DATASHEET
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
±60V Fault Protected, 3.3V to 5V, ±20V Common-Mode Range, RS-485/RS-422
Transceivers with Cable Invert and ±15kV ESD
The ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E,
ISL32458E, and ISL32459E are 3.3V to 5V powered, fault
protected, extended Common-Mode Range (CMR) differential
transceivers for balanced communication. The RS-485 bus
pins (driver outputs and receiver inputs) are protected against
overvoltages up to ±60V, and against ±15kV ESD strikes.
These transceivers operate in environments with
common-mode voltages up to ±20V (exceeds the RS-485
requirement), making this RS-485 family one of the most
robust on the market.
The transmitters are RS-485 compliant with VCC ≥ 4.5V and
deliver a 1.1V differential output voltage into the RS-485
specified 54Ω load even with VCC = 3V. The receiver (Rx) inputs
feature a full fail-safe design that ensures a logic-high Rx output
if the Rx inputs are floating, shorted, or on a terminated but
undriven (idle) bus. The Rx full fail-safe operation is maintained
even when the Rx input polarity is switched (cable invert
function on ISL32457E and ISL32459E).
The ISL32457E and ISL32459E include a cable invert function
that reverses the polarity of the Rx and Tx bus pins in case the
cable is misconnected during installation.
See Table 1 on page 4 for key features and configurations by
device number.
Related Literature
FN7921
Rev.3.00
Feb 14, 2019
Features
• Fault protected RS-485 bus pins . . . . . . . . . . . . . . up to ±60V
• Extended common-mode range. . . . . . . . . . . . . . . . . . . . ±20V
larger than required for RS-485
• ±15kV HBM ESD protection on RS-485 bus pins
• Wide supply range . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 5.5V
• Cable invert pin (ISL32457E and ISL32459E only)
corrects for reversed cable connections while maintaining
Rx full fail-safe functionality
• 1/4 unit load for up to 128 devices on the bus
• High transient overvoltage tolerance. . . . . . . . . . . . . . . . ±80V
• Full fail-safe (open, short, terminated) RS-485 receivers
• Choice of RS-485 data rates . . . . . . . . . . . . . . . . . . up to 20Mbps
• Low quiescent supply current. . . . . . . . . . . . . . . . . . . . . 2.1mA
Applications
• Utility meters and automated meter reading systems
• Air conditioning systems
• Security camera networks
• Building lighting and environmental control systems
• Industrial and process control networks
• ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E,
ISL32458E, and ISL32459E device pages
VOLTAGE (V)
B
VID = ±1V
2Mbps
15
10
5
RO
0
COMMON-MODE RANGE (V)
20
12
0
-7
-20
TIME (200ns/DIV)
FIGURE 1. EXCEPTIONAL ISL32453E RX OPERATES AT >1Mbps
EVEN WITH ±20V COMMON-MODE VOLTAGE
FN7921 Rev.3.00
Feb 14, 2019
20
VCC = 3V
A
STANDARD RS-485
TRANSCEIVER
ISL3245XE
FIGURE 2. TRANSCEIVERS DELIVER SUPERIOR COMMON-MODE
RANGE vs STANDARD RS-485 DEVICES
Page 1 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Typical Operating Circuits
+3.3V
+3.3V
+
14
VCC
2 RO
R
0.1µF
0.1µF
+
14
9 Y VCC
RT
A 12
10 Z
B 11
D
DI 5
3 RE
DE 4
4 DE
RE 3
RT
Z 10
5 DI
11 B
Y 9
D
GND
6, 7
RO 2
R
12 A
GND
6, 7
SOIC PINOUT SHOWN
FIGURE 3. ISL32450E, ISL32453E FULL DUPLEX NETWORK
+3.3V
+3.3V
+
8
0.1µF
0.1µF
VCC
1 RO
8
VCC
R
D
2 RE
B/Z
7
3 DE
A/Y
6
4 DI
+
RT
RT
DI 4
7
B/Z
DE 3
6
A/Y
RE 2
RO 1
R
D
GND
5
GND
5
FIGURE 4. ISL32452E, ISL32455E, ISL32458E HALF DUPLEX NETWORK
+3.3V
+3.3V
+
8
0.1µF
0.1µF
+
8
VCC
VCC
2
INV
1 RO
R
A/Y
6
B/Z
7
RT
RT
7
B/Z
6
A/Y
RO 1
R
DE 3
3 DE
4 DI
D
D
GND
5
THE IC ON THE LEFT HAS THE CABLE CONNECTIONS
SWAPPED, SO THE INV PIN IS STRAPPED HIGH TO
INVERT THE RX AND TX POLARITY
GND
DI 4
INV
2
5
FIGURE 5. ISL32457E, ISL32459E HALF DUPLEX NETWORK USING CABLE INVERT FUNCTION
FN7921 Rev.3.00
Feb 14, 2019
Page 2 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Ordering Information
PART NUMBER
(Notes 2, 3)
PART
MARKING
TEMP. RANGE
(°C)
TAPE AND REEL
(Units) (Note 1)
PACKAGE
(RoHS Compliant)
PKG.
DWG. #
ISL32450EIBZ
ISL32450 EIBZ
-40 to +85
-
14 Ld SOIC
M14.15
ISL32450EIBZ-T
ISL32450 EIBZ
-40 to +85
2.5k
14 Ld SOIC
M14.15
ISL32450EIBZ-T7A
ISL32450 EIBZ
-40 to +85
250
14 Ld SOIC
M14.15
ISL32450EIUZ
2450E
-40 to +85
-
10 Ld MSOP
M10.118
ISL32450EIUZ-T
2450E
-40 to +85
2.5k
10 Ld MSOP
M10.118
ISL32450EIUZ-T7A
2450E
-40 to +85
250
10 Ld MSOP
M10.118
ISL32452EIBZ
32452 EIBZ
-40 to +85
-
8 Ld SOIC
M8.15
ISL32452EIBZ-T
32452 EIBZ
-40 to +85
2.5k
8 Ld SOIC
M8.15
ISL32452EIBZ-T7A
32452 EIBZ
-40 to +85
250
8 Ld SOIC
M8.15
ISL32452EIUZ
2452E
-40 to +85
-
8 Ld MSOP
M8.118
ISL32452EIUZ-T
2452E
-40 to +85
2.5k
8 Ld MSOP
M8.118
ISL32452EIUZ-T7A
2452E
-40 to +85
250
8 Ld MSOP
M8.118
ISL32453EIBZ
ISL32453 EIBZ
-40 to +85
-
14 Ld SOIC
M14.15
ISL32453EIBZ-T
ISL32453 EIBZ
-40 to +85
2.5k
14 Ld SOIC
M14.15
ISL32453EIBZ-T7A
ISL32453 EIBZ
-40 to +85
250
14 Ld SOIC
M14.15
ISL32453EIUZ
2453E
-40 to +85
-
10 Ld MSOP
M10.118
ISL32453EIUZ-T
2453E
-40 to +85
2.5k
10 Ld MSOP
M10.118
ISL32453EIUZ-T7A
2453E
-40 to +85
250
10 Ld MSOP
M10.118
ISL32455EIBZ
32455 EIBZ
-40 to +85
-
8 Ld SOIC
M8.15
ISL32455EIBZ-T
32455 EIBZ
-40 to +85
2.5k
8 Ld SOIC
M8.15
ISL32455EIBZ-T7A
32455 EIBZ
-40 to +85
250
8 Ld SOIC
M8.15
ISL32455EIUZ
2455E
-40 to +85
-
8 Ld MSOP
M8.118
ISL32455EIUZ-T
2455E
-40 to +85
2.5k
8 Ld MSOP
M8.118
ISL32455EIUZ-T7A
2455E
-40 to +85
250
8 Ld MSOP
M8.118
ISL32457EIBZ
32457 EIBZ
-40 to +85
-
8 Ld SOIC
M8.15
ISL32457EIBZ-T
32457 EIBZ
-40 to +85
2.5k
8 Ld SOIC
M8.15
ISL32457EIBZ-T7A
32457 EIBZ
-40 to +85
250
8 Ld SOIC
M8.15
ISL32457EIUZ
2457E
-40 to +85
-
8 Ld MSOP
M8.118
ISL32457EIUZ-T
2457E
-40 to +85
2.5k
8 Ld MSOP
M8.118
ISL32457EIUZ-T7A
2457E
-40 to +85
250
8 Ld MSOP
M8.118
ISL32458EIBZ
32458 EIBZ
-40 to +85
-
8 Ld SOIC
M8.15
ISL32458EIBZ-T
32458 EIBZ
-40 to +85
2.5k
8 Ld SOIC
M8.15
ISL32458EIBZ-T7A
32458 EIBZ
-40 to +85
250
8 Ld SOIC
M8.15
FN7921 Rev.3.00
Feb 14, 2019
Page 3 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Ordering Information (Continued)
PART NUMBER
(Notes 2, 3)
PART
MARKING
TEMP. RANGE
(°C)
TAPE AND REEL
(Units) (Note 1)
PACKAGE
(RoHS Compliant)
PKG.
DWG. #
ISL32459EIBZ
32459 EIBZ
-40 to +85
-
8 Ld SOIC
M8.15
ISL32459EIBZ-T
32459 EIBZ
-40 to +85
2.5k
8 Ld SOIC
M8.15
ISL32459EIBZ-T7A
32459 EIBZ
-40 to +85
250
8 Ld SOIC
M8.15
NOTES:
1. See TB347 for details about reel specifications.
2. These Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate
plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Pb-free products are
MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), see the ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E device pages. For
more information about MSL, see TB363.
TABLE 1. SUMMARY OF FEATURES
PART
NUMBER
HALF/FULL
DUPLEX
DATA RATE
(Mbps)
SLEW-RATE
LIMITED?
ISL32450E
Full
0.25
Yes
ISL32452E
Half
0.25
Yes
ISL32453E
Full
1
Yes
ISL32455E
Half
1
Yes
ISL32457E
Half
0.25
Yes
CABLE INVERT
(INV) PIN?
QUIESCENT ICC
(mA)
LOW POWER
SHUTDOWN?
PIN COUNT
No
No
2.1
Yes
10, 14
Yes
No
No
2.1
Yes
8
Yes
No
No
2.1
Yes
10, 14
Yes
No
No
2.1
Yes
8
Tx Only
No
Yes
2.1
No
8
EN PINS? HOT PLUG
Yes
ISL32458E
Half
20
No
Yes
No
No
2.1
Yes
8
ISL32459E
Half
20
No
Tx Only
No
Yes
2.1
No
8
Pin Configurations
ISL32450E, ISL32453E
(14 LD SOIC)
TOP VIEW
NC 1
RO 2
R
RE 3
DE 4
DI 5
D
14 VCC
RO 1
13 NC
RE 2
12 A
DE 3
11 B
DI 4
10 Z
GND 5
GND 6
9 Y
GND 7
8 NC
ISL32452E, ISL32455E, ISL32458E
(8 LD SOIC, 8 LD MSOP)
TOP VIEW
RO 1
R
RE 2
DE 3
DI 4
D
ISL32450E, ISL32453E
(10 LD MSOP)
TOP VIEW
R
10 VCC
9 A
8 B
D
7 Z
6 Y
ISL32457E, ISL32459E
(8 LD SOIC, 8 LD MSOP)
TOP VIEW
8
VCC
RO 1
8
VCC
7
B/Z
INV 2
7
B/Z
6
A/Y
DE 3
6
A/Y
5
GND
DI 4
5
GND
R
D
NOTE: Evaluate creepage and clearance requirements at your maximum fault voltage before using small pitch packages, such as MSOP.
FN7921 Rev.3.00
Feb 14, 2019
Page 4 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Pin Descriptions
PIN
NAME
ISL32452E,
ISL32455E,
ISL32458E
ISL32450E,
ISL32450E,
(8 LD SOIC,
ISL32453E,
ISL32453E,
(14 LD SOIC) (10 LD MSOP) 8 LD MSOP)
PIN #
PIN #
PIN #
ISL32457E,
ISL32459E
(8 LD SOIC,
8 LD MSOP)
PIN #
FUNCTION
RO
2
1
1
1
Receiver output. For parts without the cable invert function - or if INV is low - then:
If A - B ≥ -10mV, RO is high; if A - B ≤ -200mV, RO is low. If INV is high, then: If B A ≥ -10mV, RO is high; if B - A ≤ -200mV, RO is low. In all cases, RO = High if A and
B are unconnected (floating), or shorted together, or connected to an undriven,
terminated bus (that is, Rx is always fail-safe open, shorted and idle, even if
polarity is inverted).
RE
3
2
2
N/A
Receiver output enable. RO is enabled when RE is low; RO is high impedance
when RE is high. Internally pulled low.
DE
4
3
3
3
Driver output enable. The driver outputs, Y and Z, are enabled by bringing DE
high and they are high impedance when DE is low. Internally pulled high.
DI
5
4
4
4
Driver input. For parts without the cable invert function - or if INV is low - a low on
DI forces output Y low and output Z high, while a high on DI forces output Y high
and output Z low. The output states, relative to DI, invert if INV is high.
GND
6, 7
5
5
5
Ground connection.
A/Y
N/A
N/A
6
6
±60V fault protected and ±16.5kV ESD protected RS-485/RS-422 I/O pin. For
parts without the cable invert function - or if INV is low - A/Y is the noninverting
receiver input and noninverting driver output. If INV is high, A/Y is the inverting
receiver input and the inverting driver output. Pin is an input if DE = 0; pin is an
output if DE = 1.
B/Z
N/A
N/A
7
7
±60V fault protected and ±16.5kV ESD protected RS-485/RS-422 I/O pin. For
parts without the cable invert function - or if INV is low - B/Z is the inverting
receiver input and inverting driver output. If INV is high, B/Z is the noninverting
receiver input and the noninverting driver output. Pin is an input if DE = 0; pin
is an output if DE = 1.
A
12
9
N/A
N/A
±60V fault protected and ±15kV ESD protected RS-485/RS-422 noninverting
receiver input.
B
11
8
N/A
N/A
±60V fault protected and ±15kV ESD protected RS-485/RS-422 inverting
receiver input.
Y
9
6
N/A
N/A
±60V fault protected and ±15kV ESD protected RS-485/RS-422 noninverting
driver output.
Z
10
7
N/A
N/A
±60V fault protected and ±15kV ESD protected RS-485/RS-422 inverting driver
output.
VCC
14
10
8
8
System power supply input (3V to 5.5V).
INV
N/A
N/A
N/A
2
Receiver and driver cable invert (polarity selection) input. When driven high this
pin swaps the polarity of the driver output and receiver input pins. If
unconnected (floating) or connected low, normal RS-485 polarity conventions
apply. Internally pulled low.
NC
1, 8, 13
N/A
N/A
N/A
FN7921 Rev.3.00
Feb 14, 2019
No internal connection.
Page 5 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Truth Tables
RECEIVING
TRANSMITTING
INPUTS
INPUTS
OUTPUTS
RE
DE
DI
INV (Note 4)
Y
Z
X
1
1
0
1
0
X
1
0
0
0
1
X
1
1
1
0
1
X
1
0
1
1
0
0
0
X
X
High-Z
High-Z
1
0
X
X
High-Z
(Note 5)
High-Z
(Note 5)
NOTES:
RE
(Note 19)
DE
DE
Full
Half
Duplex Duplex
FN7921 Rev.3.00
Feb 14, 2019
A-B
INV
(Note 4)
RO
0
0
X
VAB ≥ -0.01V
0
1
0
0
X
-0.01V > VAB > -0.2V
0
Undetermined
0
0
X
VAB ≤ -0.2V
0
0
0
0
X
VAB ≤ 0.01V
1
1
0
0
X
0.01V < VAB < 0.2V
1
Undetermined
0
0
X
≥ 0.2V
1
0
0
0
X
Inputs
Open or
Shorted
X
1
1
0
0
X
X
High-Z
(Note 5)
