ISL90842WIV1427Z

DATASHEET ISL90842 FN8096 Rev 1.00 January 16, 2006 Quad Digitally Controlled Variable Resistors Low Noise, Low Power I2C Bus, 256 Taps The ISL90842 integrates four digitally controlled potentiometers (DCP) configured as variable resistors on a monolithic CMOS integrated circuit. Pinout ISL90842 (14 LEAD TSSOP) TOP VIEW The digitally controlled potentiometers are implemented with a combination of resistor elements and CMOS switches. The position of the wipers are controlled by the user through the I2C bus interface. Each potentiometer has an associated Wiper Register (WR) that can be directly written to and read by the user. The contents of the WR controls the position of the wiper. The DCPs can be used as two-terminal variable resistors in a wide variety of applications including control, parameter adjustments, and signal processing. RH3 1 14 RW0 RW3 2 13 RH0 SCL 3 12 VCC SDA 4 11 A1 GND 5 10 A0 RW2 6 9 RH1 RH2 7 8 RW1 Features • Four variable resistors in one package • 256 resistor taps - 0.4% resolution • I2C serial interface • Wiper resistance: 70 typical @ 3.3V • Standby current 2kV Human Body Model Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Power rating of each DCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW Wiper current of each DCP . . . . . . . . . . . . . . . . . . . . . . . . . . ±3.0mA CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Analog Specifications SYMBOL RTOTAL RW CH/CL/CW ILkgDCP Over recommended operating conditions unless otherwise stated. PARAMETER RH to RW resistance TEST CONDITIONS MIN MAX UNIT W option, wiper counter = 00h 10 k U option, wiper counter = 00h 50 k RH to RW resistance tolerance Wiper counter = 00h Wiper resistance VCC = 3.3V @ 25°C, wiper current = VCC/RTOTAL -20 70 Potentiometer capacitance (Note 15) Leakage on DCP pins (Note 15) TYP (NOTE 1) +20 % 200  10/10/25 Voltage at pin from GND to VCC 0.1 pF 1 µA -1 1 MI (Note 2) -0.5 0.5 MI (Note 2) RESISTOR MODE (Measurements between RWi and RHi, i = 0, 1, 2 or 3) RINL (Note 5) Integral non-linearity RDNL (Note 4) Differential non-linearity Roffset (Note 3) Offset DCP register set between 20 hex and FF hex; monotonic over all tap positions U option 0 1 7 MI (Note 2) W option 0 0.5 2 MI (Note 2) -2 2 MI (Note 2) RMATCH (Note 6) DCP to DCP matching Any two DCPs at the same tap position with the same terminal voltages TCR (Note 7) Resistance temperature coefficient DCP register set between 20 hex and FF hex ±45 ppm/°C Operating Specifications Over the recommended operating conditions unless otherwise specified. SYMBOL ICC1 ISB ILkgDig PARAMETER TEST CONDITIONS MIN = 400kHz; SDA = Open; (for I2C, active, TYP (NOTE 1) MAX UNIT VCC supply current (volatile write/ read) fSCL read and write states) 1 mA VCC current (standby) VCC = +5.5V, I2C interface in standby state 5 µA VCC = +3.6V, I2C interface in standby state 2 µA 10 µA Leakage current, at pins A0, A1, SDA, Voltage at pin from GND to VCC and SCL FN8096 Rev 1.00 January 16, 2006 -10 Page 3 of 10 ISL90842 Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) SYMBOL tDCP (Note 8) PARAMETER DCP wiper response time TEST CONDITIONS MIN SCL falling edge of last bit of DCP data byte to wiper change TYP (NOTE 1) MAX UNIT 1 µs SERIAL INTERFACE SPECS VIL A1, A0, SDA, and SCL input buffer LOW voltage -0.3 0.3*VCC V VIH A1, A0, SDA, and SCL input buffer HIGH voltage 0.7*VCC VCC+0.3 V Hysteresis (Note 8) SDA and SCL input buffer hysteresis VOL (Note 8) SDA output buffer LOW voltage, sinking 4mA Cpin (Note 8) fSCL V 0.05* VCC 0 0.4 V A1, A0, SDA, and SCL pin capacitance 10 pF SCL frequency 400 kHz tIN (Note 8) Pulse width suppression time at SDA and SCL inputs Any pulse narrower than the max spec