IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH® PRODUCTS
HIGH-SPEED CMOS 10-BIT
BUS EXCHANGE SWITCH
DESCRIPTION:
FEATURES:
•
•
•
•
•
•
The QS3383 provides ten high-speed CMOS TTL-compatible bus
switches. The low ON resistance of the QS3383 allows inputs to be
connected to outputs without adding propagation delay and without generating additional ground bounce noise. The Bus Enable (BE) signal turns
the switches on. The Bus Exchange (BX) signal provides nibble swap of
the AB and CD pairs of signals. This exchange configuration allows byte
swapping of buses in systems. It can also be used as a 5-wide 2-to-1
multiplexer and to create low delay barrel shifters, etc.
The QS3383 is characterized for operation at -40°C to +85°C.
Enhanced N channel FET with no inherent diode to Vcc
Ω bidirectional switches connect inputs to outputs
5Ω
Zero propagation delay, zero added ground bounce
Undershoot clamp diodes on all switch and control inputs
Bus exchange allows nibble swap
Available in QSOP package
APPLICATIONS:
•
•
•
•
IDTQS3383
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Resource sharing
Crossbar switching
FUNCTIONAL BLOCK DIAGRAM
A0
C0
B0
D0
A4
C4
B4
D4
BX
BE
INDUSTRIAL TEMPERATURE RANGE
c 2011 Integrated Device Technology, Inc.
OCTOBER 2011
1
DSC-5571/5
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS(1)
PIN CONFIGURATION
Symbol
Description
Max
Unit
1
2
24
VCC
VTERM(2)
Supply Voltage to Ground
–0.5 to +7
V
23
D4
VTERM(3)
DC Switch Voltage VS
–0.5 to +7
V
VTERM(3)
DC Input Voltage VIN
–0.5 to +7
V
A0
3
22
B4
VAC
AC Input Voltage (pulse width ≤20ns)
–3
V
B0
4
21
A4
IOUT
DC Output Current
120
mA
PMAX
Maximum Power Dissipation (TA = 85°C)
0.5
W
D0
5
20
C4
TSTG
Storage Temperature
–65 to +150
°C
C1
6
19
D3
A1
7
18
B3
B1
8
17
A3
D1
9
16
C3
C2
10
15
D2
A2
11
14
B2
12
13
BX
BE
C0
GND
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. VCC terminals.
3. All terminals except VCC .
CAPACITANCE (TA = +25°C, f = 1MHz, VIN = 0V, VOUT = 0V)
QSOP
TOP VIEW
Pins
Typ.
Max. (1)
Unit
Control Inputs
3
5
pF
Quickswitch Channels (Switch OFF)
5
7
pF
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
I/O
A0 - A4 , B0 - B 4
I/O
Description
C0 - C4, D0 - D4
I/O
BE
I
Bus Switch Enable
BX
I
Bus Exchange
A and B Buses
C and D Buses
FUNCTION TABLE(1)
BE
BX
A0 - A4
B0 - B4
Function
H
X
Hi-Z
Hi-Z
Disconnect
L
L
C0 - C 4
D0 - D 4
Connect
L
H
D0 - D 4
C0 - C 4
Exchange
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
Z = High-Impedance
2
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5V ± 5%
Symbol
Parameter
Test Conditions
Min.
VIH
Input HIGH Voltage
Guaranteed Logic HIGH for Control Pins
2
VIL
Input LOW Voltage
Guaranteed Logic LOW for Control Pins
IIN
Input Leakage Current (Control Inputs)
0V ≤ VIN ≤ VCC
Typ.(1) Max.
Unit
—
—
V
—
—
0.8
V
—
0.01
±1
μA
I OZ
Off-State Current (Hi-Z)
0V ≤ VOUT ≤ VCC, Switches OFF
—
0.01
±1
μA
RON
Switch ON Resistance(2)
VCC = Min., VIN = 0V, ION = 30mA
—
6
8
Ω
VCC = Min., VIN = 2.4V, ION = 15mA
—
12
17
VP
Pass Voltage(3)
VIN = VCC = 5V, IOUT = -5μA
3.7
4
4.2
NOTES:
1. Typical values are at VCC = 5V and TA = 25°C.
2. RON is guaranteed but not production tested.
3. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs VIN AT VCC = 5V
16
14
R ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
V IN
(Volts)
3
2.5
3.0
3.5
V
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
Test Conditions(1)
Parameter
Max.
Unit
ICCQ
Quiescent Power Supply Current
VCC = Max., VIN = GND or VCC, f = 0
1.5
mA
ΔICC
Power Supply Current per Input HIGH(2)
VCC = