ISL9012IRKJZ

ISL9012 Data Sheet December 10, 2015 Dual LDO with Low Noise, Low IQ, and High PSRR FN9220.4 Features ISL9012 is a high performance dual LDO capable of sourcing 150mA current from Channel 1, and 300mA from Channel 2. The device has a low standby current and high-PSRR and is stable with output capacitance of 1µF to 10µF with ESR of up to 200m. The device integrates a Power-On-Reset (POR) function for the VO2 output. The POR delay for VO2 can be externally programmed by connecting a timing capacitor to the CPOR pin. A reference bypass pin is also provided for connecting a noise-filtering capacitor for low noise and high PSRR applications. • Integrates two high performance LDOs - VO1 - 150mA output - VO2 - 300mA output • Excellent transient response to large current steps • Excellent load regulation: 1% voltage change across full range of load current • High PSRR: 70dB @ 1kHz • Wide input voltage capability: 2.3V to 6.5V • Extremely low quiescent current: 45µA (both LDOs on) • Low dropout voltage: typically 120mV @ 150mA The quiescent current is typically only 45µA with both LDO’s enabled and active. Separate enable pins control each individual LDO output. When both enable pins are low, the device is in shutdown, typically drawing less than 0.1µA. • Low output noise: typically 30µVRMS @ 100µA (1.5V) Several combinations of voltage outputs are standard. Output voltage options for each LDO range from 1.5V to 3.3V. Other output voltage options are available on request. • POR output, with adjustable delay time indicates when the VO2 output is good • Stable with 1 to10µF ceramic capacitors • Separate enable pins for each LDO • Soft-start to limit input current surge during enable • Current limit and overheat protection Pinout • ±1.8% accuracy over all operating conditions ISL9012 (10 LD 3X3 DFN) TOP VIEW • Tiny 10 Ld 3x3mm DFN package • -40°C to +85°C operating temperature range VIN 1 10 VO1 EN1 2 9 VO2 • Pin compatible with Micrel MIC2212 • Pb-free (RoHS compliant) EN2 3 8 POR CBYP 4 7 NC Applications CPOR 5 6 GND • PDAs, Cell Phones and Smart Phones • Portable Instruments, MP3 Players • Handheld Devices including Medical Handhelds 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or1-888-468-3774 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright © Intersil Americas LLC 2005, 2006. 2008, 2015. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL9012 Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING VO1 VOLTAGE (V) VO2 VOLTAGE (V) TEMP RANGE (°C) PACKAGE (Pb-free) PKG. DWG. # ISL9012IRNNZ DCTA 3.3 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRNJZ (No longer available, recommended replacement: ISL9000AIRNJZ) DAPA 3.3 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRNFZ (No longer available, recommended replacement: ISL9000AIRNFZ) DARA 3.3 2.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRMNZ DCYA 3.0 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRMMZ (No longer available, recommended replacement: ISL9000AIRMGZ-T) DAAK 3.0 3.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRMGZ DCBC 3.0 2.7 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRJNZ DCBD 2.8 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRJMZ (No longer available, recommended replacement: ISL9000AIRJBZ-T) DAAH 2.8 3.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRJRZ (No longer available, recommended replacement: ISL9000AIRJNZ-T) DAAG 2.8 2.6 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRJCZ (No longer available, recommended replacement: ISL9000AIRJBZ-T) DAAF 2.8 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRFDZ DCBK 2.5 2.