DATASHEET
ISL55004
FN6219
Rev 2.00
July 27, 2006
High Supply Voltage 200MHz Unity-Gain Stable Operational Amplifier
The ISL55004 is a high speed, low power, low cost
monolithic operational amplifier. The ISL55004 is unity-gain
stable and features a 300V/µs slew rate and 200MHz
bandwidth while requiring only 8.5mA of supply current per
amplifier.
The power supply operating range of the ISL55004 is from
±15V down to ±2.5V. For single-supply operation, the
ISL55004 operates from 30V down to 5V.
The ISL55004 also features an extremely wide output
voltage swing of -12.75V/+13.4V with VS = ±15V and
RL = 1k.
At a gain of +1, the ISL55004 has a -3dB bandwidth of
200MHz with a phase margin of 55°. Because of its
conventional voltage-feedback topology, the ISL55004 allow
the use of reactive or non-linear elements in its feedback
network. This versatility combined with low cost and 140mA
of output-current drive makes the ISL55004 an ideal choice
for price-sensitive applications requiring low power and high
speed.
The ISL55004 is in a 14 Ld SO (0.150”) package and
specified for operation over the full -40°C to +85°C
temperature range.
Ordering Information
TAPE
&
PART
PART NUMBER MARKING REEL
Features
• 200MHz -3dB bandwidth
• Unity-gain stable
• Low supply current: 8.5mA per amplifier
• Wide supply range: ±2.5V to ±15V dual-supply and 5V to
30V single-supply
• High slew rate: 300V/µs
• Fast settling: 75ns to 0.1% for a 10V step
• Wide output voltage swing: -12.75V/+13.4V with
VS = ±15V, RL = 1k
• Enhanced replacement for EL2444
• Pb-free plus anneal available (RoHS compliant)
Applications
• Video amplifiers
• Single-supply amplifiers
• Active filters/integrators
• High speed sample-and-hold
• High speed signal processing
• ADC/DAC buffers
PACKAGE
PKG.
DWG. #
ISL55004IB
55004IB
-
14 Ld SO (0.150”) MDP0027
ISL55004IB-T7
55004IB
7”
14 Ld SO (0.150”) MDP0027
ISL55004IB-T13
55004IB
13”
14 Ld SO (0.150”) MDP0027
ISL55004IBZ
(See Note)
55004IBZ
-
14 Ld SO (0.150”) MDP0027
(Pb-Free)
ISL55004IBZ-T7 55004IBZ
(See Note)
7”
14 Ld SO (0.150”) MDP0027
(Pb-Free)
ISL55004IBZ-T13 55004IBZ
(See Note)
13”
14 Ld SO (0.150”) MDP0027
(Pb-Free)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
• Pulse/RF amplifiers
• Pin diode receivers
• Log amplifiers
• Photo multiplier amplifiers
• Difference amplifiers
Pinout
ISL55004
[14 LD SO (0.150”)]
TOP VIEW
OUT1 1
IN1- 2
- +
+ -
13 IN4-
IN1+ 3
12 IN4+
VS+ 4
11 VS-
IN2+ 5
10 IN3+
IN2- 6
OUT2 7
FN6219 Rev 2.00
July 27, 2006
14 OUT4
- +
+ -
9 IN38 OUT3
Page 1 of 12
ISL55004
Absolute Maximum Ratings (TA = 25°C)
Power Dissipation (PD) . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Operating Temperature Range (TA). . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature (TST) . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Supply Voltage (VS) . . . . . . . . . . . . . . . . . . . . . . . . . . ±16.5V or 33V
Input Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±VS
Differential Input Voltage (dVIN). . . . . . . . . . . . . . . . . . . . . . . . .±10V
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER
VS = ±15V, AV = +1, RL = 1k, TA = 25°C, unless otherwise specified.
