MK3771-17R

DATASHEET MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE Description Features The MK3771-17 is a low cost, low jitter, high-perfomance VCXO and clock synthesizer designed for set-top boxes and HDTV receivers. The on-chip Voltage Controlled Crystal Oscillator accepts a 0 to 3.3 V input voltage to cause the output clocks to vary by ±100 ppm. Using IDT’s patented VCXO and analog Phase-Locked Loop (PLL) techniques, the device uses an inexpensive 13.5 MHz crystal input to produce multiple output clocks including selectable BCLK, a selectable audio clock, two communications clocks, a 13.5 MHz clock, and three 27 MHz clocks. All clocks are frequency locked to the 27 MHz output (and to each other) with zero ppm error, so any output can be used as the VCXO output. • • • • Packaged in 28-pin SSOP • • • • VCXO tuning voltage of 0 to 3.3 V Pb (lead) free package HDTV frequencies of 74.25 and 74.175824 MHz On-chip patented VCXO with pull range of 200 ppm (minimum) Supports Ethernet with 20 and 25 MHz clocks Modem clocks of 11.0592 and 24.576 MHz option Audio clocks support 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling rates • Zero ppm synthesis error in all clocks (all exactly track 27MHz VCXO) • • • • • Uses an inexpensive 13.5 MHz crystal Full CMOS output swings with 12 mA output drive capability at TTL levels Advanced, low power, sub-micron CMOS process 3.3 V ±5% operating supply Block Diagram AS2:0 3 BS1, BS0 2 Audio Clock PLL Clock Synthesis Circuitry CS VIN BCLK CCLK1 CCLK2 XI 13.5 MHz pullable crystal XO Voltage Controlled Crystal Oscillator 108 MHz or 27 MHz X8 PLL Divide Logic VS 54 MHz or 27 MHz 27 MHz 13.5 MHz or 27 MHz IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE 1 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER Pin Assignment B and C Clocks (MHz) BS0 1 28 AS1 X2 2 27 AS0 X1 3 26 VDD 4 VDD 5 VIN BS1 BS0 CS BCLK CCLK1 CCLK2 0 0 0 74.175 20 25 VCLK2 0 0 1 74.175 11.0592 24.576 25 VCLK1 0 1 0 74.25 20 25 24 GND 0 1 1 74.25 11.0592 24.576 6 23 VCLK4 VDD 7 22 M 0 0 5.06 20 25 VDD VDD 8 21 AS2 M 0 1 5.06 11.0592 24.576 CS 9 20 GND M 1 0 10.12 20 25 GND 10 19 GND M 1 1 10.12 11.0592 24.576 GND 11 18 VCLK3 1 0 0 48 20 25 BCLK 12 17 CCLK1 1 0 M 48 7.3728 24 VS 13 16 BS1 ACLK 14 15 1 0 1 48 11.0592 24.576 CCLK2 1 1 0 14.318 20 25 1 1 M 14.318 7.3728 28.636 1 1 1 14.318 11.0592 24.576 Audio Clocks (MHz) AS2 AS1 AS0 ACLK 0 0 0 8.192 0 0 1 11.2896 VS VCLK1 VCLK2 VCLK3 VCLK4 0 1 0 12.288 0 27 27 27 108 0 1 1 16.9344 M 27 54 13.5 108 1 0 0 16.384 1 27 27 27 27 1 0 1 22.5792 1 1 0 18.432 1 1 1 24.576 IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO Clocks (MHz) 2 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER Pin Descriptions Pin Number Pin Name Pin Type Pin Description 1 BS0 I 2 X2 XO Crystal connection. Connect to a pullable 13.5 MHz crystal. 3 X1 XI Crystal connection. Connect to a pullable 13.5 MHz crystal. 4, 5, 7, 8, 22 VDD P Connect to +3.3 V. 6 VIN I Analog control voltage for VCXO. Pulls outputs ±100 ppm by varying from 0 to 3.3 V. 9 CS TI Communications Clock Select. Selects CCLK 1 and 2 per table above. Internal pull-up. 10, 11, 19, 20, 24 GND P Connect to ground. 12 BCLK O B clock output. Determined by status of AS2:0 per table above. 13 VS TI VCXO Clock Select. Selects frequencies on VCLK1-VCLK4 per table above. 14 ACLK O Audio Clock Output. Determined by status of AS2:0 per table above. 15 CCLK2 O Communications Clock Output 2. Determined by status of CS per table above. 16 BS1 TI B Clock Select 1. Selects BCLK frequency. See table above. 17 CCLK1 O Communications Clock Output 1. Determined by status of CS per table above. 18 VCLK3 O VCXO Clock output 3. Can be either 27 or 13.5 MHz per table above. 21 AS2 I Audio Clock Select pin 2. Selects Audio clock on pin 14 per table above. Internal pull-up. 23 VCLK4 O VCXO Clock output 4. Can be either 27 or 108 MHz per table above. 