DATASHEET
ISL54062
FN6581
Rev 1.00
Nov 3, 2009
Negative Signal Swing, Sub-ohm, Dual SPDT with Click and Pop Elimination
Single Supply Switch
The Intersil ISL54062 device is a low ON-resistance, low
voltage, bidirectional, dual single-pole/double-throw (SPDT)
analog switch. It is designed to operate from a single +1.8V to
+6.5V supply and pass signals that swing down to 6.5V below
the positive supply rail. Targeted applications include battery
powered equipment that benefit from low rON (0.56low
power consumption (20nA) and fast switching speeds
(tON = 55ns, tOFF = 18ns). The digital inputs are 1.8V
logic-compatible up to a +3V supply. The ISL54062 also
features integrated circuitry to eliminate click and pop noise to
an audio speaker. The ISL54062 is offered in a small form
factor package, alleviating board space limitations. It is
available in a tiny 10 Ld 1.8x1.4mm µTQFN or 10 Ld 3x3mm
TDFN package.
The ISL54062 is a committed dual single-pole/double-throw
(SPDT) that consist of two normally open (NO) and two
normally closed (NC) switches with independent logic control.
This configuration can be used as a dual 2-to-1 multiplexer.
Number of Switches
2
SW
SPDT or 2-to-1 MUX
4.3V rON
0.57
4.3V tON/tOFF
43ns/23ns
2.7V rON
0.82
2.7V tON/tOFF
55ns/18ns
• rON Matching Between Channels . . . . . . . . . . . . . . . . .10m
• rON Flatness Across Signal Range . . . . . . . . . . . . . . . .0.35
• Low THD+N @ 32Load . . . . . . . . . . . . . . . . . . . . . . 0.02%
• Single Supply Operation. . . . . . . . . . . . . . . . . +1.8V to +6.5V
• Low Power Consumption @ 3V (PD) . . . . . . . . . . . 24nW
tON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43ns
tOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23ns
• 1.8V Logic Compatible (+3V supply)
• Low I+ Current when VINH is not at the V+ Rail
• Available in 10 Ld µTQFN 1.8x1.4mm and 10 Ld 3x3mm
TDFN
1.8
145ns/28ns
Packages
10 Ld µTQFN, 10 Ld TDFN
Applications
• Audio and Video Switching
ON-RESISTANCE vs SUPPLY VOLTAGE vs
SWITCH VOLTAGE
• Battery powered, Handheld, and Portable Equipment
- MP3 and Multimedia Players
- Cellular/mobile Phones
- Pagers
- Laptops, Notebooks, Palmtops
V+ = 1.8V
1.6
1.4
rON ()
• ON-Resistance (rON)
- V+ = +4.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.55
- V+ = +4.3V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.57
- V+ = +2.7V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.82
- V+ = +1.8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8
• Guaranteed Break-before-Make
1.8V rON
1.2
• Portable Test and Measurement
1.0
• Medical Equipment
V+ = 2.7V
0.8
0.6
Related Literature
V+ = 4.5V
0.4
0.2
-6
• Audio Click and Pop Elimination Circuitry
• ESD HBM Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >6kV
1.8V tON/tOFF
1.8
• Negative Signal Swing (Max 6.5V Below V+)
-
ISL54062
ICOM = 100mA
• Pb-free (RoHS Compliant)
• Fast Switching Action (V+ = +4.3V)
TABLE 1. FEATURES AT A GLANCE
2.0
Features
-5
-4
FN6581 Rev 1.00
Nov 3, 2009
-3
-2
0
-1
VCOM (V)
1
2
3
4
5
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
• Application Note AN557 “Recommended Test Procedures
for Analog Switches”
Page 1 of 16
ISL54062
Pinout
Truth Table
(Note 1)
ISL54062
(10 LD TDFN)
TOP VIEW
IN1 1
10 IN2
9 NO2
NO1 2
8 COM2
COM1 3
GND 5
ISL54062
(10 LD µTQFN)
TOP VIEW
NO1
IN2
7
6
5
8
COM1
9
NC1
10
CLICK
AND POP
CIRCUITRY
1
2
GND
V+
NC1
NO1
NC2
NO2
0
0
ON
OFF
ON
OFF
0
1
ON
OFF
OFF
ON
1
0
OFF
ON
ON
OFF
1
1
OFF
ON
OFF
ON
Logic “0” 0.5V. Logic “1” 1.4V with a 3V supply.
Pin Descriptions
6 V+
IN1
IN2
NOTE:
7 NC2
CLICK
AND POP
CIRCUITRY
NC1 4
IN1
NO2
4
COM2
3
NC2
PIN
FUNCTION
V+
IC Power Supply (+1.8V to +6.5V). Decouple V+ to
ground by placing a 0.1µF capacitor at the V+ and GND
supply lines as near as the IC as possible.