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
1.2
5
mV
VOS
Input Offset Voltage
TCVOS
Average Offset Voltage Drift (Note 1)
IB
Input Bias Current
VS = ±15V
0.6
3.5
µA
IOS
Input Offset Current
VS = ±15V
0.2
2
µA
TCIOS
Average Offset Current Drift (Note 1)
AVOL
Open-loop Gain
VS = ±15V, VOUT = ±10V, RL = 1k
PSRR
Power Supply Rejection Ratio
CMRR
VS = ±15V
17
µV/°C
0.2
nA/°C
12000
21000
V/V
VS = ±5V to ±15V
75
100
dB
Common-mode Rejection Ratio
VCM = ±10V, VOUT = 0V
75
90
dB
CMIR
Common-mode Input Range
VS = ±15V
13
V
VOUT
Output Voltage Swing
VO+, RL = 1k
13.25
13.4
V
VO-, RL = 1k
-12.6
-12.75
V
VO+, RL = 150
9.6
10.7
V
VO-, RL = 150
-8.3
-9.4
V
80
140
mA
ISC
Output Short Circuit Current
IS
Supply Current (per amplifier)
RIN
Input Resistance
CIN
Input Capacitance
ROUT
PSOR
VS = ±15V, no load
8.5
2.0
9.25
mA
3.2
M
AV = +1
1
pF
Output Resistance
AV = +1
50
m
Power Supply Operating Range
Dual supply
Single supply
±2.25
±15
V
4.5
30
V
MAX
UNIT
NOTE:
1. Measured from TMIN to TMAX.
AC Electrical Specifications
PARAMETER
BW
VS = ±15V, AV = +1, RL = 1k, TA = 25°C, unless otherwise specified.
DESCRIPTION
-3dB Bandwidth (VOUT = 0.4VPP)
CONDITION
MIN
TYP
VS = ±15V, AV = +1
200
MHz
VS = ±15V, AV = -1
55
MHz
VS = ±15V, AV = +2
53
MHz
VS = ±15V, AV = +5
17
MHz
GBWP
Gain Bandwidth Product
VS = ±15V
70
MHz
PM
Phase Margin
RL = 1k, CL = 5pF
55
°
SR
Slew Rate (Note 1)
300
V/µs
FN6219 Rev 2.00
July 27, 2006
260
Page 2 of 12
ISL55004
AC Electrical Specifications
PARAMETER
VS = ±15V, AV = +1, RL = 1k, TA = 25°C, unless otherwise specified. (Continued)
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
FPBW
Full-power Bandwidth (Note 2)
VS = ±15V
9.5
MHz
tS
Settling to +0.1% (AV = +1)
VS = ±15V, 10V step
75
ns
dG
Differential Gain (Note 3)
NTSC/PAL
0.01
%
dP
Differential Phase
NTSC/PAL
0.05
°
eN
Input Noise Voltage
10kHz
12
nV/Hz
iN
Input Noise Current
10kHz
1.5
pA/Hz
NOTES:
1. Slew rate is measured on rising edge.
2. For VS = ±15V, VOUT = 10VPP, for VS = ±5V, VOUT = 5VPP. Full-power bandwidth is based on slew rate measurement using FPBW = SR/(2 *
VPEAK).
3. Video performance measured at VS = ±15V, AV = +2 with two times normal video level across RL = 150. This corresponds to standard video
levels across a back-terminated 75 load. For other values or RL, see curves.
