DATASHEET
ISL65426
FN6340
Rev 3.00
March 25, 2008
6A Dual Synchronous Buck Regulator with Integrated MOSFETs
The ISL65426 is a high efficiency dual output monolithic
synchronous buck converter operating over an input
voltage range of 3V to 5.5V. This single chip power solution
provides two output voltages, which are selectable or
externally adjustable from 1V to 80% of the supply voltage
while delivering up to 6A of total output current. The two
PWMs are synchronized 180° out-of-phase, reducing the
RMS input current and ripple voltage.
The ISL65426 switches at a fixed frequency of 1MHz and
utilizes current-mode control with integrated compensation
to minimize the size and number of external components
and provide excellent transient response. The internal
synchronous power switches are optimized for good
thermal performance and high efficiency.
A unique power block architecture allows partitioning of six
1A blocks to support one of four configuration options. One
master power block is associated with each synchronous
converter channel. Four floating slave power blocks allow
the user to assign them to either channel. Proper external
configuration of the power blocks is verified internally prior
to soft-start initialization.
Independent enable inputs allow for synchronization or
sequencing soft-start intervals of the two converter
channels. A third enable input allows additional sequencing
for multi-input bias supply designs. Individual power-good
indicators (PG1, PG2) signal when output voltage is within
the regulation window.
The ISL65426 integrates protection for both synchronous
buck regulator channels. The fault conditions include
overcurrent, undervoltage, and IC thermal monitor.
High integration contained in a thin Quad Flat No-lead
(QFN) package makes the ISL65426 an ideal choice to
power many of today’s small form factor applications. A
single chip solution for large scale digital ICs, like field
programmable gate arrays (FPGA), requiring separate core
and I/O voltages.
Features
• High Efficiency: Up to 95%
• Fixed Frequency: 1MHz
• Operates From 3V to 5.5V Supply
• ±1% Reference
• Flexible Output Voltage Options
- Programmable 2-Bit VID Input
- Adjustable Output From 1V to 4.0V
• User-Partitioned Power Blocks
• Ultra-Compact DC/DC Converter Design
• PWMs Synchronized 180° Out-of-Phase
• Independent Enable Inputs and System Enable
• Stable All Ceramic Solutions
• Excellent Dynamic Response
• Independent Output Digital Soft-Start
• Power-Good Output Voltage Monitor
• Thermal-Overload Protection
• Overcurrent and Undervoltage Protection
• Pb-Free (RoHS Compliant)
Applications
• FPGA, CPLD, DSP, and CPU Core and I/O Voltages
- Xilinx Spartan IIITM, Virtex IITM, Virtex II ProTM,
Virtex 4TM
- Altera StratixTM, Stratix IITM, CycloneTM, Cyclone IITM
- Actel FusionTM, LatticeSCTM, LatticeECTM
• Low-Voltage, High-Density Distributed Power Systems
• Point-of-Load Regulation
• Distributed Power Systems
• Set-Top Boxes
Ordering Information
PART
NUMBER
(Note)
PART
MARKING
TEMP.
RANGE
(°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
ISL65426HRZ* ISL65426 HRZ -10 to +100 50 Ld 5x10 QFN L50.5x10
ISL65426IRZA* ISL65426 IRZ
-40 to +85 50 Ld 5x10 QFN L50.5x10
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on
reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach materials
and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which
is RoHS compliant and compatible with both SnPb and Pb-free
soldering operations. Intersil Pb-free products are MSL classified at Pbfree peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
FN6340 Rev 3.00
March 25, 2008
Page 1 of 22
ISL65426
Pinout
PG2
FB2
PG1
EN
ISET2
EN2
EN1
FB1
ISL65426
(50 LD QFN)
TOP VIEW
50 49 48 47 46 45 44 43
PGND 1
42 PGND
PGND 2
41 PGND
PGND 3
40 PGND
PGND
39 PGND
4
LX1 5
38 LX6
LX1 6
37 LX6
PVIN1 7
36 PVIN6
PVIN2 8
35 PVIN5
LX2 9
34 LX5
PGND
PGND 10
33 PGND
PGND 11
32 PGND
LX3 12
31 LX4
PVIN3 13
30 PVIN4
VCC 14
29 PGND
VCC 15
28 PGND
VCC 16
27 GND
PGND 17
26 GND
PGND
PGND
V2SET2
V2SET1
ISET1
V1SET2
PGND
FN6340 Rev 3.00
March 25, 2008
V1SET1
18 19 20 21 22 23 24 25
Page 2 of 22
ISL65426
Typical Application Schematics
SINGLE INPUT SUPPLY
EN
EN2
EN1
3.3V
PG2
PG1
3.3V
PVIN1
PVIN6
PVIN2
PVIN5
3.3V
3.3V
C1
C4
PVIN4
PVIN3
LX1
LX6
LX2
LX5
L2
L1
1.2V
3A
ISL65426
C2
C3
LX3
LX4
FB1
FB2
VCC
2.5V
3A
3.3V
C5
GND
V2SET1
V1SET2
V2SET2
ISET2
ISET1
V1SET1
PGND
3.3V
FIGURE 1. TYPICAL APPLICATION FOR 3A:3A CONFIGURATION
FN6340 Rev 3.00
March 25, 2008
Page 3 of 22
ISL65426
Typical Application Schematics (Continued)
DUAL INPUT SUPPLY
EN
EN2
EN1
5.0V
PG2
PG1
3.3V
PVIN1
PVIN6
PVIN2
5.0V
3.3V
PVIN3
C1
PVIN5
C4
PVIN4
LX6
L2
LX5
1.8V
2A
ISL65426
C3
LX1
L1
1.5V
4A
LX2
FB2
LX3
C2
VCC
LX4
5.0V
C5
FB1
GND
V2SET2
V1SET1
ISET2
V2SET1
V1SET2
ISET1
PGND
3.3V
FIGURE 2. TYPICAL APPLICATION FOR 4A:2A CONFIGURATION
FN6340 Rev 3.00
March 25, 2008
Page 4 of 22
ISL65426
Typical Application Schematics (Continued)
EN
EN2
EN1
5.0V
PG2
PG1
5.0V
PVIN1
PVIN5
PVIN2
5.0V
C2
PVIN3
C1
5.0V
C4
PVIN4
PVIN6
L2
LX5
ISL65426
LX1
C3
3.3V
1A
LX2
L1
LX3
FB2
LX4
C2
2.5V
5A
VCC
LX6
5.0V
C5
FB1
GND
V1SET2
V1SET1
ISET1
V2SET2
V2SET1
ISET2
PGND
5.0V
FIGURE 3. TYPICAL APPLICATION FOR 5A:1A CONFIGURATION
FN6340 Rev 3.00
March 25, 2008
Page 5 of 22
ISL65426
Functional Block Diagram
EN2
EN
VCC GND
POWER-ON
RESET (POR)
EN1
PVINx
PVINx
CURRENT
SENSE
SOFT-START
EA
FB1
V1SET1
V1SET2
SLOPE
COMPENSATION
OUTPUT
VOLTAGE
CONFIG
GM
PWM
CONTROL
LOGIC
GATE
DRIVE
LXx
COMPENSATION
EPAD GND
UV
POWER-GOOD
PGOOD1
THERMAL
MONITOR
PWM
REFERENCE
0.60V
SOFT
START
POWER
DEVICE
CONFIG
ISET1
ISET2
PVINx
POR
SOFT-START
V2SET1
V2SET2
SLOPE
COMPENSATION
EA
FB2
OUTPUT
VOLTAGE
CONFIG
CURRENT
SENSE
GM
PWM
CONTROL
LOGIC
GATE
DRIVE
LXx
COMPENSATION
EPAD GND
OV UV
POWER-GOOD
PGOOD2
FN6340 Rev 3.00
March 25, 2008
Page 6 of 22
ISL65426
Absolute Maximum Ratings
Thermal Information
VCC, PVINx, LXx . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +6V
FBx, ENx, VxSETx, ISETx, PGOODx . . . . . . . -0.3V to VCC + 0.3V
Thermal Resistance
Recommended Operating Input Range
VCC, PVINx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to +5.5V
JA (°C/W)
JC (°C/W)