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRFCZ DCBL 2.5 2.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRCJZ DCBN 1.8 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9012IRCCZ DCBP 1.8 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C NOTES: 1. Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. For other output voltages, contact Intersil Marketing. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN9220.4 December 10, 2015 ISL9012 Absolute Maximum Ratings Thermal Information Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.1V VO1, VO2 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V Thermal Resistance (Notes 4, 5) Recommended Operating Conditions Ambient Temperature Range (TA) . . . . . . . . . . . . . . .-40°C to +85°C Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 6.5V JA (°C/W) JC (°C/W) 3x3 DFN Package . . . . . . . . . . . . . . . . 50 10 Junction Temperature Range . . . . . . . . . . . . . . . . .-40°C to +125°C Operating Temperature Range . . . . . . . . . . . . . . . . .-40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 5. JC, “case temperature” location is at the center of the exposed metal pad on the package underside. See Tech Brief TB379. Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF; CBYP = 0.01µF; CPOR = 0.01µF PARAMETER SYMBOL TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS DC CHARACTERISTICS Supply Voltage 2.3 VIN Ground Current 6.5 V Quiescent condition: IO1 = 0µA; IO2 = 0µA IDD1 One LDO active 25 40 µA IDD2 Both LDO active 45 60 µA Shutdown Current IDDS @+25°C 0.1 1.0 µA UVLO Threshold VUV+ 1.9 2.1 2.3 V 1.6 1.8 VUVRegulation Voltage Accuracy Variation from nominal voltage output, VIN = VO + 0.5 to 5.5V, TJ = -40°C to +125°C -1.8 Line Regulation VIN = (VOUT + 1.0V relative to highest output voltage) to 5.5V -0.2 Load Regulation IOUT = 100µA to 150mA (VO1 and VO2) 2.0 V +1.8 % 0 0.2 %/V 0.1 0.7 % IOUT = 100µA to 300mA (VO2) Maximum Output Current IMAX Internal Current Limit Thermal Shutdown Temperature % 150 mA VO2: Continuous 300 mA ILIM Dropout Voltage (Note 7) 1.0 VO1: Continuous 350 475 600 mA VDO1 IO = 150mA; VO 2.1V (VO1) 125 200 mV VDO2 IO = 300mA; VO < 2.5V (VO2) 300 500 mV VDO3 IO = 300mA; 2.5V  VO  2.8V (VO2) 250 400 mV VDO4 IO = 300mA; VO > 2.8V (VO2) 200 325 mV TSD+ 145 °C TSD- 110 °C @ 1kHz 70 dB @ 10kHz 55 dB @ 100kHz 40 dB AC CHARACTERISTICS Ripple Rejection IO = 10mA, VIN = 2.8V(min), VO = 1.8V, CBYP = 0.1µF 3 FN9220.4 December 10, 2015 ISL9012 Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF; CBYP = 0.01µF; CPOR = 0.01µF (Continued) PARAMETER SYMBOL Output Noise Voltage MIN (Note 8) TEST CONDITIONS TYP IO = 100µA, VO = 1.5V, TA = +25°C, CBYP = 0.1µF BW = 10Hz to 100kHz (Note 6) 30 MAX (Note 8) UNITS µVrms DEVICE START-UP CHARACTERISTICS Device Enable TIme tEN Time from assertion of the ENx pin to when the output voltage reaches 95% of the VO(nom) 250 500 µs LDO Soft-start Ramp Rate tSSR Slope of linear portion of LDO output voltage ramp during startup 30 60 µs/V EN1, EN2 PIN CHARACTERISTICS Input Low Voltage VIL -0.3 0.5 V Input High Voltage VIH 1.4 VIN+0.3 V 0.1 µA Input Leakage Current IIL, IIH Pin Capacitance CPIN Informative 5 pF POR PIN CHARACTERISTICS POR Thresholds VPOR+ As a percentage of nominal output voltage VPORPOR Delay tPLH CPOR = 0.01µF 91 94 97 % 87 90 93 % 100 200 300 ms 25 tPHL POR Pin Output Low Voltage VOL POR Pin Internal Pull-Up Resistance @IOL = 1.0mA RPOR 78 100 µs 0.2 V 180 k NOTES: 6. Limits established by characterization and are not production tested. 7. VOx = 0.98*VOx(NOM); Valid for VOx greater than 1.85V. 8. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. EN2 tEN VPOR+ VPOR- VPOR+ VPOR-