GND
Ground Connection
INx
Digital Control Input
COMx
Analog Switch Common Pin
NOx
Analog Switch Normally Open Pin
NCx
Analog Switch Normally Closed Pin
NOTE:
1. Switches Shown for INx = Logic “0”.
Ordering Information
PART
NUMBER
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL54062IRTZ
(Note 3)
4062
-40 to +85
10 Ld 3x3 TDFN
L10.3x3A
ISL54062IRTZ-T
(Notes 2, 3)
4062
-40 to +85
10 Ld 3x3 TDFN (Tape and Reel)
L10.3x3A
ISL54062IRUZ-T
(Notes 2, 4)
8
-40 to +85
10 Ld Thin µTQFN (Tape and Reel)
L10.1.8x1.4A
NOTES:
2. Please refer to TB347 for details on reel specifications.
3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD020.
4. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu
plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN6581 Rev 1.00
Nov 3, 2009
Page 2 of 16
ISL54062
Absolute Maximum Ratings
Thermal Information
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 7.0V
Input Voltages
NOx, NCx (Note 5) . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
INx (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)
Output Voltages
COMx (Note 5) . . . . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
Continuous Current NOx, NCx, or COMx. . . . . . . . . . . . . ±300mA
Peak Current NOx, NCx, or COMx
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>400V
Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . >1.5kV
Thermal Resistance (Typical)
JA (°C/W)
JC (°C/W)
10 Ld 3x3 TDFN Package (Notes 6, 8)
55
18
10 Ld µTQFN Package (Note 7) . . . . .
155
N/A
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Power Supply Range . . . . . . . . . . . . . . . . . . . . . . . . +1.8V to +6.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
5. Signals on NC, NO, IN, or COM exceeding V+ or GND by specified amount are clamped by internal diodes. Limit forward diode current to
maximum current ratings.
6. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
7. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
8. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 9), Unless
Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 10, 11)
TYP
MAX
(Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
V+ = 4.5V, ICOM = 100mA, VNO or VNC = (V+ - 6.5)
to V+ (see Figure 5)
25
-
0.55
-
Full
-
0.68
-
rON Matching Between Channels,
rON
V+ = 4.5V, ICOM = 100mA, VNO or VNC = Voltage at
max rON, (Note 13)
25
-
15
-
m
Full
-
30
-
m
rON Flatness, RFLAT(ON)
V+ = 4.5V, ICOM = 100mA, VNO or VNC = (V+ - 6.5)
to V+, (Note 12)
25
-
0.11
-
Full
-
0.14
-
COM ON Leakage Current,
ICOM(ON)
V+ = 5V, VCOM = -1.5V, 5V, VNO or VNC = Float
25
-
49
-
nA
Full
-
0.7
-
µA
ns
ON-Resistance, rON
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
Turn-OFF Time, tOFF
V+ = 4.5V, VNO or VNC = 3.0V, RL = 50,
CL = 35pF (see Figure 1)
V+ = 4.5V, VNO or VNC = 3.0V, RL = 50,
CL = 35pF (see Figure 1)
25
-
35
-
Full
-
50
-
ns
25
-
16
-
ns
Full
-
22
-
ns
Break-Before-Make Time Delay, tD V+ = 5.5V, VNO or VNC = 3.0V, RL = 50,
CL = 35pF (see Figure 3)
Full
-
18
-
ns
Charge Injection, Q
VG = 0V, RG = 0, CL = 1.0nF (see Figure 2)
25
-
170
-
pC
OFF-Isolation
RL = 50, CL = 5pF, f = 100kHz, VCOM = 1VRMS
(see Figure 4)
25
-
60
-
dB
Crosstalk (Channel-to-Channel)
RL = 50, CL = 5pF, f = 1MHz, VCOM = 1VRMS
(see Figure 6)
25
-
-75
-
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 0.5VP-P, RL = 32
25
-
0.02
-
%
-3dB Bandwidth
VCOM = 1VRMS, RL = 50CL = 5pF
25
-
60
-
MHz
NO x or NCx OFF Capacitance,
COFF
f = 1MHz
25
-
36
-
pF
FN6581 Rev 1.00
Nov 3, 2009
Page 3 of 16
ISL54062
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 9), Unless
Otherwise Specified. (Continued)
PARAMETER
COMx ON Capacitance,
CCOM(ON)
TEST CONDITIONS
f = 1MHz (see Figure 7)
TEMP
MIN
(°C) (Notes 10, 11)
TYP
MAX
(Notes 10, 11) UNITS
25
-
88
-
pF
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
V+ = 5.5V, VIN = 0V or V+
25
-
0.02
0.1
µA
Full
-
2.5
-
µA
Full
-
-
0.8
V
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
Input Voltage High, VINH
Input Current, IINH, IINL
V+ = 5.5V, VIN = 0V or V+
