DATASHEET
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
Description
Features
The MK2049-34A is a VCXO Phased Locked Loop (PLL)
based clock synthesizer that accepts multiple input
frequencies. With an 8 kHz clock input as a reference, the
MK2049-34A generates T1, E1, T3, E3, ISDN, xDSL, and
other communications frequencies. This allows for the
generation of clocks frequency-locked and phase-locked to
an 8 kHz backplane clock, simplifying clock synchronization
in communications systems. The MK2409-34 can also
accept a T1 or E1 input clock and provide the same output
for loop timing. All outputs are frequency locked together
and to the input.
•
•
•
•
•
Packaged in 20-pin SOIC
Available in Pb (lead) free package
3.3 V + 5% operation
Fixed I/O phase relationship on all selections
Meets the TR62411, ETS300 011, and GR-1244
specification for MTIE, Pull-in/Hold-in Range, Phase
Transients, and Jitter Generation for Stratum 3, 4, and 4E
• Accepts multiple inputs: 8 kHz backplane clock, Loop
Timing frequencies, or 10 to 36 MHz
• Locks to 8 kHz + 100 ppm (External mode)
• Buffer Mode allows jitter attenuation of 10 to 36 MHz
This part also has a jitter-attenuated Buffer capability. In this
mode, the MK2049-34A is ideal for filtering jitter from 27
MHz video clocks or other clocks with high jitter.
input and x1/x0.5 or x2/x4 outputs
• Exact internal ratios enable zero ppm error
• Output clock rates include T1, E1, T3, E3, ISDN, xDSL,
IDT can customize these devices for many other different
frequencies.
and the OC3 submultiples
• See the MK2049-01, -02, and -03 for more selections at
5V
• Industrial temperature range
NOTE: EOL for non-green parts to occur on 5/13/10
per PDN U-09-01
Block Diagram
EXTERNAL PULLABLE CRYSTAL
(external loop filter)
INPUT REFERENCE
CLOCK
(TYPICALLY 8KHZ)
VCXO-BASED
PLL
FREQUENCY
MULTIPLYING
PLL
(MASTER CLOCK
GENERATOR)
FREQUENCY SELECT
2
CLOCK OUTPUT / 2
8 KHZ (REGENERATED)
4
IDT™ 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
CLOCK OUTPUT
1
MK2049-34A
REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
Pin Assignment
FS1
X2
1
2
20
19
FS0
RES
X1
VDD
3
4
18
17
CAP2
GND
FCAP
VDD
GND
CLK
CLK/2
8k
5
6
16
15
CAP1
VDD
7
8
9
10
14
13
GND
ICLK
FS3
FS2
12
11
20-pin (300) mil SOIC
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1
FS1
Input
2
X2
XO
Crystal connection. Connect to a MHz crystal as shown in table on page 3.
3
X1
XI
Crystal connection. Connect to a MHz crystal as shown in table on page 3.
4
VDD
Power
5
FCAP
—
6
VDD
Power
Power supply. Connect to +3.3 V.
7
GND
Power
Connect to ground
8
CLK
Output
Clock output determined by status of FS3:0 per tables on page 3.
9
CLK/2
Output
10
8k
Output
Clock output determined by status of FS3:0 per tables page 3. Always 1/2 of
CLK.
Recovered 8 kHz clock output.
11
FS2
Input
Frequency select 2. Determines CLK input/outputs per tables on page 3.
12
FS3
Input
Frequency select 3. Determines CLK input/outputs per tables on page 3.
13
ICLK
Input
Input clock connection. Connect to 8 kHz backplane or MHz clock.
14
GND
Power
Connect to ground.
15
VDD
Power
Power Supply. Connect to +3.3 V.
16
CAP1
17
GND
Loop
Filter
Power
Connect the loop filter ceramic capacitors and resistor between this pin and
CAP2.
Connect to ground.
