0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
ISL6744AUZ-T

ISL6744AUZ-T

  • 厂商:

    RENESAS(瑞萨)

  • 封装:

    TSSOP8

  • 描述:

    IC REG CTRLR MULT TOPOLOGY 8MSOP

  • 数据手册
  • 价格&库存
ISL6744AUZ-T 数据手册
NOT RECOMMENDED FOR NEW DESIGNS PLEASE SEE ISL6744A DATASHEET ISL6744 FN9147 Rev.8.00 September 22, 2005 Intermediate Bus PWM Controller The ISL6744 is a low cost, primary side, double-ended controller intended for applications using full and half-bridge topologies for unregulated DC/DC converters. It is a voltagemode PWM controller designed for half-bridge and fullbridge power supplies. It provides precise control of switching frequency, adjustable soft-start, precise deadtime control with deadtimes as low as 35ns, and overcurrent shutdown. Features Low start-up and operating currents allow for easy biasing in both AC/DC and DC/DC applications. This advanced BiCMOS design features low start-up and operating currents, adjustable switching frequency up to 1MHz, 1A FET drivers, and very low propagation delays for a fast response to overcurrent faults. • Adjustable Soft-Start • Precision Duty Cycle and Deadtime Control • 100µA Start-up Current • Adjustable Delayed Overcurrent Shutdown and Restart • Adjustable Oscillator Frequency Up to 2MHz • 1A MOSFET Gate Drivers • Internal Over Temperature Protection • 35ns Control to Output Propagation Delay • Small Size and Minimal External Component Count • Input Undervoltage Protection Ordering Information PART NUMBER TEMP. RANGE (°C) • Pb-Free Plus Anneal Available (RoHS Compliant) PACKAGE PKG. DWG. # Applications ISL6744AU -40 to 105 8 Ld MSOP M8.118 ISL6744AUZ (Note) -40 to 105 8 Ld MSOP (Pb-free) M8.118 ISL6744AB -40 to 105 8 Ld SOIC M8.15 • Bus Converters ISL6744ABZ (Note) -40 to 105 8 Ld SOIC (Pb-free) M8.15 Pinout Add “-T” suffix for tape and reel. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN9147 Rev.8.00 September 22, 2005 • Telecom and Datacom Isolated Power • DC Transformers ISL6744 (SOIC, MSOP) TOP VIEW SS 1 8 VDD RTD 2 7 OUTB CS 3 6 OUTA CT 4 5 GND Page 1 of 18 VDD FL VBIAS VBIAS 5.00 V VDD ISL6744 FN9147 Rev.8.00 September 22, 2005 Internal Architecture OUTA Q + BG T UVLO Q OUTB PWM TOGGLE VBIAS INTERNAL OT SHUTDOWN 130 - 150 C 70uA GND ON SS VBIAS + - SS CLAMP RTD - 2.0 V IRTD + - + 15 uA SS CHARGED 3.9 V 4.0 V VBIAS 160 uA S Q R Q OC LATCH ON 2.8 V - PEAK + CT - I DCH= 55 x IRTD 0.8 V S Q R Q CLK Q RESET DOMINANT VALLEY + SS LOW Q 50 µS RETRIGGERABLE ONE SHOT FAULT LATCH SET DOMINANT S Q IDCH R Q S Q R Q PWM LATCH SET DOMINANT ON VBIAS UV + BG 0.6 V OC DETECT + - Page 2 of 18 SS COMPARATOR CT + - SS 0.8 SS FL VBIAS 4.65V 4.80V  CS 0.27 V + - SP1 VIN+ +12V QR1 L1 C11 QH QR3 C2 T1 L3 R8 C9 C13 R10 TP1 C8 RTN L2 C1 T2 R9 QR4 QR2 QL R2 C14 CR3 R11 C12 CR2 C3 R1 TP2 CR1 C7 U4 ISL6700 VDD HB LO VSS HO HS LI HI R6 R5 TP4 C10 C4 C5 TP5 U1 SS GND VIN- OUTA VDD R7 ISL6744 OUTB CS CT C18 RTD D2 TP6 Q5 C15 Page 3 of 18 C16 D1 R12 C6 ISL6744 FN9147 Rev.8.00 September 22, 2005 Typical Application using ISL6744 - 48V Input DC Transformer, 12V @ 8A Output ISL6744 Absolute Maximum Ratings Thermal Information Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . GND - 0.3V to +20.0V OUTA, OUTB . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VDD Signal Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to 5V Peak GATE Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1A ESD Classification Human Body Model (Per MIL-STD-883 Method 3015.7) . . .2000V Machine Model (Per EIAJ ED-4701 Method C-111) . . . . . . . .100V Charged Device Model (Per EOS/ESD DS5.3, 4/14/93) . . .1000V Thermal Resistance (Typical, Note 1) JA (°C/W) 8 Lead MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 8 Lead SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Maximum Junction Temperature . . . . . . . . . . . . . . . . -55°C to 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C Operating Conditions Temperature Range ISL6744AU . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 105°C Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . 9-16 VDC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. All voltages are to be measured with respect to GND, unless otherwise specified. Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to Block Diagram and Typical Application schematic. 9V < VD < 16V, RTD = 51.1k, CT = 470pF, TA = -40°C to 105°C (Note 4), Typical values are at TA = 25°C PARAMETER TEST CONDITIONS MIN TYP MAX UNITS SUPPLY VOLTAGE Start-Up Current, IDD VDD < START Threshold - - 175 A Operating Current, IDD RLOAD, COUTA,B = 0 - 2.89 - mA COUTA,B = 1nF - 5 8.5 mA UVLO START Threshold 5.9 6.3 6.6 V UVLO STOP Threshold 5.3 5.7 6.3 V - 0.6 - V 0.55 0.6 0.65 V - 35 - ns CS Sink Current 8 10 - mA Input Bias Current -1 - 1 A Hysteresis CURRENT SENSE Current Limit Threshold CS to OUT Delay (Note 4) PULSE WIDTH MODULATOR Minimum Duty Cycle VERROR < CT Offset - - 0 % Maximum Duty Cycle CT = 470pF, RTD = 51.1k - 94 - % CT = 470pF, RTD = 1.1k(Note 4) - 99 - % CT to SS Comparator Input Gain (Note 4) - 1 - V/V SS to SS Comparator Input Gain (Note 4) - 0.8 - V/V FN9147 Rev.8.00 September 22, 2005 Page 4 of 18 ISL6744 Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to Block Diagram and Typical Application schematic. 