1
1
1
X
X
High-Z
4. Parts without the INV pin follow the rows with INV = “0” and “X”.
5. Low Power Shutdown mode (see Notes 14 and 19).
OUTPUT
Page 6 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Absolute Maximum Ratings
Thermal Information
VCC to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI, DE, RE, INV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
Input/Output Voltages
A/Y, B/Z, A, B, Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60V
A/Y, B/Z, A, B, Y, Z
(Transient Pulse Through 100Ω, Note 6) . . . . . . . . . . . . . . . . . . . ±80V
RO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (VCC +0.3V)
Short-Circuit Duration
Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
ESD Rating . . . . . . . . . . . . . . . . . . . . see “ESD PERFORMANCE” on page 8
Latch-Up (per JESD78, Level 2, Class A) . . . . . . . . . . . . . . . . . . . . . +125°C
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
8 Ld SOIC Package (Notes 7, 8) . . . . . . . . . .
108
47
8 Ld MSOP Package (Notes 7, 8) . . . . . . . . .
140
40
10 Ld MSOP Package (Notes 7, 8) . . . . . . . .
135
50
14 Ld SOIC Package (Notes 7, 8) . . . . . . . . .
88
39
Maximum Junction Temperature (Plastic Package). . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
Recommended Operating Conditions
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3V or 5V
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Bus Pin Common-Mode Voltage Range. . . . . . . . . . . . . . . . . . -20V to +20V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions can adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
6. Tested according to TIA/EIA-485-A, Section 4.2.6 (±80V for 15µs at a 1% duty cycle).
7. θJA is measured with the component mounted on a high-effective thermal conductivity test board in free air. See TB379 for details.
8. For θJC, the “case temp” location is taken at the package top center.
Electrical Specifications Test Conditions: VCC = 3V to 3.6V and 4.5V to 5.5V, unless otherwise specified. Typicals are at the worst case of
VCC = 5V or VCC = 3.3V, TA = +25°C (Note 9). Boldface limits apply across the operating temperature range, -40°C to +85°C.
PARAMETER
TEMP
(°C)
MIN
(Note 17)
TYP
MAX
(Note 17)
UNIT
Full
-
-
VCC
V
RL = 100Ω (RS-422), VCC ≥ 4.5V
Full
2
3
-
V
RL = 54Ω (RS-485)
VCC ≥ 4.5V
Full
1.7
2.3
VCC
V
VCC ≥ 3V
Full
1.1
1.3
VCC
V
SYMBOL
TEST CONDITIONS
DC CHARACTERISTICS
Driver Differential VOUT (No load)
VOD1
Driver Differential VOUT (Loaded,
Figure 6A)
VOD2
Change in Magnitude of Driver
Differential VOUT for Complementary
Output States
ΔVOD
RL = 54Ω or 100Ω (Figure 6A)
Full
-
-
0.2
V
Driver Differential VOUT with
Common-Mode Load (Figure 6B)
VOD3
RL = 60Ω, -20V ≤ VCM ≤ 20V, VCC ≥ 4.5V
Full
1.5
-
-
V
Driver Common-Mode VOUT
(Figure 6A)
VOC
RL = 54Ω or 100Ω
Full
-1
-
3
V
Change in Magnitude of Driver
Common-Mode VOUT for
Complementary Output States
ΔVOC
RL = 54Ω or 100Ω (Figure 6A)
Full
-
-
0.2
V
Driver Short-Circuit Current
IOSD
DE = VCC, -20V ≤ VO ≤ 20V (Note 11)
Full
-250
-
250
mA
IOSD1
At first foldback, 24V ≤ VO ≤ -24V
Full
-83
-
83
mA
IOSD2
At second foldback, 35V ≤ VO ≤ -35V
Full
-13
-
13
mA
Logic Input High Voltage
VIH
DE, DI, RE, INV (See Figure 33)
Full
2.35
-
-
V
Logic Input Low Voltage
VIL
DE, DI, RE, INV
Full
-
-
0.8
V
Logic Input Current
IIN1
DI
Full
-1
-
1
µA
DE, RE, INV
Full
-15
6
15
µA
FN7921 Rev.3.00
Feb 14, 2019
Page 7 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Electrical Specifications Test Conditions: VCC = 3V to 3.6V and 4.5V to 5.5V, unless otherwise specified. Typicals are at the worst case of
VCC = 5V or VCC = 3.3V, TA = +25°C (Note 9). Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
PARAMETER
Input/Output Current (A/Y, B/Z)
Input Current (A, B)
(Full Duplex Versions Only)
Output Leakage Current (Y, Z)
(Full Duplex Versions Only)
TEMP
(°C)
MIN
(Note 17)
TYP
MAX
(Note 17)
UNIT
Full
-
-
250
µA
Full
-200
-
-
µA
VIN = ±20V
Full
-800
-
850
µA
VIN = ±60V, (Note 18)
Full
-6
-
6
mA
VIN = 12V
Full
-
-
125
µA
VIN = -7V
Full
-100
-
-
µA
VIN = ±20V
Full
-500
-
500
µA
VIN = ±60V, (Note 18)
Full
-3
-
3
mA
VIN = 12V
Full
-
-
200
µA
VIN = -7V
Full
-100
-
-
µA
VIN = ±20V
Full
-500
-
500
µA
VIN = ±60V, (Note 18)
Full
-3
-
3
mA
VCC ≤ 3.6V
-20V ≤ VCM ≤ 20V,
(For ISL32457E and
ISL32459E only, A-B VCC ≥ 4.5V
if INV = 0; B-A if
INV = 1)
Full
-200
-120
-10
mV
Full
-250
-180
-10
mV
+25
-
30
-
mV
IO = -4mA, VCC ≥ 3V
Full
2.4
-
-
V
IO = -8mA, VCC ≥ 4.5V
Full
2.4
-
-
V
IO = 4mA, VCC ≥ 3V, VID = -200mV
Full
-
-
0.4
V
IO = 5mA, VCC ≥ 4.5V, VID = -250mV
Full
-
-
0.4
V
SYMBOL
IIN2
IIN3
IOZD
TEST CONDITIONS
DE = 0V, VCC = 0V or VIN = 12V
3.6V or 5.5V
VIN = -7V
VCC = 0V or 3.6V or
5.5V
RE = 0V, DE = 0V,
VCC = 0V or 3.6V or
5.5V
Receiver Differential Threshold
Voltage
VTH
Receiver Input Hysteresis
ΔVTH
-20V ≤ VCM ≤ 20V
Receiver Output High Voltage
VOH1
VID = -10mV
VOH2
Receiver Output Low Voltage
VOL
Three-State (High Impedance)
Receiver Output Current (Note 19)
IOZR
0V ≤ VO ≤ VCC
Full
-1
0.01
1
µA
Receiver Short-Circuit Current
IOSR
0V ≤ VO ≤ VCC
Full
-
-
±115
mA
DE = VCC, RE = 0V or VCC, DI = 0V or VCC
Full
-
2.1
4.5
mA
DE = 0V, RE = VCC, DI = 0V or VCC
Full
-
10
35
µA
Human Body Model
(ISL32450E, ISL32452E, ISL32453E,
ISL32455E, ISL32457E; Tested per
JESD22-A114E)
+25
-
±8
-
kV
Human Body Model
(ISL32458E, ISL32459E; Tested per
JESD22-A114E)
+25
-
±3
-
kV
Machine Model
(Tested per JESD22-A115-A)
+25
-
±700
-
V
Human Body Model, Full Duplex
from Bus Pins to GND
Half Duplex
+25
-
±15
-
kV
+25
-
±16.5
-
kV
SUPPLY CURRENT
No-Load Supply Current (Note 10)
Shutdown Supply Current (Note 19)
ICC
ISHDN
ESD PERFORMANCE
All Pins
RS-485 Pins (A, B, Y, Z,
A/Y, B/Z)
FN7921 Rev.3.00
Feb 14, 2019
Page 8 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Electrical Specifications Test Conditions: VCC = 3V to 3.6V and 4.5V to 5.5V, unless otherwise specified. Typicals are at the worst case of
VCC = 5V or VCC = 3.3V, TA = +25°C (Note 9). Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
(Note 17)
TYP
MAX
(Note 17)
UNIT
DRIVER SWITCHING CHARACTERISTICS (250kbps VERSIONS; ISL32450E, ISL32452E, ISL32457E)
Driver Differential Output Delay
tPLH, tPHL
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
280
1000
ns
Driver Differential Output Skew
tSKEW
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
4
100
ns
Driver Differential Rise or Fall Time
tR, tF
RD = 54Ω, CD = 50pF (Figure 7)
Full
250
650
1500
ns
Maximum Data Rate
fMAX
CD = 820pF (Figure 9)
Full
250
-
-
kbps
Driver Enable to Output High
tZH
SW = GND (Figure 8), (Note 12)
Full
-
-
1600
ns
Driver Enable to Output Low
tZL
SW = VCC (Figure 8), (Note 12)
Full
-
-
1600
ns
Driver Disable from Output Low
tLZ
SW = VCC (Figure 8)
Full
-
-
300
ns
Driver Disable from Output High
tHZ
SW = GND (Figure 8)
Full
-
-
300
ns
(Notes 14, 19)
Full
60
160
600
ns
Time to Shutdown
tSHDN
Driver Enable from Shutdown to
Output High
tZH(SHDN)
SW = GND (Figure 8), (Notes 14, 15, 19)
Full
-
-
3000
ns
Driver Enable from Shutdown to
Output Low
tZL(SHDN)
SW = VCC (Figure 8), (Notes 14, 15, 19)
Full
-
-
3000
ns
DRIVER SWITCHING CHARACTERISTICS (1Mbps VERSIONS; ISL32453E, ISL32455E)
Driver Differential Output Delay
tPLH, tPHL
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
70
200
ns
Driver Differential Output Skew
tSKEW
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
4
25
ns
Driver Differential Rise or Fall Time
tR, tF
RD = 54Ω, CD = 50pF (Figure 7)
Full
50
130
300
ns
Maximum Data Rate
fMAX
CD = 820pF (Figure 9)
Full
1
-
-
Mbps
Driver Enable to Output High
tZH
SW = GND (Figure 8), (Note 12)
Full
-
-
300
ns
Driver Enable to Output Low
tZL
SW = VCC (Figure 8), (Note 12)
Full
-
-
300
ns
Driver Disable from Output Low
tLZ
SW = VCC (Figure 8)
Full
-
-
300
ns
Driver Disable from Output High
tHZ
SW = GND (Figure 8)
Full
-
-
300
ns
(Note 14)
Full
60
160
600
ns
Time to Shutdown
tSHDN
Driver Enable from Shutdown to
Output High
tZH(SHDN)
SW = GND (Figure 8), (Notes 14, 15)
Full
-
-
3000
ns
Driver Enable from Shutdown to
Output Low
tZL(SHDN)
SW = VCC (Figure 8), (Notes 14, 15)
Full
-
-
3000
ns
DRIVER SWITCHING CHARACTERISTICS (20Mbps VERSIONS; ISL32458E, ISL32459E)
Driver Differential Output Delay
tPLH, tPHL
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
28
45
ns
Driver Differential Output Skew
tSKEW
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
3
9
ns
Driver Differential Rise or Fall Time
tR, tF
RD = 54Ω, CD = 50pF (Figure 7)
Full
-
17
35
ns
Maximum Data Rate
fMAX
CD = 470pF (Figure 9)
Full
20
-
-
Mbps
Driver Enable to Output High
tZH
SW = GND (Figure 8), (Note 12)
Full
-
-
180
ns
Driver Enable to Output Low
tZL
SW = VCC (Figure 8), (Note 12)
Full
-
-
180
ns
Driver Disable from Output Low
tLZ
SW = VCC (Figure 8)
Full
-
-
300
ns
Driver Disable from Output High
tHZ
SW = GND (Figure 8)
Full
-
-
300
ns
(Notes 14, 19)
Full
60
160
600
ns
SW = GND (Figure 8), (Notes 14, 15, 19)
Full
-
-
3000
ns
Time to Shutdown
Driver Enable from Shutdown to
Output High
FN7921 Rev.3.00
Feb 14, 2019
tSHDN
tZH(SHDN)
Page 9 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Electrical Specifications Test Conditions: VCC = 3V to 3.6V and 4.5V to 5.5V, unless otherwise specified. Typicals are at the worst case of
VCC = 5V or VCC = 3.3V, TA = +25°C (Note 9). Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
PARAMETER
Driver Enable from Shutdown to
Output Low
SYMBOL
tZL(SHDN)
TEST CONDITIONS
SW = VCC (Figure 8), (Notes 14, 15, 19)
TEMP
(°C)
MIN
(Note 17)
TYP
MAX
(Note 17)
UNIT
Full
-
-
3000
ns
RECEIVER SWITCHING CHARACTERISTICS (250kbps VERSIONS; ISL32450E, ISL32452E, ISL32457E)
Maximum Data Rate
Receiver Input to Output Delay
Receiver Skew |tPLH - tPHL |
fMAX
(Figure 10)
Full
250
-
-
kbps
tPLH, tPHL
(Figure 10)
Full
-
240
325
ns
tSKD
(Figure 10)
Full
-
6
25
ns
Receiver Enable to Output Low
tZL
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Notes 13, 19)
Full
-
-
80
ns
Receiver Enable to Output High
tZH
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Notes 13, 19)
Full
-
-
80
ns
Receiver Disable from Output Low
tLZ
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Note 19)
Full
-
-
80
ns
Receiver Disable from Output High
tHZ
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Note 19)
Full
-
-
80
ns
(Notes 14, 19)
Full
60
160
600
ns
Time to Shutdown
tSHDN
Receiver Enable from Shutdown to
Output High
tZH(SHDN)
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Notes 14, 16, 19)
Full
-
-
2500
ns
Receiver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Notes 14, 16, 19)
Full
-
-
2500
ns
RECEIVER SWITCHING CHARACTERISTICS (1Mbps VERSIONS; ISL32453E, ISL32455E)
Maximum Data Rate
Receiver Input to Output Delay
Receiver Skew |tPLH - tPHL |
fMAX
(Figure 10)
Full
1
-
-
Mbps
tPLH, tPHL
(Figure 10)
Full
-
115
200
ns
tSKD
(Figure 10)
Full
-
4
20
ns
Receiver Enable to Output Low
tZL
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Note 13)
Full
-
-
80
ns
Receiver Enable to Output High
tZH
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Note 13)
Full
-
-
80
ns
Receiver Disable from Output Low
tLZ
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11)
Full
-
-
80
ns
Receiver Disable from Output High
tHZ
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11)
Full
-
-
80
ns
(Note 14)
Full
60
160
600
ns
Time to Shutdown
tSHDN
Receiver Enable from Shutdown to
Output High
tZH(SHDN)
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Notes 14, 16)
Full
-
-
2500
ns
Receiver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Notes 14, 16)
Full
-
-
2500
ns
RECEIVER SWITCHING CHARACTERISTICS (20Mbps VERSIONS; ISL32458E, ISL32459E)
Maximum Data Rate
Receiver Input to Output Delay
Receiver Skew |tPLH - tPHL |
fMAX
(Figure 10)
Full
20
-
-
Mbps
tPLH, tPHL
(Figure 10)
Full
-
40
80
ns
tSKD
(Figure 10)
Full
-
3
9
ns
Receiver Enable to Output Low
tZL
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Notes 13, 19)
Full
-
-
80
ns
Receiver Enable to Output High
tZH
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Notes 13, 19)
Full
-
-
80
ns
Receiver Disable from Output Low
tLZ
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Note 19)
Full
-
-
80
ns
FN7921 Rev.3.00
Feb 14, 2019
Page 10 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Electrical Specifications Test Conditions: VCC = 3V to 3.6V and 4.5V to 5.5V, unless otherwise specified. Typicals are at the worst case of
VCC = 5V or VCC = 3.3V, TA = +25°C (Note 9). Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
PARAMETER
TEMP
(°C)
MIN
(Note 17)
TYP
MAX
(Note 17)
UNIT
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Note 19)
Full
-
-
80
ns
(Notes 14, 19)
Full
60
160
600
ns
SYMBOL
Receiver Disable from Output High
Time to Shutdown
tHZ
tSHDN
TEST CONDITIONS
Receiver Enable from Shutdown to
Output High
tZH(SHDN)
RL = 1kΩ, CL = 15pF, SW = GND (Figure 11),
(Notes 14, 16, 19)
Full
-
-
2500
ns
Receiver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 11),
(Notes 14, 16, 19)
Full
-
-
2500
ns
NOTES:
9. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise
specified.
