DATASHEET
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
Description
Features
The MK1574-01A/B are Phase-Locked Loop (PLL) based
clock synthesizers, which accept an 8 kHz clock input as a
reference, and generate many popular communications
frequencies. All outputs are frequency locked together and
to the input. This allows for the generation of locked clocks
to the 8 kHz backplane clock, simplifying clock generation
and distribution in communications systems.
•
•
•
•
Packaged in 16-pin SOIC
Accepts 8 kHz input clock
Output clock rates include T1, E1, T2, E2
Available in commercial (0º to + 70ºC) or industrial (-40 to
+85ºC) temperature ranges
• For jitter attenuation, use the MK2049
1) MK1574-01A — 5 V operation
2) MK1574-01B — 3.3 V operation
IDT manufactures the largest variety of clock generators
and buffers, and can customize this device for a variety of
frequencies.
Block Diagram
VDD
GND
2
2
CLK1
FS0-3
8 kHz
input
clock
4
Input
Buffer
CAP1
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
CLK2
PLL Clock
Synthesis
and Control
Circuitry
CLK3
8 kHz
(recovered)
CAP2
1
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Pin Assignment
ICLK
1
16
FS3
VDD
2
15
NC
VDD
3
14
FS2
CAP1
4
13
FS1
GND
5
12
CLK3
CAP2
6
11
CLK2
GND
7
10
CLK1
FS0
8
9
8KOUT
Output Clocks Decoding Table
Decode
Address
ICLK
Multiplier
CLK1
CLK2
CLK3
FS3:0
(Hex)
pin1
On-chip
pin 10
pin 11
pin 12
0000
0
Reserved
Reserved
Reserved
Reserved
Reserved
0001
1
Reserved
Reserved
Reserved
Reserved
Reserved
0010
2
Reserved
Reserved
Reserved
Reserved
Reserved
0011
3
Reserved
Reserved
Reserved
Reserved
Reserved
0100
4
8.00 kHz
2940
23.52
11.76
5.88
0101
5
8.00 kHz
1960
15.68
7.84
3.92
0110
6
8.00 kHz
2760
22.08
11.04
5.52
0111
7
8.00 kHz
2640
21.12
10.56
5.28
1000
8
8.00 kHz
1920
15.36
7.68
3.84
1001
9
8.00 kHz
6480
51.84
25.92
12.96
1010
A
8.00 kHz
2112
16.896
8.448
4.224
1011
B
8.00 kHz
1578
12.624
6.312
3.156
1100
C
8.00 kHz
8192
65.536
32.768
16.384
1101
D
8.00 kHz
6176
49.408
24.704
12.352
1110
E
8.00 kHz
1024
8.192
4.096
2.048
1111
F
8.00 kHz
772
60176
3.088
1.544
0 = connect directly to ground, 1 = connect directly to VDD.
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
2
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1
ICLK
Input
Clock input. Connect to an 8 kHz clock input.
2
VDD
Power
Connect to 3.3 V for 1574-01B, Connect to 5 V for 1574-01A.
3
VDD
Power
Connect to 3.3 V for 1574-01B, Connect to 5 V for 1574-01A.
4
CAP1
Input
Connect to a ceramic capacitor and a resistor in series between this pin and
CAP2. Refer to the section “Loop Bandwidth and Loop Filter Component
Selection”.
5
GND
Power
Connect to ground.
6
CAP2
Power
Connect to a ceramic capacitor and a resistor in series between this pin and
CAP1. Refer to the section “Loop Bandwidth and Loop Filter Component
Selection”.
7
GND
Power
Connect to ground.
8
FS0
Input
Frequency select 0. Determines CLK outputs per table above.
9
8KOUT
10
CLK1
Output Clock 1 determined by status of FS3:0 per table above.
11
CLK2
Output Clock 2 determined by status of FS3:0 per table above.
12
CLK3
Output Clock 3 determined by status of FS3:0 per table above.
13
FS1
Input
Frequency select 1. Determines CLK outputs per table above.
14
FS2
Input
Frequency select 2. Determines CLK outputs per table above.
15
NC
—
16
FS3
Input
Output Recovered 8 kHz output clock. Can be low jitter, better duty cycle than clock
input.
No connect. Do not connect anything to this pin.
Frequency select 3. Determines CLK outputs per table above.
External Components
The MK1574-01A/B requires a minimum number of external components for proper operation. An RC network (see
the section “Loop Bandwidth and Loop Filter Component Selection”) should be connected between CAP1 and
CAP2 as close tot he device as possible. Decoupling capacitors of 0.01µF should be connected between VDD and
GND on pins 2, 3, 5 and 7, as close to the device as possible. A series termination resistor of 33Ω may be used
close to each clock output pin to reduce reflections.
