DATASHEET
MK2746-01
USB-DVR CLOCK SOURCE
Description
Features
The MK2746-01 is a low cost, low jitter, high performance
clock synthesizer for USB-DVR based applications. Using
analog Phase Locked Loop (PLL) techniques, the device
accepts a 27 MHz fundamental mode crystal or clock input
to produce multiple output clocks for USB and Video
applications.
• Packaged in 16 pin TSSOP
• Operating voltage of 3.3 V
• Provides three fixed outputs of 27 MHz, 24.576 MHz
(Video), and 24 MHz (USB).
• Advanced, low power, sub-micron CMOS process
• Available in RoHS 5 (green) or RoHS 6 (green and lead
IDT manufacturers the largest variety of DVD, set top box,
and multimedia clock synthesizers for all applications.
free) compliant package
NOTE: EOL for non-green parts to occur on
5/13/10 per PDN U-09-01
Block Diagram
VDD
4
24.576M Video decoder clock..
PLL / Clock
Circuit
24M USB Clock
27 MHz crystal
or clock
X1/ICLK
X2
Clock Buffer/
Crystal
Ocsillator
3
27M Video Clock
4
OE
G ND
External crystal capacitors may be required
IDT™ USB-DVR CLOCK SOURCE
1
MK2746-01
REV D 122109
MK2746-01
USB-DVR CLOCK SOURCE
CLOCK SYNTHESIZER
Pin Assignment
X2
1
16
27M
X1/ICLK
2
15
27M
VDD
3
14
27M
GND
4
13
VDD
24M
5
12
GND
VDD
6
11
GND
OE
7
10
VDD
24.576M
8
9
GND
16 pin (173 mil) TSSOP
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1
X2
Input
Connect to a 27 MHz fundamental mode crystal. Leave open for clock input.
2
X1/ICLK
Input
Connect to a 27 MHz fundamental mode crystal or clock.
3
VDD
Power
Connect to +3.3 V.
4
GND
Power
Connect to ground.
5
24M
Output
24MHz USB clock output . Internal pull-down to low when OE is low.
6
VDD
Power
Connect to +3.3 V.
7
OE
Input
Output enable (OE high enables outputs). Internal pull-up.
8
24.576M
Output
24.576 MHz clock output. Internal pull-down to low when OE is low.
9
GND
Power
Connect to ground.
10
VDD
Power
Connect to +3.3 V.
11
GND
Power
Connect to ground.
12
GND
Power
Connect to ground.
13
VDD
Power
Connect to +3.3 V.
14
27M
Output
27 MHz clock output. Internal pull-down to low when OE is low.
15
27M
Output
27 MHz clock output. Internal pull-down to low when OE is low.
16
27M
Output
27 MHz clock output. Internal pull-down to low when OE is low.
External Component Selection
The MK2746-01 requires a minimum number of external
components for proper operation.
capacitors should be mounted on the component side of the
PCB. Avoid the use of vias in the decoupling circuit.
Decoupling Capacitors
Series Termination Resistor
Decoupling capacitors of 0.01µF should be connected
between VDD and GND as close to the MK2746-01 as
possible. For optimum device performance, the decoupling
When the PCB traces between the clock outputs and the
loads are over 1 inch, series termination should be used. To
series terminate a 50Ω trace (a commonly used trace
IDT™ USB-DVR CLOCK SOURCE
2
MK2746-01
REV D 122109
MK2746-01
USB-DVR CLOCK SOURCE
CLOCK SYNTHESIZER
impedance) place a 33Ω resistor in series with the clock line,
as close to the clock output pin as possible. The nominal
impedance of the clock output is 20Ω.
be kept as short as possible, as should the PCB trace to the
ground via. Distance of the ferrite bead and bulk decoupling
from the device is less critical.
Crystal Tuning Load Capacitors
2) The external crystal should be mounted just next to the
device with short traces. The X1 and X2 traces should not
be routed next to each other with minimum spaces, instead
they should be separated and away from other traces.
For a crystal input, a parallel resonant fundamental mode
crystal should be used. Crystal capacitors must be
connected between each of the pins X1 and X2 to ground.
The value (in pF) of these crystal caps should equal
(CL-6)*2. In this equation CL is equal to the crystal load
capacitance in pF. As an example, for a crystal with an 18pF
load capacitance, each crystal capacitor would be 24pF
[(18-6)*2]=24.