10. Supply current specification is valid for loaded drivers when DE = 0V.
11. Applies to peak current. See “Typical Performance Curves” beginning on page 13 for more information.
12. Keep RE = 0 to prevent the device from entering shutdown (does not apply to the ISL32457E and ISL32459E).
13. The RE signal high time must be short enough (typically 600ns to ensure that the device enters shutdown.
16. Set the RE signal high time >600ns to ensure that the device enters shutdown.
17. Compliance to data sheet limits is assured by one or more methods: production test, characterization and/or design.
18. See “Caution” statement following “Absolute Maximum Ratings” on page 7.
19. Does not apply to the ISL32457E and ISL32459E. These transceivers have no Rx enable function, and thus no shutdown function.
Test Circuits and Waveforms
VCC
RL/2
DE
DI
VCC
Z
DI
VOD
D
Y
375Ω
Z
VCM
VOD
D
Y
RL/2
FIGURE 6A. VOD AND VOC
RL/2
DE
VOC
RL/2
375Ω
FIGURE 6B. VOD WITH COMMON-MODE LOAD
FIGURE 6. DC DRIVER TEST CIRCUITS
FN7921 Rev.3.00
Feb 14, 2019
Page 11 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Test Circuits and Waveforms (Continued)
3V
DI
50%
50%
0V
VCC
DE
tPHL
tPLH
Z
DI
RD
CD
D
Y
OUT (Z)
VOH
OUT (Y)
VOL
SIGNAL
GENERATOR
90%
DIFF OUT (Y - Z)
+VOD
90%
10%
10%
tR
-VOD
tF
SKEW = |tPLH - tPHL|
FIGURE 7A. TEST CIRCUIT
FIGURE 7B. MEASUREMENT POINTS
FIGURE 7. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES
DE
Z
DI
110Ω
VCC
D
SIGNAL
GENERATOR
SW
Y
GND
3V
DE
Note 14
CL
tZH, tZH(SHDN)
Note 14
PARAMETER
OUTPUT
RE
DI
SW
CL (pF)
tHZ
Y/Z
X
1/0
GND
50
tLZ
Y/Z
X
0/1
VCC
50
tZH
Y/Z
tZL
Y/Z
0 (Note 12)
0 (Note 12)
1/0
GND
0/1
VCC
100
100
tZH(SHDN)
Y/Z
1 (Note 15)
1/0
GND
100
tZL(SHDN)
Y/Z
1 (Note 15)
0/1
VCC
100
50%
50%
0V
tHZ
OUTPUT HIGH
VOH
VOH - 0.5V
50%
OUT (Y, Z)
0V
tZL, tZL(SHDN)
tLZ
Note 14
VCC
OUT (Y, Z)
50%
VOL + 0.5V
VOL
OUTPUT LOW
FIGURE 8B. MEASUREMENT POINTS
FIGURE 8A. TEST CIRCUIT
FIGURE 8. DRIVER ENABLE AND DISABLE TIMES
VCC
3V
DE
+
Z
DI
54Ω
D
Y
SIGNAL
GENERATOR
CD
DI
0V
VOD
-
+VOD
DIFF OUT (Y - Z)
-VOD
0V
FIGURE 9B. MEASUREMENT POINTS
FIGURE 9A. TEST CIRCUIT
FIGURE 9. DRIVER DATA RATE
FN7921 Rev.3.00
Feb 14, 2019
Page 12 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Test Circuits and Waveforms (Continued)
RE
B
B
R
A
SIGNAL
GENERATOR
+2.25V
15pF
RO
1.5V
1.5V
+750mV
A
tPLH
SIGNAL
GENERATOR
tPHL
VCC
50%
RO
50%
+1.5V
0V
FIGURE 10A. TEST CIRCUIT
FIGURE 10B. MEASUREMENT POINTS
FIGURE 10. RECEIVER PROPAGATION DELAY AND DATA RATE
RE
B
A
R
VCC
1kΩ
RO
SIGNAL
GENERATOR
15pF
Note 14
GND
SW
RE
3V
50%
50%
0V
PARAMETER
DE
A
SW
tHZ
0
+1.5V
GND
tLZ
0
-1.5V
VCC
tZH (Note 13)
0
+1.5V
GND
tZL (Note 13)
0
tZH(SHDN) (Note 16)
0
tZL(SHDN) (Note 16)
-1.5V
VOH - 0.5V
1.5V
VOH
0V
tZL, tZL(SHDN)
tLZ
Note 14
VCC
RO
GND
-1.5V
tHZ
OUTPUT HIGH
RO
VCC
+1.5V
0
tZH, tZH(SHDN)
Note 14
1.5V
VOL + 0.5V
VOL
OUTPUT LOW
VCC
FIGURE 11B. MEASUREMENT POINTS
FIGURE 11A. TEST CIRCUIT
FIGURE 11. RECEIVER ENABLE AND DISABLE TIMES
Typical Performance Curves
RD = 20Ω
70
RD = 30Ω
+25°C
60
DIFFERENTIAL OUTPUT VOLTAGE (V)
3.25
80
DRIVER OUTPUT CURRENT (mA)
TA = +25°C; unless otherwise specified.
RD = 54Ω
+85°C
+25°C
50
40
+85°C
RD = 100Ω
30
20
VCC = 5V
10
0
VCC = 3.3V
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
DIFFERENTIAL OUTPUT VOLTAGE (V)
FIGURE 12. DRIVER OUTPUT CURRENT vs DIFFERENTIAL OUTPUT
VOLTAGE
FN7921 Rev.3.00
Feb 14, 2019
VCC = 5V
3.00
2.75
RD = 100Ω
VCC = 5V
2.50
RD = 54Ω
2.25
2.00
1.75
RD = 100Ω
VCC = 3.3V
RD = 54Ω
1.50
1.25
-40 -30 -20 -10
VCC = 3.3V
0
10
20
30
40
50
60
70
80 85
TEMPERATURE (°C)
FIGURE 13. DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs
TEMPERATURE
Page 13 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Typical Performance Curves
TA = +25°C; unless otherwise specified. (Continued)
2.2
80
VOL, +25°C
2.1
VCC = 5V
2.0
DE = GND, RE = GND
ICC (mA)
1.9
VCC = 5V
1.8
DE = VCC, RE = X
1.7
VCC = 3.3V
1.6
DE = GND, RE = GND
1.5
VCC = 3.3V
1.4
-40 -30 -20 -10
0
10
20
30
40
50
60
70
RECEIVER OUTPUT CURRENT (mA)
DE = VCC, RE = X
VCC = 5V
60
VOL, +85°C
VOL, +25°C
VCC = 3.3V
40
VOL, +85°C
20
VCC = 3.3V
0
VOH, +85°C
-20
-40
VOH, +25°C
-60
80 85
0
0.5
1.0
TEMPERATURE (°C)
1000
150
VCC = 0V TO 5.5V
125
800
100
600
OUTPUT CURRENT (mA)
BUS PIN CURRENT (µA)
1.5 2.0
2.5 3.0
3.5 4.0
RECEIVER OUTPUT VOLTAGE (V)
400
200
Y OR Z
-200
25
0
-25
-50
VCC = 3.3V, +25°C
Y OR Z = HIGH
30
40
50
60
5
tPLH
260
250
240
tPLH
VCC = 5V
4
3
2
VCC = 3.3V
VCC = 5V
tPHL
1
210
|tPLH - tPHL|
0
10
20
30
40
50
60
70
80 85
TEMPERATURE (°C)
FIGURE 18. DRIVER DIFFERENTIAL PROPAGATION DELAY vs
