Read
Pointer
PGA
RAM
ARRAY
64 x 36
36
Mail 2
Register
Parity
Gen/Check
PEFA
Write
Pointer
Input
Register
ODD/
EVEN
PGB
Parity
Generation
Input
Register
RST
PEFB
Parity
Gen/Check
Mail 1
Register
Output
Register
CLKA
CSA
W/RA
ENA
MBA
Port-B
Control
Logic
MBF2
CLKB
CSB
W/RB
ENB
MBB
3136 drw01
IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc. SyncBiFIFO is a trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
© 2009 Integrated Device Technology, Inc.
FEBRUARY 2009
1
All rights reserved.
Product specifications subject to change without notice.
DSC-3136/3
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
Almost-Empty) to indicate when a selected number of words is stored in
memory. Communication between each port can bypass the FIFOs via two
36-bit mailbox registers. Each mailbox register has a flag to signal when new
mail has been stored. Parity is checked passively on each port and may be
ignored if not desired. Parity generation can be selected for data read from
each port. Two or more devices can be used in parallel to create wider data
paths.
This device is a clocked FIFO, which means each port employs a synchronous
interface. All data transfers through a port are gated to the LOW-to-HIGH
transition of a port clock by enable signals. The clocks for each port are
independent of one another and can be asynchronous or coincident. The
enables for each port are arranged to provide a simple bi-directional interface
between microprocessors and/or buses with synchronous control.
The Full Flag (FFA, FFB) and Almost-Full (AFA, AFB) flag of a FIFO are
two-stage synchronized to the port clock that writes data to its array. The Empty
Flag (EFA, EFB) and Almost-Empty (AEA, AEB) flag of a FIFO are two stage
synchronized to the port clock that reads data from its array.
The IDT723612 is characterized for operation from 0°C to 70°C.
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
GND
AEB
EFB
B0
B1
B2
GND
B3
B4
B5
B6
VCC
B7
B8
B9
GND
B10
B11
VCC
B12
COMMERCIAL
AND INDUSTRIAL
B13
B14
GND
B15
B16
B17
B18
B19
B20
GND
B21
B22
B23
VCC
A24
A25
A26
GND
A27
A28
A29
VCC
A30
A31
A32
GND
A33
A34
A35
GND
B35
B34
B33
GND
B32
B31
B30
VCC
B29
B28
B27
GND
B26
B25
B24
VCC
GND
AEA
EFA
A0
A1
A2
GND
A3
A4
A5
A6
VCC
A7
A8
A9
GND
A10
A11
VCC
A12
A13
A14
GND
A15
A16
A17
A18
A19
A20
GND
A21
A22
A23
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
AFA
FFA
CSA
ENA
CLKA
W/RA
VCC
PGA
PEFA
GND
MBF2
MBA
FS1
FS0
ODD/EVEN
RST
GND
NC
NC
NC
NC
MBB
MBF1
GND
PEFB
PGB
VCC
W/RB
CLKB
ENB
CSB
FFB
AFB
PIN CONFIGURATIONS
3136 drw02
NOTES:
1. Electrical pin 1 in center of beveled edge.
2. NC - No internal connection
3. Uses Yamaichi socket IC51-1324-828
PQFP(2) (PQ132-1, ORDER CODE: PQF)
TOP VIEW
2
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
A24
A25
A26
VCC
A27
A28
A29
GND
A30
A31
A32
A33
A34
A35
GND
B35
B34
B33
B32
B31
B30
GND
B29
B28
B27
VCC
B26
B25
B24
B23
PIN CONFIGURATIONS (CONTINUED)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
B22
B21
GND
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
GND
B9
B8
B7
VCC
B6
B5
B4
B3
GND
B2
B1
B0
EFB
AEB
AFB
AFA
FFA
CSA
ENA
CLKA
W/RA
VCC
PGA
PEFA
MBF2
MBA
FS1
FS0
ODD/EVEN
RST
GND
NC
NC
NC
NC
MBB
MBF1
PEFB
PGB
VCC
W/RB
CLKB
ENB
CSB
FFB
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
A23
A22
A21
GND
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
GND
A9
A8
A7
VCC
A6
A5
A4
A3
GND
A2
A1
A0
EFA
AEA
3136 drw03
NOTES:
1. Pin 1 identifier in corner.
2. NC - No internal connection
TQFP (PN120-1, ORDER CODE: PF)
TOP VIEW
3
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
PIN DESCRIPTION
Symbol
A0-A35
AEA
Name
Port-A Data
Almost-Empty Flag
AEB
B0-B35
CLKA
Port-B Almost-Empty
Flag
Port-A Almost-Full
Flag
Port-B Almost-Empty
Flag
Port-B Data.
Port-A Clock
CLKB
Port-B Clock
I
CSA
Port-A Chip Select
I
CSB
Port-B Chip Select
I
EFA
Port-A Empty Flag
O
(Port A)
EFB
Port-B Empty Flag
O
(Port B)
ENA
ENB
FFA
Port-A Enable
Port-B Enable
Port-A Full Flag
I
I
O
(Port A)
FFB
Port-B Full Flag
O
(Port B)
FS1, FS0
Flag-Offset Selects
I
MBA
Port-A Mailbox
Select
I
MBB
Port-B Mailbox
Select
I
MBF1
Mail1 Register Flag
O
MBF2
Mail2 Register Flag
O
AFA
AFB
I/O
I/O
O
(Port A)
O
(Port B)
O
(Port A)
O
(Port B)
I/O
I
Description
36-bit bidirectional data port for side A.
Programmable Almost-Empty flag synchronized to CLKA. It is LOW when the number of words in
the FIFO2 is less than or equal to the value in the offset register, X.
Programmable Almost-Full flag synchronized to CLKB. It is LOW when the number of words in
FIFO1 is less than or equal to the value in the offset register, X.
Programmable Almost-Full flag synchronized to CLKA. It is LOW when the number of empty
locations in FIFO1 is less than or equal to the value in the offset register, X.
Programmable Almost-Full flag synchronized to CLKB. It is LOW when the number of empty
locations in FIFO2 is less than or equal to the value in the offset register, X.
36-bit bidirectional data port for side B.
CLKA is a continuous clock that synchronizes all data transfers through port-A and can be
asynchronous or coincident to CLKB. EFA, FFA, AFA, and AEA are synchronized to the
LOW-to-HIGH transition of CLKA.
CLKB is a continuous clock that synchronizes all data transfers through port-B and can be
asynchronous or coincident to CLKA. EFB, FFB, AFB, and AEB are synchronized to the LOWto-HIGH transition of CLKB.
CSA must be LOW to enable a LOW-to-HIGH transition of CLKA to read or write data on port-A.
The A0-A35 outputs are in the high-impedance state when CSA is HIGH.
B must be LOW to enable a LOW-to-HIGH transition of CLKB to read or write data on port-B.
The B0-B35 outputs are in the high-impedance state when CSB is HIGH.
EFA is synchronized to the LOW-to-HIGH transition of CLKA. When EFA is LOW, FIFO2 is
empty, and reads from its memory are disabled. Data can be read from FIFO2 to the output
register when EFA is HIGH. EFA is forced LOW when the device is reset and is set HIGH by
the second LOW-to-HIGH transition of CLKA after data is loaded into empty FIFO2 memory.
EFB is synchronized to the LOW-to-HIGH transition of CLKB. When EFB is LOW, the FIFO1 is
empty, and reads from its memory are disabled. Data can be read from FIFO1 to the output
register when EFB is HIGH. EFB is forced LOW when the device is reset and is set HIGH by the
second LOW-to-HIGH transition of CLKB after data is loaded into empty FIFO1 memory.
ENA must be HIGH to enable a LOW-to-HIGH transition of CLKA to read or write data on port-A.
ENB must be HIGH to enable a LOW-to-HIGH transition of CLKB to read or write data on port-B.
FFA is synchronized to the LOW-to-HIGH transition of CLKA. When FFA
is LOW, FIFO1
is full,
COMMERCIAL
AND
INDUSTRIAL
and writes to its memory are disabled. FFA is forced LOW when the device is reset and is set
HIGH by the second LOW-to-HIGH transition of CLKA after reset.
FFB is synchronized to the LOW-to-HIGH transition of CLKB. When FFB is LOW, FIFO2 is full,
and writes to its memory are disabled. FFB is forced LOW when the device is reset and is set
HIGH by the second LOW-to-HIGH transition of CLKB after reset.
The LOW-to-HIGH transition of RST latches the values of FS0 and FS1, which selects one of four
preset values for the Almost-Full flag and almost-Empty flag.
A HIGH level on MBA chooses a mailbox register for a port-A read or write operation. When the
A0-A35 outputs are active, a HIGH level on MBA selects data from the mail2 register for output, and
a LOW level selects FIFO2 output register data for output.
A HIGH level on MBB chooses a mailbox register for a port-B read or write operation. When the
B0-B35 outputs are active, a HIGH level on MBB selects data from the mail1 register for output, and
a LOW level selects FIFO1 output register data for output.
MBF1 is set LOW by a LOW-to-HIGH transition of CLKA that writes data to the mail1 register.
Writes to the mail1 register are inhibited while MBF1 is set LOW. MBF1 is set HIGH by a LOWto-HIGH transition of CLKB when a port-B read is selected and MBB is HIGH. MBF1 is set HIGH
when the device is reset.
MBF2 is set LOW by a LOW-to-HIGH transition of CLKB that writes data to the mail2 register.
Writes to the mail2 register are inhibited while MBF2 is set LOW. MBF2 is set HIGH by a LOW- toHIGH transition of CLKA when a port-A read is selected and MBA is HIGH. MBF2 is set HIGH
when the device is reset.
4
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
PIN DESCRIPTION (CONTINUED)
Symbol
Name
I/O
ODD/
EVEN
Odd/Even Parity
Select
PEFA
Port-A Parity Error
Flag
O
(Port A)
PEFB
Port-B Parity Error
Flag
O
(Port B)
PGA
Port-A Parity
I
PGB
Port-B Parity
I
RST
Reset
I
W/RA
Port-A Write/Read
Select
Port-B Write/Read
Select
I
W/RB
I
I
Description
Odd parity is checked on each port when ODD/EVEN is HIGH, and even parity is checked when
ODD/EVEN is LOW. ODD/EVEN also selects the type of parity generated for each port if parity
generation is enabled for a read operation.
When any byte applied to terminals A0-A35 fails parity, PEFA is LOW. Bytes are organized as
A0-A8, A9-A17, A18-A26, and A27-A35, with the most significant bit of each byte serving as
the parity bit. The type of parity checked is determined by the state of the ODD/EVEN input. The
parity trees used to check the A0-A35 inputs are shared by the mail2 register to generate parity if
parity generation is selected by PGA. Therefore, if a mail2 read with parity generation is setup by
having W/RA LOW, MBA HIGH, and PGA HIGH, the PEFA flag is forced HIGH regardless of the
A0-A35 inputs.
When any byte applied to terminals B0-B35 fails parity, PEFB is LOW. Bytes are organized as
B0-B8, B9-B17, B18-B26, B27-B35 with the most significant bit of each byte serving as theparity bit.
The type of parity checked is determined by the state of the ODD/EVEN input. The parity trees used
to check the B0-B35 inputs are shared by the mail1 register to generate parity if parity generation is
selected by PGB. Therefore, if a mail1 read with parity generation is setup by having W/RB LOW,
MBB HIGH, and PGB HIGH, the PEFB flag is forced HIGH regardless of the state of the B0-B35
inputs.
Parity is generated for data reads from port A when PGA is HIGH. Generation The type of parity
generated is selected by the state of the ODD/EVEN input. Bytes are organized as A0-A8, A9-A17,
A18-A26, and A27-A35. The generated parity bits are output in the most significant bit of each byte.
Parity is generated for data reads from port B when PGB is HIGH. The type of parity generated is
selected by the state of the ODD/EVEN input. Bytes are organized as B0-B8, B9-B17, B18-B26,
and B27-B35. The generated parity bits are output in the most significant bit of each byte.
To reset the device, four LOW-to-HIGH transitions of CLKA and four LOW-to-HIGH transitions of
CLKB must occur while RST is LOW. This sets the AFA, AFB, MBF1, and MBF2 flags HIGH and
the EFA, EFB, AEA, AEB, FFA, and FFB flags LOW. The LOW-to-HIGH transition of RST latches
the status of the FS1 and FS0 inputs to select Almost-Full and Almost-Empty flag offset.
A HIGH selects a write operation and a LOW selects a read operation on port A for a LOW-to-HIGH
transition of CLKA. The A0-A35 outputs are in the high-impedance state when W/RA is HIGH.
A HIGH selects a write operation and a LOW selects a read operation on port B for a LOW-to-HIGH
transition of CLKB. The B0-B35 outputs are in the high-impedance state when W/RB is HIGH.
5
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
ABSOLUTE MAXIMUM RATINGS OVER OPERATING FREE-AIR TEMPERATURE
RANGE (UNLESS OTHERWISE NOTED)(2)
Symbol
V CC
VI(2)
VO(2)
IIK
IOK
I OUT
I CC
T STG
Supply Voltage Range
Input Voltage Range
Rating
Commercial
–0.5 to 7
–0.5 to VCC+0.5
Unit
V
V
Output Voltage Range
Input Clamp Current, (VI < 0 or VI > VCC)
Output Clamp Current, (VO < 0 or VO > VCC)
Continuous Output Current, (VO = 0 to VCC)
Continuous Current Through VCC or GND
Storage Temperature Range
–0.5 to VCC+0.5
±20
±50
±50
±500
–65 to 150
V
mA
mA
mA
mA
°C
NOTES:
1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device
at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended
periods may affect device reliability.
