ISL28230CBZ-T7

DATASHEET ISL28130, ISL28230, ISL28430 FN7623 Rev 7.00 February 13, 2014 Single, Dual, and Quad Micropower, Low Drift, RRIO Operational Amplifiers The ISL28130, ISL28230 and ISL28430 are single, dual and quad micropower, low offset drift operational amplifiers that are optimized for single and dual supply operation from 1.8V to 5.5V and ±0.9V to ±2.75V. Their low supply current of 20µA and rail-to-rail input/output enable the ISL28130, ISL28230, and ISL28430 to be an excellent general-purpose op amp for a range of applications. The ISL28130, ISL28230 and ISL28430 are ideal for handheld devices that operate off 2AA or single Li-ion batteries. The ISL28130 is available in industry standard pinouts for 5 Ld SOT-23, 5 Ld SC70 and 8 Ld SOIC packages. The ISL28230 is available in industry standard pinouts for 8 Ld MSOP, 8 Ld SOIC and 8 Ld DFN packages. The ISL28430 is available in 14 Ld TSSOP and 14 Ld SOIC packages. Commercial devices operate over the temperature range of 0°C to 70°C. Full temperature range devices operate over the temperature range of -40°C to 125°C. Features • Low input offset voltage . . . . . . . . . . . . . . . . . . . . . 40µV, Max. • Low offset drift . . . . . . . . . . . . . . . . . . . . . . . . .150nV/°C, Max. • Input bias current. . . . . . . . . . . . . . . . . . . . . . . . . . 250pA, Max. • Quiescent current (per amplifier) . . . . . . . . . . . . . . .20µA, Typ. • Single supply range . . . . . . . . . . . . . . . . . . . . . .+1.8V to +5.5V • Dual supply range . . . . . . . . . . . . . . . . . . . . . .±0.9V to ±2.75V • Low noise (0.01Hz to 10Hz) . . . . . . . . . . . . . . . . 1.1µVP-P, Typ. • Rail-to-rail inputs and output Applications • Bi-directional current sense • Temperature measurement • Medical equipment • Electronic weigh scales • Precision/strain gauge sensor • Precision regulation • Low Ohmic current sense • High gain analog front ends 400 499k VREF 4.99k + V+ 0.1 4.99k VSENSE OUT V499k GND I-SENSE- BI-DIRECTIONAL CURRENT SENSE AMPLIFIER FIGURE 1. TYPICAL APPLICATION DIAGRAM FN7623 Rev 7.00 February 13, 2014 INPUT BIAS CURRENT (pA) V+ +1.8V TO +5.5V I-SENSE+ 300 200 VS = ±2.5V VS = ±0.9V 100 0 -100 -50 -25 0 25 50 75 100 TEMPERATURE (°C) FIGURE 2. IB vs TEMPERATURE Page 1 of 19 125 ISL28130, ISL28230, ISL28430 Ordering Information PART NUMBER (Notes 3, 4) PART MARKING TEMP RANGE (°C) TEMPERATURE GRADE PACKAGE (Pb-Free) PKG. DWG. # ISL28130CHZ-T7 (Note 2) BDPA (Note 5) 0 to +70 Commercial 5 Ld SOT-23 P5.064A ISL28130CHZ-T7A (Note 2) BDPA (Note 5) 0 to +70 Commercial 5 Ld SOT-23 P5.064A ISL28130FHZ-T7 (Note 2) BEFA (Note 5) -40 to +125 Full 5 Ld SOT-23 P5.064A ISL28130FHZ-T7A (Note 2) BEFA (Note 5) -40 to +125 Full 5 Ld SOT-23 P5.064A ISL28130CEZ-T7 (Note 2) BLA (Note 5) 0 to +70 Commercial 5 Ld SC-70 P5.049 ISL28130CEZ-T7A (Note 2) BLA (Note 5) 0 to +70 Commercial 5 Ld SC-70 P5.049 ISL28130FEZ-T7 (Note 2) BNA (Note 5) -40 to +125 Full 5 Ld SC-70 P5.049 ISL28130FEZ-T7A (Note 2) BNA (Note 5) -40 to +125 Full 5 Ld SC-70 P5.049 ISL28230CUZ (Note 1) 8230Z 0 to +70 Commercial 8 Ld MSOP M8.118A ISL28230FUZ (Note 1) 8230F -40 to +125 Full 8 Ld MSOP M8.118A ISL28230CBZ (Note 1) 28230 CBZ 0 to +70 Commercial 8 Ld SOIC M8.15E ISL28230FBZ (Note 1) 28230 FBZ -40 to +125 Full 8 Ld SOIC M8.15E ISL28230CRZ (Note 1) 230Z 0 to +70 Commercial 8 Ld 3mmx3mm DFN L8.3x3J ISL28230FRZ (Note 1) 230F -40 to +125 Full 8 Ld 3mmx3mm DFN L8.3x3J ISL28430CBZ (Note 1) 28430 CBZ 0 to +70 Commercial 14 Ld SOIC MDP0027 ISL28430FBZ (Note 1) 28430 FBZ -40 to +125 Full 14 Ld SOIC MDP0027 ISL28430CVZ (Note 1) 28430 CVZ 0 to +70 Commercial 14 Ld TSSOP MDP0044 ISL28430FVZ (Note 1) 28430 FVZ -40 to +125 Full 14 Ld TSSOP MDP0044 NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. Please refer to TB347 for details on reel specifications. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 4. For Moisture Sensitivity Level (MSL), please see device information page for ISL28130, ISL28230, ISL28430. For more information on MSL please see Tech Brief TB363. 5. The part marking is located on the bottom of the part. FN7623 Rev 7.00 February 13, 2014 Page 2 of 19 ISL28130, ISL28230, ISL28430 Pin Configurations ISL28130 (8 LD SOIC) TOP VIEW ISL28130 (5 LD SOT-23) TOP VIEW 1 V- 2 IN+ 3 5 V+ + 4 IN- NC 1 8 NC IN- 2 7 V+ - + OUT IN+ 3 6 OUT V- 4 ISL28230 (8 LD MSOP, SOIC) TOP VIEW ISL28130 (5 LD SC-70) TOP VIEW IN+ 1 V- 2 IN- 3 5 NC 5 V+ + - OUT_A 1 IN-_A 2 4 OUT 8 V+ 7 OUT_B - + IN+_A 3 + - V- 4 IN-_A 8 V+ 1 2 IN+_A 3 V- 4 PAD 5 IN+_B ISL28430 (14 LD TSSOP, SOIC) TOP VIEW ISL28230 (8 LD DFN) TOP VIEW OUT_A 14 OUT_D OUT_A 1 7 OUT_B IN-_A 2 6 IN-_B IN+_A 3 5 IN+_B V+ 4 - + + - 11 V- + - OUT_B 7 10 IN+_C - + IN-_B 6 13 IN-_D 12 IN+_D IN+_B 5 FN7623 Rev 7.00 February 13, 2014 6 IN-_B 9 IN-_C 8 OUT_C Page 3 of 19 ISL28130, ISL28230, ISL28430 Pin Descriptions ISL28130 (5 Ld SOT-23) ISL28130 (8 Ld SOIC) ISL28130 (5 LD SC-70) 3 3 1 ISL28430 ISL28230 (14 Ld PIN (8 Ld MSOP, SOIC, DFN) TSSOP, SOIC) NAME 3 5 - 3 5 10 12 FUNCTION Non-inverting input IN+ IN+_A IN+_B IN+_C IN+_D EQUIVALENT CIRCUIT V+ + IN- IN+ VCircuit 1 2 4 2 4 2 3 1 6 4 11 V- Negative supply 2 6 9 13 ININ-_A IN-_B IN-_C IN-_D Inverting input 2 6 1 7 - 1 7 8 14 OUT Output OUT_A OUT_B OUT_C OUT_D 4 (See “Circuit 1”) V+ OUT VCircuit 2 5 7 5 8 4 V+ Positive supply - 1, 5, 8 - - - NC Not Connected – This pin is not electrically connected internally. - - - PAD - Paddle FN7623 Rev 7.00 February 13, 2014 Thermal Pad. Connect to most negative supply. DFN packages only. Page 4 of 19 ISL28130, ISL28230, ISL28430 Absolute Maximum Ratings Thermal Information Max Supply Voltage V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5V Max Voltage VIN to GND . . . . . . . . . . . . . . . . . . . . (V- - 0.3V) to (V+ + 0.3V)V Max Input Differential Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5V Max Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Max Voltage VOUT to GND (10s) . . . . . . . . . . . . . . (V- - 0.5V) to (V+ + 0.5V)V ESD Tolerance (ISL28130) Human Body Model (Tested at JESD22-A114F) . . . . . . . . . . . . . . . 3000V Machine Model (Tested at JESD22-A115B) . . . . . . . . . . . . . . . . . . . 200V Charged Device Model (Tested at JESD22-C110D) . . . . . . . . . . . . 1500V ESD Tolerance (ISL28230, ISL28430) Human Body Model (Tested at JESD22-A114F) . . . . . . . . . . . . . . . 4000V Machine Model (Tested at JESD22-A115B) . . . . . . . . . . . . . . . . . . . 400V Charged Device Model (Tested at JESD22-C110D) . . . . . . . . . . . . 2000V Latch-Up (Passed Per JESD78B). . . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C Thermal Resistance (Typical) JA (°C/W) JC (°C/W) 5 Ld SOT-23 (Notes 6, 8) . . . . . . . . . . . . . . . 225 110 5 Ld SC70 (Notes 6, 8). . . . . . . . . . . . . . . . . 206 146 8 Ld SOIC (ISL28130) (Notes 6, 8) . . . . . . . 135 95 8 Ld MSOP (Notes 6, 8) . . . . . . . . . . . . . . . . 180 65 8 Ld SOIC (ISL28230) (Notes 6, 8). . . . . . . 