IDT72V3641L15PF

3.3 VOLT CMOS SyncFIFOTM 512 x 36 1,024 x 36 FEATURES • • • • • • • • • • • • • Storage capacity: 72V3631 - 512 x 36 72V3641 - 1,024 x 36 Supports clock frequencies up to 67 MHz Fast access times of 10ns Free-running CLKA and CLKB can be asynchronous or coincident (permits simultaneous reading and writing of data on a single clock edge) Clocked FIFO buffering data from Port A to Port B Synchronous read retransmit capability Mailbox register in each direction Programmable Almost-Full and Almost-Empty flags Microprocessor interface control logic Input Ready (IR) and Almost-Full (AF) flags synchronized by CLKA Output Ready (OR) and Almost-Empty (AE) flags synchronized by CLKB • • 72V3631 72V3641 Available in space-saving 120-pin thin quad flat package (TQFP) Pin and functionally compatible versions of the 5V operating 723631/723641 Easily expandable in width and depth Green parts are available, see ordering information DESCRIPTION The 72V3631/72V3641 are pin and functionally compatible versons of the 723631/723641, designed to run off a 3.3V supply for exceptionally low-power consumption. These devices are monolithic high-speed, low-power, CMOS clocked FIFO memory. It supports clock frequencies up to 67 MHz and has read access times as fast as 10ns. The 512/1,024 x 36 dual-port SRAM FIFO buffers data from port A to Port B. The FIFO memory has retransmit capability, which allows previously read data to be accessed again. The FIFO operates in First Word Fall Through mode and has flags to indicate empty and full conditions and conditions and two programmable flags (Almost-Full and Almost-Empty) to indicate when a selected number of words is stored in memory. Communication FUNCTIONAL BLOCK DIAGRAM MBF1 RAM ARRAY 512 x 36 1,024 x 36 Reset Logic 36 Write Pointer A0 - A35 Read Pointer IR AF Status Flag Logic FS0/SD FS1/SE N Flag Offset Registers 10 Mail 2 Register Sync Retransmit Logic RST Input Register Port-A Control Logic Output Register Mail 1 Register CLKA CSA W/RA ENA MBA RTM RFM B0 - B35 OR AE Port-B Control Logic CLKB CSB W/RB ENB MBB 4658 drw 01 MBF2 COMMERCIAL TEMPERATURE RANGE 11 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE DESCRIPTION (CONTINUED) provide a simple interface between microprocessors and/or buses with synchronous control. The Input Ready (IR) flag and Almost-Full (AF) flag of the FIFO are two-stage synchronized to CLKA. The Output Ready (OR) flag and Almost-Empty (AE) flag of the FIFO are two-stage synchronized to CLKB. Offset values for the Almost-Full and Almost-Empty flags of the FIFO can be programmed from port A or through a serial input. The 72V3631/72V3641 are characterized for operation from 0°C to 70°C. These devices are fabricated using high speed, submicron CMOS technology. between each port may take place with two 36-bit mailbox registers. Each mailbox register has a flag to signal when new mail has been stored. Two or more devices may be used in parallel to create wider data paths. Expansion is also possible in word depth. These devices are a clocked FIFO, which means each port employs a synchronous interface. All data transfers through a port are gated to the LOWto-HIGH transition of a continuous (free-running) port clock by enable signals. The continuous clocks for each port are independent of one another and can be asynchronous or coincident. The enables for each port are arranged to 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 B35 B34 B33 B32 GND B31 B30 B29 B28 B27 B26 VCC B25 B24 GND B23 B22 B21 B20 B19 B18 GND B17 B16 VCC B15 B14 B13 B12 GND PIN CONFIGURATION 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 72V3631 72V3641 B11 B10 B9 B8 B7 VCC B6 GND B5 B4 B3 B2 B1 B0 GND GND A0 A1 A2 VCC A3 A4 A5 GND A6 A7 A8 A9 A10 A11 GND A35 A34 A33 A32 VCC A31 A30 GND A29 A28 A27 A26 A25 A24 A23 GND A22 VCC A21 A20 A19 A18 GND A17 A16 A15 A14 A13 VCC A12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 VCC CLKB ENB W/RB CSB GND MBF1 GND MBB NC VCC RFM RTM FS1/SEN FS0/SD GND RST MBA MBF2 VCC AE AF VCC OR IR CSA W/RA ENA CLKA GND TOP VIEW NOTE: 1. NC – No internal connection. Package Type Package Code Order Code TQFP PNG120 PF 2 Oct.29.21 4658 drw 03 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE PIN DESCRIPTION Symbol Name A0-A35 Port-A Data AE Almost-Empty Flag AF Almost-Full Flag B0-B35 Port-B Data CLKA Port-A Clock CLKB Port-B Clock CSA Port-A Chip CSB Port-B Chip ENA ENB FS1/ SEN, Port-A Enable Port-B Enable Flag-Offset Select 1/ Serial Enable Flag Offset 0/ Serial Data FS0/SD IR Input Ready Flag MBA Port-A Mailbox Select Port-B Mailbox Select Mail1 Register Flag Mail2 Register Flag Output Ready Flag MBB MBF1 MBF2 OR RFM RST Read From Mark Reset I/O Description I/O 36-bit bidirectional data port for side A. O Programmable flag synchronized to CLKB. It is LOW when the number of words in the FIFO is less than or equal to the value in the Almost-Empty register (X). O Programmable flag synchronized to CLKA. It is LOW when the number of empty locations in the FIFO is less than or equal to the value in the Almost-Full Offset register (Y). I/O 36-bit bidirectional data port for side B. I CLKA is a continuous clock that synchronizes all data transfers through port-A and may be asynchronous or coincident to CLKB. IR and AF are synchronous to the LOW-to-HIGH transition of CLKA. I CLKB is a continuous clock that synchronizes all data transfers through port-B and may be asynchronous or coincident to CLKA. OR and AE are synchronous to the LOW-to-HIGH transition