50 Ld QFN Package (Notes 1, 2). . . . .
23
2.5
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Ambient Temperature Range (ISL65426HRZ). . . . .-10°C to +100°C
Ambient Temperature Range (ISL65426IRZA) . . . . .-40°C to +85°C
Operating Junction Temperature Range . . . . . . . . .-10°C to +125°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379 for details.
2. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. See Tech Brief TB379 for details.
Electrical Specifications
Recommended operating conditions, unless otherwise noted. VCC = PVIN = 5.0V,
TA = -10°C to +100°C for ISL65426HRZ and TA = -40°C to +85°C for ISL65426IRZA. (Note 5)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
POWER SUPPLY
Quiescent Supply Current
EN1 = EN2 = EN = VCC = 5V, IOUT1 = IOUT2 = 0mA
30
Shutdown Supply Current
EN1 = EN2 = EN = GND, VCC = PVIN = 5.5V
5.4
7
mA
EN1 = EN2 = EN = GND, VCC = PVIN = 3.3V
2.8
3.2
mA
mA
PHASE CONFIGURATION
LX Pull-Down
LX1, LX3, LX4, LX5, LX6 Only - Configuration Only
LX Output Leakage
Low Level, Single LX Output
-5
5
µA
High Level, Single LX Output
-5
5
µA
Minimum Controllable ON-time
1
(Note 3)
mA
125
ns
OUTPUT VOLTAGE TOLERANCE
Reference Voltage Tolerance
Programmed Output Voltage Tolerance
TJ = -40°C to +100°C
0.594
0.6
0.606
V
TJ = 100°C to +125°C
0.591
0.6
0.609
V
+2
%
TJ = -40°C to +125°C; No Load
-2
TJ = -40°C to +125°C (Note 4); Full Load
±5
%
OSCILLATOR
Accuracy
0.8
1
1.2
MHz
Maximum LX Pulse Width
950
ns
Minimum LX Pulse Width
50
ns
OUTPUT VOLTAGE SELECTION
VxSETx Input High Threshold
VxSETx Pull-down
0.4
1.2
1.5
V
7
10
15
µA
0.4
1.2
1.5
V
7
10
15
µA
POWER BLOCKS
ISETx Input High Threshold
ISETx Pull-up
Output Current
Per Block; VCC = PVIN = 5.0V; VOUT = 1.8V (Note 3)
Per Block; VCC = PVIN = 3V; VOUT = 1.2V (Note 3)
Peak Output Current Limit
FN6340 Rev 3.00
March 25, 2008
Per Block
2.0
1
A
0.7
A
A
Page 7 of 22
ISL65426
Electrical Specifications
Recommended operating conditions, unless otherwise noted. VCC = PVIN = 5.0V,
TA = -10°C to +100°C for ISL65426HRZ and TA = -40°C to +85°C for ISL65426IRZA. (Note 5) (Continued)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Upper Device rDS(ON)
0.4A Per Block, VCC = PVIN = 3.3V, VOUT = 1.8V
60
100
140
m
Lower Device rDS(ON)
0.4A Per Block, VCC = PVIN = 3.3V, VOUT = 1.8V
30
55
85
m
Efficiency
0.5A Per Block, VCC = PVIN = 3.3V, VOUT = 1.1V
90
%
0.5A Per Block, VCC = PVIN = 5V, VOUT = 2.5V
95
%
POWER-ON RESET AND ENABLE PINS
VCC POR Threshold
PVIN POR Threshold
PVIN Bias Output Voltage Enable Threshold
EN1/EN2 Threshold
VCC Rising; No Load
2.15
2.25
2.35
V
VCC Falling; No Load
2.05
2.15
2.25
V
PVIN Rising; No Load
1.9
2.05
2.15
V
PVIN Falling; No Load
1.75
1.90
2.00
V
VOUT2 = 3.3V; VCC = PVIN
4.1
4.3
4.5
V
VOUT2 = 2.5V; VCC = PVIN
2.8
2.9
3.0
V
Rising Threshold; VCC = 5V
1.0
1.2
1.45
V
0.75
0.98
Hysteresis
Rising Threshold; VCC = 3.3V
280
Hysteresis
Rising Threshold; VCC = 3V
200
0.55
Hysteresis
EN1/EN2 Pull-up
EN Threshold
EN Sink Current
EN = GND
mV
1.20
0.82
V
mV
1.05
185
V
mV
7
10
15
µA
0.57
0.6
0.63
V
7
11
15
µA
Soft-Start Time
4
ms
POWER-GOOD SIGNAL
Rising Threshold
As % of VREF; VOUT1 = 1.8V; VOUT2 = 3.3V
110
115
120
%
Rising Hysteresis
As % of VREF; VOUT1 = 1.8V; VOUT2 = 3.3V
5
7
9
%
Falling Threshold
As % of VREF; VOUT1 = 1.8V; VOUT2 = 3.3V
80
85
90
%
Falling Hysteresis
As % of VREF; VOUT1 = 1.8V; VOUT2 = 3.3V
4
7
9
%
Power-Good Drive
VCC = 5V; PG1 = PG2 = 0.4V
1
mA
Power-Good Leakage
1
µA
PROTECTION FEATURES
Undervoltage Monitor
Undervoltage Trip Threshold
As % of VREF
70
75
80
%
Undervoltage Recovery Threshold
As % of VREF
82
89
95
%
THERMAL MONITOR
Thermal Shutdown Temperature (Note 3)
150
°C
NOTES:
3. Limits should be considered typical and are not production tested.
4. Accounts for output variations due to jitter, which is a function of the input voltage and output loading.
5. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested.