125 90 8 Ld DFN (Notes 7, 9). . . . . . . . . . . . . . . . . . 53 12 14 Ld TSSOP (Notes 6, 8) . . . . . . . . . . . . . . 110 40 14 Ld SOIC (Notes 6, 8) . . . . . . . . . . . . . . . . 75 47 Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range Full Grade Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C Commercial Grade Devices. . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 6. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 7. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 8. For JC, the “case temp” location is taken at the package top center. 9. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications entire operating temperature range. V+ = 5V, V- = 0V, VCM = 2.5V, TA = +25°C, RL = 10kΩ, unless otherwise specified. Boldface limits apply over the (Note 10) TYP MAX (Note 10) UNIT Vs = 1.8V to 5.5V -40 ±5 40 µV Vs = 1.8 to 5.5V; T = 0°C to +70°C -46.8 46.8 µV -55 55 µV 150 nV/°C MIN PARAMETER DESCRIPTION CONDITIONS DC SPECIFICATIONS VOS Input Offset Voltage Vs = 1.8V to 5.5V; T = -40°C to +125°C TCVOS Input Offset Voltage Temperature Coefficient IOS Input Offset Current -60 pA TCIOS Input Offset Current Temperature Coefficient 0.11 pA/°C IB Input Bias Current Common Mode Input Voltage Range CMRR Common Mode Rejection Ratio -150 20 T = 0°C to +70°C -250 250 pA T = -40°C to +125°C -700 700 pA Guaranteed by CMRR -0.1 5.1 V VCM = -0.1V to 5.1V 110 125 dB 105 PSRR Power Supply Rejection Ratio Vs = 2.0V to 5.5V 105 dB 138 dB 105 VOH Output Voltage Swing, High VOL Output Voltage Swing, Low FN7623 Rev 7.00 February 13, 2014 4.950 dB 4.981 18 V 50 mV Page 5 of 19 ISL28130, ISL28230, ISL28430 Electrical Specifications V+ = 5V, V- = 0V, VCM = 2.5V, TA = +25°C, RL = 10kΩ, unless otherwise specified. Boldface limits apply over the entire operating temperature range. (Continued) MIN PARAMETER DESCRIPTION CONDITIONS AOL Open Loop Gain RL = 1MΩ V+ Supply Voltage Guaranteed by VOS IS Supply Current, Per Amplifier RL = OPEN (Note 10) TYP MAX (Note 10) 150 1.8 20 UNIT dB 5.5 V 25 µA 35 µA ISC+ Output Source Short Circuit Current RL = Short V- 15 mA ISC- Output Sink Short Circuit Current RL = Short V+ -15 mA GBWP Gain Bandwidth Product AV = 100, RF = 100kΩRG = 1kΩ, RL = 10kΩto VCM 400 kHz eN VP-P Peak-to-Peak Input Noise Voltage f = 0.01Hz to 10Hz 1.1 µVP-P eN Input Noise Voltage Density f = 1kHz 65 nV/(Hz) iN Input Noise Current Density f = 1kHz 72 fA/(Hz) f = 10Hz 80 fA/(Hz) f = 1MHz 1.6 pF 1.12 pF 0.2 V/µs 0.1 V/µs 1.1 µs 1.1 µs 20 µs 30 µs 35 µs 10.5 µs AC SPECIFICATIONS Cin Differential Input Capacitance Common Mode Input Capacitance TRANSIENT RESPONSE SR Positive Slew Rate VOUT = 1V to 4V, RL = 10kΩ Negative Slew Rate tr, tf, Small Signal Rise Time, tr 10% to 90% Fall Time, tf 10% to 90% tr, tf Large Signal Rise Time, tr 10% to 90% Fall Time, tf 10% to 90% AV = +1, VOUT = 0.1VP-P RF = 0Ω, RL = 10kΩ,CL = 1.2pF AV = +1, VOUT = 2VP-P RF = 0Ω, RL = 10kΩ, CL = 1.2pF ts Settling Time to 0.1%, 2VP-P Step AV = +1, RF = 0Ω,RL = 10kΩ, CL = 1.2pF trecover Output Overload Recovery Time, Recovery to 90% of Output Saturation AV = +2, RF = 10kΩ, RL = Open CL = 3.7pF NOTE: 10. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. FN7623 Rev 7.00 February 13, 2014 Page 6 of 19 ISL28130, ISL28230, ISL28430 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open, T = +25°C, unless otherwise specified. 