9V < VD < 16V, RTD = 51.1k, CT = 470pF, TA = -40°C to 105°C (Note 4), Typical values are at TA = 25°C (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 143 156 170 A 1.925 2 2.075 V 45 - 65 A/A CT Valley Voltage 0.75 0.8 0.85 V CT Peak Voltage 2.70 2.80 2.90 V Charging Current 45 - 68 µA SS Clamp Voltage 3.8 4.0 4.2 V - 3.9 - V 12 15 23 A 0.25 0.27 0.30 V OSCILLATOR Charge Current RTD Voltage Discharge Current Gain SOFT-START Overcurrent Shutdown Threshold Voltage (Note 4) Overcurrent Discharge Current Reset Threshold Voltage (Note 4) OUTPUT High Level Output Voltage (VOH) VDD - VOUTA or VOUTB, IOUT = -100mA - 0.5 2.0 V Low Level Output Voltage (VOL) IOUT = 100mA - 0.5 1.0 V Rise Time CGATE = 1nF, VDD = 12V - 17 60 ns Fall Time CGATE = 1nF, VDD = 12V - 20 60 ns Thermal Shutdown (Note 4) - 145 - °C Thermal Shutdown Clear (Note 4) - 130 - °C Hysteresis, Internal Protection (Note 4) - 15 - °C THERMAL PROTECTION NOTES: 3. Specifications at -40°C are guaranteed by design, not production tested. 4. Guaranteed by design, not 100% tested in production. FN9147 Rev.8.00 September 22, 2005 Page 5 of 18 ISL6744 Typical Performance Curves 1-104 CT = 1000pF 680pF 470pF 60 DEADTIME (ns) CT DISCHARGE CURRENT GAIN 65 55 50 1-103 CT = 270pF CT = 100pF 100 45 40 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 10 RTD CURRENT (mA) 10 FIGURE 1. OSCILLATOR CT DISCHARGE CURRENT GAIN 40 50 60 RTD (k) 70 80 90 100 1.03 NORMALIZED CHARGING CURRENT OSCILLATOR FREQUENCY (kHz) 30 FIGURE 2. DEADTIME vs CAPACITANCE 600 500 400 300 200 100 0 100 20 200 300 400 500 600 CT (pF) 700 800 900 1.02 1.01 1.00 0.99 0.98 0.97 0.96 0.95 -40 1000 -25 -10 5 20 35 50 65 80 95 110 TEMPERATURE (°C) FIGURE 3. CAPACITANCE vs OSCILLATOR FREQUENCY (RTD = 49.9k) FIGURE 4. CHARGE CURRENT vs TEMPERATURE 1.07 NORMALIZED VOLTAGE 1.06 1.05 1.04 1.03 1.02 1.01 1.00 0.99 0.98 0 10 20 30 40 50 60 70 80 90 100 RTD (k) FIGURE 5. TIMING CAPACITOR VOLTAGE vs RTD FN9147 Rev.8.00 September 22, 2005 Page 6 of 18 ISL6744 Pin Descriptions Functional Description VDD - VDD is the power connection for the IC. To optimize noise immunity, bypass VDD to GND with a ceramic capacitor as close to the VDD and GND pins as possible. The total supply current, IDD, will be dependent on the load applied to outputs OUTA and OUTB. Total IDD current is the sum of the quiescent current and the average output current. Knowing the operating frequency, Fsw, and the output loading capacitance charge, Q, per output, the average output current can be calculated from: I OUT = 2  Q  Fsw (EQ. 1) RTD - This is the oscillator timing capacitor discharge current control pin. A resistor is connected between this pin and GND. The current flowing through the resistor determines the magnitude of the discharge current. The discharge current is nominally 55x this current. The PWM deadtime is determined by the timing capacitor discharge duration. CT - The oscillator timing capacitor is connected between this pin and GND. CS - This is the input to the overcurrent protection comparator. The overcurrent comparator threshold is set at 0.600V nominal. The CS pin is shorted to GND at the end of each switching cycle. Depending on the current sensing source impedance, a series input resistor may be required due to the delay between the internal clock and the external power switch. Exceeding the overcurrent threshold will start a delayed shutdown sequence. Once an overcurrent condition is detected, the soft-start charge current source is disabled. The soft-start capacitor begins discharging through a 15µA current source, and if it discharges to less than 3.9V (Sustained Overcurrent Threshold), a shutdown condition occurs and the OUTA and OUTB outputs are forced low. When the soft-start voltage reaches 0.27V (Reset Threshold) a soft-start cycle begins. If the overcurrent condition ceases, and then an additional 50µs period elapses before the shutdown threshold is reached, no shutdown occurs. The SS charging current is re-enabled and the soft-start voltage is allowed to recover. GND - Reference and power ground for all functions on this device. Due to high peak currents and high frequency operation, a low impedance layout is necessary. Ground planes and short traces are highly recommended. OUTA and OUTB - Alternate half cycle output stages. Each output is capable of 1A peak currents for driving power MOSFETs or MOSFET drivers. Each output