2. The input and output voltage ratings may be exceeded provided the input and output current ratings are observed.
RECOMMENDED OPERATING CONDITIONS
Symbol
V CC
VIH
VIL
IOH
IOL
TA
Parameter
Supply Voltage
HIGH Level Input Voltage
LOW-Level Input Voltage
HIGH-Level Output Current
LOW-Level Output Current
Operating Free-air Temperature
Min.
4.5
2
–
–
–
0
Max.
5.5
–
0.8
–4
8
70
Unit
V
V
V
mA
mA
°C
COMMERCIAL AND INDUSTRIAL
ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING
FREE-AIR TEMPERATURE RANGE (UNLESS OTHERWISE NOTED)
Parameter
VOH
VOL
ILI
ILO
ICC(2)
CIN
C OUT
VCC = 4.5V,
VCC = 4.5V,
VCC = 5.5V,
VCC = 5.5V,
VCC 5.5V,
VI= 0,
VO = 0,
Test Conditions
IOH = –4 mA
IOL = 8 mA
VI = VCC or 0
VO = VCC or 0
IO = 0 mA,
f = 1 MHz
f = 1 MHZ
VI = VCC or GND
Min.
2.4
—
—
—
—
—
—
Typ.(1)
—
—
—
—
—
4
8
Max.
—
0.5
±50
±50
1
—
—
Unit
V
V
µA
µA
mA
pF
pF
NOTES:
1. All typical values are at VCC = 5V, TA = 25°C.
2. For additional ICC information, see following page.
6
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
400
VCC = 5.5V
350
fdata = 1/2 fS
TA= 25°C
CL = 0 pF
mA
300
VCC = 5.0V
Supply Current
250
200
VCC = 4.5V
ICC(f)
150
100
50
0
0
10
20
30
40
50
60
70
fS ⎯ Clock Frequency ⎯ MHz
80
3136 drw04
Figure 1. Typical Characteristics: Supply Current vs Clock Frequency
CALCULATING POWER DISSIPATION
The ICC(f) current for the graph in Figure 1 was taken while simultaneously reading and writing the FIFO on the IDT723612 with CLKA and CLKB set
to fS. All data inputs and data outputs change state during each clock cycle to consume the highest supply current. Data outputs were disconnected to normalize
the graph to a zero-capacitance load. Once the capacitance load per data-output channel is known, the power dissipation can be calculated with the equation
below.
With ICC(f) taken from Figure 1, the maximum power dissipation (PD) of the IDT723612 may be calculated by:
PD = VCC x ICC(f) + Σ(CL x VCC x (VOH - VOL) x fo)
where:
CL
fo
VOH
VOL
=
=
=
=
output capacitance load
switching frequency of an output
output HIGH level voltage
output LOW level voltage
When no reads or writes are occurring on the IDT723612, the power dissipated by a single clock (CLKA or CLKB) input running at frequency fS is
calculated by:
PT = VCC x fS x 0.290 mA/MHz
7
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
DC ELECTRICAL CHARACTERISTICS OVER RECOMMENDED RANGES OF
SUPPLY VOLTAGE AND OPERATING FREE-AIR TEMPERATURE
(Commercial: VCC = 5.0V ±10%, TA = 0°C to +70°C; Industrial; VCC = 5.0V ± 10%,TA = 40°C to +85°C)
Symbol
fS
tCLK
tCLKH
tCLKL
tDS
tENS1
tENS2
tENS3
tPGS
tRSTS
tFSS
tDH
tENH1
tENH2
tENH3
tPGH
tRSTH
tFSH
tSKEW1(4)
tSKEW2(4)
Parameter
Clock Frequency, CLKA or CLKB
Clock Cycle Time, CLKA or CLKB
Pulse Duration, CLKA and CLKB HIGH
Pulse Duration, CLKA and CLKB LOW
Setup Time, A0-A35 before CLKA↑ and B0-B35 before CLKB↑
Setup Time, CSA, W/RA before CLKA↑; CSB, W/RB before CLKB↑
Setup Time, ENA, before CLKA↑; ENB before CLKB↑
Setup Time, MBA before CLKA↑: MBB before CLKB↑
Setup Time, ODD/EVEN and PGA before CLKA↑; ODD/EVEN and PGB
before CLKB↑(2 )
Setup Time, RST LOW before CLKA↑ or CLKB↑(3)
Setup Time, FS0/FS1 before RST HIGH
Hold Time, A0-A35 after CLKA↑ and B0-B35 after CLKB↑
Hold Time, CSA W/RA after CLKA↑; CSB, W/RB after CLKB↑
Hold Time, ENA, after CLKA↑; ENB after CLKB↑
Hold Time, MBA after CLKA↑; MBB after CLKB↑
Hold Time, ODD/EVEN and PGA after CLKA↑; ODD/EVEN and PGB
after CLKB↑(2 )
Hold Time, RST LOW after CLKA↑ or CLKB↑(3)
Hold Time, FS0 and FS1 after RST HIGH
Skew Time, between CLKA↑ and CLKB↑ for EFA, EFB, FFA, and FFB
Skew Time, between CLKA↑ and CLKB↑ For AEA, AEB, AFA, and AFB
Commercial
Com’l & Ind’l(1)
IDT723612L15
Min.
Max.
–
66.7
15
–
6
–
6
–
4
–
6
–
4
–
4
–
4
–
IDT723612L20
Min.
Max.
–
50
20
–
8
–
8
–
5
–
6
–
5
–
5
–
5
–
Unit
MHz
ns
ns
ns
ns
ns
ns
ns
ns
5
5
2.5
2
2.5
1
1
–
–
–
–
–
–
–
6
6
2.5
2
2.5
1
1
–
–
–
–
–
–
–
ns
ns
ns
ns
ns
ns
ns
5
4
8
14
–
–
–
–
6
4
8
16
–
–
–
–
ns
ns
ns
ns
NOTES:
COMMERCIAL AND INDUSTRIAL
1. Industrial temperature range product for 20ns speed grade is available as a standard device. All other speed grades are available by special order.
2. Only applies for a clock edge that does a FIFO read.
3. Requirement to count the clock edge as one of at least four needed to reset a FIFO.
4. Skew time is not a timing constraint for proper device operation and is only included to illustrate the timing relationship between CLKA cycle and CLKB cycle.