of CLKB. I CSA must be LOW to enable a LOW-to-HIGH transition of CLKA to read or write data on port-A. The A0-A35 Select outputs are in the high-impedance state when CSA is HIGH. I CSB must be LOW to enable a LOW-to-HIGH transition of CLKB to read or write data on port-B. The B0-B35 Select outputs are in the high-impedance state when CSB is HIGH. I ENA must be HIGH to enable a LOW-to-HIGH transition of CLKA to read or write data on port-A. I ENB must be HIGH to enable a LOW-to-HIGH transition of CLKB to read or write data on port-B. I FS1/SEN and FS0/SD are dual-purpose inputs used for flag Offset register programming. During a device reset, FS1/SEN and FS0/SD selects the flag offset programming method. Three Offset register programming methods are available: automatically load one of two preset values, parallel load from port A, and serial load. When serial load is selected for flag Offset register programming, FS1/SEN is used as an enable synchronous to the LOW-to-HIGH transition of CLKA. When FS1/SEN is LOW, a rising edge on CLKA load the bit present on FS0/SD into the X and Y registers. The number of bit writes required to program the Offset registers is 18/20 for the 72V3631/72V3641 respectively. The first bit write stores the Y-register MSB and the last bit write stores the X-register LSB. O IR is synchronized to the LOW-to-HIGH transition of CLKA. When IR is LOW, the FIFO is full and writes to its array are disabled. When the FIFO is in retransmit mode, IR indicates when the memory has been filled to the point of the retransmit data and prevents further writes. IR is set LOW during reset and is set HIGH after reset. I A HIGH level chooses a mailbox register for a port-A read or write operation. I O O O I I RTM Retransmit Mode I W/RA Port-A Write/ Read Select I W/RB Port-B Write/ Read Select I A HIGH level chooses a mailbox register for a port-B read or write operation. When the B0-B35 outputs are active, a HIGH level on MBB selects data from the mail1 register for output and a LOW level selects FIFO data for output. MBF1 is set LOW by the LOW-to-HIGH transition of CLKA that writes data to the mail1 register. MBF1 is set HIGH by a LOW-to-HIGH transition of CLKB when a port-B read is selected and MBB is HIGH. MBF1 is set HIGH by a reset. MBF2 is set LOW by the LOW-to-HIGH transition of CLKB that writes data to the mail2 register. MBF2 is set HIGH by a LOW-to-HIGH transition of CLKA when a port-A read is selected and MBA is HIGH. MBF2 is set HIGH by a reset. OR is synchronized to the LOW-to-HIGH transition of CLKB. When OR is LOW, the FIFO is empty and reads are disabled. Ready data is present in the output register of the FIFO when OR is HIGH. OR is forced LOW during the reset and goes HIGH on the third LOW-to-HIGH transition of CLKB after a word is loaded to empty memory. When the FIFO is in retransmit mode, a HIGH on RFM enables a LOW-to-HIGH transition of CLKB to reset the read pointer to the beginning retransmit location and output the first selected retransmit data. To reset the device, four LOW-to-HIGH transitions of CLKA and four LOW-to-HIGH transitions of CLKB must occur while RST is LOW. The LOW-to-HIGH transition of RST latches the status of FS0 and FS1 for AF and AE offset selection. When RTM is HIGH and valid data is present in the FIFO output register (OR is HIGH), a LOW-to-HIGH transition of CLKB selects the data for the beginning of a retransmit and puts the FIFO in retransmit mode. The selected word remains the initial retransmit point until a LOW- to-HIGH transition of CLKB occurs while RTM is LOW, taking the FIFO out of retransmit mode. A HIGH selects a write operation and a LOW selects a read operation on port A for a LOW-to-HIGH transition of CLKA. The A0-A35 outputs are in the high-impedance state when W/RA is HIGH. A LOW selects a write operation and a HIGH selects a read operation on port B for a LOW-to-HIGH transition of CLKB. The B0-B35 outputs are in the high-impedance state when W/RB is LOW. 3 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS OVER OPERATING FREE-AIR TEMPERATURE RANGE (Unless otherwise noted)(2) Symbol Rating Commercial Unit V CC Supply Voltage Range VI Input Voltage Range –0.5 to VCC+0.5 Output Voltage Range –0.5 to VCC+0.5 V (2) VO (2) –0.5 to +4.6 V (3) V IIK Input Clamp Current, (VI < 0 or VI > VCC) ±20 mA IOK Output Clamp Current, (VO = < 0 or VO > VCC) ±50 mA I OUT Continuous Output Current, (VO = 0 to VCC) ±50 mA I CC Continuous Current Through VCC or GND ±400 mA T STG Storage Temperature Range –65 to 150 °C NOTES: 1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output voltage ratings may be exceeded provided the input and output current ratings are observed. 3. Control Inputs: maximum VI = 5.0V. RECOMMENDED OPERATING CONDITIONS Symbol VCC VIH VIL IOH IOL TA Parameter Supply Voltage HIGH Level Input Voltage LOW-Level Input Voltage HIGH-Level Output Current LOW-Level Output Current Operating Free-air Temperature Min. 3.0 2 — — — Typ. 3.3 — — — — Max. 3.6 VCC+0.5 0.8 –4 8 Unit V V V mA mA 0 — 70 °C ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING FREE-AIR TEMPERATURE RANGE (Unless otherwise noted) Symbol VOH VOL ILI ILO ICC2(2) CIN C OUT Parameter Output Logic "1" Voltage Output Logic "0" Voltage Input Leakage Current (Any Input) Output Leakage Current Standby Current Input Capacitance Output Capacitance VCC = 3.0V, VCC = 3.0V, VCC = 3.6V, VCC = 3.6V, VCC = 3.6V, VI = 0, VO = 0, Test Conditions IOH = –4 mA IOL = 8 mA VI = VCC or 0 VO = VCC or 0 VI = VCC –0.2V or 0 f = 1 MHz f = 1 MHZ NOTES: 1. All typical values are at VCC = 3.3V, TA = 25°C. 2. For additional ICC information, see Figure 1, Typical Characteristics: Supply Current (ICC) vs. Clock Frequency (fS). 