FN6340 Rev 3.00
March 25, 2008
Page 8 of 22
ISL65426
Typical Performance Curves
Circuit of Figure 2. VIN = 5V, IOUT1 = 4A, IOUT2 = 2A, TA = -10°C to +100°C unless otherwise
noted. Typical values are at TA = +25°C.
100
100
90
90
80
70
2.5VIN
3.3VIN
60
70
EFFICIENCY (%)
EFFICIENCY (%)
80
5.5VIN
50
40
30
30
20
10
1.0
2.0
3.0
0
4.0
0.1
1.0
2.0
OUTPUT LOAD (A)
100
90
90
80
2.5VIN
EFFICIENCY (%)
EFFICIENCY (%)
80
5.5VIN
60
3.3VIN
40
30
70
50
30
10
10
0
1.0
2.0
3.0
4.0
5.5VIN
40
20
0.1
2.5VIN
60
20
0
3.3VIN
0.1
0.5
FIGURE 6. VOUT1 = 1.8V EFFICIENCY vs LOAD
100
90
90
2.0
80
4VIN
70
EFFICIENCY (%)
EFFICIENCY (%)
80
60
5.5VIN
50
3VIN
60
30
10
1.5
OUTPUT LOAD (A)
FIGURE 8. VOUT2 = 2.5V EFFICIENCY VS LOAD
FN6340 Rev 3.00
March 25, 2008
2.0
5VIN
40
20
1.0
5.5VIN
50
10
0.5
4.5VIN
70
20
0
0.1
1.5
FIGURE 7. VOUT2 = 1.8V EFFICIENCY vs LOAD
100
30
1.0
OUTPUT LOAD (A)
OUTPUT LOAD (A)
40
4.0
FIGURE 5. VOUT1 = 1.5V EFFICIENCY vs LOAD
100
50
3.0
OUTPUT LOAD (A)
FIGURE 4. VOUT1 = 1.2V EFFICIENCY vs LOAD
70
2.5VIN
40
10
0.1
5.5VIN
50
20
0
3.3VIN
60
0
0.1
0.5
1.0
1.5
OUTPUT LOAD (A)
FIGURE 9. VOUT2 = 3.3V EFFICIENCY vs LOAD
Page 9 of 22
2.0
ISL65426
Circuit of Figure 2. VIN = 5V, IOUT1 = 4A, IOUT2 = 2A, TA = -10°C to +100°C unless otherwise
noted. Typical values are at TA = +25°C. (Continued)
1.235
1.235
1.225
1.225
1.215
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Typical Performance Curves
5.5VIN
1.205
1.195
1.185
2.5VIN
3.3VIN
1.175
NO LOAD
1.205
1.195
1.185
4A LOAD
1.175
1.165
0.1
1.0
2.0
OUTPUT LOAD (A)
3.0
1.165
4.0
2.0
1.545
1.535
1.535
OUTPUT VOLTAGE (V)
1.525
5.5VIN
1.505
1.495
1.485
2.5VIN
1.475
3.3VIN
1.465
1.455
0.1
1.0
2.0
3.0
4.0
4.5
5.0
5.5
1.525
1.515
2A LOAD
NO LOAD
1.505
1.495
1.485
1.475
4A LOAD
1.465
3.0
1.455
2.0
4.0
2.5
3.0
OUTPUT LOAD (A)
3.5
4.0
4.5
5.0
5.5
INPUT VOLTAGE (V)
FIGURE 12. VOUT1 = 1.5V REGULATION vs LOAD
FIGURE 13. VOUT1 = 1.5V REGULATION vs VIN
1.845
1.845
1.825
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
3.5
FIGURE 11. VOUT1 = 1.2V REGULATION vs VIN
1.545
1.515
2.5
INPUT VOLTAGE (V)
FIGURE 10. VOUT1 = 1.2V REGULATION vs LOAD
OUTPUT VOLTAGE (V)
2A LOAD
1.215
5.5VIN
1.805
1.785
2.5VIN
1.765
3.3VIN
1.745
0.1
1.0
2.0
OUTPUT LOAD (A)
3.0
FIGURE 14. VOUT1 = 1.8V REGULATION vs LOAD
FN6340 Rev 3.00
March 25, 2008
4.0
1.825
1.805
2A LOAD
NO LOAD
1.785
1.765
1.745
2.0
4A LOAD
2.5
3.0
3.5
4.0
4.5
5.0
INPUT VOLTAGE (V)
FIGURE 15. VOUT1 = 1.8V REGULATION vs VIN
Page 10 of 22
5.5
ISL65426
Circuit of Figure 2. VIN = 5V, IOUT1 = 4A, IOUT2 = 2A, TA = -10°C to +100°C unless otherwise
noted. Typical values are at TA = +25°C. (Continued)
1.845
1.845
1.825
1.825
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Typical Performance Curves
2.5VIN
1.805
1.785
5.5VIN
1.765
3.3VIN
0.5
1.0
OUTPUT LOAD (A)
1.5
2A LOAD
1.765
2.0
2.0
FIGURE 16. VOUT2 = 1.8V REGULATION vs LOAD
2.565
2.565
2.545
2.545
2.525
4VIN
3.3VIN
2.505
2.485
2.465
5.5VIN
2.445
0.5
1.0
OUTPUT LOAD (A)
1A LOAD
2.465
2.0
1.5
2A LOAD
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
INPUT VOLTAGE (V)
FIGURE 19. VOUT2 = 2.5V REGULATION vs VIN
3.38
3.36
3.36
OUTPUT VOLTAGE (V)
3.40
3.34
5.5VIN
4.5VIN
3.30
3.28
3.26
5VIN
3.34
3.32
NO LOAD
3.30
3.28
3.26
3.24
2A LOAD
1A LOAD
3.22
3.22
3.20
0.5
1.0
1.5
OUTPUT LOAD (A)
FIGURE 20. VOUT2 = 3.3V REGULATION vs LOAD
FN6340 Rev 3.00
March 25, 2008
5.5
2.485
3.38
3.20
0.1
5.0
NO LOAD
2.505
3.40
3.24
3.5
4.0
4.5
INPUT VOLTAGE (V)
2.445
FIGURE 18. VOUT2 = 2.5V REGULATION vs LOAD
3.32
3.0
2.525
2.425
2.425
0.1
2.5
FIGURE 17. VOUT2 = 1.8V REGULATION vs VIN
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.785
1.745
1.745
0.1
OUTPUT VOLTAGE (V)
1A LOAD
NO LOAD
1.805
2.0
4.0
4.25
4.5
4.75
5.0
5.25
INPUT VOLTAGE (V)
FIGURE 21. VOUT2 = 3.3V REGULATION vs VIN
Page 11 of 22
5.5
ISL65426