8
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
SWITCHING CHARACTERISTICS OVER RECOMMENDED RANGES OF SUPPLY
VOLTAGE AND OPERATING FREE-AIR TEMPERATURE, CL = 30PF
(Commercial: VCC = 5.0V ±10%, TA = 0°C to +70°C; Industrial; VCC = 5.0V ± 10%,TA = 40°C to +85°C)
Symbol
tA
tWFF
tREF
tPAE
tPAF
tPMF
tPMR
tMDV
tPDPE
tPOPE
tPOPB(4)
tPEPE
tPEPB(4)
tRSF
tEN
tDIS
Parameter
Access Time, CLKA↑ to A0-A35 and CLKB↑ to B0-B35
Propagation Delay Time, CLKA↑ to FFA and CLKB↑ to FFB
Propagation Delay Time, CLKA↑ to EFA and and CLKB↑ to EFB
Propagation Delay Time, CLKA↑ to AEA and CLKB↑ to AEB
Propagation Delay Time, CLKA↑ to AFA and CLKB↑ to AFB
Propagation Delay Time, CLKA↑ to MBF1 LOW or MBF2 HIGH and CLKB↑ to
MBF2 LOW or MBF1 HIGH
Propagation Delay Time, CLKA↑ to B0-B35(2) and CLKB↑ to A0-A35(3)
Propagation Delay Time, MBA to A0-A35 valid and MBB to B0-B35 valid
Propagation Delay Time, A0-A35 valid to PEFA valid; B0-B35 valid to PEFB valid
Propagation Delay Time, ODD/EVEN to PEFA and PEFB
Propagation Delay Time, ODD/EVEN to parity bits (A8, A17, A26, A35) and
(B8, B17, B26, B35)
Propagation Delay Time, W/RA, CSA, ENA, MBA or PGA to PEFA; W/RB, CSB,
ENB, MBB, PGB to PEFB
Propagation Delay Time, W/RA, CSA, ENA, MBA or PGA to parity bits ( A8, A17, A26, A35);
W/RB, CSB, bits (B8, B17, B26, B35) ENB, MBB or PGB to parity
Propagation Delay Time, RST to (AEA, AEB) LOW and (AFA, AFB, MBF1, MBF2)
HIGH
Enable Time, CSA and W/RA LOW to A0-A35 active and CSB LOW and W/RB HIGH
to B0-B35 active
Disable Time, CSA or W/RA HIGH to A0-A35 at high impedance and CSB HIGH
or W/RB LOW to B0-B35 at high impedance.
Commercial
Com’l & Ind’l(1)
IDT723612L15
Min.
Max.
2
10
2
10
2
10
2
10
2
10
1
9
IDT723612L20
Min.
Max.
2
12
2
12
2
12
2
12
2
12
1
12
Unit
ns
ns
ns
ns
ns
ns
3
1
3
3
2
11
11
10
11
11
3
1
3
3
2
13
11.5
11
12
12
ns
ns
ns
ns
ns
1
11
1
12
ns
3
12
3
13
ns
1
15
1
20
ns
2
10
2
12
ns
1
8
1
9
ns
NOTES:
1. Industrial temperature range product for 20ns speed grade is available as a standard device. All other speed grades are available by special order.
2. Writing data to the mail1 register when the B0-B35 outputs are active and MBB is HIGH.
3 Writing data to the mail2 register when the A0-A35 outputs are active and MBA is HIGH.
4. Only applies when reading data from a mail register.
9
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
SIGNAL DESCRIPTIONS
RESET
The IDT723612 is reset by taking the Reset (RST) input LOW for at least
four port-A clock (CLKA) and four port-B Clock (CLKB) LOW-to-HIGH
transitions. The Reset input can switch asynchronously to the clocks. A device
reset initializes the internal read and write pointers of each FIFO and forces
the Full Flags (FFA, FFB) LOW, the Empty Flags (EFA, EFB) LOW, the AlmostEmpty flags (AEA, AEB) LOW and the Almost-Full flags (AFA, AFB) HIGH. A
reset also forces the Mailbox Flags (MBF1, MBF2) HIGH. After a reset, FFA
is set HIGH after two LOW-to-HIGH transitions of CLKA and FFB is set HIGH
after two LOW-to-HIGH transitions of CLKB. The device must be reset after
power up before data is written to its memory.
TABLE 1 — FLAG PROGRAMMING
FS1
FS0
RST
H
H
L
L
H
L
H
L
↑
↑
↑
↑
ALMOST-FULL AND
ALMOST-EMPTY FLAG
OFFSET REGISTER (X)
16
12
8
4
A LOW-to-HIGH transition on the RST input loads the Almost-Full and
Almost-Empty registers (X) with the values selected by the Flag Select (FS0,
FS1) inputs. The values that can be loaded into the registers are shown in
Table 1.
FIFO WRITE/READ OPERATION
The state of port-A data A0-A35 outputs is controlled by the port-A Chip
Select (CSA) and the port-A Write/Read select (W/RA). The A0-A35 outputs
are in the high-impedance state when either CSA or W/RA is HIGH. The A0A35 outputs are active when both CSA and W/RA are LOW.
Data is loaded into FIFO1 from the A0-A35 inputs on a LOW-to-HIGH
transition of CLKA when CSA is LOW, W/RA is HIGH, ENA is HIGH, MBA
is LOW, and FFA is HIGH. Data is read from FIFO2 to the A0-A35 outputs by
a LOW-to-HIGH transition of CLKA when CSA is LOW, W/RA is LOW, ENA is
HIGH, MBA is LOW, and EFA is HIGH (see Table 2).
The port-B control signals are identical to those of port A. The state of the
port-B data (B0-B35) outputs is controlled by the port-B Chip Select (CSB) and
the port-B Write/Read select (W/RB). The B0-B35 outputs are in the highimpedance state when either CSB or W/RB is HIGH. The B0-B35 outputs are
active when both CSB and W/RB are LOW.
Data is loaded into FIFO2 from the B0-B35 inputs on a LOW-to-HIGH
transition of CLKB when CSB is LOW, W/RB is HIGH, ENB is HIGH, MBB is
LOW, and FFB is HIGH. Data is read from FIFO1 to the B0-B35 outputs by
a LOW-to-HIGH transition of CLKB when CSB is LOW, W/RB is LOW, ENB is
HIGH, MBB is LOW, and EFB is HIGH (see Table 3).