4 Oct.29.21 Min. 2.4 — — — — — — 72V3631 72V3641 Commercial tCLK = 15 ns Typ.(1) — — — — — 4 8 Max. — 0.5 ±5 ±5 400 — — Unit V V µA µA µA pF pF 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE DETERMINING ACTIVE CURRENT CONSUMPTION AND POWER DISSIPATION The ICC(f) current for the graph in Figure 1 was taken while simultaneously reading and writing the FIFO on the 72V3641 with CLKA and CLKB set to fS. All data inputs and data outputs change state during each clock cycle to consume the highest supply current. Data outputs were disconnected to normalize the graph to a zero-capacitance load. Once the capacitance load per data-output channel and the number of 72V3631/72V3641 inputs driven by TTL HIGH levels are known, the power dissipation can be calculated with the equation below. CALCULATING POWER DISSIPATION With ICC(f) taken from Figure 1, the maximum power dissipation (PT) of these FIFOs may be calculated by: PT = VCC x ICC(f) + Σ(CL x VCC2 x fO) N where: N = number of outputs = 36 CL = output capacitance load fO = switching frequency of an output When no reads or writes are occurring on these devices, the power dissipated by a single clock (CLKA or CLKB) input running at frequency fS is calculated by: PT = VCC x fS x 0.025 mA/MHz 175 fdata = 1/2 fS TA = 25°C 150 VCC = 3.6V ICC(f) Supply Current mA CL = 0 pF VCC = 3.3V 125 VCC = 3.0V 100 75 50 25 0 0 10 20 30 fS 40 Clock Frequency 50 MHz Figure 1. Typical Characteristics: Supply Current (ICC) vs. Clock Frequency (fS) 5 Oct.29.21 60 70 4658 drw 04 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS OVER RECOMMENDED RANGES OF SUPPLY VOLTAGE AND OPERATING FREE-AIR TEMPERATURE 72V3631L15 72V3641L15 Symbol Parameter Min. Max. Unit fS Clock Frequency, CLKA or CLKB – 66.7 MHz tCLK Clock Cycle Time, CLKA or CLKB 15 – ns tCLKH Pulse Duration, CLKA or CLKB HIGH 6 – ns tCLKL Pulse Duration, CLKA or CLKB LOW 6 – ns tDS Setup Time, A0-A35 before CLKA↑ and B0-B35 before CLKB↑ 5 – ns tENS1 Setup Time, ENA to CLKA↑; ENB to CLKB↑ 5 – ns tENS2 Setup Time, CSA, W/RA, and MBA to CLKA↑; CSB, W/RB, and MBB to CLKB↑ 7 – ns tRMS Setup Time, RTM and RFM to CLKB↑ 6 – ns tRSTS Setup Time, RST LOW before CLKA↑ or CLKB↑ 5 – ns tFSS Setup Time, FS0 and FS1 before RST HIGH 9 – ns Setup Time, FS0/SD before CLKA↑ 5 – ns Setup Time, FS1/SEN before CLKA↑ 5 – ns tSDS (2) tSENS (2) (1) tDH Hold Time, A0-A35 after CLKA↑ and B0-B35 after CLKB↑ 0.5 – ns tENH1 Hold Time, ENA after CLKA↑; ENB after CLKB↑ 0.5 – ns tENH2 Hold Time, CSA, W/RA, and MBA after CLKA↑; CSB, W/RB, and MBB after CLKB↑ 0.5 – ns tRMH Hold Time, RTM and RFM after CLKB↑ 0.5 – ns tRSTH Hold Time, RST LOW after CLKA↑ or CLKB↑ 5 – ns tFSH Hold Time, FS0 and FS1 after RST HIGH 0 – ns Hold Time, FS1/SEN HIGH after RST HIGH 0 – ns Hold Time, FS0/SD after CLKA↑ 0 – ns Hold Time, FS1/SEN after CLKA↑ 0 – ns Skew Time, between CLKA↑ and CLKB↑ for OR and IR 9 – ns Skew Time, between CLKA↑ and CLKB↑ for AE and AF 12 – ns tSPH (2) tSDH (2) tSENH (2) tSKEW1 (3) tSKEW2 (3,4) (1) NOTES: 1. Requirement to count the clock edge as one of at least four needed to reset a FIFO. 2. Only applies when serial load method is used to program flag Offset registers. 3. Skew time is not a timing constraint for proper device operation and is only included to illustrate the timing relationship between CLKA cycle and CLKB cycle. 4. Design simulated, not tested. 6 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS 72V3631L15 72V3641L15 Symbol Parameter Min. Max. Unit fS Clock Frequency, CLKA or CLKB – 66.7 MHz tA Access Time, CLKB↑ to B0-B35 2 10 ns tPIR Propagation Delay Time, CLKA↑ to IR 1 8 ns tPOR Propagation Delay Time, CLKB↑ to OR 1 8 ns tPAE Propagation Delay Time, CLKB↑ to AE 1 8 ns tPAF Propagation Delay Time, CLKA↑ to AF 1 8 ns tPMF Propagation Delay Time, CLKA↑ to MBF1 LOW or MBF2 HIGH and CLKB↑ to MBF2 LOW or MBF1 HIGH 0 8 ns tPMR Propagation Delay Time, CLKA↑ to B0-B35(1) and CLKB↑ to A0-A35(2) 2 10 ns tMDV Propagation Delay Time, MBB to B0-B35 Valid 2 10 ns tRSF Propagation Delay Time, RST LOW to AE LOW and AF HIGH 1 15 ns tEN Enable Time, CSA and W/RA LOW to A0-A35 Active and CSB LOW and W/RB HIGH to B0-B35 Active 2 10 ns tDIS Disable Time, CSA or W/RA HIGH to A0-A35 at high impedance and CSB HIGH or W/RB LOW to B0-B35 at high impedance 1 8 ns NOTES: 1. Writing data to the mail1 register when the B0-B35 outputs are active and MBB is HIGH. 2. Writing data to the mail2 register when the A0-A35 outputs are active and MBA is HIGH. 7 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE SIGNAL DESCRIPTION is complete, the X and Y register values are loaded bitwise through the FS0/ SD input on each LOW-to-HIGH transition of CLKA that the FS1/SEN input is LOW. There are 18- or 20-bit writes needed to complete the programming for the 72V3631 or 72V3641 respectively. The first-bit write stores the most significant bit of the Y register, and the last-bit write stores the least significant bit of the X register. Each register value can be programmed from 1 to 508 (72V3631) or 1 to 1,020 (72V3641). When the option to program the Offset registers serially is chosen, the Input Ready (IR) flag remains LOW until all register bits are written. The IR flag is set HIGH by the LOW-to-HIGH transition of CLKA after the last bit is loaded to allow normal FIFO operation. The