Typical Performance Curves
FIGURE 1. OPEN-LOOP GAIN vs FREQUENCY
FIGURE 2. OPEN-LOOP PHASE vs FREQUENCY
4
2
3
1
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
4
VS = 15V
RF = 500
RL = 500
AV = +1
0
AV = +2
-1
-2
AV = +5
-3
-4
-5
-6
100k
2
VS = 15V
RF = 500
RL = 500
1
0
AV = -1
-1
AV = -2
-2
-3
AV = -5
-4
-5
1M
10M
100M
FREQUENCY (Hz)
FIGURE 3. GAIN vs FREQUENCY FOR VARIOUS NONINVERTING GAIN SETTINGS
FN6219 Rev 2.00
July 27, 2006
1G
-6
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 4. GAIN vs FREQUENCY FOR VARIOUS INVERTING
GAIN SETTINGS
Page 3 of 12
ISL55004
Typical Performance Curves
(Continued)
FIGURE 5. PHASE vs FREQUENCY FOR VARIOUS NONINVERTING GAIN SETTINGS
GAIN BANDWIDTH PRODUCT (MHz)
100
FIGURE 6. PHASE vs FREQUENCY FOR VARIOUS
INVERTING GAIN SETTINGS
350
RL=500
AV=+2
RF=500
300 RL=500
CL=5pF
SLEW RATE (V/µs)
80
60
40
250
NEGATIVE SLEW RATE
200
20
0
POSITIVE SLEW RATE
150
0
3
6
9
12
100
15
0
3
6
SUPPLY VOLTAGES (±V)
FIGURE 7. GAIN BANDWIDTH PRODUCT vs SUPPLY
1
3
2
RL = 1k
0
RL = 150
-1
-2
RL = 500
-3
RL = 50
-4
VS = 15V
RF = 500
CL = 5pF
AV = +2
RL = 500
1
0
-1
RL = 1k
RL = 150
-2
RL = 50
-3
-4
-5
-5
-6
100k
15
4
VS = 15V
RF = 0
CL = 5pF
AV = +1
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
2
12
FIGURE 8. SLEW RATE vs SUPPLY
4
3
9
SUPPLY VOLTAGES (±V)
1M
10M
100M
FREQUENCY (Hz)
FIGURE 9. GAIN vs FREQUENCY FOR VARIOUS RLOAD
(AV = +1)
FN6219 Rev 2.00
July 27, 2006
1G
-6
100k
1M
10M
100M
FREQUENCY (Hz)
FIGURE 10. GAIN vs FREQUENCY FOR VARIOUS RLOAD
(AV = +2)
Page 4 of 12
1G
ISL55004
Typical Performance Curves
(Continued)
4
4
VS = 15V
RF = 0
RL = 500
AV = +1
NORMALIZED GAIN (dB)
2
CL = 27pF
1
CL = 15pF
0
CL = 5pF
-1
-2
-3
CL = 0pF
-4
VS = 15V
RF = 500
RL = 500
AV = +2
3
CL = 47pF
NORMALIZED GAIN (dB)
3
2
CL = 100pF
1
CL = 39pF
0
CL = 22pF
-1
CL = 5pF
-2
-3
-4
-5
-5
-6
100k
1M
10M
100M
-6
100k
1G
1M
FIGURE 11. GAIN vs FREQUENCY FOR VARIOUS CLOAD
(AV = +1)
0
RF = 100
RF = 250
RF = 0
-2
VS = 15V
RL = 500
CL = 5pF
AV = +2
3
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
RF = 500
-1
-3
-4
-5
2
RF = 500
1
0
RF = 1k
RF = 250
-1
-2
RF = 100
-3
-4
-5
-6
100k
1M
10M
100M
-6
100k
1G
1M
FREQUENCY (Hz)
1G
4
VS = 15V
RF = 500
RL = 500
CL = 5pF
AV = +2
CIN = 10pF
3
CIN = 6.8pF
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
100M
FIGURE 14. GAIN vs FREQUENCY FOR VARIOUS RFEEDBACK
(AV = +2)
4
1
10M
FREQUENCY (Hz)
FIGURE 13. GAIN vs FREQUENCY FOR VARIOUS RFEEDBACK
(AV = +1)
2
1G
4
VS = 15V
RL = 500
CL = 5pF
AV = +1
1
3
100M
FIGURE 12. GAIN vs FREQUENCY FOR VARIOUS CLOAD
(AV = +2)
4
2
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
3
CL = 68pF
CIN = 4.7pF
0
-1
CIN = 2.2pF
-2
CIN = 0pF
-3
-4
-5
-6
100k
2
1
RF = 0
RL = 500
CL = 5pF
AV = +1
VS = 2.5V
0
VS = 10V
-1
VS = 15V
-2
-3
VS = 5V
-4
-5
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 15. GAIN vs FREQUENCY FOR VARIOUS INVERTING
INPUT CAPACITANCE (CIN)
FN6219 Rev 2.00
July 27, 2006
-6
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 16. GAIN vs FREQUENCY FOR VARIOUS SUPPLY
SETTINGS
Page 5 of 12
ISL55004
Typical Performance Curves
(Continued)
FIGURE 17. COMMON-MODE REJECTION RATIO (CMRR)
FIGURE 18. POWER SUPPLY REJECTION RATIO (PSRR)
HARMONIC DISTORTION (dBc)
-20