TABLE 2 — PORT-A ENABLE FUNCTION TABLE
CSA
H
L
L
L
L
L
L
L
W/RA
X
H
H
H
L
L
L
L
ENA
X
L
H
H
L
H
L
H
MBA
X
X
L
H
L
L
H
H
CLKA
X
X
↑
↑
X
↑
X
↑
A0-A35 Outputs
In High-Impedance State
In High-Impedance State
In High-Impedance State
In High-Impedance State
Active, FIFO2 Output Register
Active, FIFO2 Output Register
Active, Mail2 Register
Active, Mail2 Register
Port Functions
None
None
FIFO1 Write AND INDUSTRIAL
COMMERCIAL
Mail1 Write
None
FIFO2 Read
None
Mail2 Read (Set MBF2 HIGH)
TABLE 3 — PORT-B ENABLE FUNCTION TABLE
CSB
H
L
L
L
L
L
L
L
W/RB
X
H
H
H
L
L
L
L
ENB
X
L
H
H
L
H
L
H
MBB
X
X
L
H
L
L
H
H
CLKB
X
X
↑
↑
X
↑
X
↑
B0-B35 Outputs
In High-Impedance State
In High-Impedance State
In High-Impedance State
In High-Impedance State
Active, FIFO1 Output Register
Active, FIFO1 Output Register
Active, Mail1 Register
Active, Mail1 Register
10
Port Functions
None
None
FIFO2 Write
Mail2 Write
None
FIFO1 read
None
Mail1 Read (Set MBF1 HIGH)
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
The setup and hold time constraints to the port clocks for the port Chip Selects
(CSA, CSB) and Write/Read selects (W/RA, W/RB) are only for enabling write
and read operations and are not related to high-impedance control of the data
outputs. If a port enable is LOW during a clock cycle, the port chip select and
write/read select may change states during the setup and hold time window
of the cycle.
SYNCHRONIZED FIFO FLAGS
Each FIFO is synchronized to its port clock through two flip-flop stages. This
is done to improve flag reliability by reducing the probability of metastable
events on the output when CLKA and CLKB operate asynchronously to one
another. EFA, AEA, FFA, and AFA are synchronized by CLKA. EFB, AEB,
FFB, and AFB are synchronized to CLKB. Tables 4 and 5 show the relationship
of each port flag to FIFO1 and FIFO2.
Each time a word is written to a FIFO, the write pointer is incremented. The
state machine that controls a Full Flag monitors a write-pointer and read pointer
comparator that indicates when the FIFO SRAM status is full, full-1, or full-2.
From the time a word is read from a FIFO, the previous memory location is
ready to be written in a minimum of three cycles of the Full Flag synchronizing
clock. Therefore, a Full Flag is LOW if less than two cycles of the Full Flag
synchronizing clock have elapsed since the next memory write location has
been read. The second LOW-to-HIGH transition on the Full Flag synchronization clock after the read sets the Full Flag HIGH and the data can be written
in the following clock cycle.
A LOW-to-HIGH transition on a Full Flag synchronizing clock begins the
first synchronization cycle of a read if the clock transition occurs at time tSKEW1
or greater after the read. Otherwise, the subsequent clock cycle can be the first
synchronization cycle.
EMPTY FLAGS (EFA, EFB)
The Empty Flag of a FIFO is synchronized to the port clock that reads
data from its array. When the Empty Flag is HIGH, new data can be read to
the FIFO output register. When the Empty Flag is LOW, the FIFO is empty and
attempted FIFO reads are ignored.
The read pointer of a FIFO is incremented each time a new word is
clocked to the output register. The state machine that controls an Empty Flag
monitors a write-pointer and read-pointer comparator that indicates when the
FIFO SRAM status is empty, empty+1, or empty+2. A word written to a FIFO
can be read to the FIFO output register in a minimum of three cycles of the Empty
Flag synchronizing clock. Therefore, an Empty Flag is LOW if a word in memory
is the next data to be sent to the FIFO output register and two cycles of the port
clock that reads data from the FIFO have not elapsed since the time the word
was written. The Empty Flag of the FIFO is set HIGH by the second LOW-toHIGH transition of the synchronizing clock, and the new data word can be read
to the FIFO output register in the following cycle.
A LOW-to-HIGH transition on an Empty Flag synchronizing clock begins the
first synchronization cycle of a write if the clock transition occurs at time tSKEW1
or greater after the write. Otherwise, the subsequent clock cycle can be the first
synchronization cycle.
ALMOST EMPTY FLAGS (AEA, AEB)
The Almost-Empty flag of a FIFO is synchronized to the port clock that
reads data from its array. The state machine that controls an Almost-Empty flag
monitors a write-pointer comparator that indicates when the FIFO SRAM status
is almost-empty, almost-empty+1, or almost-empty+2. The almost-empty state
is defined by the value of the Almost-Full and Almost-Empty Offset register (X).
This register is loaded with one of four preset values during a device reset (see
Reset above). An Almost-Empty flag is LOW when the FIFO contains X or less
words in memory and is HIGH when the FIFO contains (X+1) or more words.
Two LOW-to-HIGH transitions of the Almost-Empty flag synchronizing clocks
are required after a FIFO write for the Almost-Empty flag to reflect the new level
of fill. Therefore, the Almost-Empty flag of a FIFO containing (X+1) or more
words remains LOW if two cycles of the synchronizing clock have not elapsed
since the write that filled the memory to the (X+1) level. An Almost-Empty flag
is set HIGH by the second LOW-to-HIGH transition of the synchronizing clock
after the FIFO write that fills memory to the (X+1) level. A LOW-to-HIGH
transition of an Almost-Empty flag synchronizing clock begins the first synchronization cycle if it occurs at time tSKEW2 or greater after the write that fills the FIFO
to (X+1) words. Otherwise, the subsequent synchronizing clock cycle can be
the first synchronization cycle (see Figure 7 and 8).
FULL FLAG (FFA, FFB)
The Full Flag of a FIFO is synchronized to the port clock that writes data to
its array. When the Full Flag is HIGH, a memory location is free in the SRAM
to receive new data. No memory locations are free when the Full Flag is LOW
and attempted writes to the FIFO are ignored.
ALMOST FULL FLAGS (AFA, AFB)
The Almost-Full flag of a FIFO is synchronized to the port clock that writes
data to its array. The state machine that controls an Almost-Full flag monitors
a write-pointer and read-pointer comparator that indicates when the FIFO
TABLE 4 — FIFO1 FLAG OPERATION
TABLE 5 — FIFO2 FLAG OPERATION
Number of Words
in the FIFO1(1)
0
1 to X
(X+1) to [64–(X+1)]
(64–X) to 63
64
Synchronized
to CLKB
EFB
AEB
L
L
H
L
H
H
H
H
H
H
Synchronized
to CLKA
AFA
FFA
H
H
H
H
H
H
L
H
L
L
Number of Words
in the FIFO1(1)
0
1 to X
(X+1) to [64–(X+1)]
(64–X) to 63
64
Synchronized
to CLKB
EFA
AEA
L
L
H
L
H
H
H
H
H
H
Synchronized
to CLKA
AFB
FFB
H
H
H
H
H
H
L
H
L
L
NOTE:
1. X is the value in the Almost-Empty flag and Almost-Full flag offset register.
11
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
SRAM status is almost-full, almost-full-1, or almost-full-2. The almost-full state
is defined by the value of the Almost-Full and Almost-Empty Offset register (X).