Typical Performance Curves
Circuit of Figure 2. VIN = 5V, IOUT1 = 4A, IOUT2 = 2A, TA = -10°C to +100°C unless otherwise
noted. Typical values are at TA = +25°C. (Continued)
EN1 5V/DIV
EN1 5V/DIV
VOUT1 500mV/DIV
VOUT1 500mV/DIV
IL1 1A/DIV
IL1 1A/DIV
PG1 5V/DIV
PG1 5V/DIV
FIGURE 22. START-UP VOUT1 = 1.2V (NO LOAD)
FIGURE 23. START-UP VOUT1 = 1.2V (UNDER PRE-BIASED)
EN1 5V/DIV
EN1 5V/DIV
VOUT1 500mV/DIV
VOUT1 500mV/DIV
IL1 2A/DIV
IL1 1A/DIV
PG1 5V/DIV
POK1 5V/DIV
FIGURE 24. START-UP VOUT1 = 1.2V (FULL LOAD)
FIGURE 25. SHUTDOWN VOUT1 = 1.2V
EN2 5V/DIV
EN2 5V/DIV
VOUT2 1V/DIV
VOUT2 1V/DIV
IL2 1A/DIV
IL2 1A/DIV
PG2 5V/DIV
FIGURE 26. START-UP VOUT2 = 3.3V (NO LOAD)
FN6340 Rev 3.00
March 25, 2008
PG2 5V/DIV
FIGURE 27. START-UP VOUT2 = 3.3V (UNDER PRE-BIASED)
Page 12 of 22
ISL65426
Typical Performance Curves
Circuit of Figure 2. VIN = 5V, IOUT1 = 4A, IOUT2 = 2A, TA = -10°C to +100°C unless otherwise
noted. Typical values are at TA = +25°C. (Continued)
EN2 5V/DIV
VOUT1 RIPPLE 20mV/DIV
VOUT2 1V/DIV
IOUT1 1A/DIV
IL2 1A/DIV
VOUT2 RIPPLE 20mV/DIV
PG2 5V/DIV
FIGURE 28. START-UP VOUT2 = 3.3V (FULL-LOAD)
FIGURE 29. VOUT1 = 1.2V LOAD TRANSIENT
VOUT1 RIPPLE 20mV/DIV
LX1 5V/DIV
IOUT1 500mA/DIV
VOUT1 500mV/DIV
VOUT2 RIPPLE 50mV/DIV
IL1 5A/DIV
PG1 5V/DIV
FIGURE 30. VOUT1 = 1.2V LOAD TRANSIENT
FIGURE 31. VOUT1 = 1.2V OUTPUT OVERCURRENT
LX1 5V/DIV
LX2 5V/DIV
VOUT1 500mV/DIV
VOUT2 1V/DIV
IL2 5A/DIV
IL1 5A/DIV
PG1 5V/DIV
FIGURE 32. VOUT1 = 1.2V OUTPUT OVERCURRENT
RECOVERY
FN6340 Rev 3.00
March 25, 2008
PG2 5V/DIV
FIGURE 33. VOUT2 = 3.3V OUTPUT OVERCURRENT
Page 13 of 22
ISL65426
Typical Performance Curves
Circuit of Figure 2. VIN = 5V, IOUT1 = 4A, IOUT2 = 2A, TA = -10°C to +100°C unless otherwise
noted. Typical values are at TA = +25°C. (Continued)
LX2 5V/DIV
VOUT2 1V/DIV
IL2 5A/DIV
PG2 5V/DIV
PG2
Pin Descriptions
FB2
ISET2
PG1
EN
EN2
EN1
FB1
FIGURE 34. VOUT2 = 3.3V OUTPUT OVERCURRENT RECOVERY
VCC
50 49 48 47 46 45 44 43
PGND
1
42 PGND
PGND
2
41 PGND
PGND
3
40 PGND
PGND
4
39 PGND
LX1
5
38 LX6
LX1
6
37 LX6
PVIN1
7
PVIN2
8
LX2
9
36 PVIN6
PGND
35 PVIN5
34 LX5
PGND 10
33 PGND
PGND 11
32 PGND
LX3 12
31 LX4
PVIN3 13
30 PVIN4
VCC 14
29 PGND
VCC 15
28 PGND
VCC 16
27 GND
PGND 17
26 GND
PGND
PGND
V2SET2
V2SET1
ISET1
V1SET2
PGND
V1SET1
18 19 20 21 22 23 24 25
The bias supply input for the small signal circuitry. Connect this
pin to the highest supply voltage available if two or more
options are available. Locally filter this pin using a low ESL
ceramic capacitor of 1µF or larger, and a 10 resistor.
PVIN1, PVIN2, PVIN3, PVIN4, PVIN5, PVIN6
These pins are the power supply pins for the corresponding
PWM power blocks. Associated power blocks must all tie to the
same power supply. The power supply must fall in the range of
3V to 5.5V.
GND
Signal ground. All small signal components connect to this
ground, which in turn connects to PGND at one point.
PGND
Power ground for the PWM power blocks and thermal relief for
the package. The exposed pad must be connected to PGND
and soldered to the PCB. Connect these pins closely to the
negative terminal of input and output capacitors.
FB1, FB2
Voltage feedback input. Depending on the voltage selection pin
settings, connect an optional resistor divider between VOUT
and GND for selection of a variable output voltage.
LX1, LX2, LX3, LX4, LX5, LX6
Switch node connection to inductor. This pin connects to the
internal synchronous power MOSFET switches. The average
voltage of this node is equal to the regulator output voltage.
FN6340 Rev 3.00
March 25, 2008
Page 14 of 22
ISL65426
EN
System enable for voltage monitoring with programmable
hysteresis. This pin has a POR rising threshold of 0.6V. This
enable is intended for applications where two or more input
power supplies are used and bias rise time is an issue.