Full
2.4
-
-
V
25
-0.1
-
0.1
µA
Full
-
0.89
-
µA
Electrical Specifications - 4.3V SupplyTest Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Note 9), Unless
Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 10, 11)
TYP
MAX
(Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, rON
V+ = 4.3V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V)
to V+, (See Figure 5)
rON Matching Between
Channels, rON
V+ = 4.3V, ICOM = 100mA, VNO or VNC = Voltage at
max rON, (Note 12)
rON Flatness, RFLAT(ON)
V+ = 4.3V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V)
to V+, (Note 13)
COM ON Leakage Current,
ICOM(ON)
V+ = 4.3V, VCOM = -1.2V, 4.3V, VNO or VNC = Float
25
-
0.57
-
Full
-
0.68
-
25
-
15
-
m
Full
-
30
-
m
25
-
0.1
-
Full
-
0.14
-
25
-0.1
-
0.1
µA
Full
-
1.1
-
µA
25
-
43
-
ns
Full
-
50
-
ns
25
-
23
-
ns
Full
-
23
-
ns
Full
-
22
-
ns
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
Turn-OFF Time, tOFF
V+ = 3.9V, VNO or VNC = 3.0V, RL = 50, CL = 35pF
(see Figure 1)
V+ = 3.9V, VNO or VNC = 3.0V, RL = 50, CL = 35pF
(see Figure 1)
Break-Before-Make Time Delay, V+ = 4.5V, VNO or VNC = 3.0V, RL = 50, CL = 35pF
tD
(see Figure 3)
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0see Figure 2)
25
-
200
-
pC
OFF-Isolation
RL = 50, CL = 5pF, f = 100kHz, VCOM = 1VRMS
(see Figure 4)
25
-
60
-
dB
Crosstalk (Channel-to-Channel) RL = 50, CL = 5pF, f = 1MHz, VCOM = 1VRMS
(see Figure 6)
25
-
-75
-
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 32
25
-
0.04
-
%
NOx or NCx OFF Capacitance,
COFF
f = 1MHz
25
-
36
-
pF
COMx ON Capacitance,
CCOM(ON)
f = 1MHz (see Figure 7)
25
-
88
-
pF
FN6581 Rev 1.00
Nov 3, 2009
Page 4 of 16
ISL54062
Electrical Specifications - 4.3V SupplyTest Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Note 9), Unless
Otherwise Specified. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 10, 11)
TYP
MAX
(Notes 10, 11) UNITS
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
V+ = +4.5V, VIN = 0V or V+
25
-
0.003
0.1
µA
Full
-
2.6
-
µA
25
-
0.89
12
µA
Input Voltage Low, VINL
Full
-
-
0.5
V
Input Voltage High, VINH
Full
1.6
-
-
V
25
-0.5
-
0.5
µA
Full
-
0.5
-
µA
Positive Supply Current, I+
V+ = +4.2V, VIN = 2.85V
DIGITAL INPUT CHARACTERISTICS
Input Current, IINH, IINL
V+ = 4.5V, VIN = 0V or V+
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 9), Unless
Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 10, 11) TYP (Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, rON
V+ = 2.7V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V)
to V+ (see Figure 5)
rON Matching Between
Channels, rON
V+ = 2.7V, ICOM = 100mA, VNO or VNC = Voltage at
max rON (Note 13)
rON Flatness, RFLAT(ON)
V+ = 2.7V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V)
to V+ (Notes 12, 14)
25
-
0.82
-
Full
-
0.94
-
25
-
10
-
m
Full
-
30
-
m
25
-
0.35
0.5
Full
-
0.4
0.55
25
-
55
-
ns
Full
-
82
-
ns
25
-
18
-
ns
Full
-
24
-
ns
Full
-
30
-
ns
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50, CL = 35pF
(see Figure 1)
Turn-OFF Time, tOFF
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50, CL = 35pF
(see Figure 1)
Break-Before-Make Time Delay,
tD
V+ = 3.3V, VNO or VNC = 1.5V, RL = 50, CL = 35pF
(see Figure 3)
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0see Figure 2)
25
-
150
-
pC
OFF-Isolation
RL = 50, CL = 5pF, f = 100kHz, VCOM = 1VRMS
(see Figure 4)
25
-
60
-
dB
Crosstalk (Channel-to-Channel)
RL = 50, CL = 5pF, f = 1MHz, VCOM = 1VRMS
(see Figure 6)
25
-
-75
-
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 0.5VP-P, RL = 32
25
-
0.04
-
%
NOx or NCx OFF Capacitance,
COFF
f = 1MHz
25
-
36
-
pF
COMx ON Capacitance,
CCOM(ON)
f = 1MHz (see Figure 7)
25
-
88
-
pF
25
-
-
0.5
V
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
Input Voltage High, VINH
Input Current, IINH, IINL
FN6581 Rev 1.00
Nov 3, 2009
V+ = 3.3V, VIN = 0V or V+
25
1.4
-
-
V
25
-0.5
-
0.5
µA
Full
-
0.4
-
µA
Page 5 of 16
ISL54062
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, VINH = 1.0V, VINL = 0.4V (Note 9), Unless Otherwise
Specified.