This register is loaded with one of four preset values during a device reset (see
Reset above). An Almost-Full flag is LOW when the FIFO contains (64-X) or
more words in memory and is HIGH when the FIFO contains [64-(X+1)] or
less words.
Two LOW-to-HIGH transitions of the Almost-Full flag synchronizing clock are
required after a FIFO read for the Almost-Full flag to reflect the new level of fill.
Therefore, the Almost-Full flag of a FIFO containing [64-(X+1)] or less words
remains LOW if two cycles of the synchronizing clock have not elapsed since
the read that reduced the number of words in memory to [64-(X+1)]. An AlmostFull flag is set HIGH by the second LOW-to-HIGH transition of the synchronizing
clock after the FIFO read that reduces the number of words in memory to [64(X+1)]. A second LOW-to-HIGH transition of an Almost-Full flag synchronizing
clock begins the first synchronization cycle if it occurs at time tSKEW2 or greater
after the read that reduces the number of words in memory to [64-(X+1)].
Otherwise, the subsequent synchronizing clock cycle can be the first synchronization cycle (see Figure 14 and 15).
MAILBOX REGISTERS
Each FIFO has a 36-bit bypass register to pass command and control
information between port A and port B without putting it in queue. The Mailbox
select (MBA, MBB) inputs choose between a mail register and a FIFO for a
port data transfer operation. A LOW-to-HIGH transition on CLKA writes A0A35 data to the mail1 register when a port-A write is selected by CSA, W/RA,
and ENA and MBA HIGH. A LOW-to-HIGH transition on CLKB writes B0-B35
data to the mail2 register when a port-B write is selected by CSB, W/RB, and
ENB and MBB is HIGH. Writing data to a mail register sets the corresponding
flag (MBF1 or MBF2) LOW. Attempted writes to a mail register are ignored while
the mail flag is LOW.
When a port's data outputs are active, the data on the bus comes from the
FIFO output register when the port Mailbox-select input (MBA, MBB) is LOW
and from the mail register when the port mailbox-select input is HIGH. The Mail1
register Flag (MBF1) is set HIGH by a LOW-to-HIGH transition on CLKB when
a port-B read is selected by CSB, W/RB, and ENB and MBB is HIGH. The Mail2
register Flag (MBF2) is set HIGH by a LOW-to-HIGH transition on CLKA when
port-A read is selected by CSA, W/RA, and ENA and MBA is HIGH. The data
in a mail register remains intact after it is read and changes only when new data
is written to the register.
PARITY CHECKING
The port-A inputs (A0-A35) and port-B inputs (B0-B35) each have four
parity trees to check the parity of incoming (or outgoing) data. A parity failure
on one or more bytes of the input bus is reported by a LOW level on the port
Parity Error Flag (PEFA, PEFB). Odd or even parity checking can be selected,
and the Parity Error Fags can be ignored if this feature is not desired.
Parity status is checked on each input bus according to the level of the Odd/
Even parity (ODD/EVEN) select input. A parity error on one or more bytes of
a port is reported by a LOW level on the corresponding port Parity Error Flag
(PEFA, PEFB) output. Port-A bytes are arranged as A0-A8, A9-A17, A18A26, and A27-A35 with the most significant bit of each byte used as the parity
bit. Port-B bytes are arranged as B0-B8, B9-B17, B18-B26, and B27-B35,
with the most significant bit of each byte used as the parity bit. When odd/even
parity is selected, a port parity error flag (PEFA, PEFB) is LOW if any byte on
the port has an odd/even number of LOW levels applied to the bits.
The four parity trees used to check the A0-A35 inputs are shared by the mail2
register when parity generation is selected for port-A reads (PGA = HIGH).
When a port-A read from the mail2 register with parity generation is selected
with W/RA LOW, CSA LOW, ENA HIGH, MBA HIGH, and PGA HIGH, the portA Parity Error Flag (PEFA) is held HIGH regardless of the levels applied to
the A0-A35 inputs. Likewise, the parity trees used to check the B0-B35 inputs
are shared by the mail1 register when parity generation is selected for portB reads (PGB = HIGH). When a port-B read from the mail1 register with parity
generation is selected with W/RB LOW, CSB LOW, ENB HIGH, MBB HIGH,
and PGB HIGH, the port-B parity error flag (PEFB) is held HIGH regardless
of the levels applied to the B0-B35 inputs.
PARITY GENERATION
A HIGH level on the port-A Parity Generate select (PGA) or port-B Parity
Generate select (PGB) enables the IDT723612 to generate parity bits for
port reads from a FIFO or mailbox register. Port-A bytes are arranged as A0A8, A9-A17, A18-26, and A27-A35, with the most significant bit of each byte
used as the parity bit. Port-B bytes are arranged as B0-B8, B9-B17, B18-B26,
and B27-B35, with the most significant bit of each byte used as the parity bit.
A write to a FIFO or mail register stores the levels applied to all thirty-six inputs
regardless of the state of the Parity Generate select (PGA, PGB) inputs. When
data is read from a port with parity generation selected, the lower eight bits of
each byte are used to generate a parity bit according to the level on the ODD/
EVEN select. The generated parity bits are substituted for the levels originally
written to the most significant bits of each byte as the word is read to the data
outputs.
Parity bits for FIFO data are generated after the data is read from SRAM
and before the data is written to the output register. Therefore, the port-A parity
generate select (PGA) and Odd/Even parity select (ODD/EVEN) have setup
and hold time constraints to the port-A Clock (CLKA) and the port-B Parity
COMMERCIAL
AND
INDUSTRIAL
Generate select (PGB) and ODD/EVEN have setup
and hold-time
constraints
to the port-B Clock (CLKB). These timing constraints only apply for a rising clock
edge used to read a new word to the FIFO output register.
The circuit used to generate parity for the mail1 data is shared by the portB bus (B0-B35) to check parity and the circuit used to generate parity for the
mail2 data is shared by the port-A bus (A0-A35) to check parity. The shared
parity trees of a port are used to generate parity bits for the data in a mail register
when the port Write/Read select (W/RA, W/RB) input is LOW, the port mail select
(MBA, MBB) input is HIGH, Chip Select (CSA, CSB) is LOW, Enable (ENA,
ENB) is HIGH, and port Parity Generate select (PGA, PGB) is HIGH.
Generating parity for mail register data does not change the contents of the
register.