EN1, EN2
These pins are threshold-sensitive enable inputs for the
individual PWM converters. These pins have low current
(10µA) internal pull-ups to VCC. This pin disables the
respective converter until pulled above a 1V rising threshold.
outlined in Table 1. The controller detects the programmed
configuration based on the state of logic signals at pins ISET1
and ISET2. The controller checks the power block
configuration versus the programmed configuration before the
either converter can soft-start.
Each power block has a separate power supply connection pin,
PVINx, and common channels must join these inputs to one
input power supply. Common synchronous power switch
connection points for each channel must be tied together and
to an external inductor. See the “Typical Application
Schematics” for pin connection guidance.
ISET1, ISET2
Power block configuration inputs. Select the proper state for
each pin according to Table 1.
TABLE 1. POWER BLOCK CONFIGURATION
CHANNEL 1
ISET1 ISET2 IOUT1 CONNECTIONS IOUT2
CHANNEL 2
CONNECTIONS
V1SET1, V1SET2, V2SET1, V2SET2
1
1
3A
LX1,LX2,LX3
3A
LX4,LX5,LX6
Output voltage configuration inputs. Select the proper state of
each pin per the “Electrical Specifications” table.
1
0
4A
LX1,LX2,LX3,LX4
2A
LX5,LX6
0
1
5A
LX1,LX2,LX3,
LX4,LX6
1A
LX5
Power-good output. Open drain logic output that is pulled to
ground when the output voltage is outside regulation limits.
0
0
2A
LX1,LX2
4A
LX3,LX4,LX5,LX6
Functional Description
X
PG1, PG2
The ISL65426 is a monolithic, constant frequency, currentmode dual output buck converter controller with user
configurable power blocks. Designed to provide a total DC/DC
solution for FPGAs, CPLDs, core processors, and ASICs.
PVIN1
POWER BLOCK 1
POWER BLOCK 6
LX1
LX6
PVIN2
LX2
PVIN3
PVIN6
POWER BLOCK 2
POWER BLOCK 5
PVIN5
LX5
POWER BLOCK 3
POWER BLOCK 4
LX3
PVIN4
LX4
MASTER POWER BLOCK
FLOATING POWER BLOCK
FIGURE 35. POWER BLOCK DIAGRAM
Power Blocks
A unique power block architecture allows partitioning of six 1A
capable modules to support one of four power block
configuration options. The block diagram in Figure 3 provides a
top level view of the power block layout. One master power
block is assigned to each converter output channel. Power
Block 2 is allotted to converter Channel 1 and Power Block 5 to
Channel 2. The master power blocks must not be tied together
or the controller will not soft-start. The remaining four floating
power blocks can be partitioned in one of four valid states
FN6340 Rev 3.00
March 25, 2008
Invalid LX Configurations: SS Prevented
X
1A
LX2
5A
LX1,LX3,LX4,
LX5,LX6
Each power block has a scaled pilot device providing current
feedback. The configuration pin settling determines how the
controller handles separation and summing of the individual
current feedback signals.
Main Control Loop
The ISL65426 is a monolithic, constant frequency,
current mode step-down DC/DC converter. During normal
operation, the internal top power switch is turned on at the
beginning of each clock cycle. Current in the output inductor
ramps up until the current comparator trips and turns off the top
power MOSFET. The bottom power MOSFET turns on and the
inductor current ramps down for the rest of the cycle.
The current comparator compares the output current at the
ripple current peak to a current pilot. The error amplifier
monitors VOUT and compares it with the internal voltage
reference. The error amplifier’s output voltage drives a
proportional current to the pilot. If VOUT is low the pilot’s
current level is increased and the trip off current level of the
output is increased. The increased current works to raise the
VOUT level into agreement with the voltage reference.
Output Voltage Programming
The feedback voltage applied to the inverting input of the error
amplifier is scaled internally relative to the 0.6V internal
reference voltage based on the state of logic signals at pins
V1SET1, V1SET2, V2SET1 and V2SET2. The output voltage
configuration logic decodes the 2-bit voltage identification
codes into one of the discrete voltages shown in Table 2. When
each pin is pulled to GND by an internal 10µA pull-down, this
Page 15 of 22
ISL65426
default condition programs the output voltage to the lowest
level. The pull-down prevents situations where a pin could be
left floating for example (cold solder joint) from causing the
output voltage to rise above the programmed level and
damage a sensitive load device.
TABLE 2. OUTPUT VOLTAGE PROGRAMMING
VOUT1
V1SET1
V1SET2
VOUT2
V2SET1
V2SET2
1.8V
1
1
3.3V
1
1
1.5V
0
1
2.5V
0
1
1.2V
1
0
1.8V
1
0
ISL65426
LX
EXTERNAL CONDITIONS
LOUT
VOUT
1.4V
R1
13.3k
FB
R2
10k
FIGURE 36. EXTERNAL OUTPUT VOLTAGE SELECTION
For designers requiring an output voltage level outside those
shown in Table 2, the ISL65426 allows user programming with
an external resistor divider (see Figure 36). First, both channel
selection pins associated with that output channel must be tied
to GND to set the internal reference to 0.6V. Next, the output
voltage is set by an external resistive divider according to
Equation 1. R2 is selected arbitrarily, but 5k or 10k is usually
a good starting point. The designer can configure the output
voltage from 1V to 4V from a 5V power supply. Lower input
supply voltages reduce the maximum programmable output
voltage to 80% of the input voltage level.
(EQ. 1)
Switching Frequency
The controller features an internal oscillator running at a fixed
frequency of 1MHz. The oscillator tolerance is +20% over input
bias and load range.
Operation Initialization
The ISL65426 initializes based on the state of three enable
inputs (EN, EN1, EN2) and power-on reset (POR) monitors on
VCC and PVINx inputs. Successful initialization of the
controller prompts a one time power block configuration check.
Verification of proper phase connections lead to a soft-start
interval. The controller begins slowly ramping the output
voltages based on the enable input states. Once the
commanded output voltage is within the proper window of
operation, the power-good signal corresponding to the active
FN6340 Rev 3.00
March 25, 2008
Power-On Reset
The POR circuitry prevents the controller from attempting to
soft-start before sufficient bias is present at vital power supply
input pins. These include the VCC and PVINx pins.
The VCC pins have a variable POR threshold based on the
output voltage configuration pin configuration of VOUT2. If the
configuration pins are set for 2.5V, the VCC POR rising
threshold is typically 2.9V. The 3.3V configuration increases
the VCC POR level to 4.3V. This variable rising threshold
guarantees that the controller can properly switch the internal
power blocks at the assigned output voltage levels.