TEMPERATURE (ISL32450E, ISL32452E, ISL32457E)
FN7921 Rev.3.00
Feb 14, 2019
20
6
SKEW (ns)
PROPAGATION DELAY (ns)
270
200
-40 -30 -20 -10
10
7
tPHL
VCC = 3.3V
220
0
FIGURE 17. DRIVER OUTPUT CURRENT vs SHORT-CIRCUIT VOLTAGE
RD = 54Ω, CD = 50pF
230
VCC = 5V, +25°C
OUTPUT VOLTAGE (V)
FIGURE 16. BUS PIN CURRENT vs BUS PIN VOLTAGE
280
VCC = 3.3V, +85°C
VCC = 5V, +85°C
BUS PIN VOLTAGE (V)
290
VCC = 5V, +85°C
VCC = 3.3V, +85°C
Y OR Z = LOW
-125
-60 -50 -40 -30 -20 -10
10 20 30 40 50 60 70
300
5.0
50
-100
A/Y OR B/Z
VCC = 5V, +25°C
VCC = 3.3V, +25°C
75
-75
-400
-600
-70 -60 -50 -40 -30 -20 -10 0
4.5
FIGURE 15. RECEIVER OUTPUT CURRENT vs RECEIVER OUTPUT
VOLTAGE
FIGURE 14. SUPPLY CURRENT vs TEMPERATURE
0
VCC = 5V
VOH, +25°C
VOH, +85°C
0
-40 -30 -20 -10
0
10 20 30 40 50
TEMPERATURE (°C)
60
70
80 85
FIGURE 19. DRIVER DIFFERENTIAL SKEW vs TEMPERATURE
(ISL32450E, ISL32452E, ISL32457E)
Page 14 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Typical Performance Curves
70
4.5
RD = 54Ω, CD = 50pF
tPLH
VCC = 3.3V
4.0
VCC = 5V
3.5
tPHL
3.0
65
SKEW (ns)
PROPAGATION DELAY (ns)
75
TA = +25°C; unless otherwise specified. (Continued)
60
tPHL
10
VCC = 3.3V
1.0
VCC = 5V
55
0
2.0
1.5
tPLH
50
-40 -30 -20 -10
2.5
0.5
20
30
40
50
60
70
|tPLH - tPHL|
0
-40 -30 -20 -10
80 85
0
TEMPERATURE (°C)
tPHL
VCC = 5V
tPHL
10
0
10
20
30
40
50
60
70
2.0
VCC = 3.3V
1.5
|tPLH - tPHL|
0
-40 -30 -20 -10
80 85
15
10
10
5
VCC = 3.3V
VCC = 5V
RO
VCC = 3.3V
0
5
0
-5
-5
-10
-10
-15
A
-20
B
TIME (1µs/DIV)
FIGURE 24. ±20V RECEIVER PERFORMANCE (ISL32450E,
ISL32452E, ISL32457E)
FN7921 Rev.3.00
Feb 14, 2019
30
40
50
B
15
VOLTAGE (V)
VOLTAGE (V)
VID = ±1V
250kbps
VCC = 5V
RO
20
60
70
80 85
A
20
B
10
FIGURE 23. DRIVER DIFFERENTIAL SKEW vs TEMPERATURE
(ISL32458E, ISL32459E)
A
20
0
TEMPERATURE (°C)
FIGURE 22. DRIVER DIFFERENTIAL PROPAGATION DELAY vs
TEMPERATURE (ISL32458E, ISL32459E)
-20
80 85
2.5
TEMPERATURE (°C)
-15
70
0.5
0
-40 -30 -20 -10
0
60
1.0
5
5
50
VCC = 5V
3.0
tPLH
SKEW (ns)
PROPAGATION DELAY (ns)
VCC = 3.3V
15
0
40
3.5
tPLH
20
5
30
4.0
RD = 54Ω, CD = 50pF
30
25
20
FIGURE 21. DRIVER DIFFERENTIAL SKEW vs TEMPERATURE
(ISL32453E, ISL32455E)
FIGURE 20. DRIVER DIFFERENTIAL PROPAGATION DELAY vs
TEMPERATURE (ISL32453E, ISL32455E)
35
10
TEMPERATURE (°C)
VID = ±1V
1Mbps
VCC = 5V
RO
VCC = 3.3V
VCC = 5V
RO
VCC = 3.3V
A
B
TIME (400ns/DIV)
FIGURE 25. ±20V RECEIVER PERFORMANCE (ISL32453E,
ISL32455E)
Page 15 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
10
VCC = 5V
5
RO
0
VCC = 3.3V
RO
0
DRIVER OUTPUT (V)
VCC = 5V
5
VCC = 3.3V
-5
-10
-15
A
-20
B
RD = 54Ω, CD = 50pF
3
DI
0
3
RO
0
2
1
0
A/Y - B/Z
-1
-2
TIME (1µs/DIV)
TIME (20ns/DIV)
3
DI
0
3
RO
0
2
1
0
RECEIVER OUTPUT (V)
RD = 54Ω, CD = 50pF
DRIVER INPUT (V)
FIGURE 27. VCC = 3.3V, DRIVER AND RECEIVER WAVEFORMS
(ISL32450E, ISL32452E, ISL32457E)
DRIVER OUTPUT (V)
DRIVER OUTPUT (V)
RECEIVER OUTPUT (V)
FIGURE 26. ±20V RECEIVER PERFORMANCE (ISL32458E,
ISL32459E)
A/Y - B/Z
-1
-2
RD = 54Ω, CD = 50pF
3
DI
0
3
RO
0
2
1
0
A/Y - B/Z
-1
-2
TIME (400ns/DIV)
TIME (20ns/DIV)
0
5
0
3
2
1
0
-1
-2
-3
RO
A/Y - B/Z
TIME (1µs/DIV)
FIGURE 30. VCC = 5V, DRIVER AND RECEIVER WAVEFORMS
(ISL32450E, ISL32452E, ISL32457E)
FN7921 Rev.3.00
Feb 14, 2019
RECEIVER OUTPUT (V)
5
DRIVER INPUT (V)
RD = 54Ω, CD = 50pF
FIGURE 29. VCC = 3.3V, DRIVER AND RECEIVER WAVEFORMS
(ISL32458E, ISL32459E)
DRIVER OUTPUT (V)
DRIVER OUTPUT (V)
RECEIVER OUTPUT (V)
FIGURE 28. VCC = 3.3V, DRIVER AND RECEIVER WAVEFORMS
(ISL32453E, ISL32455E)
DI
DRIVER INPUT (V)
15
VID = ±1V
20Mbps
RD = 54Ω, CD = 50pF
DI
5
0
5
0
3
2
1
0
-1
-2
-3
RO
DRIVER INPUT (V)
B
DRIVER INPUT (V)
A
20
VOLTAGE (V)
TA = +25°C; unless otherwise specified. (Continued)
RECEIVER OUTPUT (V)
Typical Performance Curves
A/Y - B/Z
TIME (400ns/DIV)
FIGURE 31. VCC = 5V, DRIVER AND RECEIVER WAVEFORMS
(ISL32453E, ISL32455E)
Page 16 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
DI
2.4
5
0
5
0
RO
3
2
1
0
-1
DRIVER INPUT (V)
RD = 54Ω, CD = 50pF
TA = +25°C; unless otherwise specified. (Continued)
2.2
INPUT HIGH VOLTAGE (V)
DRIVER OUTPUT (V)
RECEIVER OUTPUT (V)
Typical Performance Curves
VCC = 5V
2.0
1.8
1.6
VCC = 3.3V
1.4
1.2
A/Y - B/Z
1.0
-40 -30 -20 -10
-2
-3
TIME (20ns/DIV)
FIGURE 32. VCC = 5V, DRIVER AND RECEIVER WAVEFORMS
(ISL32458E, ISL32459E)
FN7921 Rev.3.00
Feb 14, 2019
0
10
20
30
40
50
60
70
80 85
TEMPERATURE (°C)
FIGURE 33. LOGIC INPUT HIGH VOLTAGE vs TEMPERATURE
Page 17 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Application Information
RS-485 and RS-422 are differential (balanced) data
transmission standards used for long haul or noisy environments.