12
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
CLKA
tRSTH
CLKB
tRSTS
tFSS
tFSH
RST
0,1
FS1,FS0
tWFF
tWFF
FFA
tREF
EFA
tWFF
tWFF
FFB
tREF
EFB
tPAE
AEA
tPAF
AFA
MBF1,
MBF2
tRSF
tPAE
AEB
tPAF
AFB
3136 drw05
Figure 2. Device Reset Loading the X Register with the Value of Eight
13
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
tCLK
tCLKL
tCLKH
CLKA
FFA HIGH
tENS1
tENH1
tENS1
tENH1
tENS3
tENH3
tENS2
tENH2
CSA
W/RA
MBA
tENS2
tENH2
tENS2
tENH2
ENA
tDS
tDH
(1)
A0 - A35
W2(1)
W1
ODD/
EVEN
tPDPE
PEFA
No Operation
tPDPE
Valid
Valid
3136 drw06
NOTE:
1. Written to FIFO1.
Figure 3. Port-A Write Cycle Timing for FIFO1
tCLK
tCLKH
tCLKL
CLKB
FFB HIGH
COMMERCIAL AND INDUSTRIAL
tENS1
tENH1
tENS1
tENH1
tENS3
tENH3
tENS2
tENH2
CSB
W/RB
MBB
tENS2
tENH2
tENS2
tENH2
ENB
tDS
B0 - B35
ODD/
EVEN
PEFB
tDH
(1)
W2(1)
W1
tPDPE
No Operation
tPDPE
Valid
Valid
3136 drw07
NOTE:
1. Written to FIFO2.
Figure 4. Port-B Write Cycle Timing for FIFO2
14
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
tCLK
tCLKH
tCLKL
CLKB
EFB
HIGH
CSB
W/RB
tENS2
MBB
tENH2
tENS2
tENH2
tENH2
tENS2
ENB
tMDV
tEN
B0 - B35
tA
tA
(1)
Previous Data
tPGH
tPGS
PGB,
ODD/
EVEN
(1)
tDIS
Word 2 (1)
Word 1
tPGS
No Operation
tPGH
3136 drw08
NOTE:
1. Read from FIFO1.
Figure 5. Port-B Read Cycle Timing for FIFO1
tCLK
tCLKH
tCLKL
CLKA
EFA
HIGH
CSA
W/RA
tENS2
MBA
tENH2
tENS2
tENH2
tENH2
tENS2
ENA
tMDV
A0 - A35
PGA,
ODD/
EVEN
tEN
tA
tA
(1)
Previous Data
tPGH
tPGS
(1)
Word 1
tPGS
No Operation
Word 2
tDIS
(1)
tPGH
3136 drw09
NOTE:
1. Read from FIFO2.
Figure 6. Port-A Read Cycle Timing for FIFO2
15
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
tCLK
tCLKH tCLKL
CLKA
CSA LOW
WRA HIGH tENS3
MBA
tENS2
ENA
FFA HIGH
A0 - A35
tENH3
tENH2
tDS
tDH
W1
(1)
tSKEW1
CLKB
EFB
tCLK
tCLKH tCLKL
1
2
tREF
tREF
FIFO1 Empty
CSB LOW
W/RB
LOW
MBB LOW
tENS2
tENH2
ENB
tA
B0 -B35
W1
3136 drw10
NOTE:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for EFB to transition HIGH in the next CLKB cycle. If the time between the rising
CLKA edge and rising CLKB edge is less than tSKEW1, then the transition of EFB HIGH may occur one CLKB cycle later than shown.
Figure 7. EFB Flag Timing and First Data Read when FIFO1 is Empty
COMMERCIAL AND INDUSTRIAL
16
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
tCLK
tCLKH tCLKL
CLKB
CSB
LOW
W/RB HIGH
tENS3
tENH3
tENS2
tENH2
MBB
ENB
FFB HIGH
B0 - B35
tDS
tDH
W1
(1)
tSKEW1
CLKA
EFA
tCLK
tCLKH tCLKL
1
2
tREF
tREF
FIFO2 Empty
CSA
LOW
W/RA
LOW
MBA
LOW
tENS2
tENH2
ENA
tA
A0 -A35
W1
3136 drw11
NOTE:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for EFA to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge
and rising CLKA edge is less than tSKEW1, then the transition of EFA HIGH may occur one CLKA cycle later than shown.
Figure 8. EFA Flag Timing and First Data Read when FIFO2 is Empty
17
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
tCLKH
tCLK
tCLKL
CLKB
CSB
LOW
W/RB
LOW
MBB
LOW
tENS2
tENH2
ENB
EFB
B0 - B35
HIGH
tA
Previous Word in FIFO1 Output Register
tSKEW1(1)
CLKA
Next Word From FIFO1
tCLKH
1
tCLK
tCLKL
2
tWFF
FFA
tWFF
FIFO1 Full
CSA
LOW
WRA
HIGH
tENS3
tENH3
tENS2
tENH2
MBA
ENA
tDH
tDS
A0 - A35
To FIFO1
3136 drw12
NOTE:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for FFA to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge
and rising CLKA edge is less than tSKEW1, then FFA may transition HIGH one CLKA cycle later than shown.
Figure 9. FFA Flag Timing and First Available Write when FIFO1 is Full
COMMERCIAL AND INDUSTRIAL
18
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
tCLK
tCLKH
tCLKL
CLKA
CSA
LOW
W/RA
LOW
MBA
LOW
tENS2
tENH2
ENA
EFA
A0 - A35
HIGH
tA
Previous Word in FIFO2 Output Register
Next Word From FIFO2
tSKEW1(1)
CLKB
tCLKH
1
tCLK
tCLKL
2
tWFF
tWFF
FFB
FIFO2 Full
CSB
LOW
W/RB
HIGH
tENS3
tENH3
tENS2
tENH2
MBB
ENB
tDH
tDS
B0 - B35
3136 drw13
To FIFO2
NOTE:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for FFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge
and rising CLKB edge is less than tSKEW1, then FFB may transition HIGH one CLKB cycle later than shown.
Figure 10. FFB Flag Timing and First Available Write when FIFO2 is Full
CLKA
tENS2
tENH2
ENA
tSKEW2(1)
CLKB
1
2
tPAE
AEB
X Word in FIFO1
tPAE
(X+1) Words in FIFO1
tENS2
tENH2
ENB
3136 drw14
NOTES:
1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AEB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge
and rising CLKB edge is less than tSKEW2, then AEB may transition HIGH one CLKB cycle later than shown.
2. FIFO1 Write (CSA = LOW, W/RA = HIGH, MBA = LOW), FIFO1 read (CSB = LOW, W/RB = LOW, MBB = LOW).
Figure 11. Timing for AEB when FIFO1 is Almost Empty
19
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
CLKB
tENS2
tENH2
ENB
tSKEW2(1)
1
CLKA
2
tPAE
tPAE
AEA
(X+1) Words in FIFO2
X Words in FIFO2
tENS2
tENH2
ENA
3136 drw15
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AEA to transition HIGH in the next CLKA cycle. If the time between the rising
CLKB edge and rising CLKA edge is less than tSKEW2, then AEA may transition HIGH one CLKA cycle later than shown.