400 400 300 300 200 INPUT BIAS CURRENT (pA) INPUT BIAS CURRENT (pA) n VS = ±2.5V 100 VS = ±0.9V 0 -100 -50 -25 0 25 50 75 100 200 VS = ±2.5V VS = ±0.9V 100 0 -100 -50 125 -25 0 TEMPERATURE (°C) 40 75 100 125 100 125 40 PER AMPLIFIER PER AMPLIFIER 35 SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 50 FIGURE 4. IB- vs TEMPERATURE FIGURE 3. IB+ vs TEMPERATURE 30 25 20 15 10 -50 -25 0 25 50 75 100 35 30 25 20 15 10 -50 125 -25 0 TEMPERATURE (°C) 25 50 75 TEMPERATURE (°C) FIGURE 6. SUPPLY CURRENT vs TEMPERATURE, Vs = ±2.5V FIGURE 5. SUPPLY CURRENT vs TEMPERATURE, Vs = ±0.9V 21 200 OPEN LOOP GAIN (dB)/PHASE (°) SUPPLY CURRENT (µA) 25 TEMPERATURE (°C) 20 19 18 17 16 1.5 VIN = 0V RL = OPEN 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) FIGURE 7. SUPPLY CURRENT vs SUPPLY VOLTAGE FN7623 Rev 7.00 February 13, 2014 6.0 150 PHASE 100 50 GAIN 0 -50 RL = 10M CL = 100pF SIMULATION -100 0.1m 1m 10m 100m 1 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FIGURE 8. FREQUENCY RESPONSE vs OPEN LOOP GAIN, RL = 10MΩ Page 7 of 19 ISL28130, ISL28230, ISL28430 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open, T = +25°C, unless otherwise specified. 1 1 -1 RL = 1k -2 -3 RL = 10k -4 RL = 49.9k RL = OPEN -5 VS = ±0.9V CL = 3.7pF AV = +1 VOUT = 10mVP-P -6 -7 -8 -9 100 RL = 1k -1 -2 RL = 10k -4 RL = 49.9k -5 VS = ±2.5V CL = 3.7pF AV = +1 VOUT = 10mVP-P -6 -7 -8 1k 10k 100k FREQUENCY (Hz) 1M -9 100 10M -1 NORMALIZED GAIN (dB) 0 8 RF = RG = 1k 7 6 RF = RG = 10k 5 4 3 2 1 0 100 RF = RG = 100k VS = ±2.5V RL = 100k CL = 3.7pF AV = +2 VOUT = 10mVP-P 1k 10k 100k FREQUENCY (Hz) 1M 10M -3 VOUT = 500mV -4 -5 VOUT = 250mV -6 VS = ±2.5V -7 R = OPEN L -8 CL = 3.7pF AV = 1 -9 100 1k RG = 100, RF = 100k VOUT = 10mV 10k 100k FREQUENCY (Hz) 1M 10M 0 RG = 1k, RF = 100k AV = 100 V+ = 5V CL = 3.7pF RL = 100k VOUT = 10mVP-P 30 AV = 10 RG = 10k, RF = 100k 10 AV = 1 1k 10k 100k 1M 10M FREQUENCY (Hz) FIGURE 13. FREQUENCY RESPONSE vs CLOSED LOOP GAIN FN7623 Rev 7.00 February 13, 2014 -1 -2 VS = ±0.9V -3 -4 VS= ±1.5V -5 VS = ±2.75V -6 -7 -8 RG = OPEN, RF = 0 100 NORMALIZED GAIN (dB) GAIN (dB) VOUT = 100mV 1 AV = 1000 50 -10 10 10M FIGURE 12. GAIN vs FREQUENCY vs VOUT 70 0 1M VOUT = 1V -2 FIGURE 11. GAIN vs FREQUENCY vs FEEDBACK RESISTOR VALUES RF/RG 20 10k 100k FREQUENCY (Hz) 1 9 40 1k FIGURE 10. GAIN vs FREQUENCY vs RL, VS = ±2.5V 10 60 RL = OPEN -3 FIGURE 9. GAIN vs FREQUENCY vs RL, VS = ±0.9V GAIN (dB) RL = 100k 0 RL = 100k NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 0 RL = 100k CL = 3.7pF AV = +1 VOUT = 10mVP-P -9 100 1k 10k 100k FREQUENCY (Hz) 1M FIGURE 14. GAIN vs FREQUENCY vs SUPPLY VOLTAGE Page 8 of 19 10M ISL28130, ISL28230, ISL28430 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open, T = +25°C, unless otherwise specified. 8 5.0 CL = 824pF 4.5 CL = 474pF 4 4.0 CL = 224pF 2 3.5 SIGNAL (V) NORMALIZED GAIN (dB) 6 0 -2 CL = 104pF -4 3.0 2.5 2.0 CL = 51pF -6 VS = ±2.5V RL = 100k -8 AV = +1 V = 10mVP-P -10 OUT 100 1k RL = 100k CL = 3.7pF AV = 1 VOUT = 4VP-P 1.5 1.0 CL = 3.7pF 0.5 10k 100k 1M 0 10M 0 50 100 150 FREQUENCY (Hz) FIGURE 15. GAIN vs FREQUENCY vs CL 400 0.12 0.10 SIGNAL (V) 0.8 SIGNAL (V) 350 0.14 1.0 0.6 0.4 RL = 100k CL = 3.7pF AV = 1 VOUT = 1VP-P 0.2 0 10 20 30 40 50 60 TIME (µs) 0.08 0.06 5.000 0.02 70 80 90 0 0 100 5 10 15 20 25 TIME (µs) 30 35 40 FIGURE 18. SMALL SIGNAL STEP RESPONSE (100mV) 40 VS = 5V RL = 10kΩ 35 4.990 30 VOL (mV) 4.995 4.985 4.980 4.975 -50 RL = 100k CL = 3.7pF AV = 1 VOUT = 100mVP-P 0.04 FIGURE 17. LARGE SIGNAL STEP RESPONSE (1V) VOH (V) 300 FIGURE 16. LARGE SIGNAL STEP RESPONSE (4V) 1.2 0 200 250 TIME (µs) VS = 5V RL = 10kΩ 25 20 -25 0 25 50 75 TEMPERATURE (°C) FIGURE 19. VOH vs TEMPERATURE FN7623 Rev 7.00 February 13, 2014 100 125 15 -50 -25 0 25 50 75 100 125 TEMPERATURE (°C) FIGURE 20. VOL vs TEMPERATURE Page 9 of 19 ISL28130, ISL28230, ISL28430 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open, T = +25°C, unless otherwise specified. -20 -20 Vs = ±0.9V RL = OPEN CL = 3.7pF AV = 1 VOUT = 1VP-P -60 Vs = ±2.5V RL = OPEN CL = 3.7pF AV = 1 VOUT = 1VP-P -40 CROSSTALK (dB) CROSSTALK (dB) -40 -80 -100 -120 -60 -80 -100 -120 -140 1k 10k 100k FREQUENCY (Hz) FIGURE 21. CROSSTALK vs FREQUENCY, V S = ±0.9V FN7623 Rev 7.00 February 13, 2014 1M -140 1k 10k 100k FREQUENCY (Hz) FIGURE 22. CROSSTALK vs FREQUENCY, VS = ±2.5V Page 10 of 19 1M ISL28130, ISL28230, ISL28430 Applications Information Layout Guidelines for High Impedance Inputs Functional Description To achieve maximum performance from the high input impedance and low offset voltage of the ISL28130, ISL28230 and ISL28430 amplifiers, care should be taken in the circuit board layout. The PC board surface must remain clean and free of moisture to avoid leakage currents between adjacent traces. Surface coating of the circuit board reduces surface moisture and provides a humidity barrier, reducing parasitic resistance on the board. The ISL28130, ISL28230 and ISL28430 are low offset and low drift operational amplifiers with a very high open loop gain (150dB) and rail-to-rail input/output. They are designed to operate on a single supply range of 1.8V to 5.5V or a dual supply range of ±0.9V to ±2.75V while consuming only 20µA of supply current per channel. The ISL28130, ISL28230 and ISL28430 have a 400kHz gain-bandwidth. The high open loop gain, low offset voltage, high bandwidth and low 1/f noise make the ISL28130, ISL28230 and ISL28430 ideal for precision applications. Rail-to-rail Input and Output (RRIO) The RRIO CMOS amplifier uses parallel input PMOS and NMOS that enable the inputs to swing 100mV beyond either supply rail. The inverting and non-inverting inputs do not have back-to-back input clamp diodes and are capable of maintaining high input impedance at high differential input voltages. This is effective in eliminating output distortion caused by high slew rate input signals. The output stage uses common source connected PMOS and NMOS devices to achieve rail-to-rail output drive capability with 15mA current limit and the capability to swing to within 50mV of either rail while driving a 10kΩ load. IN+ and IN- Protection High Gain, Precision DC-Coupled Amplifier The circuit in Figure 24 implements a single-stage DC-coupled amplifier with an input DC sensitivity of under 100nV that is only possible using a low VOS amplifier with high open loop gain. High gain DC amplifiers operating from low voltage supplies are not practical using typical low offset precision op amps. For example, consider a typical precision amplifier in a gain of 10kV/V. A low offset op amp with ±100µV VOS and 0.5µV/°C offset drift yields a DC error of >1V, with an additional 5mV/°C of temperature-dependent error. This amount of error makes it difficult to resolve DC input voltage changes in the mV range. The ±40µV max VOS and 150nV/°C temperature drift of the ISL28130, ISL28230, and ISL28430 produce a temperature-stable maximum DC output error of only ±400mV, with a maximum output temperature drift of 1.5mV/°C. The additional benefit of a very low 1/f noise corner frequency and some feedback filtering allows DC voltages and voltage fluctuations well below 