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 10, 11)
TYP
MAX
(Notes 10, 11)
UNITS
25
-
1.87
-
Full
-
1.97
-
25
-
16
-
m
Full
-
30
-
m
25
-
1.34
-
Full
-
1.43
-
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, rON
V+ = 1.8V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V)
to V+, (see Figure 5)
rON Matching Between
Channels, rON
V+ = 1.8V, ICOM = 100mA, VNO or VNC = Voltage at
max rON (Note 13)
rON Flatness, RFLAT(ON)
V+ = 1.8V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V)
to V+ (Note 12)
DYNAMIC CHARACTERISTICS
25
-
145
-
ns
Full
-
150
-
ns
25
-
20
-
ns
Full
-
22
-
ns
Break-Before-Make Time Delay, V+ = 1.8V, VNO or VNC = 1.8V, RL = 50, CL = 35pF
(see Figure 3)
tD
Full
-
130
-
ns
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0see Figure 2)
25
-
40
-
pC
Turn-ON Time, tON
Turn-OFF Time, tOFF
V+ = 1.8V, VNO or VNC = 1.8V, RL = 50, CL = 35pF
(see Figure 1)
V+ = 1.8V, VNO or VNC = 1.8V, RL = 50, CL = 35pF
(see Figure 1)
-3dB Bandwidth
VCOM = 1VRMS, RL = 50CL = 5pF
25
-
60
-
MHz
NOx or NCx OFF Capacitance,
COFF
f = 1MHz
25
-
36
-
pF
COMx ON Capacitance,
CCOM(ON)
f = 1MHz (see Figure 7)
25
-
88
-
pF
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
25
-
-
0.4
V
Input Voltage High, VINH
25
1.0
-
-
V
Input Current, IINH, IINL
V+ = 2.0V, VIN = 0V or V+
25
-0.5
-
0.5
µA
Input Current, IINH, IINL
V+ = 2.0V, VIN = 0V or V+
Full
-
0.38
-
µA
NOTES:
9. VIN = input voltage to perform proper function.
10. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
11. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
12. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
13. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON
value, between NC1 and NC2 or between NO1 and NO2.
14. Limits established by characterization and are not production tested.
FN6581 Rev 1.00
Nov 3, 2009
Page 6 of 16
ISL54062
Test Circuits and Waveforms
V+
LOGIC
INPUT
V+
tr < 5ns
tf < 5ns
50%
0V
tOFF
SWITCH
INPUT VNO
SWITCH
INPUT
VOUT
NO OR NC
COM
IN
VOUT
90%
SWITCH
OUTPUT
C
90%
LOGIC
INPUT
CL
35pF
RL
50
GND
0V
tON
Logic input waveform is inverted for switches that have the opposite
logic sense.
Repeat test for all switches. CL includes fixture and stray
capacitance.
RL
V OUT = V (NO or NC) -----------------------R L + r ON
FIGURE 1A. MEASUREMENT POINTS
FIGURE 1B. TEST CIRCUIT
FIGURE 1. SWITCHING TIMES
V+
RG
SWITCH
OUTPUT
VOUT
C
VOUT
COM
NO OR NC
VOUT
VG
IN
GND
CL
V+
LOGIC
INPUT
ON
ON
OFF
LOGIC
INPUT
0V
Q = VOUT x CL
Repeat test for all switches.
FIGURE 2A. MEASUREMENT POINTS
FIGURE 2B. TEST CIRCUIT
FIGURE 2. CHARGE INJECTION
V+
V+
LOGIC
INPUT
VNX
NO
RL
50
IN
90%
0V
VOUT
COM
NC
0V
SWITCH
OUTPUT
VOUT
C
LOGIC
INPUT
CL
35pF
GND
tBBM
FIGURE 3A. MEASUREMENT POINTS
Repeat test for all switches. CL includes fixture and stray
capacitance.
FIGURE 3B. TEST CIRCUIT
FIGURE 3. BREAK-BEFORE-MAKE TIME
FN6581 Rev 1.00
Nov 3, 2009
Page 7 of 16
ISL54062
Test Circuits and Waveforms (Continued)
V+
C
V+
C
*50 SOURCE
SIGNAL
GENERATOR
rON = V1/100mA
NO OR NC
NO OR NC
IN
VNX
0V OR V+
100mA
0V OR V+
IN
V1
COM
ANALYZER
GND
COM
RL
GND
Signal direction through switch is reversed, worst case values
are recorded. Repeat test for all switches.