18
CAP2
Loop
Connect the loop filter ceramic capacitors and resistor between this pin and
19
RES
—
20
FS0
Input
Connect a 10-200kΩ resistor to ground. Contact IDT for recommended value
for your application.
Frequency select 0. Determines CLK input/outputs per table on page 3.
Frequency select 1. Determines CLK input/outputs per table on page 3.
Power supply. Connect to +3.3 V.
Filter capacitor. Connect a 1000 pF ceramic capacitor to ground.
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
2
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
Output Decoding Table - External Mode (MHz)
ICLK
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
FS3
0
0
0
0
0
0
0
0
1
1
1
1
FS2
0
0
0
0
1
1
1
1
0
0
1
1
FS1
0
0
1
1
0
0
1
1
1
1
0
0
FS0
0
1
0
1
0
1
0
1
0
1
0
1
CLK/2
1.544
2.048
22.368
17.184
19.44
16.384
17.664
18.688
7.68
10.752
10.24
38.88
CLK
3.088
4.096
44.736
34.368
38.88
32.768
35.328
37.376
15.36
21.504
20.48
77.76
8k
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
8 kHz
Crystal
Used (MHz)
12.352
12.288
11.184
11.456
9.72
8.192
17.664
9.344
15.36
10.752
10.24
9.72
N
1544
1536
1398
1432
1215
1024
2208
1168
1920
1344
1280
1215
Output Decoding Table - Loop Timing Mode (MHz)
ICLK
FS3
FS2
FS1
FS0
CLK/2
CLK
8k
Crystal
N
1.544
1
0
0
0
1.544
3.088
N/A
12.352
24
2.048
1
0
0
1
2.048
4.096
N/A
12.288
18
Output Decoding Table - Buffer Mode (MHz)
ICLK
FS3
FS2
FS1
FS0
CLK/2
CLK
8k
Crystal
N
19 - 36
1
1
1
0
ICLK/2
ICLK
N/A
ICLK/2
3
10 - 18
1
1
1
1
2*ICLK
4*ICLK
N/A
ICLK
3
0 = connect directly to ground, 1 = connect directly to VDD
Crystal is connected to pins 2 and 3; clock input is applied to pin 13.
Operating Modes
The MK2049-34A has three operating modes: External, Loop Timing, and Buffer. Although each mode uses an input clock
to generate various output clocks, there are important differences in their input and crystal requirements.
External Mode
The MK2049-34 accepts an external 8 kHz clock and will produce a number of common communication clock frequencies.
The 8 kHz input clock does not need to have a 50% duty cycle; a “high” or “on” pulse as narrow as 10 ns is acceptable. In
the MK2049-34, the rising edges of CLK and CLK/2 are both aligned with the rising edge of the 8 kHz ICLK; refer to Figure
1 on page 4 for more details.
Loop Timing Mode
This mode can be used to remove the jitter from standard high-frequency communication clocks. For T1 and E1 inputs, the
CLK/2 output will be the same as the input frequency, with CLK at twice the input frequency.
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
3
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
Buffer Mode
Unlike the other two modes that accept only a single specified input frequency, Buffer Mode will accept a wider range of
input clocks. The input jitter is attenuated and the outputs on CLK and CLK/2 also provide the option of getting x1, x2, x4, or
1/2 of the input frequency. For example, this mode can be used to remove the jitter from a 27 MHz clock, generating
low-jitter 27 MHz and 13.5 MHz outputs.
Input and Output Synchronization
As shown in the tables on page 3, the MK2049-34A offers a Zero Delay feature in all selections. There is an internal
feedback path between ICLK and the output clocks, providing a fixed phase relationship between the input and output, a
requirement in many communication systems.
The rising edge of ICLK will be aligned with the rising edges of CLK and CLK/2 (8 kHz is used in this illustration, but the
same is true for the selections in the Loop Timing and Buffer Modes).