is suppressed 50 ns tAA (Note 8) SCL falling edge to SDA output data valid SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window 900 ns tBUF (Note 8) Time the bus must be free before the start of a new transmission SDA crossing 70% of VCC during a STOP condition, to SDA crossing 70% of VCC during the following START condition 1300 ns tLOW Clock LOW time Measured at the 30% of VCC crossing 1300 ns tHIGH Clock HIGH time Measured at the 70% of VCC crossing 600 ns tSU:STA START condition setup time SCL rising edge to SDA falling edge; both crossing 70% of VCC 600 ns tHD:STA START condition hold time From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC 600 ns tSU:DAT Input data setup time From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC 100 ns tHD:DAT Input data hold time From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window 0 ns tSU:STO STOP condition hold time From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC 600 ns tHD:STO STOP condition hold time for read, or volatile only write From SDA rising edge to SCL falling edge. Both crossing 70% of VCC 600 ns tDH (Note 8) Output data hold time From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window 0 ns tR (Note 8) SDA and SCL rise time From 30% to 70% of VCC 20 + 0.1 * Cb 250 ns tF (Note 8) SDA and SCL fall time From 70% to 30% of VCC 20 + 0.1 * Cb 250 ns Total on-chip and off-chip 10 400 pF Cb (Note 8) Capacitive loading of SDA or SCL Rpu (Note 8) SDA and SCL bus pull-up resistor off- Maximum is determined by tR and tF chip For Cb = 400pF, max is about 2~2.5k For Cb = 40pF, max is about 15~20k FN8096 Rev 1.00 January 16, 2006 1 k Page 4 of 10 ISL90842 Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN TYP (NOTE 1) MAX UNIT tSU:A A1 and A0 setup time Before START condition 600 ns tHD:A A1 and A0 hold time After STOP condition 600 ns SDA vs SCL Timing tHIGH tF SCL tLOW tR tSU:DAT tSU:STA tHD:DAT tHD:STA SDA (INPUT TIMING) tSU:STO tAA tDH tBUF SDA (OUTPUT TIMING) A0 and A1 Pin Timing STOP START SCL CLK 1 SDA IN tSU:A tHD:A A0, A1 NOTES: 1. Typical values are for TA = 25°C and 3.3V supply voltage. 2. MI = |R255 – R0| / 255. R255 and R0 are the measured resistances for the DCP register set to FF hex and 00 hex, respectively. 3. Roffset = R255 / MI, when measuring between RW and RH. 4. RDNL = (Ri – Ri-1) / MI, for i = 32 to 255. 5. RINL = [Ri – (MI • i) – R0] / MI, for i = 32 to 255. 6. RMATCH = (Ri,x – Ri,y) / MI, for i = 0 to 255, x = 0 to 3 and y = 0 to 3. 6  Max  Ri  – Min  Ri   10 7. TC R = ----------------------------------------------------------------  ----------------- for i = 32 to 255, T = -40°C to 85°C. Max ( ) is the maximum value of the resistance and Min ( ) is the  Max  Ri  + Min  Ri    2 125°C minimum value of the resistance over the temperature range. 8. This parameter is not 100% tested. FN8096 Rev 1.00 January 16, 2006 Page 5 of 10 ISL90842 Typical Performance Curves 160 1.8 VCC=2.7, T=+85°C 1.4 120 VCC=2.7, T=-40°C 100 80 60 40 1.2 1 -40°C 0.8 +85°C 0.6 0.4 VCC=5.5, T=-40°C VCC=5.5, T=+85°C VCC=5.5, T=+25°C 20 0 1.6 STANDBY ICC (µA) WIPER RESISTANCE () 140 VCC=2.7, T=+25°C 0 50 100 150 200 0.2 0 2.7 250 +25°C 3.2 3.7 4.2 TAP POSITION (DECIMAL) FIGURE 1. WIPER RESISTANCE vs TAP POSITION [I(RW) = VCC / RTOTAL] FOR 50k (U) 0.5 VCC=5.5, T=+25°C VCC=2.7, T=+25°C VCC=2.7, T=+25°C 0.3 VCC=5.5, T=-40°C 0.1 INL (LSB) DNL (LSB) 0.2 0 VCC=5.5, T=+85°C -0.2 VCC=2.7, T=-40°C 82 132 182 VCC=5.5, T=+85°C 0.1 VCC=2.7, T=+85°C -0.1 -0.3 VCC=2.7, T=+85°C VCC=5.5, T=-40°C -0.3 32 -0.5 32 232 82 1 25 5.5V TC (ppm/°C) END TO END RTOTAL CHANGE (%) 35 0 182 232 FIGURE 4. INL vs TAP POSITION FOR 50k (U) 1.5 2.7V 132 TAP POSITION (DECIMAL) FIGURE 3. DNL vs TAP POSITION