The PVINx pins have a set POR rising threshold for all output
voltage configurations. While the voltage on these pins are
below this threshold (as defined in the “Electrical
Specifications” table), the controller inhibits switching of the
internal power MOSFETs.
COUT
V OUT – 0.6V
R 1 = R 2 ---------------------------------0.6V
channel changes state from low to high indicating proper
operation initialization.
Built-in hysteresis between the rising and falling thresholds
insures that once enabled, the controller will not inadvertently
toggle turn off unless the bias voltage drops substantially.
While these pins are below the POR rising threshold, the
synchronous power switch LX pins are held in a highimpedance state.
If additional POR control is required, a system enable input can
be used to govern initialization, as described in the following
section.
Enable and Disable
If the POR input requirements are met, the ISL65426 remains
in shutdown until the voltage at the enable inputs rise above
their enable thresholds. Independent enable inputs, EN1 and
EN2, allow initialization of either buck converter channel
separately, sequenced, or simultaneously. Both pins feature a
10µA pull-up, which will initialize both sides once the voltage at
their respective pins exceeds the rising enable threshold, as
defined in the “Electrical Specifications” table.
Both converters are governed by the presence of a system
enable, EN. When two separate input supplies are used for
each channel of power blocks or an external signal needs to
govern the power-up sequence, the system enable provides a
start-up sequencing mechanism.
The system enable features an internal 11µA pull-down, which
is only active when the voltage on the EN pin is below the
enable threshold. The current sink pulls the EN pin low. As
VCC2 rises, the enable level is not set exclusively by the
resistor divider from VCC2. With the current sink active, the
enable level is defined in Equation 2. R1 is the resistor EN to
VCC2 and R2 is the resistor from EN to GND.
0.6V
V ENABLE = R 1 ------------ + 10A + 0.6V
R2
(EQ. 2)
Page 16 of 22
ISL65426
Once the voltage at the EN pin reaches the enable threshold,
the 10µA current sink turns off.
power block has a pull-down active only during the configuration
check to remove noise related false positive detections.
With the part enabled and the current sink off, the disable level
is set by the resistor divider. The disable level is defined in
Equation 3.
A successful configuration check initiates a soft-start interval
100µs after completion. Failing the configuration check, the
controller will attempt a configuration check again 100µs after
completing the first check cycle. The controller repeats the
configuration check cycle every 100µs until a valid
configuration is detected or the controller is powered down.
Once successful, the configuration check is not implemented
again until VCC falls below the POR falling threshold.
Re-enabling the controller after a successful configuration
check will immediately initiate a soft-start interval.
R1 + R2
V DISABLE = 0.6V --------------------R2
(EQ. 3)
The difference between the enable and disable levels provides
the user with configurable hysteresis to prevent premature
tripping.
To enable the controller, the system enable must be high, and
one or both of the channel enables must be high. The POR
circuitry must be satisfied for both VCC and PVINx inputs.
Once these conditions are met, the controller immediately
initiates a power block configuration check.
ISL65426
EXTERNAL CONDITIONS
+VCC1
+VCC2
R1
EN
+
R2
-
POR
LOGIC
10µA
0.6V
FIGURE 37. SYSTEM ENABLE INPUT
Power Block Configuration Check
After VCC exceeds its POR rising threshold, the controller
decodes ISET1 and ISET2 states into one of four valid power
block configurations (see Table 1). These pins are not checked
again unless VCC falls below the POR falling threshold. The
valid configuration is saved for comparison with the LX slave
connectivity result, which is determined during the
configuration check.
Once the POR and enable circuitry is satisfied, the controller
initiates a configuration check. The master power block of output
Channel 1 (Power Block 2) pulses high for 100ns. The
configuration check circuitry detects which power blocks share a
common LX connection and compares this to the decoded valid
configuration. The master power block of output Channel 2
(Power Block 5) pulses, and again, the LX pins of the other nonmaster blocks are monitored. The common LX connections are
checked versus the decoded valid configuration. Each floating
FN6340 Rev 3.00
March 25, 2008
Once the controller is enabled and power block configuration is
successful, the digital soft-start function clamps the error
amplifier reference. The digital soft-start circuitry ramps the
output voltage by stepping the reference up gradually over a
fixed interval of 4ms. The controlled ramp of the output voltage
reduces the in-rush current during startup.
Power-good Signal
VCC
SYSTEM ENABLE
COMPARATOR
Soft-start Interval
Each power-good pin (PG1, PG2) is an open-drain logic output
that indicates when the converter output voltage is within
regulation limits. The power-good pins pull low during
shutdown and remain low when the controller is enabled. After
a successful converter channel soft-start, the power-good pin
signal associated with that channel releases and the powergood pin voltage rises with an external pull-up resistor. The
power-good signal transitions low immediately upon the
removal of individual channel or system enable.
The power-good circuitry monitors both output voltage FB pins
and compares them to the rising and falling limits shown in the
“Electrical Specifications” table. If either channel’s feedback
voltage exceeds the typical rising limit of 115% of the reference
voltage, the power-good pin pulls low. The power-good pin
continues to pull low until the feedback voltage recovers down
by a typical of 110% of the reference voltage. If either channel’s
feedback voltage drops below a typical of 85% of the reference
voltage, the power-good pin related to the offending channel(s)
pulls low. The power-good pin continues to pull low until the
feedback voltage rises to within 90% of the reference voltage.
The power-good pin then releases and signals the return of the
output voltage within the power-good window.
Fault Monitoring and Protection
The ISL65426 actively monitors output voltage and current to
detect fault conditions. Fault monitors trigger protective
measures to prevent damage to the controller and external
load device. Individual power-good indicators provide options
for linking to external system monitors.
Undervoltage Protection
Separate hysteretic comparators monitor the feedback pin (FB)
of each converter channel. The feedback voltage is compared
Page 17 of 22
ISL65426
This hiccup mode continues indefinitely until both outputs softstart successfully.
to a set undervoltage (UV) threshold based on the output
voltage selected. Once one of the comparators trip indicating a
valid UV condition, a 4-bit UV counter increments. If both
channel comparators detect an UV condition during the same
switching cycle, the 4-bit counter increments twice. Once the 4bit counter overflows, the UV protection logic shuts down both
regulators.
Thermal Monitor
The comparator is reset if the feedback voltage rises back up
above the UV threshold plus a specified amount of hysteresis
outlined in the “Electrical Specifications” table. If both converter
channels experience an UV condition and one rises back
within regulation, then the counter continues to progress
toward overflow.
Thermal-overload protection limits total power dissipation in
the ISL65426. An internal thermal sensor monitors die
temperature continuously. If controller junction temperature
exceeds +150°C, the thermal monitor commands the POR
circuitry to shutdown both channels and latch-off. The POR
latch is reset by cycling VCC to the controller.