Repeat test for all switches.
FIGURE 4. OFF-ISOLATION TEST CIRCUIT
FIGURE 5. rON TEST CIRCUIT
V+
V+
C
*50 SOURCE
SIGNAL
GENERATOR
NO1 OR NC1
COM1
C
COM
50
IN
INX
0V OR V+
COM2
ANALYZER
RL
0V OR V+
IMPEDANCE
ANALYZER
NC2 OR NO2
NC
NO OR NC
GND
GND
Signal direction through switch is reversed, worst case values
are recorded. Repeat test for all switches.
FIGURE 6. CROSSTALK TEST CIRCUIT
FN6581 Rev 1.00
Nov 3, 2009
FIGURE 7. ON CAPACITANCE TEST CIRCUIT
Page 8 of 16
ISL54062
Test Circuits and Waveforms (Continued)
INx
VDC
0V
220uF
VINx*
NCx
0V
tD
VDC
tD
COMx
CLICK AND POP
CIRCUITRY
*VINx waveform for Click and Pop Elimination on NOx terminal.
RL
220uF
For Click and Pop Elimination on NCx terminal invert VINx.
NOx
VDC
tD = 200ms measured at 50% points.
FIGURE 8A. CLICK AND POP WAVEFORM
FIGURE 8B. CLICK AND POP TEST CIRCUIT
FIGURE 8. CLICK AND POP ELIMINATION
Detailed Description
The ISL54062 is a bi-directional, dual single pole-double throw
(SPDT) analog switch that offers precise switching from a
single 1.8V to 6.5V supply with low ON-resistance (0.83),
high speed operation (tON = 55ns, tOFF = 18ns) and negative
signal swing capability. The device is especially well suited for
portable battery powered equipment due to its low operating
supply voltage (1.8V), low power consumption (20nA @ 3V),
and a tiny 1.8mmx1.4mm µTQFN package or a 3x3 TDFN
package. The low ON-resistance and rON flatness provide very
low insertion loss and signal distortion for applications that
require signal switching with minimal interference by the switch.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the purpose
of using a low rON switch. Alternatively, connecting external
Schottky diodes from the V+ rail to the signal pins will shunt the
fault current through the Schottky diode instead of through the
internal ESD diodes, thereby protecting the switch. These
Schottky diodes must be sized to handle the expected fault
current.
V+
+RING
VCOMx
VNCx
VNOx
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. The ISL54062
contains ESD protection diodes on each pin of the IC
(see Figure 9). These diodes connect to either a +Ring or
-Ring for ESD protection. To prevent forward biasing the ESD
diodes to the +Ring, V+ must be applied before any input
signals, and the input signal voltages must remain between
recommended operating range.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at the
logic pin and signal pins from exceeding the maximum ratings
of the switch. The following two methods can be used to
provided additional protection to limit the current in the event
that the voltage at a logic pin or switch terminal goes above the
V+ rail.
Logic inputs can be protected by adding a 1k resistor in
series with the logic input (see Figure 9). The resistor limits the
input current below the threshold that produces permanent
damage.
FN6581 Rev 1.00
Nov 3, 2009
CLAMP
1k
LOGIC
INPUTS
GND
-RING
FIGURE 9. OVERVOLTAGE PROTECTION
Power-Supply Considerations
The ISL54062 construction is typical of most single supply
CMOS analog switches which have two supply pins: V+ and
GND. V+ and GND provide the CMOS switch bias and sets
their analog voltage limits. Unlike switches with a 5.5V
maximum supply voltage, the ISL54062’s 6.5V maximum
supply voltage provides plenty of head room for the 10%
tolerance of 5V supplies due to overshoot and noise spikes.
The minimum recommended supply voltage is 1.8V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer to
Page 9 of 16
ISL54062
the “Electrical Specifications” tables, beginning on page 3, and
“Typical Performance Curves”, beginning on page 11, for
details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to V+ and GND
signals levels to drive the analog switch gate terminals. A high
frequency decoupling capacitor placed as close to the V+ and
GND pin as possible is recommended for proper operation of
the switch. A value of 0.1µF is highly recommended.
be taken for driving a smaller load impedance under this
scenario.
V+
C
AUDIO
SOURCE A
220µF
NO
RSH
COM
RL
32
Negative Signal Swing Capability
The ISL54062 contains circuitry that allows the analog switch
signal to swing below ground. The device has an analog signal
range of 6.5V below V+ up to the V+ rail (see Figure 16) while
maintaining low rON performance. For example, if V+ = 5V,
then the analog input signal range is from -1.5V to +5V. If V+ =
2.7V then the range is from -3.8V to +2.7V.