timing diagram for serial load of offset registers can be found in Figure 4. RESET The 72V3631/72V3641 is reset by taking the Reset (RST) input LOW for at least four port-A Clock (CLKA) and four port-B (CLKB) LOW-to-HIGH transitions. The Reset input may switch asynchronously to the clocks. A reset initializes the memory read and write pointers and forces the Input Ready (IR) flag LOW, the Output Ready (OR) flag LOW, the Almost-Empty (AE) flag LOW, and the Almost-Full (AF) flag HIGH. Resetting the device also forces the Mailbox Flags (MBF1, MBF2) HIGH. After a FIFO is reset, its Input Ready flag is set HIGH after at least two clock cycles to begin normal operation. A FIFO must be reset after power up before data is written to its memory. The relevant FIFO Reset timing diagram can be found in Figure 2. FIFO WRITE/READ OPERATION The state of the port-A data (A0-A35) outputs is controlled by the port-A Chip Select (CSA) and the port-A Write/Read select (W/RA). The A0-A35 outputs are in the high-impedance state when either CSA or W/RA is HIGH. The A0A35 outputs are active when both CSA and W/RA are LOW. Data is loaded into the FIFO from the A0-A35 inputs on a LOW-to-HIGH transition of CLKA when CSA and the port-A Mailbox select (MBA) are LOW, W/RA, the port-A Enable (ENA), and the Input Ready (IR) flag are HIGH (see Table 2). Writes to the FIFO are independent of any concurrent FIFO read. For the Write Cycle Timing diagram, see Figure 5. The port-B control signals are identical to those of port-A with the exception that the port-B Write/Read select (W/RB) is the inverse of the port-A Write/Read select (W/RA). The state of the port-B data (B0-B35) outputs is controlled by the port-B Chip Select (CSB) and the port-B Write/Read select (W/RB). The B0-B35 outputs are in the high-impedance state when either CSB is HIGH or W/RB is LOW. The B0-B35 outputs are active when CSB is LOW and W/RB is HIGH. Data is read from the FIFO to its output register on a LOW-to-HIGH transition of CLKB when CSB and the port-B Mailbox select (MBB) are LOW, W/RB, the port-B Enable (ENB), and the Output Ready (OR) flag are HIGH (see Table 3). Reads from the FIFO are independent of any concurrent FIFO writes. For the Read Cycle Timing diagram, see Figure 6. The setup- and hold-time constraints to the port clocks for the port Chip Selects and Write/Read selects are only for enabling write and read operations and are not related to high-impedance control of the data outputs. If a port Enable is LOW during a clock cycle, the port Chip Select and Write/Read select may change states during the setup- and hold time window of the cycle. When the OR flag is LOW, the next data word is sent to the FIFO output register automatically by the CLKB LOW-to-HIGH transition that sets the OR flag HIGH. When OR is HIGH, an available data word is clocked to the FIFO output register only when a FIFO read is selected by the port-B Chip Select (CSB), Write/Read select (W/RB), Enable (ENB), and Mailbox select (MBB). FIRST WORD FALL THROUGH MODE (FWFT) These devices operate in the First Word Fall Through mode (FWFT). This mode uses the Output Ready function (OR) to indicate whether or not there is valid data at the data outputs (B0-B35). It also uses the Input Ready (IR) function to indicate whether or not the FIFO memory has any free space for writing. In the FWFT mode, the first word written to an empty FIFO goes directly to data outputs, no read request necessary. Subsequent words must be accessed by performing a formal read operation. ALMOST-EMPTY FLAG AND ALMOST-FULL FLAG OFFSET PROGRAMMING Two registers in these devices are used to hold the offset values for the AlmostEmpty and Almost-Full flags. The Almost-Empty (AE) flag Offset register is labeled X, and the Almost-Full (AF) flag Offset register is labeled Y. The Offset register can be loaded with a value in three ways: one of two preset values are loaded into the Offset registers, parallel load from port A, or serial load. The Offset register programming mode is chosen by the flag select (FS1, FS0) inputs during a LOW-to-HIGH transition on the RST input (See Table 1). — PRESET VALUES If the preset value of 8 or 64 is chosen by the FS1 and FS0 inputs at the time of a RST LOW-to-HIGH transition according to Table 1, the preset value is automatically loaded into the X and Y registers. No other device initialization is necessary to begin normal operation, and the IR flag is set HIGH after two LOWto-HIGH transitions on CLKA. For the Preset value loading timing diagram, see Figure 2. — PARALLEL LOAD FROM PORT A To program the X and Y registers from port A, the device is reset with FS0 and FS1 LOW during the LOW-to-HIGH transition of RST. After this reset is complete, the IR flag is set HIGH after two LOW-to-HIGH transitions on CLKA. The first two writes to the FIFO do not store data in its memory but load the Offset registers in the order Y, X. Each Offset register of the 72V3631 and 72V3641 uses port-A inputs (A8-A0), (A9-A0), and (A10-A0), respectively. The highest number input is used as the most significant bit of the binary number in each case. Each register value can be programmed from 1 to 508 (72V3631) and 1 to 1,020 (72V3641). After both Offset registers are programmed from port A, subsequent FIFO writes store data in the RAM. The timing diagram for parallel load of offset registers can be found in Figure 3. TABLE 1 — FLAG PROGRAMMING — SERIAL LOAD To program the X and Y registers serially, the device is reset with FS0/SD and