10µV to be easily detected with a simple, single-stage amplifier. All input terminals have internal ESD protection diodes to both positive and negative supply rails, limiting the input voltage to within one diode beyond the supply rails. For applications in which either input is expected to exceed the rails by 0.5V, an external series resistor must be used to ensure the input currents never exceed 20mA (see Figure 23). CF 0.018µF 1MΩ +2.5V VIN VIN RIN + VOUT RL 100Ω 1MΩ VOUT RL + 100Ω -2.5V ACL = 10kV/V FIGURE 23. INPUT CURRENT LIMITING FIGURE 24. HIGH GAIN, PRECISION DC-COUPLED AMPLIFIER © Copyright Intersil Americas LLC 2010-2014. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN7623 Rev 7.00 February 13, 2014 Page 11 of 19 ISL28130, ISL28230, ISL28430 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest revision. DATE REVISION February 13, 2014 FN7623.7 CHANGE November 22, 2013 FN7623.6 Removed “Coming Soon” from ISL28430FBZ in “Ordering Information” on page 2. November 8, 2012 FN7623.5 Removed “Coming Soon” from ISL28130FHZ-T7, ISL28130FEZ-T7, ISL28130CBZ, ISL28130FBZ, ISL28230FUZ, ISL28230FRZ, ISL28430FVZ, ISL28230FRZ, ISL28130CBZ and ISL28130FBZ in “Ordering Information” on page 2. February 10, 2012 FN7623.4 Removed “Coming Soon” from ISL28230FBZ in “Ordering Information” on page 2. June 13, 2011 FN7623.3 • Changed minimum operating supply voltage from +1.65V to +1.8V throughout datasheet. Modified Electrical Specifications table, beginning on page 5, for all specs related at +1.65V to +1.8V, and all other text references accordingly. • On page 1, paragraph 2, last sentence: changed from “All devices operate over the temperature range of 40°C to +125°C.” to “Commercial temp range devices operate over the temperature range of 0°C to 70°C. Full temp range devices operate over the temperature range of -40°C to 125°C.” • On page 2, Ordering Information: added “Coming Soon” to all devices with -40°C to 125°C temp range and to ISL28130CBZ at 0°C to +70°C temp range. March 1, 2011 FN7623.2 -Ordering Information Table: Removed all 'Coming Soon' under part numbers (except for ISL28130FBZ and ISL28230FRZ), added part markings for all 125°C grade parts. Added new data column called 'TEMPERATURE GRADE' to distinguish between 'Commercial' and 'Full' temp grades. - Electrical Specifications Table: added new text to common conditions: “Boldface limits apply over the entire operating temperature range”. This note allows bold face limits to apply both to commercial and full grade temp devices. - Added over temperature 0°C to 70°C spec for Vos in addition to -40°C to 125°C Vos spec. Original Vos spec of 46.8µV for -40°C to 125°C is a typo based on a TCVos of 150nV/C. -40°C to 125°C limit corrected as 55µV over temp. December 7, 2010 FN7623.1 Corrected Thermals for DFN package in “Tja from 125 to 53, “Tjc from 90 to 12” Ordering information table on page 2: Added part number ISL28230FRZ - Absolute Maximum Ratings table on page 5: changed Max Voltage VOUT to GND (10s) : from ±3.0V to: (V- - 0.5V) to (V+ + 0.5V)V.. December 3, 2010 Removed Part Markings from Full temp grade parts and changed to TBD until availability is validated. December 2, 2010 -Updated front page text to add DFN packaging and extended temp range -40°C to +125°C -Removed previous Ib vs Temp plot and added new -40°C to +125°C Ib vs Temp plot on front page. -Updated ordering information table by adding a full temp range option to all parts and temp range column. Also