RS-422 is a subset of RS-485, so RS-485 transceivers are also
RS-422 compliant. RS-422 is a point-to-multipoint (multidrop)
standard that allows only one driver and up to 10 receivers
(assuming one unit load devices) on each bus. RS-485 is a true
multipoint standard that allows up to 32 one unit load devices
(any combination of drivers and receivers) on each bus. To allow
for multipoint operation, the RS-485 specification requires that
drivers must handle bus contention without sustaining any
damage.
Driver (Tx) Features
The RS-485/RS-422 driver is a differential output device that
delivers at least 1.7V across a 54Ω load (RS-485), and at least 2V
across a 100Ω load (RS-422) with VCC ≥ 4.5V. The drivers feature
low propagation delay skew to maximize bit width and to
minimize EMI. All drivers are tri-statable through the active high
DE input.
The 250kbps and 1Mbps driver outputs are slew rate limited to
minimize EMI and reflections in unterminated or improperly
terminated networks. The ISL32458E and ISL32459E driver
outputs are not limited, so faster output transition times allow data
rates of at least 20Mbps.
An important advantage of RS-485 is the extended
Common-Mode Range (CMR), which specifies that the driver
outputs and receiver inputs withstand signals that range from
+12V to -7V. RS-422 and RS-485 are intended for runs as long as
4000ft, so the wide CMR is necessary to handle ground potential
differences and voltages induced in the cable by external fields.
High Overvoltage (Fault) Protection
Increases Ruggedness
The ISL3245xE are a family of ruggedized RS-485 transceivers
that improve on the RS-485 basic requirements and increases
system reliability. The CMR increases to ±20V that the RS-485
bus pins (receiver inputs and driver outputs) include fault
protection against voltages and transients up to ±60V.
Additionally, the ±15kV to ±16.5kV built-in ESD protection
complements the fault protection.
These devices use a differential input receiver for maximum noise
immunity and common-mode rejection. Input sensitivity is better
than ±200mV (3.3V operation), as required by the RS-422 and
RS-485 specifications.
The ±60V fault protection (referenced to the IC GND) on the
RS-485 pins makes these transceivers some of the most rugged
on the market. This level of protection makes the ISL3245xE
family ideal for applications where power (such as 24V and 48V
supplies) must be routed in the conduit with the data lines and
for outdoor applications where large transients are likely to
occur. When power is routed with the data lines, even a
momentary short between the supply and data lines destroys an
unprotected device. The ±60V fault levels of this family are at
least four times higher than the levels specified for standard
RS-485 ICs. The ISL3245xE’s protection is active whether the Tx
is enabled or disabled, and even if the IC is powered down or VCC
and Ground are floating.
The receiver input (load) current surpasses the RS-422
specification of 3mA and is four times lower than the RS-485
Unit Load (UL) requirement of 1mA maximum. Therefore, these
products are known as one-quarter UL transceivers, and there
can be up to 128 of these devices on a network while still
complying with the RS-485 loading specification.
If transients or voltages (including overshoots and ringing)
greater than ±60V are possible, additional external protection is
required. Use a protection device with the lowest clamping
voltage acceptable for the application. Note, TVS type devices
typically clamp 5V to 10V above the designated stand-off voltage
(for example, a “54V TVS” clamps between 60V and 66V).
The receiver (Rx) functions, with common-mode voltages as
great as ±20V, make them ideal for industrial or long networks
where induced voltages are a realistic concern.
Wide Common-Mode Voltage (CMV) Tolerance
Improves Operating Range
Receiver (Rx) Features
All the receivers include a full fail-safe function that ensures a
high level receiver output if the receiver inputs are unconnected
(floating), shorted together, or connected to a terminated bus
with all the transmitters disabled (an idle bus).
Receivers easily meet the data rates supported by the
corresponding driver, and most receiver outputs are tri-statable
using the active low RE input.
The Rx in the 250kbps (ISL32450E, ISL32452E, and ISL32457E)
and 1Mbps (ISL32453E and ISL32455E) versions include noise
filtering circuitry to reject high frequency signals. The ISL32453E
and ISL32455E typically reject pulses narrower than 50ns
(equivalent to 20Mbps), while the ISL32450E, ISL32452E, and
ISL32457E Rx reject pulses below 150ns (6.7Mbps). The
ISL32450E, ISL32452E, and ISL32457E have no Rx noise
filtering.
FN7921 Rev.3.00
Feb 14, 2019
Note: The available smaller pitch package (MSOP) may not meet
the Creepage and Clearance (C&C) requirements for ±60V levels.
Determine C&C requirements before selecting a package type.
RS-485 networks operating in industrial complexes or over long
distances are susceptible to large CMV variations. Either of these
operating environments can suffer from large node-to-node
ground potential differences or CMV pickup from external
electromagnetic sources, and devices with only the minimum
required +12V to -7V CMR can malfunction. The ISL3245xE’s
extended ±20V CMR allows for operation in environments that
would overwhelm lesser transceivers. Additionally, the Rx does
not phase invert (erroneously change state) even with CMVs of
±25V or differential voltages as large as 40V.
Page 18 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Cable Invert (Polarity Reversal) Function
Large node count RS-485 networks are commonly wired
backwards during installation. When this happens, the node is
unable to communicate over the network. When a technician
finds the miswired node, they must then rewire the connector,
which is time consuming.
The ISL32457E and ISL32459E simplify this task by including a
cable invert pin (INV) that allows the technician to invert the
polarity of the Rx input and the Tx output pins simply by moving a
jumper to change the state of the invert pin. When the invert pin
is low, the IC operates like any standard RS-485 transceiver, and
the bus pins have their normal polarity definition of A and Y as
noninverting and B and Z as inverting. With the invert pin high,
the corresponding bus pins reverse their polarity, so B and Z
become noninverting, and A and Y become inverting.
This unique cable invert function is superior to that found on
competing devices, because the Rx full fail-safe function is
maintained, even when the Rx polarity is reversed. Competitor
devices implement the Rx invert function simply by inverting the
Rx output. This means that with the Rx inputs floating or shorted
together, the Rx appropriately delivers a logic 1 in normal
polarity, but outputs a logic low when the IC is operated in the
inverted mode. The innovative Renesas Rx design ensures that
the Rx output remains high with the Rx inputs floating or shorted
together (VID = 0V), regardless of the state of the invert pin.
Data Rate, Cables, and Terminations
RS-485/RS-422 are intended for network lengths up to 4000ft,
but the maximum system data rate decreases as the
transmission length increases. High speed versions operating at
20Mbps can be used at lengths up to 150ft (46m), but the
distance can be increased to 328ft (100m) by operating them at
5Mbps. The ISL32453E and ISL32455E can operate at the full
data rate of 1Mbps with lengths up to 800ft (244m). Jitter is the
limiting parameter at faster data rates and may limit the network
to shorter lengths, so employing encoded data streams (such as
Manchester coded or Return-to-Zero) may allow increased
transmission distances. The ISL32450E, ISL32452E, and
ISL32457E can operate at 115kbps or less at the full 4000ft
(1220m) distance, or at 250kbps for lengths up to 3000ft
(915m). DC cable attenuation is the limiting parameter, so using
better quality cables (such as 22 AWG) may allow increased
transmission distance.
Use twisted pair cables for RS-485/RS-422 networks. Twisted
pair cables tend to pick up noise and other electromagnetically
induced voltages as common-mode signals that are effectively
rejected by the differential receivers in these ICs.
Note: Proper termination is imperative to minimize reflections
when using the 20Mbps ISL32458E and ISL32459E devices.
Short networks using the 250kbps ISL32450E, ISL32452E, and
ISL32457E versions do not need to be terminated; however,
terminations are recommended unless power dissipation is an
overriding concern.
connecting receivers to the main cable as short as possible.
Multipoint (multidriver) systems require that the main cable is
terminated in its characteristic impedance at both ends. Keep
stubs connecting a transceiver to the main cable as short as
possible.
Built-In Driver Overload Protection
The RS-485 specification requires that drivers survive worst-case
bus contentions undamaged. These transceivers meet this
requirement through driver output short-circuit current limits and
on-chip thermal shutdown circuitry.