VS=±15V
-30 AV=+1
RF=0
-40 RL=500
CL=5pF
-50 VOUT=2VP-P
THD
-60
2ND HD
-70
3RD HD
-80
-90
-100
500K
1M
10M
40M
FREQUENCY (Hz)
FIGURE 19. HARMONIC DISTORTION vs FREQUENCY
(AV = +1)
FIGURE 20. HARMONIC DISTORTION vs OUTPUT VOLTAGE
(AV = +2)
OUTPUT VOLTAGE SWING (Vp-p)
25
RL=500
CL=5pF
AV=+1
20
AV=+2
RF=500
15
10
5
0
0
3
6
9
12
15
SUPPLY VOLTAGES (±V)
FIGURE 21. OUTPUT SWING vs FREQUENCY FOR VARIOUS
GAIN SETTINGS
FN6219 Rev 2.00
July 27, 2006
FIGURE 22. OUTPUT SWING vs SUPPLY VOLTAGE FOR
VARIOUS GAIN SETTINGS
Page 6 of 12
ISL55004
Typical Performance Curves
(Continued)
20% to 80% 80% to 20%
20% to 80%
80% to 20%
FIGURE 23. LARGE SIGNAL RISE AND FALL TIMES
FIGURE 24. SMALL SIGNAL RISE AND FALL TIMES
1.2
POWER DISSIPATION (W)
TOTAL SUPPLY CURRENT [mA]
25
20
15
10
AV=+1
RF=0
RL=500
CL=5pF
5
0
0
3
6
9
12
FIGURE 25. SUPPLY CURRENT vs SUPPLY VOLTAGE
0.6
0.4
0.2
0
25
50
75 85 100
125
150
FIGURE 26. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.6
POWER DISSIPATION (W)
0.8
AMBIENT TEMPERATURE (°C)
SUPPLY VOLTAGES (±V)
1.8
SO14
JA=120°C/W
1 1.042W
0
15
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.420W
1.4
SO14
JA=88°C/W
1.2
1
0.8
0.6
0.4
0.2
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 27. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FN6219 Rev 2.00
July 27, 2006
Page 7 of 12
ISL55004
Product Description
The ISL55004 is a wide bandwidth, low power, and low offset
voltage feedback operational amplifier. This device is internally
compensated for closed loop gain of +1 or greater. Connected
in voltage follower mode and driving a 500 load, the -3dB
bandwidth is around a 200MHz. Driving a 150 load and a
gain of 2, the bandwidth is about 90MHz while maintaining a
300V/µs slew rate.
The ISL55004 is designed to operate with supply voltage from
+15V to -15V. That means for single supply application, the
supply voltage is from 0V to 30V. For split supplies application,
the supply voltage is from ±15V. The amplifier has an input
common-mode voltage range from 1.5V above the negative
supply (VS- pin) to 1.5V below the positive supply (VS+ pin). If
the input signal is outside the above specified range, it will
cause the output signal to be distorted.
The outputs of the ISL55004 can swing from -12.75V to +13.4V
for VS = ±15V. As the load resistance becomes lower, the
output swing is lower.
Choice of Feedback Resistor and Gain Bandwidth
Product
For applications that require a gain of +1, no feedback resistor
is required. Just short the output pin to the inverting input pin.
For gains greater than +1, the feedback resistor forms a pole
with the parasitic capacitance at the inverting input. As this
pole becomes smaller, the amplifier's phase margin is reduced.
This causes ringing in the time domain and peaking in the
frequency domain. Therefore, RF can't be very big for optimum
performance. If a large value of RF must be used, a small
capacitor in the few Pico Farad range in parallel with RF can
help to reduce the ringing and peaking at the expense of
reducing the bandwidth. For gain of +1, RF = 0 is optimum. For
the gains other than +1, optimum response is obtained with RF
with proper selection of RF and RG (see Figures15 and 16 for
selection).