220µF
NC
AUDIO
SOURCE B
RSH
IN
GND
ISL54062
Click and Pop Operation
The ISL54062 contains circuitry that prevents audible click and
pop noises that may occur when audio sources are powered
on or off. Single supply audio sources are biased at a DC offset
that can generate transients during power on/off. A DC
blocking capacitor is needed to remove the DC bias at the
speaker load. For 32 headphones, a 220µF capacitor is
typically used to preserve the audio bandwidth. The power
on/off transients are AC coupled by the 220µF capacitor to the
speaker load causing a click and pop noise.
The ISL54062 has shunt switches on the NO and NC pins to
eliminate click and pop transients (see Figure 10). These
switches are driven complimentary to the main switch. When
NC is connected to COM, the shunt switch is active on the NO
pin (and vice versa). The shunt switches connect an
impedance (140typical, see Figure 24) from the NO/NC pin
to ground to discharge any transients that may appear on the
NO or NC pins.
When a DC bias becomes active at the source, the NO and NC
terminals will also have a DC offset due to capacitor dv/dt
principle. The DC offset will be discharged through the shunt
impedance on the NO and NC terminals instead of the
speaker, eliminating click and pop noise.
*Under high impedance loads such as the input impedance of
pre-amplifiers (20k, the COM terminal voltage may rise due
to small leakage currents charging the COM capacitance. This
is not seen when low impedance loads such as headphones
(32) are used because the small leakage currents does not
result in significant potential drop across the load. If the user
desires to reduce the voltage build up on the COM pin, a 1k
resistor to ground may be placed on the COM pin. This
impedance is small enough to reduce the voltage build up
significantly while not increasing the power dissipation
dramatically. Current consumption considerations will need to
FIGURE 10. CLICK AND POP OPERATION
Click and Pop Elimination with INx Pin
Audio click and pop elimination can be driven with the Input
Select (INx) pin. When INx = 0, the NOx terminals are
connected to the shunt impedance. When INx = 1, the NCx
terminals are connected to the shunt impedance. In this
situation, only one of the source transient voltages will be
shunted to ground, depending on the Input Select state. The
Input Select pin should be driven 200ms after any source
transients occurs to prevent audible transients at the speaker
load.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.45V VOLMAX
and 1.35V VOHMIN) over a supply range of 1.8V to 3.3V (see
Figure 18). At 3.3V the VIL level is 0.5V maximum. This is still
below the 1.8V CMOS guaranteed low output maximum level
of 0.45V, but noise margin is reduced to approximately 50mV.
At 3.3V the VIH level is 1.4V minimum. While this is above the
1.8V CMOS guaranteed high output minimum of 1.35V, under
most operating conditions the switch will recognize this as a
valid logic high.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving the
digital input signals from GND to V+ with a fast transition time
minimizes power dissipation. The ISL54062 has been
designed to minimize the supply current whenever the digital
input voltage is not driven to the supply rails (0V to V+). For
example, driving the device with 2.85V logic high while
operating with a 4.2V supply the device draws only 1µA of
current.
High-Frequency Performance
In 50 systems, the ISL54062 has an ON switch -3dB
bandwidth of 60MHz (see Figure 21). The frequency response
FN6581 Rev 1.00
Nov 3, 2009
Page 10 of 16
ISL54062
is very consistent over a wide V+ range, and for varying analog
signal levels.
An OFF switch acts like a capacitor across the open terminals
and AC couples higher frequencies, resulting in signal feedthrough from a switch’s input to its output. Off-Isolation is the
resistance to this feed-through. Crosstalk indicates the amount
of feed-through from one switch channel to another switch
channel. Figure 22 details the high Off-Isolation and Crosstalk
rejection provided by this part. At 100kHz, Off-Isolation is about
60dB in 50 systems, decreasing approximately 20dB per
decade as frequency increases. At 1MHz, Crosstalk is about 75dB in 50 systems, decreasing approximately 20dB per
decade as frequency increases.
Leakage Considerations
Reverse ESD protection diodes are internally connected between
each analog-signal pin, V+ and GND. One of these diodes
conducts if any analog signal exceeds the recommended analog
signal range.
Virtually all the analog switch leakage current comes from the
ESD diodes and reversed biased junctions in the switch cell.
Although the ESD diodes on a given signal pin are identical and
therefore fairly well balanced, they are reverse biased differently.
Each is biased to either the +Ring or -Ring and the analog input
signal. This means their leakages will vary as the signal varies.
The difference in the two diode leakages to the +Ring or -Ring
and the reverse biased junctions at the internal switch cell
constitutes the analog-signal-path leakage current.