25 VCLK1 O VCXO Clock output 1. Always 27 MHz. 26 VCLK2 O VCXO Clock output 2. Can be either 27 or 54 MHz per table above. 27 AS0 I Audio Clock Select pin 0. Selects Audio clock on pin 14 per table above. Internal pull-up. 28 AS1 I Audio Clock Select pin 1. Selects Audio clock on pin 14 per table above. Internal pull-up. B clock select 0. KEY: I = Input TI = Tri-level O = Output P = Power supply connection XI, XO= Crystal connections IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE 3 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER External Component Selection capacitors, one between X1 and ground, and another between X2 and ground. Stuffing of these capacitors on the PCB is optional. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF. The MK3771-17 requires a minimum number of external components for proper operation. Decoupling Capacitors Decoupling capacitors of 0.01µF should be connected between VDD and GND on pins 3 and 6, and on pins 13 and 14, as close to the MK3771-17 as possible. For optimum device performance, the decoupling capacitors should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. To determine the need for and value of the crystal adjustment capacitors, you will need a PC board of your final layout, a frequency counter capable of about 1 ppm resolution and accuracy, two power supplies, and some samples of the crystals which you plan to use in production, along with measured initial accuracy for each crystal at the specified crystal load capacitance, CL. Series Termination Resistor When the PCB traces between the clock outputs and the loads are over 1 inch, series termination should be used. To series terminate a 50Ω trace (a commonly used trace impedance) place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. To determine the value of the crystal capacitors: 1. Connect VDD of the MK3771-17 to 3.3 V. Connect pin 4 of the MK3771-17 to the second power supply. Adjust the voltage on pin 4 to 0V. Measure and record the frequency of the CLK output. Quartz Crystal 2. Adjust the voltage on pin 4 to 3.3 V. Measure and record the frequency of the same output. The MK3771-17 VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device with the recommended parameters must be used, and the layout guidelines discussed in the following section must be followed. To calculate the centering error: 6 ( f 3.3V – f t arg et ) + ( f 0V – f t arg et ) Error = 10 x ------------------------------------------------------------------------------ – error xtal f t arg et The frequency of oscillation of a quartz crystal is determined by its “cut” and by the load capacitors connected to it. The MK3771-17 incorporates on-chip variable load capacitors that “pull” (change) the frequency of the crystal. The crystal specified for use with the MK3771-17 is designed to have zero frequency error when the total of on-chip + stray capacitance is 14 pF. Where: ftarget = nominal crystal frequency errorxtal =actual initial accuracy (in ppm) of the crystal being measured The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as the MK3771-17. There should be no vias between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal. If the centering error is less than ±25 ppm, no adjustment is needed. If the centering error is more than 25ppm negative, the PC board has excessive stray capacitance and a new PCB layout should be considered to reduce stray capacitance. (Alternately, the crystal may be re-specified to a higher load capacitance. Contact IDT for details.) If the centering error is more than 25ppm positive, add identical fixed centering capacitors from each crystal pin to ground. The value for each of these caps (in pF) is given by: Please see application note MAN05 for recommended crystal parameters and