provides very low impedance to overshoot and undershoot. SS - Connect the soft-start timing capacitor between this pin and GND to control the duration of soft-start. The value of the capacitor determines the rate of increase of the duty cycle during start-up, controls the overcurrent shutdown delay, and the overcurrent and short circuit hiccup restart period. FN9147 Rev.8.00 September 22, 2005 Features The ISL6744 PWM is an excellent choice for low cost bridge topologies for applications requiring accurate frequency and deadtime control. Among its many features are 1A FET drivers, adjustable soft-start, overcurrent protection and internal thermal protection, allowing a highly flexible design with minimal external components. Oscillator The ISL6744 has an oscillator with a frequency range to 2MHz, programmable using a resistor RTD and capacitor CT. The switching period may be considered to be the sum of the timing capacitor charge and discharge durations. The charge duration is determined by CT and the internal current source (assumed to be 160A in the formula). The discharge duration is determined by RTD and CT. 4 T C  1.25 10  C T s (EQ. 2) 1 T D  -----------------------------------------------------------------------------  R TD  C T CTDisch arg eCurrentGain 1 T OSC = T C + T D = ---------------F OSC s s (EQ. 3) (EQ. 4) where TC and TD are the approximate charge and discharge times, respectively, TOSC is the oscillator free running period, and FOSC is the oscillator frequency. One output switching cycle requires two oscillator cycles. The actual times will be slightly longer than calculated due to internal propagation delays of approximately 5ns/transition. This delay adds directly to the switching duration, and also causes overshoot of the timing capacitor peak and valley voltage thresholds, effectively increasing the peak-to-peak voltage on the timing capacitor. Additionally, if very low charge and discharge currents are used, there will be an increased error due to the input impedance at the CT pin. The above formulae help with the estimation of the frequency. Practically, effects like stray capacitances that affect the overall CT capacitance, variation in RTD voltage and charge current over temperature, etc. exist, and are best evaluated in-circuit. Equation 2 follows from the basic dV capacitor current equation, i = C  . In this case, with dt variation in dV with RTD (Figure 5), and in charge current (Figure 4), results from Equation 2 would differ from the calculated frequency. The typical performance curves may be used as a tool along with the above equations as a more accurate tool to estimate the operating frequency more accurately. The maximum duty cycle, D, and deadtime, DT, can be calculated from: D = T C  T OSC DT =  1 – D   T OSC (EQ. 5) s (EQ. 6) Page 7 of 18 ISL6744 Soft-Start Operation Typical Application The ISL6744 features a soft-start using an external capacitor in conjunction with an internal current source. Soft-start reduces stresses and surge currents during start-up. The Typical Application Schematic features the ISL6744 in an unregulated half-bridge DC/DC converter configuration, often referred to as a DC Transformer or Bus Converter. The oscillator capacitor signal, CT, is compared to the soft-start voltage, SS, in the SS comparator which drives the PWM latch. While the SS voltage is less than 3.5V, duty cycle is limited. The output pulse width increases as the soft-start capacitor voltage increases up to 3.5V. This has the effect of increasing the duty cycle from zero to the maximum pulse width during the soft-start period. When the soft-start voltage exceeds 3.5V, soft-start is completed. Soft-start occurs during start-up and after recovery from an overcurrent shutdown. The soft-start voltage is clamped to 4V. The input voltage is 48V ±10% DC. The output is a nominal 12V when the input voltage is at 48V. Since this is an unregulated topology, the output voltage will vary proportionately with input voltage. The load regulation is a function of resistance between the source and the converter output. The output is rated at 8A. Gate Drive Half-Bridge Capacitors: C2, C3 The ISL6744 is capable of sourcing and sinking 1A peak current, and may also be used in conjunction with a MOSFET driver such as the ISL6700 for level shifting. To limit the peak current through the IC, an external resistor may be placed between the totem-pole output of the IC (OUTA or OUTB pin) and the gate of the MOSFET. This small series resistor also damps any oscillations caused by the resonant tank of the parasitic inductances in the traces of the board and the FET’s input capacitance. Overcurrent Operation Circuit Elements The converter design is comprised of the following functional blocks: Input Filtering: L1, C1, R1 Isolation Transformer: T1 Primary Snubber: C13, R10 Start Bias Regulator: CR3, R2, R7, C6, Q5, D1 Supply Bypass Components: C15, C4 Main MOSFET Power Switch: QH, QL Current Sense Network: T2, CR1, CR2, R5, R6, R11, C10, C14 Overcurrent delayed shutdown is enabled once the soft-start cycle is complete. If an overcurrent condition is detected, the soft-start charging current source is disabled and the softstart capacitor is allowed to discharge through a 15µA source. At the same time a 50µs retriggerable one-shot timer is activated. It remains active for 50µs after the overcurrent condition ceases. If the soft-start capacitor discharges to 3.9V, the output is disabled. This state continues until the soft-start voltage reaches 270mV, at which time a new softstart cycle is initiated. If the overcurrent condition stops at least 50µs prior to the soft-start voltage reaching 3.9V, the soft-start charging currents revert to normal operation and the soft-start voltage is allowed to recover. Control Circuit: U1, C18, C16, D2 Thermal Protection Switching Frequency, Fsw: 235kHz Output Rectification and Filtering: QR1, QR2, QR3, QR4, L2, C9, C8 Secondary Snubber: R8, R9, C11, C12 FET Driver: U4 Bootstrap components for driver: CR4, C5 ZVS Resonant Delay (Optional): L3, C7 Design Specifications The following design requirements were selected for evaluation purposes: An internal temperature sensor protects the device should the junction temperature exceed 145°C. There is approximately 15°C of hysteresis. VOUT: 12V (nominal) Ground Plane Requirements IOUT: 8A (steady state) Careful layout is essential for satisfactory operation of the device. A good ground plane must be employed. VDD should be bypassed directly to GND with good high frequency capacitance. POUT: 100W FN9147 Rev.8.00 September 22, 2005 VIN: 48 ± 10% V Efficiency: 95% Ripple: 1% Page 8 of 18 ISL6744 nSR nS nP nS nSR FIGURE 6. TRANSFORMER SCHEMATIC Transformer Design The design of a transformer for a half-bridge application is a straightforward affair, although iterative. It is a process of many compromises, and even experienced designers will produce different designs when presented with identical requirements. The iterative design process is not presented here for clarity. The abbreviated design process follows: • Select a core geometry suitable for the application. Constraints of height, footprint, mounting preference, and operating environment will affect the choice. • Determine the turns ratio. • Select suitable core material(s). • Select maximum flux density desired for operation. • Select core size. Core size will be dictated by the capability of the core structure to store the required energy, the number of turns that have to be wound, and the wire gauge needed. Often the window area (the space used for the windings) and power loss determine the final core size. • Determine maximum desired flux density. Depending on the frequency of operation, the core material selected, and the operating environment, the allowed flux density must be determined. The decision of what flux density to allow is often difficult to determine initially. Usually the highest flux density that produces an acceptable design is used, but often the winding geometry dictates a larger core than is indicated based on flux density alone. • Determine the number of primary turns. • Select the wire gauge for each winding. • Determine winding order and insulation requirements. • Verify the design. For this application we have selected a planar structure to achieve a low profile design. A PQ style core was selected because of its round center leg cross section, but there are many suitable core styles available. Since the converter is operating open loop at nearly 100% duty cycle, the turns ratio, N, is simply the ratio of the input voltage to the output voltage divided by 2. V IN 48 N = ------------------------- = --------------- = 2 V OUT  2 12  2 (EQ. 7) The factor of 2 in the denominator is due to the half-bridge topology. Only half of the input voltage is applied to the primary of the transformer. A PC44HPQ20/6 “E-Core” plus a PC44PQ20/3 “I-Core” from TDK were selected for the transformer core. The ferrite material is PC44. The core parameter of concern for flux density is the effective core cross-sectional area, Ae. For the PQ core pieces selected: Ae = 0.62cm2 or 6.2e -5m2 Using Faraday’s Law, V = N d/dt, the number of primary turns can be determined once the maximum flux density is set. An acceptable Bmax is ultimately determined by the allowable power dissipation in the ferrite material and is influenced by the lossiness of the core, core geometry, operating ambient temperature, and air flow. The TDK datasheet for PC44 material indicates a core loss factor of ~400mW/cm3 with a ± 2000 gauss 100kHz sinusoidal excitation. The application uses a 235kHz square wave excitation, so no direct comparison between the application and the data can be made. Interpolation of the data is required. The core volume is approximately 1.6cm3, so the estimated core loss is f act 3 mW 200kHz P loss  -----------  cm  --------------- = 0.4  1.6  --------------------- = 1.28 3 f meas 100kHz cm W (EQ. 8) 1.28W of dissipation is significant for a core of this size. Reducing the flux density to 1200 gauss will reduce the dissipation by about the same percentage, or 40%. Ultimately, evaluation of the transformer’s performance in the application will determine what is acceptable. From Faraday’s Law and using 1200 gauss peak flux density (B = 2400 gauss or 0.24 tesla) –6 V IN  T ON 53  2  10 N = ------------------------------ = ----------------------------------------------------- = 3.56 –5 2  A e  B 2  6.2  10  0.24 turns (EQ. 9) Rounding up yields 4 turns for the primary winding. The peak flux density using 4 turns is ~1100 gauss. From EQ. 7, the number of secondary turns is 2. The volts/turn for this design ranges from 5.4V at VIN = 43V to 6.6V at VIN = 53V. Therefore, the synchronous rectifier (SR) windings may be set at 1 turn each with proper FET selection. Selecting 2 turns for the synchronous rectifier FN9147 Rev.8.00 September 22, 2005 Page 9 of 18 ISL6744 windings would also be acceptable, but the gate drive losses would increase. The next step is to determine the equivalent wire gauge for the planar structure. Since each secondary winding conducts for only 50% of the period, the RMS current is I RMS = I OUT  D = 10  0.5 = 7.07 A (EQ. 10) where D is the duty cycle. Since an FR-4 PWB planar winding structure was selected, the width of the copper traces is limited by the window area width, and the number of layers is limited by the window area height. The PQ core selected has a usable window area width of 0.165 inches. Allowing one turn per layer and 0.020 inches clearance at the edges allows a maximum trace width of 0.125 inches. Using 100 circular mils(c.m.)/A as a guideline for current density, and from EQ. 10, 707c.m. are required for each of the secondary windings (a circular mil is the area of a circle 0.001 inches in diameter). Converting c.m. to square mils yields 555mils2 (0.785 sq. mils/c.m.). Dividing by the trace width results in a copper thickness of 4.44mils (0.112mm). Using 1.3mils/oz. of copper requires a copper weight of 3.4oz. For reasons of cost, 3oz. copper was selected. The primary windings have an RMS current of approximately 5 A (IOUT x NS/NP at ~ 100% duty cycle). The primary is configured as 2 layers, 2 turns per layer to minimize the winding stack height. Allowing 0.020 inches edge clearance and 0.010 inches between turns yields a trace width of 0.0575 inches. Ignoring the terminal and lead-in resistance, and using EQ. 11, the inner trace has a resistance of 4.25m, and the outer trace has a resistance of 5.52m. The resistance of the primary then is 19.5m at 20°C. The total DC power loss for the primary at 20°C is 489mW. Improved efficiency and thermal performance could be achieved by selecting heavier copper weight for the windings. Evaluation in the application will determine its need. The order and geometry of the windings affects the AC resistance, winding capacitance, and leakage inductance of the finished transformer. To mitigate these effects, interleaving the windings is necessary. The primary winding is sandwiched between the two secondary windings. The winding layout appears below. One layer of each secondary winding also contains the synchronous rectifier winding. For this layer the secondary trace width is reduced by 0.025 inches to 0.100 inches(0.015 inches for the SR winding trace width and 0.010 inches spacing between the SR winding and the secondary winding). The choice of copper weight may be validated by calculating the DC copper losses of the secondary winding. Ignoring the terminal and lead-in resistance, the resistance of each layer of the secondary may be approximated using EQ. 11. 2 R = ----------------------- r 2 t  ln  -----  r 1  FIGURE 7A. TOP LAYER: 1 TURN SECONDARY AND SR WINDINGS (EQ. 11) where R = Winding resistance  = Resistivity of copper = 669e-9-inches at 20°C t = Thickness of the copper (3 oz.) = 3.9e-3 inches r2 = Outside radius of the copper trace = 0.324 or 0.299 inches r1 = Inside radius of the copper trace = 0.199 inches The winding without the SR winding on the same layer has a DC resistance of 2.21m. The winding that shares the layer with the SR winding has a DC resistance of 2.65m. With the secondary configured as a 4 turn center tapped winding (2 turns each side of the tap), the total DC power loss for the secondary at 20°C is 486mW. FN9147 Rev.8.00 September 22, 2005 FIGURE 7B. INT. LAYER 1: 1 TURN SECONDARY WINDING Page 10 of 18 ISL6744 0.689 