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
3
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK1574-01A/B. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at
these or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
Item
Rating
Supply Voltage, VDD (referenced to GND)
-0.5 V to 7 V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature (commercial)
0 to +70° C
Ambient Operating Temperature (industrial)
-40 to +85° C
Storage Temperature
-65 to +150° C
Junction Temperature
150° C
Soldering Temperature
260° C
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature (commercial)
Ambient Operating Temperature (industrial)
Power Supply Voltage (measured in respect to GND)
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
4
Typ.
Max.
Units
0
+70
°C
-40
+85
°C
+3.13
+5.5
V
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
DC Electrical Characteristics
MK1574-01A
VDD = 5 V, Ambient temperature 0 to +70° C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Units
5.5
V
Operating Voltage
VDD
4.5
Input High Voltage
VIH
2
Input Low Voltage
VIL
Output High Voltage
VOH
IOH = -4 mA
VDD-0.4
V
Output High Voltage
VOH
IOH = -25 mA
2.4
V
Output Low Voltage
VOL
IOL = 25 mA
Operating Supply
Current
IDD
No Load
Short Circuit Current
IOS
Each output
Input Capacitance
CIN
V
0.8
V
0.4
V
15
mA
±100
mA
7
pF
MK1574-01B
VDD = 3.3 V, Ambient temperature 0 to +70° C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Units
3.6
V
Operating Voltage
VDD
3.0
Input High Voltage
VIH
2
Input Low Voltage
VIL
Output High Voltage
VOH
IOH = -4 mA
VDD-0.4
V
Output High Voltage
VOH
IOH = -25 mA
2.4
V
Output Low Voltage
VOL
IOL = 25 mA
Operating Supply
Current
IDD
No Load
Short Circuit Current
IOS
Each output
Input Capacitance
CIN
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
V
0.8
0.4
5
V
V
13
mA
±100
mA
7
pF
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
AC Electrical Characteristics
MK1574-01A
VDD = 5 V, Ambient Temperature 0 to +70° C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
Typ.
Max. Units
Input Frequency
fIN
8.000
Output Clock Rise Time
tOR
0.8 to 2.0 V
1.5
ns
Output Clock Fall Time
tOF
2.0 to 0.8 V
1.5
ns
Output Clock Duty Cycle,
High time
tDC
At VDD/2
60
%
40
Absolute Clock Period
Jitter
kHz
49 to 51
1
Actual Mean Frequency
Error Versus Target (note
1)
Any clock selection
ns
0
0
ppm
MK1574-01B
VDD = 3.3 V, Ambient Temperature 0 to +70° C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
Typ.
Max. Units
Input Frequency
fIN
8.000
Output Clock Rise Time
tOR
0.8 to 2.0 V
1.5
ns
Output Clock Fall Time
tOF
2.0 to 0.8 V
1.5
ns
Output Clock Duty Cycle,
High time
tDC
At VDD/2
60
%
40
Absolute Clock Period
Jitter
Actual Mean Frequency
Error Versus Target (note
1)
kHz
49 to 51
1
Any clock selection
ns
0
0
ppm
Note 1: All multipliers as shown in the table on page two are exact, and are stored in ROM on the chip.
Thermal Characteristics
Parameter
Thermal Resistance Junction to
Ambient
Thermal Resistance Junction to Case
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
Symbol
Conditions
Min.
Typ.
Max. Units
θJA
Still air
120
° C/W
θJA
1 m/s air flow
115
° C/W
θJA
3 m/s air flow
105
° C/W
58
° C/W
θJC
6
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Loop Bandwidth and Loop Filter Component Selection
The series-connected capacitor and resistor between CAP1 and CAP2 (pins 4 and 6) determine the dynamic
characteristics of the phase-locked loop. The capacitor must have very low leakage, therefore a high quality
ceramic capacitor is recommended. DO NOT use any type of polarized or electrolytic capacitor. The series
connected capacitor and resistor between CAP1 and CAP2 (pins 4 and 6) determine the dynamic characteristics of
the phase-locked loop. The capacitor must have very low leakage, therefore a high quality ceramic capacitor is
recommended. DO NOT use any type of polarized or electrolytic capacitor. Ceramic capacitors should have C0G or
NP0 dielectric. Avoid high-K dielectrics like Z5U and X7R; these and other ceramics which have piezoelectric
properties allow mechanical vibration in the system to increase the output jitter because the mechanical energy is
converted directly to voltage noise on the VCO input.
