MK3727DLF

DATASHEET MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO Description Features The MK3727D combines the functions of a VCXO (Voltage Controlled Crystal Oscillator) and PLL (Phase Locked Loop) frequency doubler onto a single chip. Used in conjunction with an external pullable quartz crystal, this monolithic integrated circuit replaces more costly hybrid (canned) VCXO devices. The MK3727D is designed primarily for data and clock recovery applications within end products such as ADSL modems, set-top box receivers, and telecom systems. • 24 to 36 MHz output frequency range (output frequency = 2x crystal frequency) • Uses an inexpensive 12 to 18 MHz external crystal • Ideal for ADSL applications using 17.664 MHz external pullable crystal to generate locked 35.328 MHz clock physical layer clock • Ideal for set-top box applications using 13.5 MHz external pullable crystal to generate lock 27 MHz clock transport video clock The frequency of the on-chip VCXO is adjusted by an external control voltage input into pin VIN. Because VIN is a high impedance input, it can be driven directly from an PWM RC integrator circuit. Frequency output increases with VIN voltage input. The usable range of VIN is 0 to 3 V. • On-chip VCXO with guaranteed pull range of ±115 ppm minimum • VCXO input tuning voltage 0 to 3.3 V • Packaged in 8-pin SOIC (150 mil wide) • Available in Pb-free packaging Block Diagram V IN 12 to 1 8 M H z P ullab le C rystal X1 X2 V o lta g e C o n tro lled C ry sta l O s cilla to r IDT™ / ICS™ LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO PLL F re q u e n c y D o u b ler 1 24 to 36 M H z (2x C rystal F re q ue ncy) MK3727D REV M 030806 MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO VCXO AND SYNTHESIZER Pin Assignment X1 1 8 X2 VDD 2 7 GND VIN 3 6 NC GND 4 5 CLK 8-Pin (150 mil) SOIC Pin Descriptions Pin Number Pin Name Pin Type Pin Description 1 XI Input Crystal connection. Connect to the external pullable crystal. 2 VDD Power Connect to +3.3 V (0.01 µf decoupling capacitor recommended). 3 VIN Input Voltage input to VCXO – 0 to 3.3 V analog input which controls the oscillation frequency of the VCXO. 4 GND Power Connect to ground. 5 CLK Output Clock output. 6 NC — 7 GND Power Connect to ground. 8 X2 Input Crystal connection. Connect to the external pullable crystal. No internal connection (may connect to ground or VDD). IDT™ / ICS™ LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO 2 MK3727D REV M 030806 MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO VCXO AND SYNTHESIZER External Component Selection the MK3727D. There should be no vias between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal. The MK3727D requires a minimum number of external components for proper operation. Crystal Tuning Load Capacitors Decoupling Capacitor The crystal traces should include pads for small fixed capacitors, one between X1 and ground, and another between X2 and ground. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF. A decoupling capacitor of 0.01µF must be connected between VDD and GND, as close to these pins as possible. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. Series Termination Resistor The procedure for determining the value of these capacitors can be found in application note MAN05. When the PCB trace between the clock output (CLK, pin 5) and the load is over 1 inch, series termination should be used. To series terminate a 50Ω trace (a commonly used trace impedance), place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. Quartz Crystal The MK3727D VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device with the recommended parameters (shown below) must be used, and the layout guidelines discussed in the following section shown must be followed. The frequency of oscillation of a quartz crystal is determined by its “cut” and by the load capacitors connected to it. The MK3727D incorporates on-chip variable load capacitors that “pull” (change) the frequency of the crystal. The crystal specified for use with the MK3727D is designed to have zero frequency error when the total of on-chip + stray capacitance is 14 pF. Recommended Crystal Parameters: Initial Accuracy at 25°C Temperature Stability Aging Load Capacitance Shunt Capacitance, C0 C0/C1 Ratio Equivalent Series Resistance ±20 ppm ±30 ppm ±20 ppm 14 pf 7 pF Max 250 Max 35Ω Max The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as IDT™ / ICS™ LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO 3 MK3727D REV M 030806 MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO VCXO AND SYNTHESIZER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK3727D. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature 0 to +70°C Storage Temperature -65 to +150°C Soldering Temperature 260°C Recommended Operation Conditions Parameter Min. Max. Units 0 +70 °C +3.15 +3.45 V Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Typ. Reference crystal parameters Refer to page 3 DC Electrical Characteristics VDD=3.3 V ±5% , Ambient temperature 0 to +70°C, unless stated otherwise Parameter Symbol Conditions Operating Voltage VDD Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA Output High Voltage (CMOS Level) VOH IOH = -4 mA Operating Supply Current IDD Output = 27 MHz, no load Short Circuit Current IOS VIN, VCXO Control Voltage VIA IDT™ / ICS™ LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO Min. Typ. 3.15 Units 3.45 V 2.4 V 0.4 VDD-0.4 0 4 Max. V V 10 mA ±50 mA 3.3 MK3727D V REV M 030806 MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO VCXO AND SYNTHESIZER AC Electrical Characteristics VDD = 3.3 V ±5%, Ambient Temperature 0 to +70° C, unless stated otherwise Parameter Symbol Conditions Output Frequency FO VCXO Crystal frequency = 1/2 Output Crystal Pullability FP 0V< VIN < 3.3 V, Note 1 VCXO Gain Min. Typ. Max. Units 24 36 + 115 VIN = VDD/2 + 1 V, Note 1 MHz ppm 120 ppm/V Output Rise Time tOR 0.8 to 2.0 V, CL=15 pF 1.5 ns Output Fall Time tOF 2.0 to 0.8 V, CL=15 pF 1.5 ns Output Clock Duty Cycle tD Measured at 1.4 V, CL=15 pF 55 % Maximum Output Jitter, short term tJ CL=15 pF 45 50 100 ps Note 1: External crystal device must conform with Pullable Crystal Specifications listed on page 3. Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case IDT™ / ICS™ LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO Symbol Conditions Min. Typ. Max. Units θJA Still air 150 °C/W θJA 1 m/s air flow 140 °C/W θJA 3 m/s air flow 120 °C/W 40 °C/W θJC 5 MK3727D REV M 030806 MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO VCXO AND SYNTHESIZER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 Symbol E A A1 B C D E e H h L α H INDEX AREA 1 2 D A Min Max 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Inches Min Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° h x 45 A1 C -Ce B SEATING PLANE L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature MK3727D MK3727DTR MK3727DLF MK3727DLFTR MK3727D-DPK MK3727D MK3727D 3727DLF 3727DLF — Tubes Tape and Reel Tubes Tape and Reel Tested die in waffle pack 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 0 to +70°C 0 to +70°C 0 to +70°C 0 to +70°C 0 to +70°C Parts that are ordered with a “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. IDT™ / ICS™ LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO 6 MK3727D REV M 030806 MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO VCXO AND SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 IDT Europe, Limited Prime House Barnett Wood Lane Leatherhead, Surrey United Kingdom KT22 7DE +44 1372 363 339 © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.