Typical Performance Curves TA = +25°C, Unless Otherwise Specified
1.00
2.0
1.8
ICOM = 100mA
0.90
0.85
1.6
0.80
1.4
0.75
1.2
rON ()
rON ()
V+ = 4.5V
ICOM = 100mA
0.95
V+ = 1.8V
1.0
0.65
0.60
T = +25°C
0.55
V+ = 2.7V
0.8
T = +85°C
0.70
0.50
0.6
0.40
0.4
0.2
-6
T = -40°C
0.45
V+ = 4.5V
0.35
-5
-4
-3
-2
0
-1
1
2
3
4
5
0.30
-3
-2
0
-1
VCOM (V)
FIGURE 11. ON-RESISTANCE vs SUPPLY VOLTAGE vs
SWITCH VOLTAGE
2
3
4
5
FIGURE 12. ON-RESISTANCE vs SWITCH VOLTAGE
1.25
1.00
0.95
V+ = 4.3V
ICOM = 100mA
0.90
V+ = 2.7V
ICOM = 100mA
1.15
0.85
1.05
0.80
0.95
0.70
rON ()
0.75
rON ()
1
VCOM (V)
T = +85°C
0.65
0.60
T = +25°C
0.55
0.85
0.75
0.65
T = +85°C
0.55
T = +25°C
0.50
T = -40°C
0.45
0.40
0.45
0.35
0.30
-3
-2
-1
0
1
2
3
4
VCOM (V)
FIGURE 13. ON-RESISTANCE vs SWITCH VOLTAGE
FN6581 Rev 1.00
Nov 3, 2009
5
0.35
-5
T = -40°C
-4
-3
-2
0
-1
VCOM (V)
1
2
3
FIGURE 14. ON-RESISTANCE vs SWITCH VOLTAGE
Page 11 of 16
4
ISL54062
Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued)
6
2.2
V+ = 1.8V
2.0
5
ICOM = 100mA
ANALOG SIGNAL RANGE (V)
1.6
rON ()
1.4
1.2
1.0
0.8
T = +85°C
0.6
T = +25°C
0.4
0.2
-5
3
2
1
0
-1
-2
-3
-5
-4
-3
-2
-1
VCOM (V)
0
1
2
-6
3
700
ABSOLUTE VALUES
500
VINH AND VINL (V)
V+ = 4.5V
Q (pC)
450
400
350
V+ = 3.3V
300
250
200
150
50
0
-5
2.5
1.3
1.2
550
100
2.0
V+ = 2.0V
-4
-3
-2
-1
0
1
VCOM (V)
2
3
4
5
FIGURE 17. CHARGE INJECTION vs SWITCH VOLTAGE
3.0
3.5
4.0
4.5
SUPPLY VOLTAGE (V)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
6
2.0
2.5
3.0
V+ (V)
3.5
4.0
T = -40°C
35
T = +25°C
T = +85°C
120
T = +25°C
T = +85°C
30
25
tOFF (ns)
100
80
20
60
15
40
10
20
5
0
1.8
3.3
V+ (V)
4.5
5.5
FIGURE 19. TURN-ON TIME vs SUPPLY VOLTAGE
FN6581 Rev 1.00
Nov 3, 2009
4.5
FIGURE 18. DIGITAL SWITCHING POINT vs SUPPLY VOLTAGE
40
140
6.0
VINL
T = -40°C
tON (ns)
5.5
VINH
1.1
1.0
0.1
0
1.5
160
0
5.0
1.6
1.5
1.4
V+ = 5.5V
650
1.5
FIGURE 16. ANALOG SIGNAL RANGE vs SUPPLY VOLTAGE
FIGURE 15. ON-RESISTANCE vs SWITCH VOLTAGE
600
SIGNAL MIN
-4
T = -40°C
6
SIGNAL MAX
4
1.8
1.8
3.3
4.5
5.5
V+ (V)
FIGURE 20. TURN-OFF TIME vs SUPPLY VOLTAGE
Page 12 of 16
ISL54062
Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued)
0
V+ = 1.8V TO 5.5V
V+ = 1.8V TO 5.5V
-20
RL = 50
VIN = 1VRMS @ 0VDC OFFSET
-30
-2
CROSSTALK (dB)
NORMALIZED GAIN (dB)
-1
-10
-3
-4
-5
-40
-50
OFF-ISOLATION
-60
CROSSTALK
-70
-80
-90
RL = 50
VIN = 1VRMS @ 0VDC OFFSET
1k
10k
100k
1M
10M
FREQUENCY (Hz)
-100
100M
1G
-110
1k
10k
100k
1M
FREQUENCY (Hz)
10M
100M
FIGURE 22. CROSSTALK AND OFF-ISOLATION
FIGURE 21. FREQUENCY RESPONSE
0.05
350
V+ = 1.8V
325
707mVRMS
0.04
300
275
THD+N (%)
360mVRMS
250
0.03
225
200
177mVRMS
0.02
V+ = 3V
175
V+ = 4.3V
150
0.01
125
V+ = 3.3V
100
VBIAS = 0VDC
RL =32
0
20
V+ = 5V
75
100
200
1k
2k
FREQUENCY (Hz)
10k
20k
FIGURE 23. TOTAL HARMONIC DISTORTION vs FREQUENCY
FN6581 Rev 1.00
Nov 3, 2009
50
-5
-4
-3
-2
-1
0
1
2
3
4
5
SWITCH VOLTAGE (V)
FIGURE 24. SHUNT RESISTANCE vs SWITCH VOLTAGE
Page 13 of 16
6
ISL54062
Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued)
V+ = 3V
VDC = 1.5VDC
INx (1V/DIV)