Overvoltage Response
Component Selection Guide
If the output voltage exceeds the overvoltage (OV) level for the
power-good signal, the controller will fight this condition by
actively trying to regulate the output voltage back down to the
reference level. This method of fighting the rise in output
voltage is limited by the reverse current capability of the total
number of power blocks associated with the output. The
approximate reverse current capability of each power block is
0.5A. The power-good signal will drop indicating the output
voltage is out of specification. This signal will not transition high
again until the output voltage has dropped below the falling
PGOOD OV threshold.
This design guide is intended to provide a high-level
explanation of the steps necessary to create a power
converter. It is assumed that the reader is familiar with many of
the basic skills and techniques referenced in the following. In
addition to this guide, Intersil provides a complete reference
design that includes schematics, a bill of materials and
example board layout.
Overcurrent Protection
A pilot device is integrated into the upper device structure of
each master power block. The pilot device samples current
through the master power block upper device each cycle. This
channel current feedback is scaled based on the state of the
ISET1 and ISET2 pins. The channel current information is
compared to an overcurrent (OC) limit based on the power block
configuration. Each 1A power block tied to the master power
block increases the OC limit by 2A. For example, if both masters
have two slaves associated with each of them then the OC limit
for each output is 6A for a 3A configuration.
If the sampled current exceeds the OC threshold, a 4-bit OC
up/down counter increments by one LSB. If the sampled current
falls below the OC threshold before the counter overflows, the
counter is reset. If both regulators experience an OC event
during the same cycle, the counter increments twice. Once the
OC counter reaches 1111, both channels are shutdown. If both
channels fall below the overcurrent limit during the same cycle,
the OC counter is reset.
Once in shutdown, the controller enters a delay interval,
equivalent to the SS interval, allowing the die to cool. The OC
counter is reset entering the delay interval. The protection logic
initiates a normal SS internal once the delay interval ends. If
the outputs both successfully soft-start, the power-good signal
goes high and normal operation continues. If OC conditions
continue to exist during the SS interval, the OC counter must
overflow before the controller shutdowns both outputs again.
FN6340 Rev 3.00
March 25, 2008
Note: It is recommended to add a Schottky diode of adequate
rating from LX1 to PGND and from LX5 to PGND to avoid
severe negative ringing that can disturb the OC counter.
Output Filter Design
The output inductor and the output capacitor bank together
form a low-pass filter responsible for smoothing the pulsating
voltage at the phase node. The output filter also must provide
the transient energy until the regulator can respond. Due to its
inherent low bandwidth as compared to the switching
frequency, the output filter limits the system transient response.
The output capacitors must supply or sink load current while
the current in the output inductors increases or decreases to
meet the demand.
OUTPUT CAPACITOR SELECTION
The critical load parameters in choosing the output capacitors are
the maximum size of the load step (I), the load-current slew rate
(di/dt), and the maximum allowable output voltage deviation under
transient loading (VMAX). Capacitors are characterized
according to their capacitance, ESR (Equivalent Series
Resistance), and ESL (Equivalent Series Inductance).
At the beginning of the load transient, the output capacitors supply
all of the transient current. The output voltage will initially deviate
by an amount approximated by the voltage drop across the ESL.
As the load current increases, the voltage drop across the ESR
increases linearly until the load current reaches its final value.
Neglecting the contribution of inductor current and regulator
response, the output voltage initially deviates by an amount
shown in Equation 4.
di
V ESL ----- + ESR I
dt
(EQ. 4)
The filter capacitors selected must have sufficiently low ESL
and ESR so that the total output voltage deviation V is less
than the maximum allowable ripple.
Page 18 of 22
ISL65426
The recommended load capacitance can be estimated using
Equation 5.
1.8V
C OUT = 0.5 Number of LX channels used 150F ---------------V OUT
(EQ. 5)
The internal compensation scheme assumes low-ESR output
capacitors. It is recommended to only use specialty polymer or
ceramic capacitors with ESRs of 10m or lower. Care also
needs to be taken to ensure that the dielectric of the capacitor
used will work reliably in the entire temperature range of the
application.
Design Example:
Consider an output voltage of 1.2V, with LX1, LX2, LX3 and
LX4 connected. The output capacitance required would be:
1.8V
C OUT = 0.5 4 150F ------------ = 450F
1.2V
(EQ. 6)
A 330µF specialty polymer capacitor in parallel with three 47µF
X7R ceramic capacitors would be the recommended choice of
output filter.
Once the output capacitors are selected, the maximum
allowable ripple voltage, VPPMAX, determines the lower limit
on the inductance. See Equation 7.
(EQ. 7)
MAX
Since the output capacitors are supplying a decreasing portion
of the load current while the regulator recovers from the
transient, the capacitor voltage becomes slightly depleted. The
output inductors must be capable of assuming the entire load
current before the output voltage decreases more than VMAX.
This places an upper limit on inductance.
Equation 8 gives the upper limit on output inductance for the
cases when the trailing edge of the current transient causes
the greater output voltage deviation than the leading edge.
Equation 9 addresses the leading edge. Normally, the trailing
edge dictates the inductance selection because duty cycles
are usually less than 50%. Nevertheless, both inequalities
should be evaluated, and inductance should be governed
based on the lower of the two results. In each equation, L is the
output inductance and C is the total output capacitance.
2 C VO
L ------------------------- V MAX – I ESR
I 2
(EQ. 8)
1.25 C
L ------------------------- V MAX – I ESR V IN – V O
I 2
(EQ. 9)
The other concern when selecting an output inductor is the
internally set current mode slope compensation. Designs
should not allow inductor ripple currents below 0.125 times the
maximum output current to prevent regulation issues.
FN6340 Rev 3.00
March 25, 2008
V – V
V
IN
OUT OUT
L @ ---------------------------------------------------------------I
OUT
MAX
V f ----------------------------IN
s
3
(EQ. 10)
Input Capacitor Selection
Input capacitors are responsible for sourcing the AC
component of the input current flowing into the switching power
devices. Their RMS current capacity must be sufficient to
handle the AC component of the current drawn by the
switching power devices, which is related to duty cycle. The
maximum RMS current required by the regulator is closely
approximated by Equation 11.
I
RMS MAX
=
V OUT
V IN – V OUT V OUT 2
2 1
----------------- I
+ ------ ---------------------------------- -----------------
OUT
V IN
V IN
12
L fs
MAX
(EQ. 11)
OUTPUT INDUCTOR SELECTION
V IN – V OUT V OUT
L ESR ----------------------------------------------------f s V IN V PP
It is recommended to use a 30% peak-to-peak ripple current
value to calculate out the inductance required for the
application. Accordingly, the inductance estimated using
Equation 10 below would fall between the minimum inductance
value calculated in Equation 7 and the maximum values
determined from Equations 8 and 9.