0.358 0.807 0.639 0.403 0.169 0.000 FIGURE 7C. INT. LAYER 2: 2 TURNS PRIMARY WINDING 0.000 0.184 0.479 0.774 1.054 FIGURE 7G. PWB DIMENSIONS MOSFET Selection The criteria for selection of the primary side half-bridge FETs and the secondary side synchronous rectifier FETs is largely based on the current and voltage rating of the device. However, the FET drain-source capacitance and gate charge cannot be ignored. FIGURE 7D. INT. LAYER 3: 2 TURNS PRIMARY WINDING FIGURE 7E. INT. LAYER 4: 1 TURN SECONDARY WINDING The zero voltage switch (ZVS) transition timing is dependent on the transformer’s leakage inductance and the capacitance at the node between the upper FET source and the lower FET drain. The node capacitance is comprised of the drain-source capacitance of the FETs and the transformer parasitic capacitance. The leakage inductance and capacitance form an LC resonant tank circuit which determines the duration of the transition. The amount of energy stored in the LC tank circuit determines the transition voltage amplitude. If the leakage inductance energy is too low, ZVS operation is not possible and near or partial ZVS operation occurs. As the leakage energy increases, the voltage amplitude increases until it is clamped by the FET body diode to ground or VIN, depending on which FET conducts. When the leakage energy exceeds the minimum required for ZVS operation, the voltage is clamped until the energy is transferred. This behavior increases the time window for ZVS operation. This behavior is not without consequences, however. The transition time and the period of time during which the voltage is clamped reduces the effective duty cycle. The gate charge affects the switching speed of the FETs. Higher gate charge translates into higher drive requirements and/or slower switching speeds. The energy required to drive the gates is dissipated as heat. FIGURE 7F. BOTTOM LAYER: 1 TURN SECONDARY AND SR WINDINGS FN9147 Rev.8.00 September 22, 2005 The maximum input voltage, VIN, plus transient voltage, determines the voltage rating required. With a maximum input voltage of 53V for this application, and if we allow a 10% adder for transients, a voltage rating of 60V or higher will suffice. Page 11 of 18 ISL6744 The RMS current through each primary side FET can be determined from EQ. 10, substituting 5A of primary current for IOUT (assuming 100% duty cycle). The result is 3.5A RMS. Fairchild FDS3672 FETs, rated at 100V and 7.5A (rDS(ON) = 22m), were selected for the half-bridge switches. Once the estimated transition time is determined, it must be verified directly in the application. The transformer leakage inductance was measured at 125nH and the combined capacitance was estimated at 2000pF. Calculations indicate a transition period of ~25ns. Verification of the performance yielded a value of TD closer to 45ns. The synchronous rectifier FETs must withstand approximately one half of the input voltage assuming no switching transients are present. This suggests that a device capable of withstanding at least 30V is required. Empirical testing in the circuit revealed switching transients of 20V were present across the device indicating a rating of at least 60V is required. The remainder of the switching half-period is the charge time, TC, and can be found from The RMS current rating of 7.07A for each SR FET requires a low rDS(ON) to minimize conduction losses, which is difficult to find in a 60V device. It was decided to use two devices in parallel to simplify the thermal design. Two Fairchild FDS5670 devices are used in parallel for a total of four SR FETs. The FDS5670 is rated at 60V and 10A (rDS(ON) = 14m). Using Figure 3, the capacitor value appropriate to the desired oscillator operating frequency of 470kHz can be selected. A CT value of 100pF, 150pF, or 220pF is appropriate for this frequency. A value of 150pF was selected. Oscillator Component Selection The desired operating frequency of 235kHz for the converter was established in the Design Criteria section. The oscillator frequency operates at twice the frequency of the converter because two clock cycles are required for a complete converter period. During each oscillator cycle the timing capacitor, CT, must be charged and discharged. Determining the required discharge time to achieve zero voltage switching (ZVS) is the critical design goal in selecting the timing components. The discharge time sets the deadtime between the two outputs, and is the same as ZVS transition time. Once the discharge time is determined, the remainder of the period becomes the charge time. The ZVS transition duration is determined by the transformer’s primary leakage inductance, Llk, by the FET Coss, by the transformer’s parasitic winding capacitance, and by any other parasitic elements on the node. The parameters may be determined by measurement, calculation, estimate, or by some combination of these methods.  