FOR 50k (U) 0.5 VCC=2.7, T=-40°C VCC=5.5, T=+25°C TAP POSITION (DECIMAL) -0.5 -1 -1.5 -40 5.2 FIGURE 2. STANDBY ICC vs Vcc 0.3 -0.1 4.7 VCC (V) 15 5 -5 -15 -20 0 20 40 60 TEMPERATURE (°C) FIGURE 5. END TO END RTOTAL % CHANGE vs TEMPERATURE FN8096 Rev 1.00 January 16, 2006 80 -25 32 82 132 182 232 TAP POSITION (DECIMAL) FIGURE 6. TC IN ppm Page 6 of 10 ISL90842 Typical Performance Curves (Continued) SCL INPUT SIGNAL AT WIPER (WIPER UNLOADED MOVEMENT FROM ffh TO 00h) OUTPUT TAP POSITION = MID POINT RTOTAL=9.4K FIGURE 7. FREQUENCY RESPONSE (2.2MHz) FIGURE 8. LARGE SIGNAL SETTLING TIME Principles of Operation I2C Serial Interface The ISL90842 is an integrated circuit incorporating four DCPs with their associated registers, and an I2C serial interface providing direct communication between a host and the DCPs. The ISL90842 supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter and the receiving device as the receiver. The device controlling the transfer is a master and the device being controlled is the slave. The master always initiates data transfers and provides the clock for both transmit and receive operations. Therefore, the ISL90842 operates as a slave device in all applications. DCP Description Each DCP is implemented with a combination of resistor elements and CMOS switches. The physical ends of each DCP are equivalent to the fixed terminals of a mechanical potentiometer. The RW pin of each DCP is connected to intermediate nodes, and is equivalent to the wiper terminal of a mechanical potentiometer. The position of the wiper terminal within the DCP is controlled by an 8-bit volatile Wiper Register (WR). Each DCP has its own WR. When the WR of a DCP contains all zeroes (WR: 00h), its wiper terminal (RW) is closest to its RL terminal. When the WR of a DCP contains all ones (WR: FFh), its wiper terminal (RW) is furthest from the RH terminal. As the value of the WR increases from all zeroes (00h) to all ones (255 decimal), the wiper moves monotonically from the position furthest from RH to a position closer to RH. At the same time, the resistance between RH and RW decreases monotonically. Note that the RL terminals for all four pots are not connected (left floating). While the ISL90842 is being powered up, all four WRs are reset to 80h (128 decimal), which locates RW roughly at a position which yields a rheostat setting that is about 1/2 of RTOTAL. The WRs can be read or written directly using the I2C serial interface as described in the following sections. The I2C interface Address Byte has to be set to 00h, 01h, 02h, and 03h to access the WR of DCP0, DCP1, DCP2, and DCP3, respectively. receiver pulls the SDA line LOW to acknowledge the FN8096 Rev 1.00 January 16, 2006 All communication over the I2C interface is conducted by sending the MSB of each byte of data first. Protocol Conventions Data states on the SDA line must change only during SCL LOW periods. SDA state changes during SCL HIGH are reserved for indicating START and STOP conditions (See Figure 9). On power-up of the ISL90842 the SDA pin is in the input mode. All I2C interface operations must begin with a START condition, which is a HIGH to LOW transition of SDA while SCL is HIGH. The ISL90842 continuously monitors the SDA and SCL lines for the START condition and does not respond to any command until this condition is met (See Figure 9). A START condition is ignored during the power-up of the device. All I2C interface operations must be terminated by a STOP condition, which is a LOW to HIGH transition of SDA while SCL is HIGH (See Figure 9). A STOP condition at the end of a read operation, or at the end of a write operation places the device in its standby mode. An ACK, Acknowledge, is a