IDT8102-25VPCNSG

Active Crystals 8102 Ultra Low Power CrystalFree™ Oscillators Features        Frequency Range: Output Type: Initial Frequency Tolerance: Supply Voltage: Power Consumption: Standby Current: Standard Package:  Operating Temperature: PRELIMINARY DATA SHEET 4 to 50 MHz CMOS ± 50 ppm 1.8 to 3.3 V 1.9 mA (1.8 V) < 1 uA 5.0 x 3.2 mm 2.5 x 2.0 mm 0 to 70 °C -20 to 70 °C This product is rated “Green”, please contact factory for environmental compliancy information Specification Parameter Supply Voltage Output Frequency Initial Frequency Tolerance Supply Current Quiescent Current Input LOW level Input HIGH level Output LOW level Output HIGH level Tolerance over Temperature Rise/Fall Time Symmetry Start-up time Period Jitter Cycle to Cycle Jitter Symbol VDD FOUT FTOL IDD ISTBY VIL VIH VOL VOH FTEMP TR /TF SYM TST PJRMS CCJMAX Specifications 2.5 V 4 to 50 MHz ± 50 ppm 2.0 mA 1 uA (max) 0.3 VDD (max) 0.7 VDD (min) 0.1 VDD (max) 0.9 VDD (min) ± 100 ppm 2.3 ns 45% / 55% 400 us 6 ps 50 ps 1.8 V 1.9 mA 2.75 ns 17 ps 120 ps 3.3 V 2.2 mA Conditions Nominal See ordering code 25°C Typical; No load condition; 25°C STBY# = GND At STBY# pin 1.9 ns IOL = - 1 mA IOH = 1 mA -20 to 70°C 20% to 80% x VDD. Output load (CL) = 4 pF 5 ps 40 ps Output valid time after VDD meets the specified range & STBY# transition 4 pF load; 50 MHz 4 pF load; 50 MHz *Aging @25°C is negligible over lifetime Package Outline and Dimensions 3.20 ±0.05 Typical PCB Land Pattern Pin #1 ID Chamfer 0.5 x 45° 0.90 ±0.05 1.20 ±0.05 5.0 x 3.2 0.0-0.05 STBY# 4L SMD 5.0 x 3.2mm 5.00 ±0.05 VDD 2.5 (mm) 2.2 0.85 ±0.05 2.54 OUT 1.6 GND 0.203 Ref. Bottom View Top View 0.65 ±0.05 2.0 ±0.05 (mm) 4L SMD Top View June 1, 2011 2.5 ±0.05 STBY# VDD 0.152 Ref. 1.225 Bsc GND Bottom View www.IDT.com Side View OUT 0.9 2.5 x 2.0mm 1.5 0.0-0.05 0.55 ±0.05 1.8 2.5 x 2.0 0.75 ±0.05 Pin #1 ID Chamfer 0.35 x 45° 1.4 Side View 0.8 ©2011 Integrated Device Technology, Inc 8102 Datasheet CrystalFree™ Oscillator Solder Reflow Profile Absolute Maximum Ratings Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these or under any condition beyond those listed in the operating specifications is not implied. Exposure to absolute maximum rated conditions may affect product reliability. Name 1 2 3 4 STBY# GND OUT2 VDD ax cm 100 60-150 sec 60-180 sec 50 Time Output Waveform Pin Descriptions Pin # 150°C 150 3° C/ se Temperature (°C) 4.6 V -0.5 V to VDD + 0.5 V -0.5 V to VDD + 0.5 V -65°C to 150°C 217°C 200 ma x Maximum Absolute Rating VDD STBY# OUT Storage Temperature (260°C max) /sec 6°C Item 40 sec (max) 245°C 250 Description TR Standby Mode1 (0 = Output Disabled) Ground CMOS Output Power TF VOH 0.8 VDD 0.5 VDD 1. Pulled high internally 2. Weak pull down to GND during STBY# enable and startup 0.2 VDD VOL SYM = t1 / t2 t1 t2 Time Ordering Information 8102Frequency 4 to 50MHz 6024 Silver Creek Valley Road San Jose, California 95138 50 VPC NS G Package NSG: 5.0 x 3.2 (4 pin) NVG: 2.5 x 2.0 (4 pin) Sales 800-345-7015 (inside USA) +1 408-284-8200 (outside USA) Fax: 408-284-2775 E Temp Blank: 0 to 70°C E: -20 to 70°C T Shipping Blank: Tubes T: Tape and Reel Technical Support crystalfreetechsupport@idt.com +1 408-739-5400 DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2010, 2011. All rights reserved. June 1, 2011 www.IDT.com ©2011 Integrated Device Technology, Inc