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same frequency
response as DC levels are changed at the output. This is
especially difficult when driving a standard video load of 150,
because of the change in output current with DC level. The dG
and dP of this device is about 0.01% and 0.05°, while driving
150 at a gain of 2. Driving high impedance loads would give a
similar or better dG and dP performance.
Driving Capacitive Loads and Cables
The ISL55004 can drive 47pF loads in parallel with 500 with
less than 3dB of peaking at gain of +1 and as much as 100pF
at a gain of +2 with under 3db of peaking. If less peaking is
desired in applications, a small series resistor (usually between
5 to 50) can be placed in series with the output to eliminate
most peaking. However, this will reduce the gain slightly. If the
gain setting is greater than 1, the gain resistor RG can then be
FN6219 Rev 2.00
July 27, 2006
chosen to make up for any gain loss which may be created by
the additional series resistor at the output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier's output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help to
reduce peaking.
Output Drive Capability
The ISL55004 does not have internal short circuit protection
circuitry. It has a typical short circuit current of 140mA. If the
output is shorted indefinitely, the power dissipation could easily
overheat the die or the current could eventually compromise
metal integrity. Maximum reliability is maintained if the output
current never exceeds ±60mA. This limit is set by the design of
the internal metal interconnect. Note that in transient
applications, the part is robust.
Short circuit protection can be provided externally with a back
match resistor in series with the output placed close as
possible to the output pin. In video applications this would be a
75 resistor and will provide adequate short circuit protection
to the device. Care should still be taken not to stress the device
with a short at the output.
Power Dissipation
With the high output drive capability of the ISL55004, it is
possible to exceed the 150°C absolute maximum junction
temperature under certain load current conditions. Therefore, it
is important to calculate the maximum junction temperature for
an application to determine if load conditions or package types
need to be modified to assure operation of the amplifier in a
safe operating area.
The maximum power dissipation allowed in a package is
determined according to:
T JMAX – T AMAX
PD MAX = -------------------------------------------- JA
Where:
• TJMAX = Maximum junction temperature
• TAMAX = Maximum ambient temperature
• JA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC is
the total quiescent supply current times the total power supply
voltage, plus the power in the IC due to the load, or:
For sourcing:
n
PD MAX = V S I SMAX +
V OUTi
VS – VOUTi ---------------R Li
i=1
Page 8 of 12
ISL55004
For sinking:
n
PD MAX = V S I SMAX +
VOUTi – VS ILOADi
i=1
Where:
• VS = Supply voltage
• ISMAX = Maximum quiescent supply current
• VOUT = Maximum output voltage of the application
• RLOAD = Load resistance tied to ground
• ILOAD = Load current
Power Supply Bypassing Printed Circuit Board
Layout
As with any high frequency device, a good printed circuit board
layout is necessary for optimum performance. Lead lengths
should be as short as possible. The power supply pin must be
well bypassed to reduce the risk of oscillation. For normal
single supply operation, where the VS- pin is connected to the
ground plane, a single 4.7µF tantalum capacitor in parallel with
a 0.1µF ceramic capacitor from VS+ to GND will suffice. This
same capacitor combination should be placed at each supply
pin to ground if split supplies are to be used. In this case, the
VS- pin becomes the negative supply rail.
Printed Circuit Board Layout
• N = number of amplifiers (max = 4)
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
Caution: For supply voltages greater then 20V, the maximum
power dissipation at 85°C ambient temperature could be
exceeded. For higher supply voltages the maximum ambient
temperature must be de-rated according to the Package Power
Dissipation curve Figure 27. The maximum power dissipation
is highly dependent upon the thermal conductivity of the PCB.
For lower thermal conductivity boards use Figure 26.
For good AC performance, parasitic capacitance should be
kept to minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use of
sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is very important. The
feedback resistor should be placed very close to the inverting
input pin. Strip line design techniques are recommended for
the signal traces.
Application Circuits
Sallen Key Low Pass Filter
A common and easy to implement filter taking advantage of the
wide bandwidth, low offset and low power demands of the
ISL55004. A derivation of the transfer function is provided for
convenience (See Figure 28).