2. FIFO2 Write (CSB = LOW, W/RB = HIGH, MBB = LOW), FIFO2 read (CSA = LOW, W/RA = LOW, MBA = LOW).
Figure 12. Timing for AEA when FIFO2 is Almost Empty
tSKEW2(1)
1
CLKA
tENS2
2
tENH2
ENA
tPAF
AFA
tPAF
(64-X) Words in FIFO1
[64-(X+1)] Words in FIFO1
CLKB
tENS2
tENH2
ENB
3136 drw16
NOTES:
1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AFA to transition HIGH in the next CLKA cycle. If the time between the rising
CLKA edge and rising CLKB edge is less than tSKEW2, then AFA may transition HIGH one CLKB cycle later than shown.
2. FIFO1 Write (CSA = LOW, W/RA = HIGH, MBA = LOW), FIFO1 read (CSB = LOW, W/RB = LOW, MBB = LOW).
Figure 13. Timing for AFA when FIFO1 is Almost Full
COMMERCIAL AND INDUSTRIAL
tSKEW2(1)
1
CLKB
tENS2
2
tENH2
ENB
AFB
tPAF
[64-(X+1)] Words in FIFO2
tPAF
(64-X) Words in FIFO2
CLKA
tENS2
tENH2
ENA
3136 drw17
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AFB to transition HIGH in the next CLKB cycle. If the time between the rising
CLKB edge and rising CLKA edge is less than tSKEW2, then AFB may transition HIGH one CLKA cycle later than shown.
2. FIFO2 Write (CSB = LOW, W/RB = HIGH, MBB = LOW), FIFO2 read (CSA = LOW, W/RA = LOW, MBA = LOW).
Figure 14. Timing for AFB when FIFO2 is Almost Full
20
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
CLKA
CSA
tENS1
tENH1
tENS1
tENH1
tENS1
tENH1
tENS1
tENH1
W/RA
MBA
ENA
tDS
W1
A0 - A35
tDH
CLKB
tPMF
tPMF
MBF1
CSB
W/RB
MBB
tENS2
tENH2
ENB
tEN
tMDV
tPMR
tDIS
W1 (Remains valid in Mail1 Register after read)
B0 - B35
3136 drw18
FIFO1 Output Register
NOTE:
1. Port-B parity generation off (PGB = LOW).
Figure 15. Timing for Mail1 Register and MBF1 Flag
21
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
W1 (Remains valid in Mail2 Register after read)
NOTE:
1. Port-A parity generation off (PGA = LOW).
Figure 16. Timing for Mail2 Register and MBF2 Flag
COMMERCIAL AND INDUSTRIAL
ODD/
EVEN
W/RA
MBA
PGA
PEFA
tPOPE
Valid
tPOPE
Valid
tPEPE
Valid
tPEPE
Valid
3136 drw20
NOTE:
1. ENA is HIGH, and CSA is LOW.
Figure 17. ODD/EVEN W/RA, MBA, and PGA to PEFA Timing
22
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
ODD/
EVEN
W/RB
MBB
PGB
tPOPE
PEFB
Valid
tPEPE
tPOPE
Valid
Valid
tPEPE
Valid
3136 drw21
NOTE:
1. ENB is HIGH, and CSB is LOW.
Figure 18. ODD/EVEN W/RB, MBB, and PGB to PEFB Timing
ODD/
EVEN
CSA
LOW
W/RA
MBA
PGA
A8, A17,
A26, A35
tEN
tPEPB
tMDV
tPOPB
Generated Parity
tPEPB
Generated Parity
Mail2
Data
Mail2 Data
3136 drw22
NOTE:
1. ENA is HIGH.
Figure 19. Parity Generation Timing when Reading from Mail2 Register
ODD/
EVEN
CSB LOW
W/RB
MBB
PGB
B8, B17,
B26, B35
tEN
tPEPB
tMDV
tPOPB
Generated Parity
tPEPB
Generated Parity
Mail1
Data
Mail1 Data
3136 drw23
NOTE:
1. ENB is HIGH.
Figure 20. Parity Generation Timing when Reading from Mail1 Register
23
FEBRUARY 13, 2009
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT723612
CMOS SYNCBiFIFOTM 64 x 36 x 2
PARAMETER MEASUREMENT INFORMATION
5V
1.1 k Ω
From Output
Under Test
30 pF
680 Ω
(1)
LOAD CIRCUIT
3V
1.5 V
Timing
Input
GND
tS
th
GND
tW
3V
1.5 V
1.5 V
1.5 V
1.5 V
3V
Data,
Enable
Input
Low-Level
Input
GND
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
1.5 V
1.5 V
GND
VOLTAGE WAVEFORMS
PULSE DURATIONS
3V
Output
Enable
1.5 V
tPLZ
1.5 V
tPZL
GND
≈3 V
Input
1.5 V
Low-Level
Output
VOL
tPZH
VOH
High-Level
Output
3V
High-Level
Input
1.5 V
tPHZ
3V
1.5 V
1.5 V
tPD
tPD
VOH
In-Phase
Output
≈ OV
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
GND
1.5 V
1.5 V
VOL
COMMERCIAL AND INDUSTRIAL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
3136 drw24
NOTE:
1. Includes probe and jig capacitance.
Figure 21. Load Circuit and Voltage Waveforms
24
FEBRUARY 13, 2009
ORDERING INFORMATION
XXXXXX
Device Type
X
Power
XX
Speed
X
Package
X
X
Process/
Temperature
Range
BLANK
I(1)
Commercial (0°C to +70°C)
Industrial (40°C to +85°C)
G
Green
PF
PQF
Thin Quad Flat Pack (TQFP, PN120-1)
Plastic Quad Flat Pack (PQFP, PQ132-1)
15
20
Commercial Only
Com'l & Ind'l
L
Low Power
723612
64 x 36 x 2 SyncBiFIFO™
Clock Cycle Time (tCLK)
Speed in Nanoseconds
3136 drw25
NOTES:
1. Industrial temperature range product for 20ns speed grade is available as a standard device. All other speed grades are available by special order.
2. Green parts are available. For specific speeds and packages contact your sales office.
DATASHEET DOCUMENT HISTORY
03/05/2002
06/09/2005
02/13/2009
pgs. 1, 8, 9 and 25.
pgs. 1, 2, 3 and 25.
pg. 25.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, Ca 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
25
for TECH SUPPORT:
408-360-1753
FIFOhelp@idt.com