The important parameters to consider when selecting an input
capacitor are the voltage rating and the RMS current rating.
For reliable operation, select capacitors with voltage ratings
above the maximum input voltage. The rated voltage rating
should be at least 1.25 times greater than the maximum input
voltage while using aluminum electrolytic capacitors, and about
2 times the maximum input voltage to account for capacitance
derating in case of ceramic capacitors. The capacitor RMS
current rating should be higher than the largest RMS current
required by the circuit.
The ISL65426 needs a minimum effective input capacitance of
70µF with low ESR for stable operation.
Layout Considerations
Careful printed circuit board (PCB) layout is critical in high
frequency switching converter design. Current transitions from
one device to another at this frequency induce voltage spikes
across the interconnecting impedances and parasitic
elements. These spikes degrade efficiency, lead to device
overvoltage stress, radiate noise into sensitive nodes, and
increase thermal stress on critical components. Careful
component placement and PCB layout minimizes the voltage
spikes in the converter.
The following multi-layer printed circuitry board layout
strategies minimize the impact of board parasitics on converter
performance and optimize the heat-dissipating capabilities of
the printed circuit board. This section highlights some
important practices which should not be overlooked during the
layout process. Figure 38 provides a top level view of the
critical components, layer utilization, and signal routing for
reference.
Page 19 of 22
ISL65426
Component Placement
Determine the total implementation area and orient the critical
switching components first. These include the controller, input
and output capacitors, and the output inductors. Symmetry is
very important in determining how available space is filled and
depends on the power block configuration selected. The
controller must be placed equidistant from each output stage
with the LX or phase connection distance minimized.
An output stage consists of the area reserved for the output
inductor, and input capacitors, and output capacitors for a
single channel. Place the inductor such that one pad is a
minimal distance from the associated phase connection. Orient
the inductor such that the load device is a short distance from
the other pad. Placing the input capacitors a minimal distance
from the PVIN pins prevents long distances from adding too
much trace inductance and a reduction in capacitor
performance. Locate the output capacitors between the
inductor and the load device, while keeping them in close
proximity. Care should be taken not to add inductance through
long trace lengths that could cancel the usefulness of the low
inductance components. Keeping the components in tight
proximity will help reduce parasitic impedances once the
components are routed together.
One additional solid layer is dedicated as a power plane and
broken into smaller islands of common voltage. The power
plane should support the input power and output power nodes.
Use copper filled polygons on the top and bottom circuit layers
for the phase nodes. Use the remaining printed circuit board
layers for small signal wiring and additional power or ground
islands as required.
Signal Routing
If the output stage component placement guidelines are
followed, stray inductance in the switch current path is
minimized along with good routing techniques. Great attention
should be paid to routing the PHASE plane since high current
pulses are driven through them. Stray inductance in this highcurrent path induces large noise voltages that couple into
sensitive circuitry. By keeping the PHASE plane small, the
magnitude of the potential spikes is minimized. It is important
to size traces from the LX pins to the PHASE plane as large
and short as possible to reduce their overall impedance and
inductance.
Bypass capacitors, CBP, supply critical filtering and must be
placed close to their respective pins. Stray trace parasitics will
reduce their effectiveness, so keep the distance between the
VCC bias supply pad and capacitor pad to a minimum.
Plane Allocation
PCB designers typically have a set number of planes available
for a converter design. Dedicate one solid layer, (usually an
internal layer underneath the component side of the board), for
a ground plane and make all critical component ground
connections with vias to this layer.
VIN
VIN
KEY
THICK TRACE ON CIRCUIT PLANE LAYER
PVIN
VCC
ISLAND ON CIRCUIT PLANE LAYER
CIN
CBP
ISLAND ON POWER PLANE LAYER
VIA CONNECTION TO GROUND PLANE
PHASE
ISL65426
LOUT
VOUT
LX
COUT
GND
CHFOUT
LOAD
FB
PGND
FIGURE 38. PRINTED CIRCUIT BOARD POWER PLANES AND ISLANDS
FN6340 Rev 3.00
March 25, 2008
Page 20 of 22
ISL65426
Sensitive signals should be routed on different layers or some
distance away from the PHASE plane on the same layer.
Crosstalk due to switching noise is reduced into these lines by
isolating the routing path away from the PHASE plane. Layout
the PHASE planes on one layer, usually the top or bottom
layer, and route the voltage feedback traces on another
remaining layer.
Thermal Management
For maximum thermal performance in high current, high
switching frequency applications, connecting the thermal
PGND pad of the ISL65426 to the ground plane with multiple
vias is recommended. This heat spreading allows the IC to
achieve its full thermal potential. If possible, place the
controller in a direct path of any available airflow to improve
thermal performance.
© Copyright Intersil Americas LLC 2006-2008. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6340 Rev 3.00
March 25, 2008
Page 21 of 22
ISL65426
L50.5x10
50 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 0, 7/06
5.00
0.10 M C A B
0.05 M C
A
B
4
0.25
0.50
43
A
PIN 1 INDEX AREA
(C 0.40)
50
42
1
26
17
9.20
0.50x16=8.00 REF
0.50
8.10
10.00
PIN 1
INDEX AREA
0.15 (4X)
A
25
18
VIEW "A-A"
0.40±0.10
3.30
0.50x7=3.50 REF
0.40±0.10
TOP VIEW
4.20
BOTTOM VIEW
SEE DETAIL "X"
0.10 C
C
SEATING PLANE
0.08 C
SIDE VIEW
MAX. 1.00
9.80
C
8.10
0.2 REF
5
0.00 MIN.
0.05 MAX.
(46 x 0.50)
DETAIL "X"
(50 x 0.25)
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MM.
(50 x 0.60)
3.30
4.80
RECOMMENDED LAND PATTERN
FN6340 Rev 3.00
March 25, 2008
2. UNLESS OTHERWISE SPECIFIED TOLERANCE : DECIMAL ±0.05
ANGULAR ±2×
3. DIMENSIONING AND TOLERANCE PER ASME Y 14.5M-1994.
4. DIMENSION LEAD WIDTH APPLIES TO THE PLATED TERMINAL
AND IS MEASURED BETWEEN 0.23MM AND 0.28MM FROM
THE TERMINAL TIP.
5. TIEBAR SHOWN (if present) IS A NON-FUNCTIONAL FEATURE
Page 22 of 22