RL = 20k
V+ = 3V
INx (1V/DIV)
VDC = 1.5VDC
RL = 32
VDC (1V/DIV)
VDC (1V/DIV)
VNO (500mV/DIV)
VNO (500mV/DIV)
*VCOM (10mV/DIV)
VCOM (10mV/DIV)
*See CLICK AND POP OPERATION
TIME ( 200ms/DIV)
FIGURE 25. CLICK AND POP ELIMINATION 20k LOAD
200ms DELAY
TIME ( 200ms/DIV)
FIGURE 26. CLICK AND POP ELIMINATION 32 LOAD 200ms
DELAY
Die Characteristics
SUBSTRATE POTENTIAL (POWERED UP):
GND (DFN Paddle Connection: Tie to GND or Float)
TRANSISTOR COUNT:
432
PROCESS:
Submicron CMOS
© Copyright Intersil Americas LLC 2009. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6581 Rev 1.00
Nov 3, 2009
Page 14 of 16
ISL54062
Thin Dual Flat No-Lead Plastic Package (TDFN)
L10.3x3A
2X
0.10 C A
A
10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
D
MILLIMETERS
2X
0.10 C B
E
B
//
A
C
SEATING
PLANE
D2
(DATUM B)
6
INDEX
AREA
0.10 C
0.08 C
A3
SIDE VIEW
7
8
NOMINAL
MAX
NOTES
A
0.70
0.75
0.80
-
A1
-
-
0.05
-
0.20 REF
b
0.20
-
0.25
0.30
1
5, 8
D
2.95
3.0
3.05
-
D2
2.25
2.30
2.35
7, 8
E
2.95
3.0
3.05
-
E2
1.45
1.50
1.55
7, 8
e
0.50 BSC
-
k
0.25
-
-
-
L
0.25
0.30
0.35
8
N
10
2
Nd
5
3
Rev. 3 3/06
D2/2
NOTES:
2
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
NX k
3. Nd refers to the number of terminals on D.
(DATUM A)
4. All dimensions are in millimeters. Angles are in degrees.
E2
E2/2
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
NX L
N
8
MIN
A3
6
INDEX
AREA
TOP VIEW
SYMBOL
N-1
NX b
e
(Nd-1)Xe
REF.
BOTTOM VIEW
5
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
0.10 M C A B
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
9. Compliant to JEDEC MO-229-WEED-3 except for D2
dimensions.
CL
NX (b)
(A1)
L1
5
9 L
e
SECTION "C-C"
C C
TERMINAL TIP
FOR ODD TERMINAL/SIDE
FN6581 Rev 1.00
Nov 3, 2009
Page 15 of 16
ISL54062
Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN)
D
6
INDEX AREA
2X
A
L10.1.8x1.4A
B
N
10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC
PACKAGE
MILLIMETERS
E
SYMBOL
0.10 C
1
2X
2
0.10 C
TOP VIEW
C
A
0.05 C
SIDE VIEW
(DATUM A)
PIN #1 ID
1
2
NX L
NX b 5
10X
0.10 M C A B
0.05 M C
L1
5
(DATUM B)
7
MAX
NOTES
0.50
0.55
-
A1
-
-
0.05
-
0.127 REF
-
b
0.15
0.20
0.25
5
D
1.75
1.80
1.85
-
E
1.35
1.40
1.45
-
e
A1
NOMINAL
0.45
A3
0.10 C
SEATING PLANE
MIN
A
0.40 BSC
-
L
0.35
0.40
0.45
L1
0.45
0.50
0.55
-
N
10
2
Nd
2
3
Ne
3
3
0
-
12
4
Rev. 3 6/06
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
e
3. Nd and Ne refer to the number of terminals on D and E side,
respectively.
BOTTOM VIEW
4. All dimensions are in millimeters. Angles are in degrees.
NX (b)
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
CL
(A1)
5
L
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Maximum package warpage is 0.05mm.
SECTION "C-C"
e
8. Maximum allowable burrs is 0.076mm in all directions.
TERMINAL TIP
C C
2.20
1.00
0.60
1.00
9. JEDEC Reference MO-255.
10. For additional information, to assist with the PCB Land Pattern
Design effort, see Intersil Technical Brief TB389.
0.50
1.80
0.40
0.20
0.20
0.40
10 LAND PATTERN
FN6581 Rev 1.00
Nov 3, 2009
Page 16 of 16