FS1/SEN HIGH during the LOW-to-HIGH transition of RST. After this reset FS0 RST X and Y Registers (1) H H ↑ Serial Load H L ↑ 64 L H ↑ 8 L L ↑ Parallel Load From Port A NOTE: 1. X register holds the offset for AE; Y register holds the offset for AF. 8 Oct.29.21 FS1 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE SYNCHRONIZED FIFO FLAGS Each 72V3631/72V3641 FIFO flag is synchronized to its port Clock through at least two flip-flop stages. This is done to improve the flags’ reliability by reducing the probability of metastable events on their outputs when CLKA and CLKB operate asynchronously to one another. OR and AE are synchronized to CLKB. IR and AF are synchronized to CLKA. Table 4 shows the relationship of each flag to the number of words stored in memory. INPUT READY FLAG (IR) The Input Ready flag of a FIFO is synchronized to the port Clock that writes data to its array (CLKA). When the IR flag is HIGH, a memory location is free in the FIFO to write new data. No memory locations are free when the IR flag is LOW and attempted writes to the FIFO are ignored. Each time a word is written to a FIFO, its write pointer is incremented. The state machine that controls an IR flag monitors a write-pointer and read pointer comparator that indicates when the FIFO memory status is full, full-1, or full-2. From the time a word is read from a FIFO, its previous memory location is ready to be written in a minimum of three cycles of CLKA. Therefore, an IR flag is LOW if less than two cycles of CLKA have elapsed since the next memory write location has been read. The second LOW-to-HIGH transition on CLKA after the read sets the Input Ready flag HIGH, and data can be written in the following cycle. A LOW-to-HIGH transition on CLKA begins the first synchronization cycle of a read if the clock transition occurs at time tSKEW1 or greater after the read. Otherwise, the subsequent CLKA cycle may be the first synchronization cycle (see Figure 8). OUTPUT READY FLAG (OR) The Output Ready flag of a FIFO is synchronized to the port Clock that reads data from its array (CLKB). When the OR flag is HIGH, new data is present in the FIFO output register. When the OR flag is LOW, the previous data word is present in the FIFO output register and attempted FIFO reads are ignored. A FIFO read pointer is incremented each time a new word is clocked to its output register. The state machine that controls an OR flag monitors a writepointer and read-pointer comparator that indicates when the FIFO memory status is empty, empty+1, or empty+2. From the time a word is written to a FIFO, it can be shifted to the FIFO output register in a minimum of three cycles of CLKB. Therefore, an OR flag is LOW if a word in memory is the next data to be sent to the FIFO output register and three CLKB cycles have not elapsed since the time the word was written. The OR flag of the FIFO remains LOW until the third LOW-to-HIGH transition of CLKB occurs, simultaneously forcing the OR flag HIGH and shifting the word to the FIFO output register. A LOW-to-HIGH transition on CLKB begins the first synchronization cycle of a write if the clock transition occurs at time tSKEW1 or greater after the write. Otherwise, the subsequent CLKB cycle may be the first synchronization cycle (see Figure 7). ALMOST-EMPTY FLAG (AE) The Almost-Empty flag of a FIFO is synchronized to the port Clock that reads data from its array (CLKB). The state machine that controls an AE flag monitors a write-pointer and read-pointer comparator that indicates when the FIFO memory status is almost-empty, almost-empty+1, or almost-empty+2. The almost-empty state is defined by the contents of register X. This register is loaded with a preset value during a FIFO reset, programmed from port A, or programmed serially (see Almost-Empty flag and Almost-Full flag offset pro- TABLE 2 — PORT-A ENABLE FUNCTION TABLE CSA W/RA ENA MBA CLKA Data A (A0-A35) I/O Port Functions H X X X X Input None L H L X X Input None L H H L ↑ Input FIFO Write L H H H ↑ Input Mail1 Write L L L L X Output None L L H L ↑ Output None L L L H X Output None L L H H ↑ Output Mail2 Read (Set MBF2 HIGH) TABLE 3 — PORT-B ENABLE FUNCTION TABLE CSB W/RB ENB MBB CLKB Data B (B0-A35) I/O Port Functions H X X X X Input None L L L X X Input None L L H L ↑ Input None L L H H ↑ Input Mail2 Write L H L L X Output None L H H L ↑ Output FIFO read L H L H X Output None L H H H ↑ Output Mail1 Read (Set MBF1 HIGH) 9 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE gramming section). The AE flag is LOW when the FIFO contains X or less words and is HIGH when the FIFO contains (X+1) or more words. A data word present in the FIFO output register has been read from memory. Two LOW-to-HIGH transitions of CLKB are required after a FIFO write for the AE flag to reflect the new level of fill; therefore, the AE flag of a FIFO containing (X+1) or more words remains LOW if two cycles of CLKB have not elapsed since the write that filled the memory to the (X+1) level. An AE flag is set HIGH by the second LOW-to-HIGH transition of CLKB after the FIFO write that fills memory to the (X+1) level. A LOW-to-HIGH transition of CLKB begins the first synchronization cycle if it occurs at time tSKEW2 or greater after the write that fills the FIFO to (X+1) words. Otherwise, the subsequent CLKB cycle may be the first synchronization cycle (see Figure 9). The synchronous retransmit feature of these devices allow FIFO data to be read repeatedly starting at a user-selected position. The FIFO is