IDT79RC32V364-100DAG

79RC32364™ RISControllerTM Embedded 32-bit Microprocessor, based on RISCore32300 Features Flexible RC4000 compatible MMU with 32-page TLB on-chip – Variable page size – Variable number of locked entries – No performance penalty for address translation ◆ Flexible bus interface allows simple, low-cost designs – Bus interface runs at a fraction of pipeline rate – Programmable port-width interface (8-,16-, 32-bit memory and I/O regions) – Programmable bus turnaround times (BTA) – Supports single data or burst transactions ◆ Improved real-time support – Fast interrupt decode ◆ Low-power operation – Active power management: powers down inactive units – Typical power 700mW @ 133MHz – Stand-by mode VCC 3. Not more than one output should be shorted at a time. Duration of the short should not exceed 30 seconds. Recommended Operation Temperature and Supply Voltage Voltage Grade Temperature Gnd RC32364 VCC Core & Vcc I/O Commercial 0°C to +85°C (Case) 0V 3.3V±5% Industrial -40°C + 85°C (Case) 0V 3.3V±5% AC Electrical Characteristics — Commercial/Industrial Temperature Ranges—RC32364 VCC Core & VCC I/O = 3.3V ± 5%; TCase = 0°C to +85°C Commercial, TCase = -40° C to +85°C Industrial Clock Parameters—RC32364 Note: Operation of the RC32364 is only guaranteed with the Phase Lock Loop enabled Parameter Symbol Pipeline clock frequency Test Conditions PClk RC32364 100MHz RC32364 133MHz Min Max Min Max 80 100 80 133 MHz Units MasterClock HIGH tMCHIGH Transition ≤ 2ns 6 — 5 — ns MasterClock LOW tMCLOW Transition ≤ 2ns 6 — 5 — ns MasterClock Frequency — — 10 50 10 67 MHz tMCP — 20 100 15 100 ns tJitterIn1 — — ±250 — ±250 ps MasterClock Period 1 Clock Jitter for MasterClock 2 MasterClock Rise Time tMCRise — — 3 — 3 ns MasterClock Fall Time2 tMCFall — — 3 — 3 ns JTAG Clock Period tTCK — 100 — 100 — ns JTAG Clock High and Low Time tTCKLOW, tTCKHIGH — 40 — 40 — ns JTAG Clock Fall and Rise Time tTCKFall, tTCKRise — — 3 — 3 ns 1. Guaranteed by design 2. Rise and Fall times are measured between 10% and 90%. 12 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ System Interface Parameters—RC32364 Parameter Symbol Test Conditions RC32364 100MHz RC32364 133MHz Min Max Min Max Units Data Output tDO = Max — 6 — 6 ns Data Output Hold tDOH 0.7 — 0.7 — ns Data Output for ALE tDOA — 6 — 6 ns Data Setup tDS 3 — 3 — ns 6 — 5 — ns trise = 2ns tfall = 2ns Data Setup Special: Ack, Retry, BusErr tDSS Data Hold tDH 0.5 — 0.5 — ns JTAG Clock Period tTCK, t3 100 — 100 — ns DCLK Clock Period tDCK, t11 12.5 — 12.5 — ns DCLK High, Low Time tDCK High, t9 tDCK Low, t10 2.5 — 2.5 — ns DCLK Rise, Fall Time tDCK Rise, t15 tDCK Fall, t15 — 3.5 — 3.5 ns TDO Output Delay Time tTDODO, t4 — 6 — 6 ns TDI Input Setup Time tTDIS, t5 4 — 4 — ns TDI Input Hold Time tTDIH, t6 2 — 2 — ns TPC Output Delay Time tTPCDO, t8 -1 6 -1 6 ns PCST Output Delay Time tPCSTDO, t7 -1 6 -1 6 ns TRST* Low TIme tTRSTLow, t12 100 — 100 — ns TRST* Removal TIme tTRSTR, t13 3 — 3 — ns DC Electrical Characteristics — Commercial/Industrial Temperature Ranges—RC32364 VCC Core & VCC I/O = 3.3V ± 5%; TCase = 0°C to +85°C Commercial, TCase = -40° C to +85°C Industrial RC32364 100MHz Parameter RC32364 133MHz Conditions Min Max Min Max VOL — 0.1V — 0.1V VOH VCC - 0.1V — VCC - 0.1V — VOL — 0.4V — 0.4V VOH 2.4V — 2.4V — VIL –0.5V 0.2VCC –0.5V 0.2VCC — VIH 0.7VCC VCC +0.3V 0.7VCC VCC + 0.3V — CIN — 10pF — 10pF — COUT — 10pF — 10pF — I/OLEAK — 20uA — 20uA Input/Output Leakage |IOUT|= 20uA |IOUT|= 4mA 13 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ Output Loading For AC Testing VREF To Device Under Test – + +1.5V CLD Figure 3 Output Loading for AC Testing Signal Cld All Signals 50 pF Power Consumption — RC32364 Parameter System Condition: ICC P 1. RC32364 100MHz Typical Maximum 100/50MHz RC32364 133MHz Typical Conditions Maximum 133/67MHz — standby1 50mA 90mA 50mA 90mA CL = 50pF Tc = 25oC Vcc core & Vcc I/O = 3.65V active 160mA 180mA 200mA 250mA CL = 50pF TC = 25oC Vcc core, Vcc I/O = 3.65V 0.6W 0.7Watt 0.9 CL = 50pF TC = 25oC Vcc core, Vcc I/O = 3.65V power 0.58W dissipation Executing wait instruction Capacitive Load Deration — RC32364 Parameter Symbol Load Derate CLD Test Conditions — 100MHz 133MHz Min Max Min Max — 2 — 2 14 of 21 *Notice: The information in this document is subject to change without notice Units ns/25pF June 20, 2000 79RC32364™ Power Curves The following two graphs contain power curves that show power consumption at various bus frequencies. Note: Only pipeline frequencies that are integer multiples (2x, 3x, etc.) of bus frequencies are supported. 