3) To minimize EMI the 33Ω series termination resistor, if
needed, should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers (the ferrite bead and bulk decoupling capacitor can be
mounted on the back). Other signal traces should be routed
away from the MK2746-01-01. This includes signal traces
just underneath the device, or on layers adjacent to the
ground plane layer used by the device.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) The 0.01µF decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK2746-01. These ratings, which are
standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these
or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
Item
Rating
Supply Voltage, VDD
7V
All Inputs and Outputs
-0.5V to VDD+0.5V
Ambient Operating Temperature
0 to +70° C
Storage Temperature
-65 to +150° C
Soldering Temperature
260° C
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
IDT™ USB-DVR CLOCK SOURCE
3
Typ.
Max.
Units
0
+70
°C
+3.0
+3.6
V
MK2746-01
REV D 122109
MK2746-01
USB-DVR CLOCK SOURCE
CLOCK SYNTHESIZER
DC Electrical Characteristics
VDD=3.3V ±10% , Ambient temperature 0 to +70° C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Units
3.6
V
0.8
V
V
V
(VDD/2)+1
V
Operating Voltage
VDD
3.0
Input High Voltage
Input Low Voltage
Input High Voltage
VIH
VIL
VIH
2.0
ICLK
Input Low Voltage
VIL
ICLK
Output High Voltage
VOH
IOH = -20 mA
Output Low Voltage
VOL
IOL = 20 mA
Output High Voltage (CMOS
Level)
VOH
IOH = -4 mA
Operating Supply Current
IDD
No load, OE=1
21
mA
No load, OE=0
15
mA
(VDD/2)-1
VDD/2
VDD/2
2.4
V
0.4
V
VDD-0.4
V
Short Circuit Current
IOS
±50
mA
Input Capacitance
CIN
5
pF
Nominal Output Impedance
ZOUT
20
Ω
On Chip Pull Up Resistor
RPU
510
kΩ
On Chip Pull Down Resistor
RPD
240
kΩ
AC Electrical Characteristics
VDD = 3.3V ±10%, Ambient Temperature 0 to +70° C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
Input Frequency
Typ.
Max. Units
27
MHz
Output Rise Time
tOR
20% to 80% of VDD, Note 1
1.2
1.8
ns
Output Fall Time
tOF
80% to 20% of VDD, Note 1
1.2
1.8
ns
Output Clock Duty Cycle
tD
at VDD/2, Note 1
50
55
%
Maximum Output Jitter,
short term
tJ
All clocks, except REF clocks
Note 1
+75
ps
REF clocks, Note 1
+150
ps
45
Output Enable time
OE high to valid output (PLL
running)
20
ns
Output Disable time
OE low to output disable
20
ns
Note 1: Measured with 15pF load.
IDT™ USB-DVR CLOCK SOURCE
4
MK2746-01
REV D 122109
MK2746-01
USB-DVR CLOCK SOURCE
CLOCK SYNTHESIZER
Package Outline and Package Dimensions (16 pin TSSOP, 4.40 mm Body, 0.65 mm Pitch)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
16
Symbol
E1
A
A1
A2
b
C
D
E
E1
e
L
α
aaa
E
IN D EX
AR EA
1
2
D
A
2
Min
Inches
Max
-1.20
0.05
0.15
0.80
1.05
0.19
0.30
0.09
0.20
4.90
5.1
6.40 BASIC
4.30
4.50
0.65 Basic
0.45
0.75
0°
8°
-0.10
Min
Max
-0.047
0.002
0.006
0.032
0.041
0.007
0.012
0.0035 0.008
0.193
0.201
0.252 BASIC
0.169
0.177
0.0256 Basic
0.018
0.030
0°
8°
-0.004
A
A
1
c
-C e
b
S E A TIN G
P LA N E
L
aaa C
Ordering Information
Part / Order Number
Marking
Shipping Packaging
Package
MK2746-01G*
MK2746-01GT*
MK2746-01GLF
MK2746-01GLFT
MK2746-01G
MK2746-01G
274601GL
274601GL
Tubes
Tape and Reel
Tubes
Tape and Reel
16 pin TSSOP
16 pin TSSOP
16 pin TSSOP
16 pin TSSOP
Temperature
0 to +70°
0 to +70°
0 to +70°
0 to +70°
C
C
C
C
*NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01
Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes
no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No
other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications
such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not
recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT
does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
IDT™ USB-DVR CLOCK SOURCE
5
MK2746-01
REV D 122109
MK2746-01
USB-DVR CLOCK SOURCE
CLOCK SYNTHESIZER
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
www.idt.com/go/clockhelp
Corporate Headquarters
Integrated Device Technology, Inc.
www.idt.com
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device
Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered
trademarks used to identify products or services of their respective owners.
Printed in USA