added in DFN part to ordering table. All full temp parts are stamped Coming Soon. -Added DFN package to Pin Configurations table. -Added -40°C to +125°C temp range under Operating Conditions page 5. -Added the testing standards performance information to the ESD ratings in Abs Max Table -Added new Input Bias Current Ib spec of 700pA MIN/MAX in Electrical Spec table for -40°C to +125°C temp range -Revised Note 10 for Electrical Spec table as: “Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.” -Updated all curves in the datasheet with 0°C to +70°C temp range to -40°C to +125°C temp range. -Added DFN package L8.3x3J outline drawing to the end of datasheet. October 19, 2010 On page 6 changed “Supply Current, Per Amplifier” from a typical of 18µA to 20µA to comply with front page. August 17, 2010 FN7623.0 Initial Release About Intersil Intersil Corporation is a leader in the design and manufacture of high-performance analog, mixed-signal and power management semiconductors. The company's products address some of the largest markets within the industrial and infrastructure, personal computing and high-end consumer markets. For more information about Intersil, visit our website at www.intersil.com. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/en/support/ask-an-expert.html. Reliability reports are also available from our website at http://www.intersil.com/en/support/qualandreliability.html#reliability FN7623 Rev 7.00 February 13, 2014 Page 12 of 19 ISL28130, ISL28230, ISL28430 Small Outline Transistor Plastic Packages (SC70-5) P5.049 D 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE VIEW C e1 INCHES 5 4 E CL 1 2 CL 3 E1 b e CL 0.20 (0.008) M C C CL A A2 SEATING PLANE A1 -C- SYMBOL MIN MAX MIN MAX NOTES A 0.031 0.043 0.80 1.10 - A1 0.000 0.004 0.00 0.10 - A2 0.031 0.039 0.80 1.00 - b 0.006 0.012 0.15 0.30 b1 0.006 0.010 0.15 0.25 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.009 0.08 0.20 6 D 0.073 0.085 1.85 2.15 3 E 0.071 0.094 1.80 2.40 - E1 0.045 0.053 1.15 1.35 3 e e1 L 0.10 (0.004) C WITH PLATING b1 0.0256 Ref 0.0512 Ref 0.010 c1 0.018 - 1.30 Ref 0.26 - 0.46 0.017 Ref. 0.420 Ref. L2 0.006 BSC 0.15 BSC 0o N c 0.65 Ref L1  b MILLIMETERS 8o 0o 5 4 - 8o - 5 5 R 0.004 - 0.10 - R1 0.004 0.010 0.15 0.25 Rev. 3 7/07 NOTES: BASE METAL 1. Dimensioning and tolerances per ASME Y14.5M-1994. 2. Package conforms to EIAJ SC70 and JEDEC MO-203AA. 4X q1 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. R1 4. Footlength L measured at reference to gauge plane. 5. “N” is the number of terminal positions. R GAUGE PLANE SEATING PLANE L C L1 a L2 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. 4X q1 VIEW C 0.4mm 0.75mm 2.1mm 0.65mm TYPICAL RECOMMENDED LAND PATTERN FN7623 Rev 7.00 February 13, 2014 Page 13 of 19 ISL28130, ISL28230, ISL28430 Package Outline Drawing P5.064A 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 0, 2/10 1.90 0-3° D A 0.08-0.20 5 4 PIN 1 INDEX AREA 2.80 3 1.60 3 0.15 C D 2x 2 5 (0.60) 0.20 C 2x 0.95 SEE DETAIL X B 0.40 ±0.05 3 END VIEW 0.20 M C A-B D TOP VIEW 10° TYP (2 PLCS) 2.90 5 H 0.15 C A-B 2x C 1.45 MAX 1.14 ±0.15 0.10 C SIDE VIEW SEATING PLANE (0.25) GAUGE PLANE 0.45±0.1 0.05-0.15 4 DETAIL "X" (0.60) (1.20) NOTES: (2.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 3. Dimension is exclusive of mold flash, protrusions or gate burrs. 4. Foot length is measured at reference to guage plane. 5. This dimension is measured at Datum “H”. 