275.0 ICC (mA) 225.0 3x 6x 5x 4x 175.0 2x 2x 3x 4x 7x 5x 8x 6x 125.0 7x 8x 75.0 25.0 10 15 20 25 30 35 40 45 50 55 60 65 System Bus Speed (MHz) Figure 4 Typical Power Usage - RC32364 350.0 5x ICC (mA) 300.0 6x 3x 4x 2x 7x 250.0 2x 3x 4x 8x 5x 200.0 6x 150.0 7x 8x 100.0 50.0 10 15 20 25 30 35 40 45 50 55 60 65 System Bus Speed (MHz) Figure 5 Maximum Power Usage - RC32364 15 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ Timing Characteristics — RC32364 tMCKP tMCKLOW tMCKHIGH MasterClock Input Output tMCRISE tDS tMCFALL tDH tDO tDO ALE tDOH tDOA Ack* Retry* BusErr* tDSS tDH Figure 6 System Clocks Data Setup, Output, and Hold timing VCC MasterClock (MClk) ColdReset* Reset* ModeBit[9:0] >= 100 ms >= 10 ms >= 64 MClk cycles Figure 7 Mode Configuration Interface Reset Sequence 16 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ Standard JTAG Timing Figure 8 represents the timing diagram for the EJTAG interface signals. The standard JTAG connector is a 10-pin connector providing 5 signal and 5 ground pins. For Enhanced JTAG, a 24-pin connector has been chosen providing 12 signal pins and 12 ground pins. This guarantees the elimination of noise problems by incorporating a signal-ground type arrangement. TPC,PCST[2:0] capture t3 TCK t14 t14 t1 DCLK t11 t2 t15 t15 t9 TDI/DINT* TMS TDO/TPC, TPC[8:2] t5 TDO t6 TDO t10 TPC t8 t4 PCST[2:0], PCST t7 TRST* t13 t12 Notes to diagram: t1 = tTCKlow t2 = tTCKHIGH t3 = tTCK t4 = tTDODO t5 = tTDIS t6 = tTDIH t7 = tPCSTDO t8 = tTPCDO t9 = tDCKHIGH t10 = tDCKLOW t11 = tDCK t12 = tTRSTDO t13 = tTRSTR t14 = tTCK RISE, tTCK FALL t15 = tDCK RISE, tDCK FALL Figure 8 Standard JTAG timing 17 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ Table 4 shows the pin numbering for the Standard EJTAG (EJT) connector. All the even numbered pins are connected to GROUND. The two righthand most columns show the target signal direction and the recommended termination at the target. Target termination resistors may be internal to the chip or external on the board. PIN SIGNAL TARGET I/O TERMINATION1 1 TRST* (optional) Input 10 kΩ pull-down resistor 3 TDI/DINT* Input 10 kΩ pull-up resistor 5 TDO/TPC Output 33 Ω series resistor 7 TMS Input 10 kΩ pull-up resistor 9 TCK Input 10 kΩ pull-up resistor2 11 RST* Input 10 kΩ pull-up resistor 13 PCST[0] Output 33 Ω series 15 PCST[1] Output 33 Ω series 17 PCST[2] Output 33 Ω series 19 DCLK Output 33 Ω series 21 Debugboot Input 10 kΩ pull-down resistor 23 VIO Input Must be connected to the VCC IO supply of the device. Table 4 Pin Numbering of the JTAG and EJTAG Target Connector 1. The value of the series resistor may depend on the actual PCB layout situation. 2. TCK pull-up resistor is not required according to the JTAG (IEEE1149) standard. It is indicated here to prevent a floating CMOS input when the EJTAG connector is unconnected. 18 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ RC32364 Package Drawing — 144-pin TQFP (Note: The RC32364 is available in a 144-pin thin quad flat pack (TQFP) package.) 19 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ RC32364 Package Drawing — Page Two 20 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000 79RC32364™ Ordering Information IDT79RCXX Product Type YY Operating Voltage XXXX 999 Device Type Speed A Package A Temp range/ Process Blank Commercial Temperature Range (0°C to +85°C Case) I Industrial Temperature Range (-40°C to +85°C Case) DA 144-pin TQFP 100 133 100 MHz PClk 133 MHz PClk 364 Embedded Processor V 3.3V +/-5% 79RC32 32-bit Embedded Microprocessor Valid Combinations IDT79RC32V364 - 100,133 DA IDT79RC32V364 - 100,133 DAI TQFP package, Commercial Temperature TQFP package, Industrial Temperature CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com for Tech Support: email: rischelp@idt.com phone: 408-284-8208 The IDT logo is a trademark of Integrated Device Technology, Inc. 21 of 21 *Notice: The information in this document is subject to change without notice June 20, 2000