software convention used to indicate a successful data transfer. The transmitting device, either master or slave, releases the SDA bus after transmitting eight bits. During the ninth clock cycle, the reception of the eight bits of data (See Figure 10). Page 7 of 10 ISL90842 The ISL90842 responds with an ACK after recognition of a START condition followed by a valid Identification Byte, and once again after successful receipt of an Address Byte. The ISL90842 also responds with an ACK after receiving a Data Byte of a write operation. The master must respond with an ACK after receiving a Data Byte of a read operation “1” for a Read operation, and “0” for a Write operation (See Table 1). TABLE 1. IDENTIFICATION BYTE FORMAT Logic values at pins A1, and A0 respectively 0 A valid Identification Byte contains 01010 as the five MSBs, and the following two bits matching the logic values present at pins A1 and A0. The LSB is the Read/Write bit. Its value is 1 0 1 0 A1 (MSB) A0 R/W (LSB) SCL SDA START DATA STABLE DATA CHANGE DATA STABLE STOP FIGURE 9. VALID DATA CHANGES, START, AND STOP CONDITIONS SCL FROM MASTER 1 8 9 SDA OUTPUT FROM TRANSMITTER HIGH IMPEDANCE HIGH IMPEDANCE SDA OUTPUT FROM RECEIVER START ACK FIGURE 10. ACKNOWLEDGE RESPONSE FROM RECEIVER WRITE SIGNALS FROM THE MASTER SIGNAL AT SDA SIGNALS FROM THE ISL90842 S T A R T IDENTIFICATION BYTE ADDRESS BYTE 0 1 0 1 0 A1 A0 0 0 0 0 0 0 0 A C K S T O P DATA BYTE A C K A C K FIGURE 11. BYTE WRITE SEQUENCE FN8096 Rev 1.00 January 16, 2006 Page 8 of 10 ISL90842 SIGNALS FROM THE MASTER S T A R T SIGNAL AT SDA IDENTIFICATION BYTE WITH R/W=0 ADDRESS BYTE 0 1 0 1 0 A1A0 0 A C K S T O P A C K 0 1 0 1 0 A1A0 1 0 0 0 0 0 0 A C K SIGNALS FROM THE SLAVE S T A IDENTIFICATION R BYTE WITH T R/W=1 A C K A C K FIRST READ DATA BYTE LAST READ DATA BYTE FIGURE 12. READ SEQUENCE Write Operation A Write operation requires a START condition, followed by a valid Identification Byte, a valid Address Byte, a Data Byte, and a STOP condition. After each of the three bytes, the ISL90842 responds with an ACK. At this time, the device enters its standby state (See Figure 11). The Data Bytes are from the registers indicated by an internal pointer. This pointer initial value is determined by the Address Byte in the Read operation instruction, and increments by one during transmission of each Data Byte. After reaching the memory location 03h the pointer “rolls over” to 00h, and the device continues to output data for each ACK received. Read Operation A Read operation consist of a three byte instruction followed by one or more Data Bytes (See Figure 12). The master initiates the operation issuing the following sequence: a START, the Identification byte with the R/W bit set to “0”, an Address Byte, a second START, and a second Identification byte with the R/W bit set to “1”. After each of the three bytes, the ISL90842 responds with an ACK. Then the ISL90842 transmits Data Bytes as long as the master responds with an ACK during the SCL cycle following the eighth bit of each byte. The master terminates the read operation (issuing a STOP condition) following the last bit of the last Data Byte (See Figure 12). © Copyright Intersil Americas LLC 2005-2006. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN8096 Rev 1.00 January 16, 2006 Page 9 of 10 ISL90842 Packaging Information 14-Lead Plastic, TSSOP, Package Code V14 .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .193 (4.9) .200 (5.1) .041 (1.05) .0075 (.19) .0118 (.30) .002 (.05) .006 (.15) .010 (.25) Gage Plane 0° - 8° .019 (.50) .029 (.75) Seating Plane Detail A (20X) .031 (.80) .041 (1.05) See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) FN8096 Rev 1.00 January 16, 2006 Page 10 of 10