6. Package conforms to JEDEC MO-178AA. (0.95) (1.90) TYPICAL RECOMMENDED LAND PATTERN FN7623 Rev 7.00 February 13, 2014 Page 14 of 19 ISL28130, ISL28230, ISL28430 Package Outline Drawing M8.118A 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP) Rev 0, 9/09 3.0±0.1 8 A 0.25 CAB 3.0±0.1 4.9±0.15 DETAIL "X" 1.10 Max PIN# 1 ID B SIDE VIEW 2 1 0.18 ± 0.05 2 0.65 BSC TOP VIEW 0.95 BSC 0.86±0.09 H GAUGE PLANE C 0.25 SEATING PLANE 0.33 +0.07/ -0.08 0.08 C A B 0.10 ± 0.05 3°±3° 0.10 C 0.55 ± 0.15 DETAIL "X" SIDE VIEW 1 5.80 NOTES: 4.40 3.00 1. Dimensions are in millimeters. 2. Dimensioning and tolerancing conform to JEDEC MO-187-AA and AMSE Y14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.25mm max per side are not included. 5. Dimensions “D” and “E1” are measured at Datum Plane “H”. 6. This replaces existing drawing # MDP0043 MSOP 8L. 0.65 0.40 1.40 TYPICAL RECOMMENDED LAND PATTERN FN7623 Rev 7.00 February 13, 2014 Page 15 of 19 ISL28130, ISL28230, ISL28430 Thin Shrink Small Outline Package Family (TSSOP) 0.25 M C A B D MDP0044 A THIN SHRINK SMALL OUTLINE PACKAGE FAMILY (N/2)+1 N MILLIMETERS SYMBOL 14 LD 16 LD 20 LD 24 LD 28 LD TOLERANCE PIN #1 I.D. E E1 0.20 C B A 1 (N/2) B 2X N/2 LEAD TIPS TOP VIEW 0.05 e C SEATING PLANE 0.10 M C A B b 0.10 C N LEADS H A 1.20 1.20 1.20 1.20 1.20 Max A1 0.10 0.10 0.10 0.10 0.10 ±0.05 A2 0.90 0.90 0.90 0.90 0.90 ±0.05 b 0.25 0.25 0.25 0.25 0.25 +0.05/-0.06 c 0.15 0.15 0.15 0.15 0.15 +0.05/-0.06 D 5.00 5.00 6.50 7.80 9.70 ±0.10 E 6.40 6.40 6.40 6.40 6.40 Basic E1 4.40 4.40 4.40 4.40 4.40 ±0.10 e 0.65 0.65 0.65 0.65 0.65 Basic L 0.60 0.60 0.60 0.60 0.60 ±0.15 L1 1.00 1.00 1.00 1.00 1.00 Reference Rev. F 2/07 NOTES: 1. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15mm per side. SIDE VIEW 2. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm per side. SEE DETAIL “X” 3. Dimensions “D” and “E1” are measured at dAtum Plane H. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c END VIEW L1 A A2 GAUGE PLANE 0.25 L A1 0° - 8° DETAIL X FN7623 Rev 7.00 February 13, 2014 Page 16 of 19 ISL28130, ISL28230, ISL28430 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 NOTES: Rev. M 2/07 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 FN7623 Rev 7.00 February 13, 2014 Page 17 of 19 ISL28130, ISL28230, ISL28430 Package Outline Drawing M8.15E 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 0, 08/09 4 4.90 ± 0.10 A DETAIL "A" 0.22 ± 0.03 B 6.0 ± 0.20 3.90 ± 0.10 4 PIN NO.1 ID MARK 5 (0.35) x 45° 4° ± 4° 0.43 ± 0.076 1.27 0.25 M C A B SIDE VIEW “B” TOP VIEW 1.75 MAX 1.45 ± 0.1 0.25 GAUGE PLANE C SEATING PLANE 0.10 C 0.175 ± 0.075 SIDE VIEW “A 0.63 ±0.23 DETAIL "A" (1.27) (0.60) NOTES: (1.50) (5.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. The pin #1 identifier may be either a mold or mark feature. 6. Reference to JEDEC MS-012. TYPICAL RECOMMENDED LAND PATTERN FN7623 Rev 7.00 February 13, 2014 Page 18 of 19 ISL28130, ISL28230, ISL28430 Package Outline Drawing L8.3x3J 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE Rev 0 9/09 2X 1.950 3.00 B 0.15 8 5 3.00 (4X) 6X 0.65 A 1.64 +0.10/ - 0.15 6 PIN 1 INDEX AREA 4 8X 0.30 8X 0.400 ± 0.10 TOP VIEW 6 PIN #1 INDEX AREA 1 4 0.10 M C A B 2.38 +0.10/ - 0.15 BOTTOM VIEW SEE DETAIL "X" ( 2.38 ) ( 1.95) 0.10 C Max 1.00 C 0.08 C SIDE VIEW ( 8X 0.60) (1.64) ( 2.80 ) PIN 1 C 0 . 2 REF 5 (6x 0.65) 0 . 00 MIN. 0 . 05 MAX. ( 8 X 0.30) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. FN7623 Rev 7.00 February 13, 2014 The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. Page 19 of 19