ISL6610, ISL6610A
®
Data Sheet
Dual Synchronous Rectified MOSFET
Drivers
The ISL6610, ISL6610A integrates two ISL6609, ISL6609A
drivers with enable function removed and is optimized to
drive two independent power channels in a synchronousrectified buck converter topology. These drivers, combined
with an Intersil ISL63xx or ISL65xx multiphase PWM
controller, form a complete high efficiency voltage regulator
at high switching frequency.
The IC is biased by a single low voltage supply (5V),
minimizing driver switching losses in high MOSFET gate
capacitance and high switching frequency applications.
Each driver is capable of driving a 3nF load with less than
10ns rise/fall time. Bootstrapping of the upper gate driver is
implemented via an internal low forward drop diode,
reducing implementation cost, complexity, and allowing the
use of higher performance, cost effective N-Channel
MOSFETs. Adaptive shoot-through protection is integrated
to prevent both MOSFETs from conducting simultaneously.
The ISL6610, ISL6610A features 4A typical sink current for
the lower gate driver, enhancing the lower MOSFET gate
hold-down capability during PHASE node rising edge,
preventing power loss caused by the self turn-on of the lower
MOSFET due to the high dV/dt of the switching node.
The ISL6610, ISL6610A also features an input that
recognizes a high-impedance state, working together with
Intersil multiphase PWM controllers to prevent negative
transients on the controlled output voltage when operation is
suspended. This feature eliminates the need for the schottky
diode that may be utilized in a power system to protect the
load from negative output voltage damage.
In addition, the ISL6610As bootstrap function is designed to
prevent the BOOT capacitor from overcharging, should
excessively large negative swings occur at the transitions of
the PHASE node.
November 22, 2006
FN6395.0
Features
• 5V Quad N-Channel MOSFET Drives for Two
Synchronous Rectified Bridges
• Pin-to-pin Compatible with ISL6614 (12V Drive)
• Adaptive Shoot-Through Protection
• 0.4Ω On-Resistance and 4A Sink Current Capability
• Supports High Switching Frequency
- Fast Output Rise and Fall
- Low Tri-State Hold-Off Time
• BOOT Capacitor Overcharge Prevention (ISL6610A)
• Low VF Internal Bootstrap Diode
• Power-On Reset
• QFN Package
- Compliant to JEDEC PUB95 MO-220 QFN-Quad Flat
No Leads-Product Outline
- Near Chip-Scale Package Footprint; Improves PCB
Utilization, Thinner Profile
• Pb-Free Plus Anneal Available (RoHS Compliant)
Related Literature
• Technical Brief TB389 “PCB Land Pattern Design and
Surface Mount Guidelines for QFN (MLFP) Packages”
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
Ordering Information
PART
NUMBER
(Note)
TEMP.
RANGE
(°C)
PART
MARKING
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL6610CBZ
6610CBZ
0 to +70
14 Ld SOIC
ISL6610CRZ
66 10CRZ
0 to +70
16 Ld 4x4 QFN L16.4x4
ISL6610IBZ
6610IBZ
-40 to +85 14 Ld SOIC
Applications
ISL6610IRZ
66 10IRZ
-40 to +85 16 Ld 4x4 QFN L16.4x4
• Core Voltage Supplies for Intel® and AMD®
Microprocessors
ISL6610ACBZ 6610ACBZ
0 to +70
14 Ld SOIC
ISL6610ACRZ 66 10ACRZ
0 to +70
16 Ld 4x4 QFN L16.4x4
• High Frequency Low Profile High Efficiency DC/DC
Converters
ISL6610AIBZ
6610AIBZ
-40 to +85 14 Ld SOIC
ISL6610AIRZ
66 10AIRZ
-40 to +85 16 Ld 4x4 QFN L16.4x4
• High Current Low Voltage DC/DC Converters
• Synchronous Rectification for Isolated Power Supplies
1
M14.15
M14.15
M14.15
M14.15
Add “-T” suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006. All Rights Reserved
AMD® is a registered trademark of Advanced Micro Devices, Inc. All other trademarks mentioned are the property of their respective owners.
ISL6610, ISL6610A
Pinouts
GND
3
12 UGATE1
LGATE1
4
11 BOOT1
PVCC
5
10 BOOT2
PGND
6
9 UGATE2
LGATE2
7
8 PHASE2
PHASE1
13 PHASE1
16
15
14
13
GND 1
12 UGATE1
LGATE1 2
11 BOOT1
17
GND
PVCC 3
10 BOOT2
PGND 4
9
NC1
5
6
7
8
NC2
2
VCC
PWM2
PHASE2
14 VCC
PWM1
1
LGATE2
PWM1
PWM2
ISL6610, ISL6610A
(16 LD QFN)
TOP VIEW
ISL6610, ISL6610A
(14 LD SOIC)
TOP VIEW
UGATE2
Block Diagram
ISL6610, ISL6610A
RBOOT
PVCC
VCC
BOOT1
UGATE1
4.9K
SHOOTTHROUGH
PROTECTION
PHASE1
CHANNEL 1
PVCC
PWM1
LGATE1
4.6K
PGND
CONTROL
LOGIC
VCC
PVCC
4.9K
PGND
RBOOT
BOOT2
UGATE2
PWM2
SHOOTTHROUGH
PROTECTION
4.6K
GND
PHASE2
CHANNEL 2
PVCC
LGATE2
PGND
PAD
FOR ISL6610CR/10ACR, THE PAD ON THE BOTTOM SIDE OF
THE QFN PACKAGE MUST BE SOLDERED TO THE CIRCUIT’S GROUND.
INTEGRATED 3Ω RESISTOR (RBOOT) AVAILABLE ONLY IN ISL6610A
2
FN6395.0
November 22, 2006
ISL6610, ISL6610A
Typical Application - Multiphase Converter Using ISL6610 Gate Drivers
BOOT1
+5V
+12V
UGATE1
VCC
PHASE1
LGATE1
+5V
DUAL
DRIVER
ISL6610
VCC
VSEN
+5V
BOOT2
COMP
FB
PVCC
+12V
UGATE2
ISEN1
PGOOD
PWM1
EN
PWM2
VID
MAIN ISEN2
CONTROL
ISL65xx
PWM1
PHASE2
NC2
PWM2
LGATE2
NC1
GND
PGND
+VCORE
ISEN3
FS/DIS
PWM3
PWM4
GND
BOOT1
+5V
+12V
ISEN4
UGATE1
VCC
PHASE1
LGATE1
DUAL
DRIVER
ISL6610
PVCC
+5V
BOOT2
+12V
UGATE2
PWM1
PHASE2
PWM2
LGATE2
GND
3
PGND
FN6395.0
November 22, 2006
ISL6610, ISL6610A
Absolute Maximum Ratings
Thermal Information
Supply Voltage (PVCC, VCC) . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
Input Voltage (VEN, VPWM) . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
BOOT Voltage (VBOOT-GND). . . -0.3V to 25V (DC) or 36V (
很抱歉,暂时无法提供与“ISL6610IBZ-T”相匹配的价格&库存,您可以联系我们找货
免费人工找货