suppliers. Crystal Tuning Load Capacitors The crystal traces should include pads for small fixed IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE 4 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER crystal vendor. If you do not know the value, assume it is 30 ppm/pF. After any changes, repeat the measurement to verify that the remaining error is acceptably low (typically less than ±25ppm). External Capacitor = 2 x (centering error)/(trim sensitivity) Trim sensitivity is a parameter which can be supplied by your Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK3771-17. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature 0 to +70° C Storage Temperature -65 to +150° C Junction Temperature 125° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature 0 Power Supply Voltage (measured in respect to GND) IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE Typ. 5 +3.15 +3.3 Max. Units +70 °C +3.45 V MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature 0 to +70° C Parameter Symbol Conditions Operating Voltage VDD Input High Voltage VIH Except TI pins Input Low Voltage VIL Except TI pins Input High Voltage VIH All TI pins Input Low Voltage VIL All TI pins Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOH = 12 mA Output High Voltage VOH CMOS level, IOH = -8 mA Operating Supply Current IDD No load, Note 1 Min. Typ. Max. Units 3.15 3.3 3.45 V 2 V 0.8 VDD-0.5 V 0.5 Input Capacitance V 0.4 V VDD-0.4 Each output V 28 mA 15 µA ±50 mA 5 pF CIN Frequency Synthesis Error V 2.4 Power Down Mode Supply Current Short Circuit Current V All clocks VIN, VCXO Control Voltage 0 0 ppm 3.3 V AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature 0 to +70° C Parameter Symbol Conditions Min. Typ. Max. 13.50000 Units Input Frequency FIN Output Clock Rise Time tOR 0.8 V to 2.0 V 1.5 ns Output Clock Fall Time tOF 2.0 V to 0.8 V 1.5 ns Output Clock Duty Cycle tOD At VDD/2 60 % 40 Maximum Absolute Jitter, short term VCXO Gain VIN = VDD/2 ±1 V Crystal Pullability 0V < VIN < 3.3 V, Note 2 ±100 MHz ±250 ps 100 ppm/V ppm Notes: 1. With all clocks at highest MHz. 2. With a pullable crystal that conforms to IDT’s specifications. IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE 6 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER Thermal Characteristics Parameter Symbol Conditions Min. Typ. Max. Units Thermal Resistance Junction to Ambient θJA Still air 100 ° C/W θJA 1 m/s air flow 80 ° C/W θJA 3 m/s air flow 67 ° C/W Thermal Resistance Junction to Case θJC 60 ° C/W Marking Diagram 28 Marking Diagram (Pb free) 15 28 MK3771-17R ###### YYWW 1 15 MK3771-17RLF ###### YYWW 14 1 14 Notes: 1. ###### is the lot code. 2. YYWW is the last two digits of the year, and the week number that the part was assembled. 3. “LF” designates Pb free packaging. IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE 7 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER Package Outline and Package Dimensions (28-pin SSOP, 150 mil Body, 0.025 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95, MO-153 28 Millimeters Symbol E1 A A1 A2 b C D E E1 e L α aaa E INDEX AREA 1 2 D A 2 Min Inches Max 1.35 1.75 0.10 0.25 -1.50 0.20 0.30 0.18 0.25 9.80 10.00 5.80 6.20 3.80 4.00 0.635 Basic 0.40 1.27 0° 8° -0.10 Min Max .053 .069 .0040 .010 -.059 .008 .012 .007 .010 .386 .394 .228 .244 .150 .157 0.025 Basic .016 .050 0° 8° -0.004 A A 1 c -Ce b SEATING PLANE L aaa C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature MK3771-17RLF MK3771-17RLF Tubes 28-pin SSOP 0 to +70° C MK3771-17RLFTR MK3771-17RLF Tape and Reel 28-pin SSOP 0 to +70° C “LF” denotes Pb (lead) free package. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ VCXO AND HDTV SET-TOP CLOCK SOURCE 8 MK3771-17 REV E 051310 MK3771-17 VCXO AND HDTV SET-TOP CLOCK SOURCE VCXO AND SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.