L lk   2C oss + C xfrmr  t zvs  -------------------------------------------------------------------2 s (EQ. 12) Device output capacitance, Coss, is non-linear with applied voltage. To find the equivalent discrete capacitance, Cfet, a charge model is used. Using a known current source, the time required to charge the MOSFET drain to the desired operating voltage is determined and the equivalent capacitance is calculated. Ichg  t Cfet = -------------------V F FN9147 Rev.8.00 September 22, 2005 (EQ. 13) –9 1 1 T C = -------------------- – T D = ---------------------------------- – 45  10 = 2.08 3 2  F Sw 2  235  10 s (EQ. 14) where FSw is the converter switching frequency. To obtain the proper value for RTD, EQ. 3 is used. Since there is a 10ns propagation delay in the oscillator circuit, it must be included in the calculation. The value of RTD selected is 10k. Output Filter Design The output filter inductor and capacitor selection is simple and straightforward. Under steady state operating conditions the voltage across the inductor is very small due to the large duty cycle. Voltage is applied across the inductor only during the switch transition time, about 45ns in this application. Ignoring the voltage drop across the SR FETs, the voltage across the inductor during the on time with VIN = 48V is V IN  N S   1 – D  V L = V S – V OUT = ------------------------------------------------  250 2N P mV (EQ. 15) where VL is the inductor voltage VS is the voltage across the secondary winding VOUT is the output voltage If we allow a current ramp, I, of 5% of the rated output current, the minimum inductance required is V L  T ON 0.25  2.08 L  ------------------------- = ----------------------------- = 1.04 I 0.5 H (EQ. 16) An inductor value of 1.5H, rated for 18A was selected. With a maximum input voltage of 53V, the maximum output voltage is about 13V. The closest higher voltage rated capacitor is 16V. Under steady state operating conditions the ripple current in the capacitor is small, so it would seem appropriate to have a low ripple current rated capacitor. However, a high rated ripple current capacitor was selected Page 12 of 18 ISL6744 based on the nature of the intended load, multiple buck regulators. To minimize the output impedance of the filter, a SANYO OSCON 16SH150M capacitor in parallel with a 22F ceramic capacitor were selected. Current Limit Threshold The current limit threshold is fixed at 0.6V nominal, which is the reference to the overcurrent protection comparator. The current level that corresponds to the overcurrent threshold must be chosen to allow for the dynamic behavior of an open loop converter. In particular, the low inductor ripple current under steady state operation increases significantly as the duty cycle decreases. reduction of the average current through the inductor. The implication is that the converter can not supply the same output current in current limit that it can supply under steady state conditions. The peak current limit setpoint must take this behavior into consideration. A 5.11 current sense resistor was selected for the rectified secondary of current transformer T2 for the ISL6744Eval 1, corresponding to a peak current limit setpoint of about 11A. Performance The major performance criteria for the converter are efficiency, and to a lesser extent, load regulation. Efficiency, load regulation and line regulation performance are demonstrated in the following Figures. As expected, the output voltage varies considerably with line and load when compared to an equivalent converter with a closed loop feedback. However, for applications where tight regulation is not required, such as those applications that use downstream DC/DC converters, this design approach is viable. 14 13 12 11 100 10 9 8 0.9950 0.9960 0.9970 0.9980 0.9990 1.000 TIME (ms) V (L1:1) I (L1) EFFICIENCY (%) 95 FIGURE 8. STEADY STATE SECONDARY WINDING VOLTAGE AND INDUCTOR CURRENT 90 85 85 75 70 15 1 0 2 3 4 5 6 7 8 9 10 LOAD CURRENT (A) FIGURE 10. EFFICIENCY vs LOAD VIN = 48V 10 12.5 5 0.986 0.988 0.990 0.992 0.994 0.996 0.998 1.000 TIME (ms) V (L1:1) I (L1) FIGURE 9. SECONDARY WINDING VOLTAGE AND INDUCTOR CURRENT DURING CURRENT LIMIT OPERATION Figures 8 and 9 show the behavior of the inductor ripple under steady state and overcurrent conditions. In this example, the peak current limit is set at 11A. The peak current limit causes the duty cycle to decrease resulting in a FN9147 Rev.8.00 September 22, 2005 OUTPUT VOLTAGE (V) 12.25 12 11.75 11.5 11.25 11 0 1 2 3 4 5 6 7 8 9 LOAD CURRENT (A) FIGURE 11. LOAD REGULATION AT VIN = 48V Page 13 of 18 10 ISL6744 13.5 OUTPUT VOLTAGE (V) 13 12.5 12 11.5 11 10.5 42 43 44 45 46 47 48 49 50 51 52 53 INPUT VOLTAGE (V) FIGURE 12. LINE