first put into retransmit mode to select a beginning word and prevent ongoing FIFO write operations from destroying retransmit data. Data vectors with a minimum length of three words can retransmit repeatedly starting at the selected word. The FIFO can be taken out of retransmit mode at any time and allow normal device operation. The FIFO is put in retransmit mode by a LOW-to-HIGH transition on CLKB when the retransmit mode (RTM) input is HIGH and OR is HIGH. The rising CLKB edge marks the data present in the FIFO output register as the first retransmit data. The FIFO remains in retransmit mode until a LOW-to-HIGH transition occurs while RTM is LOW. When two or more reads have been done past the initial marked retransmit word, a retransmit is initiated by a LOW-to-HIGH transition on CLKB when the read-from-mark (RFM) input is HIGH. This rising CLKB edge shifts the first retransmit word to the FIFO output register and subsequent reads can begin immediately. Retransmit loops can be done endlessly while the FIFO is in retransmit mode. RFM must be LOW during the CLKB rising edge that takes the FIFO out of retransmit mode (see Figure 11). When the FIFO is put into retransmit mode, it operates with two read pointers. The current read pointer operates normally, incrementing each time when a new word is shifted to the FIFO output register. This read pointer position is used by the OR and AE flags. The shadow read pointer stores the memory location at the time the device is put into retransmit mode and does not change until the device is taken out of retransmit mode. The shadow read pointer position is used by the IR and AF flags. Data writes can proceed while the FIFO is in retransmit mode, but AF is set LOW by the write that stores (512-Y) or (1,024-Y) words after the first retransmit word for the 72V3631 or 72V3641 respectively. The IR flag is set LOW by the 512th or 1,024th write after the first retransmit word for the 72V3631 or 72V3641 respectively. When the FIFO is in retransmit mode and RFM is HIGH, a rising CLKB edge loads the current read pointer with the shadow read-pointer value and the OR flag reflects the new level of fill immediately. If the retransmit changes the FIFO status out of the almost-empty range, up to two CLKB rising edges after the retransmit cycle are needed to switch AE high (see Figure 12). The rising CLKB edge that takes the FIFO out of retransmit mode shifts the read pointer used by the IR and AF flags from the shadow to the current read pointer. If the change ALMOST-FULL FLAG (AF) The Almost-Full flag of a FIFO is synchronized to the port Clock that writes data to its array (CLKA). The state machine that controls an AF flag monitors a write-pointer and read-pointer comparator that indicates when the FIFO memory status is almost-full, almost-full-1, or almost-full-2. The almost-full state is defined by the contents of register Y. This register is loaded with a preset value during a FIFO reset, programmed from port A, or programmed serially (see Almost-Empty flag and Almost-Full flag offset programming section). The AF flag is LOW when the number of words in the FIFO is greater than or equal to (512-Y) or (1,024-Y) for the 72V3631 or 72V3641 respectively. The AF flag is HIGH when the number of words in the FIFO is less than or equal to [512-(Y+1)] or [1,024-(Y+1)] for the 72V3631 or 72V3641 respectively. A data word present in the FIFO output register has been read from memory. Two LOW-to-HIGH transitions of CLKA are required after a FIFO read for its AF flag to reflect the new level of fill. Therefore, the AF flag of a FIFO containing [512/1,024-(Y+1)] or less words remains LOW if two cycles of CLKA have not elapsed since the read that reduced the number of words in memory to [512/ 1,024-(Y+1)]. An AF flag is set HIGH by the second LOW-to-HIGH transition of CLKA after the FIFO read that reduces the number of words in memory to [512/1,024-(Y+1)]. A LOW-to-HIGH transition of CLKA begins the first synchronization cycle if it occurs at time tSKEW2 or greater after the read that reduces the number of words in memory to [512/1,024-(Y+1)]. Otherwise, the subsequent CLKA cycle may be the first synchronization cycle (see Figure 10). SYNCHRONOUS RETRANSMIT TABLE 4 — FIFO FLAG OPERATION Number of Words in the FIFO(1,2) Synchronized to CLKB Synchronized to CLKA 72V3631(3) 72V3641(3) OR AE AF IR 0 0 L L H H 1 to X 1 to X H L H H (X+1) to [512-(Y+1)] (X+1) to [1,024-(Y+1)] H H H H (512-Y) to 511 (1,024-Y) to 1,023 H H L H 512 1,024 H H L L NOTES: 1. When a word is present in the FIFO output register, its previous memory location is free. 2. Data in the output register does not count as a "word i n FIFO memory". Since in FWFT mode, the first words written to an empty FIFO goes unrequested to the output register (no read operation necessary), it is not included in the memory count. 