The values of the RC network determine the bandwidth of the PLL. The values of the loop filter components are
calculated using the constants K1 and K2 from the Loop Filter Constants table (page 7). The loop bandwidth is set
by the capacitor C and the constant K1 using the formula:
BW (Hz) =
K1
Equation 1
C
The loop damping is set by the resistor R, the capacitor C, and the constant K2 using the formula::
R=
ζ * K2
C
Equation 2; ζ (zeta) is the damping factor
For example, to design the loop filter whewn generating 8.192 MHz from 8 kHz:
1. From the Output Clock Decoding table (page 2), the address is E. The Loop Filter Constants table (page 7)
shows the constants K1 = 0.0516 and K2 = 6.2.
2. A good value for the loop bandwidth is 1/20 the input frequency; where 8 kHz/20 = 400 Hz. Using equation 1,
400 =
K1
C
Therefore,
C=
( 0.0516 ) 2
= 16.6 nF (16 nF nearest standard value
400
3. A good value for the damping factor ζ is 0.707. From equation 2,
R=
0.707 * 6.2
16E-9
= 34.7 kΩ (36 kΩ nearest standard value)
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
7
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Loop Filter Constants
This table shows the constants K1 and K2 that are used with the equations on page 6 to calculate the external loop filter
components.Loop Filter Contstants for MK1574-01A
Decode
Address
Loop Filter Constants
FS3:0
(Hex)
K1
K2
0000
0
Reserved
Reserved
0001
1
Reserved
Reserved
0010
2
Reserved
Reserved
0011
3
Reserved
Reserved
0100
4
0.0430
7.4
0101
5
0.0527
6.0
0110
6
0.0444
7.2
0111
7
0.0454
7.0
1000
8
0.0533
6.0
1001
9
0.0410
7.8
1010
A
0.0508
6.3
1011
B
0.0587
5.4
1100
C
0.0365
8.7
1101
D
0.0420
7.6
1110
E
0.0516
6.2
1111
F
0.0594
5.4
PC Board Layout
A proper board layout is critical to the successful use of the MK1574-01A/B. In particular, the CAP1 and CAP2 pins
are very sensitive to noise and leakage (CAP1 at pin 4 is the most sensitive). Traces must be as short as possible
and the capacitor and resistor must be mounted next to the device as shown to the right. The capacitor connected
between pins 3 and 5 is the power supply decoupling capacitor. The high frequency output clocks on may benefit
from a series 33Ω resistor connected close to the pin (not shown).
Clock Multipliers/Accuracies
In the table on page 2 are the actual multipliers stored in the MK1574-01A/B ROM, which yield the exact values
shown for the output clocks.
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
8
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Package Outline and Package Dimensions (16-pin SOIC, 150 Mil. Narrow Body)
Package dimensions are kept current with JEDEC Publication No. 95
16
Millimeters
Symbol
E
A
A1
B
C
D
E
e
H
h
L
α
H
INDEX
AREA
1 2
D
A
Min
Inches
Max
Min
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
9.80
10.00
3.80
4.00
1.27 BASIC
5.80
6.20
0.25
0.50
0.40
1.27
0°
8°
Max
.0532
.0688
.0040
.0098
.013
.020
.0075
.0098
.3859
.3937
.1497
.1574
0.050 BASIC
.2284
.2440
.010
.020
.016
.050
0°
8°
h x 45
A1
C
-Ce
B
SEATING
PLANE
L
.10 (.004)
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
C
9
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Ordering Information
Part / Order Number
Marking
Shipping Packaging
Package
Temperature
MK1574-01ASLF
MK1574-01ASLFTR
MK1574-01ASILF
MK1574-01ASILFTR
MK1574-01BSLF
MK1574-01BSFLTR
MK1574-01BSILF
MK1574-01BSILFTR
157401ASLF
157401ASLF
157401ASILF
157401ASILF
157401BSLF
157401BSLF
157401BSILF
157401BSILF
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
16-pin SOIC
16-pin SOIC
16-pin SOIC
16-pin SOIC
16-pin SOIC
16-pin SOIC
16-pin SOIC
16-pin SOIC
0 to +70° C
0 to +70° C
-40 to +85° C
-40 to +85° C
0 to +70° C
0 to +70° C
-40 to +85° C
-40 to +85° C
“LF”designates the Pb-free configuration and RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for either its use or for the
infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product
is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other
extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or
specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
IDT™ / ICS™ FRAME RATE COMMUNICATIONS PLL
10
MK1574-01A/B
REV D 051310
MK1574-01A/B
FRAME RATE COMMUNICATIONS PLL
CLOCK SYNTHESIZER
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
www.idt.com/go/clockhelp>
Corporate Headquarters
Integrated Device Technology, Inc.
www.idt.com
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device
Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered
trademarks used to identify products or services of their respective owners.
Printed in USA
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.