The driver output stages incorporate a double foldback
short-circuit current limiting scheme that ensures that the output
current never exceeds the RS-485 specification, even at the
common-mode and fault condition voltage range extremes. The
first foldback current level (≈83mA) is set to ensure that the
driver never folds back when driving loads with common-mode
voltages up to ±20V. The very low second foldback current
setting (≈13mA) minimizes power dissipation if the Tx is enabled
when a fault occurs.
In the event of a major short-circuit condition, the ISL3245xE’s
thermal shutdown feature disables the drivers whenever the die
temperature becomes excessive. Thermal shutdown eliminates
the power dissipation allowing the die to cool. The drivers
automatically re-enable after the die temperature drops about
15°C. If the contention persists, the thermal shutdown/re-enable
cycle repeats until the fault is cleared. The receivers stay
operational during thermal shutdown.
Low Power Shutdown Mode
These BiCMOS transceivers all use a fraction of the power
required by competitive devices, but they (excluding ISL32457E
and ISL32459E) also include a shutdown feature that reduces
the already low quiescent ICC to a 10µA trickle. These devices
enter shutdown whenever the receiver and driver are
simultaneously disabled (RE = VCC and DE = GND) for a period of
at least 600ns. Disabling both the driver and the receiver for less
than 60ns ensures that the transceiver does not enter shutdown.
Note: The receiver and driver enable times increase when the
transceiver enables from shutdown. See Notes 12 through 16 on
page 11 for more information.
Die Characteristics
SUBSTRATE POTENTIAL (POWERED UP):
GND
PROCESS:
Si Gate BiCMOS
In point-to-point or point-to-multireceiver networks (single driver
on bus like RS-422), terminate the main cable in its
characteristic impedance (typically 120Ω) at the end farthest
from the driver. In multireceiver applications, keep stubs
FN7921 Rev.3.00
Feb 14, 2019
Page 19 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted.
Please visit our website to make sure you have the latest revision.
DATE
REVISION
CHANGE
Feb 14, 2019
FN7921.3
Updated links throughout document.
Updated ordering information table by adding all tape and reel information and updating notes.
Updated last sentence in second paragraph in “High Overvoltage (Fault) Protection Increases Ruggedness” on
page 18
Removed About Intersil section.
Updated disclaimer.
August 31, 2017
FN7921.2
Updated the receiving truth table on page 3.
December 1, 2015
FN7921.1
Added 20Mbps versions (ISL32458E and ISL32459E) to datasheet.
Replaced Products section with About Intersil verbiage.
Updated Package Outline Drawing M10.118 to the latest version. Changes are as follows:
-Updated to new POD template. Added land pattern.
February 20, 2012
FN7921.0
Initial release
FN7921 Rev.3.00
Feb 14, 2019
Page 20 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
Package Outline Drawings
For the most recent package outline drawing, see M8.118.
M8.118
8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 7/11
5
3.0±0.05
A
DETAIL "X"
D
8
1.10 MAX
SIDE VIEW 2
0.09 - 0.20
4.9±0.15
3.0±0.05
5
0.95 REF
PIN# 1 ID
1
2
B
0.65 BSC
GAUGE
PLANE
TOP VIEW
0.55 ± 0.15
0.25
3°±3°
0.85±010
H
DETAIL "X"
C
SEATING PLANE
0.25 - 0.36
0.08 M C A-B D
0.10 ± 0.05
0.10 C
SIDE VIEW 1
(5.80)
NOTES:
(4.40)
(3.00)
1. Dimensions are in millimeters.
(0.65)
(0.40)
(1.40)
TYPICAL RECOMMENDED LAND PATTERN
FN7921 Rev.3.00
Feb 14, 2019
2. Dimensioning and tolerancing conform to JEDEC MO-187-AA
and AMSEY14.5m-1994.
3. Plastic or metal protrusions of 0.15mm max per side are not
included.
4. Plastic interlead protrusions of 0.15mm max per side are not
included.
5. Dimensions are measured at Datum Plane "H".
6. Dimensions in ( ) are for reference only.
Page 21 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
M8.15
For the most recent package outline drawing, see M8.15.
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 1/12
DETAIL "A"
1.27 (0.050)
0.40 (0.016)
INDEX
6.20 (0.244)
5.80 (0.228)
AREA
0.50 (0.20)
x 45°
0.25 (0.01)
4.00 (0.157)
3.80 (0.150)
1
2
8°
0°
3
0.25 (0.010)
0.19 (0.008)
SIDE VIEW “B”
TOP VIEW
2.20 (0.087)
SEATING PLANE
5.00 (0.197)
4.80 (0.189)
1.75 (0.069)
1.35 (0.053)
1
8
2
7
0.60 (0.023)
1.27 (0.050)
3
6
4
5
-C-
1.27 (0.050)
0.51(0.020)
0.33(0.013)
SIDE VIEW “A
0.25(0.010)
0.10(0.004)
5.20(0.205)
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
20. Dimensioning and tolerancing per ANSI Y14.5M-1994.
21. Package length does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
22. Package width does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
23. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
24. Terminal numbers are shown for reference only.
25. The lead width as measured 0.36mm (0.014 inch) or greater above the
seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch).
26. Controlling dimension: MILLIMETER. Converted inch dimensions are not
necessarily exact.
27. This outline conforms to JEDEC publication MS-012-AA ISSUE C.
FN7921 Rev.3.00
Feb 14, 2019
Page 22 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
M10.118
For the most recent package outline drawing, see M10.118.
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
Rev 1, 4/12
5
3.0±0.05
A
DETAIL "X"
D
10
1.10 MAX
SIDE VIEW 2
0.09 - 0.20
4.9±0.15
3.0±0.05
5
0.95 REF
PIN# 1 ID
1
2
0.50 BSC
B
GAUGE
PLANE
TOP VIEW
0.55 ± 0.15
0.25
3°±3°
0.85±010
H
DETAIL "X"
C
SEATING PLANE
0.18 - 0.27
0.08 M C A-B D
0.10 ± 0.05
0.10 C
SIDE VIEW 1
(5.80)
NOTES:
(4.40)
(3.00)
1. Dimensions are in millimeters.
2. Dimensioning and tolerancing conform to JEDEC MO-187-BA
and AMSEY14.5m-1994.
3. Plastic or metal protrusions of 0.15mm max per side are not
included.
4. Plastic interlead protrusions of 0.15mm max per side are not
included.
(0.50)
(0.29)
(1.40)
5. Dimensions are measured at Datum Plane "H".
6. Dimensions in ( ) are for reference only.
TYPICAL RECOMMENDED LAND PATTERN
FN7921 Rev.3.00
Feb 14, 2019
Page 23 of 25
ISL32450E, ISL32452E, ISL32453E, ISL32455E, ISL32457E, ISL32458E, ISL32459E
M14.15
For the most recent package outline drawing, see M14.15.
14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 1, 10/09
8.65
A 3
4
0.10 C A-B 2X
6
14
DETAIL"A"
8
0.22±0.03
D
6.0
3.9
4
0.10 C D 2X
0.20 C 2X
7
PIN NO.1
ID MARK
5
0.31-0.51
B 3
(0.35) x 45°
4° ± 4°
6
0.25 M C A-B D
TOP VIEW
0.10 C
1.75 MAX
H
1.25 MIN
0.25
GAUGE PLANE C
SEATING PLANE
0.10 C
0.10-0.25
1.27
SIDE VIEW
(1.27)
DETAIL "A"
(0.6)
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSEY14.5m-1994.
3. Datums A and B to be determined at Datum H.
(5.40)
4. Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
5. The pin #1 indentifier may be either a mold or mark feature.
(1.50)
6. Does not include dambar protrusion. Allowable dambar protrusion
shall be 0.10mm total in excess of lead width at maximum condition.
7. Reference to JEDEC MS-012-AB.
TYPICAL RECOMMENDED LAND PATTERN
FN7921 Rev.3.00
Feb 14, 2019
Page 24 of 25
1RWLFH
'HVFULSWLRQVRIFLUFXLWVVRIWZDUHDQGRWKHUUHODWHGLQIRUPDWLRQLQWKLVGRFXPHQWDUHSURYLGHGRQO\WRLOOXVWUDWHWKHRSHUDWLRQRIVHPLFRQGXFWRUSURGXFWV
DQGDSSOLFDWLRQH[DPSOHV