3. X is the Almost-Empty Offset for AE. Y is the Almost-Full Offset for AF. 10 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE of read pointer used by IR and AF should cause one or both flags to transmit HIGH, at least two CLKA synchronizing cycles are needed before the flags reflect the change. A rising CLKA edge after the FIFO is taken out of retransmit mode is the first synchronizing cycle of IR if it occurs at time tSKEW1 or greater after the rising CLKB edge (see Figure 13). A rising CLKA edge after the FIFO is taken out of retransmit mode is the first synchronizing cycle of AF if it occurs at time tSKEW2 or greater after the rising CLKB edge (see Figure 14). register when a port-B Write is selected by CSB, W/RB, and ENB with MBB HIGH. Writing data to a mail register sets its corresponding flag (MBF1 or MBF2) LOW. Attempted writes to a mail register are ignored while its mail flag is LOW. When the port-B data (B0-B35) outputs are active, the data on the bus comes from the FIFO output register when the port-B Mailbox select (MBB) input is LOW and from the Mail1 register when MBB is HIGH. Mail2 data is always present on the port-A data (A0-A35) outputs when they are active. The Mail1 register Flag (MBF1) is set HIGH by a LOW-to-HIGH transition on CLKB when a portB Read is selected by CSB, W/RB, and ENB with MBB HIGH. The Mail2 register Flag (MBF2) is set HIGH by a LOW-to-HIGH transition on CLKA when a portA Read is selected by CSA, W/RA, and ENA with MBA HIGH. The data in a mail register remains intact after it is read and changes only when new data is written to the register. Mail Register and Mail Register Flag timing can be found in Figure 15 and 16. MAILBOX REGISTERS Two 36-bit bypass registers are on the 72V3631/72V3641 to pass command and control information between port A and port B. The Mailbox select (MBA, MBB) inputs choose between a mail register and a FIFO for a port data transfer operation. A LOW-to-HIGH transition on CLKA writes A0-A35 data to the mail1 register when a port-A Write is selected by CSA, W/RA, and ENA with MBA HIGH. A LOW-to-HIGH transition on CLKB writes B0-B35 data to the mail2 11 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE CLKA tRSTH CLKB tFSS tRSTS tFSH RST 0,1 FS1,FS0 tPIR tPIR IR tPOR OR tRSF AE tRSF AF tRSF MBF1, MBF2 4658 drw 05 Figure 2. FIFO Reset and Loading X and Y with a Preset Value of Eight CLKA RST tFSS tFSH FS1,FS0 tPIR IR tENS1 tENH1 ENA tDS tDH A0 - A35 AF Offset (Y) AE Offset (X) First Word Stored in FIFO 4658 drw06 NOTE: 1. CSA = LOW, W/RA = HIGH, MBA = LOW. It is not necessary to program Offset register on consecutive clock cycles. Figure 3. Programming the Almost-Full Flag and Almost-Empty Flag Offset Values from Port A 12 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE CLKA RST tPIR IR tFSS tSPH tSENS tSENH tSENS tSENH tSDS tSDH tSDS tSDH FS1/SEN tFSH tFSS FS0/SD AF Offset (Y) MSB 4658 drw07 AE Offset (X) LSB NOTE: 1. It is not necessary to program Offset register bits on consecutive clock cycles. FIFO write attempts are ignored until IR is set HIGH. Figure 4. Programming the Almost-Full Flag and Almost-Empty Flag Offset Values Serially tCLK tCLKH tCLKL CLKA IR HIGH tENS2 tENH2 tENS2 tENH2 tENS2 tENH2 tENS1 tENH1 CSA W/RA MBA tENS1 tENH1 tENS1 tENH1 ENA tDH tDS A0 - A35 W1 No Operation W2 4658 drw 08 Figure 5. FIFO Write Cycle Timing tCLK tCLKH tCLKL CLKB OR HIGH CSB W/RB MBB tENH1 tENS1 tENS1 tENH1 tENS1 tENH1 ENB B0 - B35 tEN tA tMDV tA W2 W1 No Operation tDIS W3 4658 drw 09 Figure 6. FIFO Read Cycle Timing 13 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE tCLKH tCLK tCLKL CLKA CSA LOW W/RA HIGH tENS2 tENH2 MBA tENS1 tENH1 ENA IR HIGH tDH tDS A0 - A35 W1 tSKEW1 CLKB (1) tCLKH 1 tCLK tCLKL 2 3 tPOR tPOR OR FIFO Empty CSB LOW W/RB HIGH MBB LOW tENS1 tENH1 ENB tA B0 -B35 Old Data in FIFO Output Register W1 4658 drw 10 NOTE: 1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for OR to transition HIGH and to clock the next word to the FIFO output register in three CLKB cycles. If the time between the rising CLKA edge and rising CLKB edge is less than tSKEW1, then the transition of OR HIGH and the first word load to the output register may occur one CLKB cycle later than shown. Figure 7. OR Flag Timing and First Data Word Fall Through when the FIFO is Empty 14 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE tCLK tCLKH tCLKL CLKB CSB LOW W/RB HIGH MBB LOW tENS1 tENH1 ENB OR HIGH tA B0 - B35 Previous Word in FIFO Output Register Next Word From FIFO tSKEW1(1) tCLK tCLKH tCLKL 1 CLKA 2 tPIR tPIR IR FIFO Full CSA LOW W/RA HIGH tENH2 tENS2 MBA tENS1 tENH1 ENA tDS tDH Write A0 - A35 4658 drw 11 NOTE: 1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for IR to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising CLKA edge is less than tSKEW1, then IR may transition HIGH one CLKA cycle later than shown. Figure 8. IR Flag Timing and First Available Write when the FIFO is Full CLKA tENS1 tENH1 ENA tSKEW2 CLKB (1) 1 2 tPAE tPAE AE X Word in FIFO (X+1) Words in FIFO tENS1 tENH1 ENB 4658 drw 12 NOTES: 1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AE to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising CLKB edge is less than tSKEW2, then AE may transition HIGH one CLKB cycle later than shown. 2. FIFO write (CSA = LOW, W/RA = HIGH, MBA = LOW), FIFO read (CSB = LOW, W/RB = HIGH, MBB = LOW). Figure 9. Timing for AE when FIFO is Almost-Empty 15 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE tSKEW2 (1) 1 CLKA 2 tENH1 tENS1 ENA tPAF tPAF (2) (2) AF (Depth -Y) Words in FIFO [Depth -(Y+1)] Words in FIFO CLKB tENS1 tENH1 ENB 4658 drw 13 NOTES: 1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AF to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising CLKA edge is less than tSKEW2, then AF may transition HIGH one CLKA cycle later than shown. 2. Depth is 512 for the 72V3631 and 1,024 for the 72V3641. 