Sallen Key High Pass Filter
Again this useful filter benefits from the characteristics of the
ISL55004. The transfer function is very similar to the low pass
so only the results are presented (See Figure 29).
© Copyright Intersil Americas LLC 2005-2006. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6219 Rev 2.00
July 27, 2006
Page 9 of 12
ISL55004
K 1
V2
5V
1
V1
R2C2s 1
Vo
V1 Vi
Vo Vi
K
1 V1
0
1
R1
R2
C1s
K
H(s)
R1C1R2C2s 2 ((1 K )R1C1 R1C2 R21C2)s 1
1
H( jw )
1 w 2R1C1R2C2 jw ((1 K )R1C1 R1C2 R2C2)
Vo K
C5
1nF
C1
1nF
R1
R2
1k
V1
1k C2
1nF
+
V+
-
V-
VOUT
R7
1k
RB
Holp K
1k
RA
1k
RB
RA
C5
wo
1nF
Q
V3
5V
1
R1C1R2C2
1
R1C1
R1C2
R2C2
(1 K )
R2C2
R2C1
R1C1
Holp K
V2
5V
Holp K
C5
Q
1nF
R1
V1
1k
R2
1k C2
1nF
+
V+
-
V-
R1C1R2C2
1
R1C1
R1C2
R2C2
(1 K )
R2C2
R2C1
R1C1
VOUT
R7
1k
RB
RA
1k
1
wo
1nF
C1
Equations simplify if we let all
components be equal R=C
1
wo
RC
1
Q
3 K
FIGURE 28. SALLEN KEY LOW PASS FILTER
Holp
1k
C5
wo
1nF
V3
5V
Q
K
4 K
2
RC
Equations simplify if we let
all components be equal R=C
2
4 K
FIGURE 29. SALLEN KEY HIGH PASS FILTER
FN6219 Rev 2.00
July 27, 2006
Page 10 of 12
ISL55004
Differential Output Instrumentation Amplifier
e o3 = – 1 + 2R 2 R G e 1 – e 2
The addition of a third amplifier to the conventional three
amplifier instrumentation amplifier introduces the benefits of
differential signal realization, specifically the advantage of
using common-mode rejection to remove coupled noise and
ground potential errors inherent in remote transmission. This
configuration also provides enhanced bandwidth, wider output
swing and faster slew rate than conventional three amplifier
solutions with only the cost of an additional amplifier and few
resistors.
e1
A1
R3
+
-
A3
+
RG
R3
R3
R3
R3
A4
R2
+
-
A2
e2
R3
+
e o = – 2 1 + 2R 2 R G e 1 – e 2
2f C1 2
BW = -----------------A Di
A Di = – 2 1 + 2R 2 R G
Strain Gauge
The strain gauge is an ideal application to take advantage of
the moderate bandwidth and high accuracy of the ISL55004.
The operation of the circuit is very straightforward. As the
strain variable component resistor in the balanced bridge is
subjected to increasing strain, its resistance changes, resulting
in an imbalance in the bridge. A voltage variation from the
referenced high accuracy source is generated and translated
to the difference amplifier through the buffer stage. This
voltage difference as a function of the strain is converted into
an output voltage.
R3
R2
e o4 = 1 + 2R 2 R G e 1 – e 2
eo3
+
REF
eo
eo4
R3
FIGURE 30. DIFFERENTIAL OUTPUT AMPLIFIER
+V
2
5V
C6
VARIABLE SUBJECT
TO STRAIN
V5 +
0V
-
R15
1k
1k
R16
1k
1nF
R17
1k
R18
1k
1k
+
V+
-
V-
VOUT
RL
(V1+V2+V3+V4)
1k
RF
1k
C12
1nF
+
V4
- 5V
FIGURE 31. STRAIN GAUGE
FN6219 Rev 2.00
July 27, 2006
Page 11 of 12
ISL55004
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
SYMBOL
SO-8
SO-14
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
N
8
14
16
NOTES:
Rev. L 2/01
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
FN6219 Rev 2.00
July 27, 2006
Page 12 of 12