IC L K (8 k H z )
C L K (M H z )
C L K /2 (M H z )
F ig u r e 1 . M K 2 0 4 9 -3 4 In p u t a n d O u tp u t C lo c k W a v e fo r m s
Measuring Zero Delay on the MK2049
The MK2049-34 produces low-jitter output clocks. In addition, this part has a very low bandwidth on the order of a few Hertz.
Since most 8 kHz input clocks will have high jitter, this can make measuring the input-to-output skew (zero delay feature)
very difficult. The MK2049 is designed to reject the input jitter; when the input and output clocks are both displayed on an
oscilloscope, they may appear not to be locked because the scope trigger point is constantly changing with the input jitter.
In fact, the input and output clocks probably are locked and the MK2049 will have zero delay to the average position of the
8 kHz input clock. In order to see this clearly, a low jitter 8 kHz input clock is necessary. Most lab frequency sources are NOT
SUITABLE for this since they have high jitter at low frequencies.
Frequency Locking to the Input
In all modes, the output clocks are frequency-locked to the input. The outputs will remain at the specified output frequency
as long as the combined variation of the input frequency and the crystal does not exceed 100 ppm. For example, if the
crystal can vary ±40 ppm (initial accuracy + temperature + aging), then the input frequency can vary by up to 60 ppm and
still have the output clock remain frequency-locked.
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
4
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
PC Board Layout
A proper board layout is critical to the successful use of the MK2049-34A. In particular, the CAP1 and CAP2 pins are very
sensitive to noise and leakage (CAP2 at pin 18 is the most sensitive). Traces must be as short as possible and the two
capacitors and resistor must be mounted next to the device as shown below. The capacitor shown between pins 15 and 17,
and the one between pins 4 and 7 are the power supply decoupling capacitors. The high frequency output clocks on pins 8
and 9 should have a series termination of 33Ω connected close to the pin. Additional improvements will come from keeping
all components on the same side of the board, minimizing vias through other signal layers, and routing other signals away
from the MK2049. You may also refer to application note MAN05 for additional suggestions on layout of the crystal selection.
The crystal traces should include pads for small capacitors from X1 and X2 to ground. These are used to adjust the stray
capacitance of the board to match the crystal load capacitance. The typical telecom reference frequency is accurate to
much less than 1 ppm, so the MK2049-34A may lock and run properly even if the board capacitance is not adjusted with
these fixed capacitors. However, IDT recommends that the adjustment capacitors be included to minimize the effects of
variation in individual crystals, temperature, and aging. The value of these capacitors (typically 0 - 4 pF) is determined once
for a given board layout, using the procedure found in application note MAN05.
Cutout in ground and power plane.
Route all traces away from this area.
cap
resist
resist
cap
cap
20
19
3
18
4
17
5
16
6
15
7
14
8
9
13
12
V
= connect to VDD
10
11
G
= connect to GND
G
resist
resist
cap
V
1
2
G
cap
G
cap
Optional see text
cap
V
Figure 2. Typical MK2049-34 Layout
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
5
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
External Component Selection
The MK2049-34A requires a minimum number of external components for proper operation. Decoupling capacitors of
0.01µF must be connected between VDD and GND pins close to the chip (especially pins 4 and 7, 15 and 17), and 33Ω
series terminating resistors should be used on clock outputs with traces longer than one inch (assuming 50Ω traces). The
selection of additional external components is described in the following sections.
Loop Filter
Information on how to configure the external loop filter, connected between pins CAP1 and CAP2, can be found on the IDT
web site.
Crystal Operation
The MK2049-34A operates by phase locking the input signal to a VCXO which consists of the recommended pullable VCXO
crystals and the integrated VCXO oscillator circuit on the MK2049-34A. To achieve the best performance and reliability, the
layout guidelines shown on the previous page should be closely followed.