3. FIFO write (CSA = LOW, W/RA = HIGH, MBA = LOW), FIFO read (CSB = LOW, W/RB = HIGH, MBB = LOW). Figure 10. Timing for AF when FIFO is Almost-Full CLKB tENS1 tENH1 tRMS tRMH ENB tRMS tRMH RTM tRMS tRMH RFM OR HIGH tA W0 Initiate Retransmit Mode with W0 as First Word B0-B35 tA tA W1 tA W2 Retransmit from Selected Position W0 End Retransmit Mode W1 4658 drw 14 NOTE: 1. CSB = LOW, W/RB = HIGH, MBB = LOW. No input enables other than RTM and RFM are needed to control retransmit mode or begin a retransmit. Other enables are shown only to relate retransmit operations to the FIFO output register. Figure 11. Retransmit Timing Showing Minimum Retransmit Length 1 CLKB RTM 2 HIGH tRMS tRMH RFM tPAE AE X or fewer words from Empty (X+1) or more words from Empty NOTE: 1. X is the value loaded in the Almost-Empty flag Offset register. Figure 12. AE Maximum Latency When Retransmit Increases the Number of Stored Words Above X. 16 Oct.29.21 4658 drw 15 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE tSKEW1 (1) CLKA 1 2 tPIR FIFO Filled to First Restransmit Word IR One or More Write Locations Available CLKB tRMS tRMH RTM 4658 drw 16 NOTE: 1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for IR to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising CLKA edge is less than tSKEW1, then IR may transition HIGH one CLKA cycle later than shown. Figure 13. IR Timing from the End of Retransmit Mode when One or More Write Locations are Available (1) tSKEW2 CLKA 1 AF 2 tPAE (Depth (2) -Y) or More Words Past First Restransmit Word (Y+1) or More Write Locations Available CLKB tRMH tRMS RTM 4658 drw 17 NOTES: 1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AF to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising CLKA edge is less than tSKEW2, then AF may transition HIGH one CLKA cycle later than shown. 2. Depth is 512 for the 72V3631 and 1,024 for the 72V3641. 3. Y is the value loaded in the Almost-Full flag Offset register. Figure 14. AF Timing from the End of Retransmit Mode when (Y+1) or More Write Locations are Available CLKA tENS2 tENH2 tENS2 tENH2 tENS2 tENH2 tENS2 tENH2 CSA W/RA MBA ENA tDS W1 A0 - A35 tDH CLKB tPMF tPMF MBF1 CSB W/RB MBB tENS1 tENH1 ENB tEN B0 - B35 tMDV FIFO Output Register tPMR tDIS W1 (Remains valid in Mail1 Register after read) 4658 drw 18 Figure 15. Timing for Mail1 Register and MBF1 Flag 17 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE CLKB tENS2 tENH2 tENS2 tENH2 tENS2 tENH2 tENS2 tENH2 CSB W/RB MBB ENB tDS W1 B0 - B35 tDH CLKA tPMF tPMF MBF2 CSA W/RA MBA tENS1 tENH1 ENA tEN tPMR tDIS A0 - A35 W1 (Remains valid in Mail2 Register after read) 4658 drw 19 Figure 16. Timing for Mail2 Register and MBF2 Flag TRANSFER CLOCK WRITE READ WRITE CLOCK (CLKA) CHIP SELECT (CSA) VCC CLKA CLKB OR READ CLOCK (CLKB) CHIP SELECT (CSB) ENA WRITE SELECT (W/RA) OUTPUT READY (OR) WRITE ENABLE (ENA) ALMOST-FULL FLAG (AF) A0-A35 n 72V3631 72V3641 ENB IR CSB CSA MBB MBA READ ENABLE (ENB) 72V3631 72V3641 READ SELECT (W/RB) VCC ALMOST-EMPTY FLAG (AE) DATA IN (Dn) B0-B35 INPUT READY (IR) MBA A0-A35 n Qn W/RB n DATA OUT (Qn) Dn VCC VCC W/RA B0-B35 MBB 4658 drw 20 NOTES: 1. Mailbox feature is not supported in depth expansion applications. (MBA + MBB tie to GND) 2. Transfer clock should be set either to the Write Port Clock (CLKA) or the Read Port Clock (CLKB), whichever is faster. 3. Retransmit feature is not supported in depth expansion applications. 4. The amount of time it takes for OR of the last FIFO in the chain to go HIGH (i.e. valid data to appear on the last FIFO’s outputs) after a word has been written to the first FIFO is the sum of the delays for each individual FIFO: (N - 1)*(4*transfer clock) + 3*TRCLK, where N is the number of FIFOs in the expansion and TRCLK is the CLKB period. 5. The amount of time is takes for IR of the first FIFO in the chain to go HIGH after a word has been read from the last FIFO is the sum of the delays for each individual FIFO: (N 1)*(3*transfer clock) + 2*TWCLK, where N is the number of FIFOs in the expansion and TWCLK is the CLKA period. Figure 17. Block Diagram of 512 x 36, 1,024 x 36 Synchronous FIFO Memory with Programmable Flags used in Depth Expansion Configuration 18 Oct.29.21 72V3631/72V3641 3.3V CMOS SYNCFIFO™ 512 x 36 and 1,024 x 36 COMMERCIAL TEMPERATURE RANGE PARAMETER MEASUREMENT INFORMATION 3.3V 330 Ω From Output Under Test 30 pF 510 Ω (1) 3V Timing Input 1.5 V GND tS th 3V Low-Level Input GND VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 1.5 V GND VOLTAGE WAVEFORMS PULSE DURATIONS 3V Output Enable 1.5 V tPLZ 1.5 V tPZL GND ¯ 3V Input 1.5 V Low-Level Output VOL tPZH VOH 1.5 V tPHZ 3V 1.5 V 1.5 V tPD tPD GND VOH In-Phase Output 1.5 V 1.5 V ¯ OV VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTE: 1. Includes probe and jig capacitance Figure 18. Load Circuit and Voltage Waveforms 19 Oct.29.21 GND tW 1.5 V 1.5 V 1.5 V 1.5 V 3V Data, Enable Input High-Level Output 3V High-Level Input VOL 4658 drw 21 ORDERING INFORMATION XXXXXX Device Type X XX X XX Power Speed Package X X Process/ Temperature Range Blank 8 Tray Tape and Reel BLANK Commercial (0°C to +70°C) G Green PF Thin Quad Flat Pack (PNG120) 15 Commercial Only L Low Power 72V3631 72V3641 512 x 36 3.3V SyncFIFO 1,024 x 36 3.3V SyncFIFO Clock Cycle Time (tCLK) Speed in Nanoseconds 4658 drw22 Orderable Part Information Pkg. Code Pkg. Type Temp. Grade Speed (ns) 72V3631L15PFG PNG120 TQFP C 15 72V3631L15PFG8 PNG120 TQFP C Speed (ns) 15 Orderable Part ID DATASHEET DOCUMENT HISTORY 07/31/2000 11/04/2003 02/05/2009 06/18/2014 10/29/2021 pgs. pg. pgs. pgs. pgs. 1, 14, 21. 1. 1 and 21. 1-20. 1-20. 20 Oct.29.21 Pkg. Code Pkg. Type Temp. Grade 72V3641L15PFG PNG120 TQFP C 72V3641L15PFG8 PNG120 TQFP C Orderable Part ID IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.