REGULATION AT IOUT = 1A Waveforms FIGURE 14. FET DRAIN-SOURCE VOLTAGE Typical waveforms can be found in the following Figures. Figure 13 shows the output voltage ripple and noise at a 5A. FIGURE 15. FET D-S VOLTAGE NEAR-ZVS TRANSITION FIGURE 13. OUTPUT RIPPLE AND NOISE - 20MHz BW Figures 14 and 15 show the voltage waveforms at the switching node shared by the upper FET source and the lower FET drain. In particular, Figure 15 shows near ZVS operation at 5A of load when the upper FET is turning off and the lower FET is turning on. ZVS operation occurs completely, implying that all the energy stored in the node capacitance has been recovered. Figure 16 shows the switching transition between outputs, OUTA and OUTB during steady state operation. The deadtime duration of 46.9ns is clearly shown. A 2.7V zener is added between the Vdd pins of ISL6700 and ISL6744, in order to ensure that the PWM turns on only after the driver has turned on, thereby ensuring the soft-start function. Figure 17 shows the soft-start operation. FIGURE 16. OUTA - OUTB TRANSITION FN9147 Rev.8.00 September 22, 2005 Page 14 of 18 ISL6744 FIGURE 17. OUTPUT SOFT-START Component List REFERENCE DESIGNATOR VALUE C1 1.0µF Capacitor, 1812, X7R, 100V, 20% C2, C3 3.3µF Capacitor, 1812, X5R, 50V, 20% C4 1.0µF Capacitor, 0805, X5R, 16V, 10% C5 0.1µF Capacitor, 0603, X7R, 16V, 10% C6, C15 4.7µF Capacitor, 0805, X5R, 10V, 20% C7 Open Capacitor, 0603, Open or Optional Discrete Stray Capacitance C8 22µF Capacitor, 1812, X5R, 16V, 20% C9 150µF Capacitor, Radial, Sanyo 16SH150M C10, C11, C12, C13, C14 1000pF Capacitor, 0603, X7R, 50V, 10% C16 150pF Capacitor, 0603, COG, 16V, 5% C18 0.01µF Capacitor, 0603, X7R, 16V, 10% CR1, CR2 DESCRIPTION Diode, Schottky, BAT54S, 30V CR3 Diode, Schottky, BAT54, 30V CR4 Diode, Schottky, SMA, 100V, 2.1A D1 Zener, 10V,Zetex BZX84C10ZXCT-ND D2 Zener, 2.7V, BZX84C2V7 L1 190nH Pulse, P2004T L2 1.5µH Bitech, HM73-301R5 L3 Short Jumper or Optional Discrete Leakage Inductance P1, P2, P3, P4 Q5 QL, QH FN9147 Rev.8.00 September 22, 2005 Keystone, 1514-2 NPN Transistor, ON MJD31C FET, Fairchild FDS3672, 100V Page 15 of 18 ISL6744 Component List REFERENCE DESIGNATOR (Continued) VALUE QR1, QR2, QR3, QR4 DESCRIPTION FET, Fairchild FDS5670, 60V R1 3.3 Resistor, 2512, 1% R2 3.01K Resistor, 2512, 1% R5 5.11 Resistor, 0603, 1% R6 205 Resistor, 0603, 1% R7 75.0K Resistor, 0805, 1% R8, R9 20.0 Resistor, 0805, 1% R10 18 Resistor, 2512, 1% R11 100 Resistor, 0603, 1% R12 10.0K Resistor, 0603, 1% T1 Custom Midcom 31718 T2 Custom Midcom 31719R TP1, TP2, TP4, TP5, TP6 5002 SP1 Keystone Tektronix Scope Jack, 131-4353-00 U1 Intersil ISL6744AU, MSOP8 U4 Intersil ISL6700IB, SOIC FN9147 Rev.8.00 September 22, 2005 Page 16 of 18 ISL6744 Mini Small Outline Plastic Packages (MSOP) N M8.118 (JEDEC MO-187AA) 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE E1 INCHES E -B- INDEX AREA 1 2 0.20 (0.008) A B C TOP VIEW 4X  0.25 (0.010) R1 R GAUGE PLANE SEATING PLANE -CA 4X  A2 A1 b -H- 0.10 (0.004) L1 SEATING PLANE C D 0.20 (0.008) C a CL E1 0.20 (0.008) C D MAX MIN MAX NOTES 0.037 0.043 0.94 1.10 - A1 0.002 0.006 0.05 0.15 - A2 0.030 0.037 0.75 0.95 - b 0.010 0.014 0.25 0.36 9 c 0.004 0.008 0.09 0.20 - D 0.116 0.120 2.95 3.05 3 E1 0.116 0.120 2.95 3.05 4 0.026 BSC -B- 0.65 BSC - E 0.187 0.199 4.75 5.05 - L 0.016 0.028 0.40 0.70 6 0.037 REF N C SIDE VIEW MIN A L1 -A- e SYMBOL e L MILLIMETERS 0.95 REF 8 R 0.003 R1 0  - 8 - 0.07 0.003 - 5o 15o 0o 6o 7 - - 0.07 - - 5o 15o - 0o 6o Rev. 2 01/03 END VIEW NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-187BA. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 3. Dimension “D” does not include mold flash, protrusions or gate burrs and are measured at Datum Plane. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions and are measured at Datum Plane. - H - Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. Formed leads shall be planar with respect to one another within 0.10mm (0.004) at seating Plane. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Datums -A -H- . and - B - to be determined at Datum plane 11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. FN9147 Rev.8.00 September 22, 2005 Page 17 of 18 ISL6744 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N INDEX AREA 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE 0.25(0.010) M H B M INCHES E SYMBOL -B1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e  B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N  NOTES: MILLIMETERS 8 0° 8 8° 0° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 7 8° Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. © Copyright Intersil Americas LLC 2004-2005. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN9147 Rev.8.00 September 22, 2005 Page 18 of 18
ISL6744AUZ-T 价格&库存

很抱歉,暂时无法提供与“ISL6744AUZ-T”相匹配的价格&库存,您可以联系我们找货

免费人工找货