The frequency of oscillation of a quartz crystal is determined by its cut and by the load capacitors connected to it. The
MK2049-34A has variable load capacitors on-chip which “pull” or change the frequency of the crystal. External stray
capacitance must be kept to a minimum to ensure maximum pullability of the crystal. To achieve this, the layout should use
short traces between the MK2049-34A and the crystal.
For the VCXO to operate correctly, a pullable crystal must be used. For more information, including a list of approved
crystals, please refer to application note MAN05.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK2049-34A. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at
these or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
Item
Rating
Supply Voltage, VDD
7V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
-40 to +85° C
Storage Temperature
-65 to +150° C
Junction Temperature
175° C
Soldering Temperature
260° C (10 to 20 seconds max.)
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature
-40
Power Supply Voltage (measured in respect to GND)
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
Typ.
6
+3.15
+3.3
Max.
Units
+85
°C
+3.45
V
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
DC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Units
3.3
3.45
V
Operating Voltage
VDD
3.15
Input High Voltage
VIH
2
Input Low Voltage
VIL
Output High Voltage
(CMOS Level)
VOH
IOH = -4 mA
VDD-0.4
V
Output High Voltage
VOH
IOH = -8 mA
2.4
V
Output Low Voltage
VOL
IOL = 8 mA
Operating Supply Current
IDD
No Load, VDD=3.3 V
Short Circuit Current
IOS
Each Output
Input Capacitance
CIN
FS3:0
V
0.8
0.4
V
V
7
mA
±50
mA
5
pF
AC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C
Parameter
Symbol
Input Frequency
Input Clock Pulse Width
Conditions
Min.
External Mode, Note 1
ICLK
tpi
Typ.
Max. Units
8
kHz
10
Propagation Delay
ICLK to ICLK
Output-Output Skew
CLK to CLK/2
ns
0
6
ns
150
ps
Output Clock Rise Time
tOR
0.8 to 2.0 V
2
ns
Output Fall Time
tOF
2.0 to 0.8 V
2
ns
60
%
0
ppm
Output Clock Duty Cycle, High
Time
at VDD/2, except 8 kHz
Actual mean frequency error
versus target
Any clock selection
40
0
Note 1: For loop timing modes and buffer modes, see tables on page 3 for required input clock frequencies
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
7
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
Package Outline and Package Dimensions (20-pin SOIC, 300 Mil. Wide Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
Inches
20
Symbol
E
A
A1
B
C
D
E
e
H
h
L
α
H
INDEX
AREA
1 2
D
A
Min
Max
-2.65
0.10
-0.33
0.51
0.18
0.32
12.60
13.00
7.40
7.60
1.27 BASIC
10.00
10.65
0.25
0.75
0.40
1.27
0°
8°
Min
Max
-.104
.0040
-.013
.020
.007
.013
.496
.512
.291
.299
0.050 BASIC
.394
.419
.010
.029
.016
.050
0°
8°
h x 45
A1
C
-Ce
B
SEATING
PLANE
L
.10 (.004)
C
Ordering Information
Part / Order Number
Marking
Shipping Packaging
Package
Temperature
MK2049-34SAI*
MK2049-34SAI
Tubes
20-pin SOIC
-40 to +85° C
MK2049-34SAITR*
MK2049-34SAI
Tape and Reel
20-pin SOIC
-40 to +85° C
MK2049-34SAILF
MK2049-34SAILF
Tubes
20-pin SOIC
-40 to +85° C
MK2049-34SAILFTR
MK2049-34SAILF
Tape and Reel
20-pin SOIC
-40 to +85° C
*NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01
Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes
no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No
other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications
such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not
recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT
does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
IDT™ / 3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
8
MK2049-34A REV D 121809
MK2049-34A
3.3 VOLT COMMUNICATIONS CLOCK VCXO PLL
VCXO AND SYNTHESIZER
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
www.idt.com/go/clockhelp
Corporate Headquarters
Integrated Device Technology, Inc.
www.idt.com
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device
Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered
trademarks used to identify products or services of their respective owners.
Printed in USA
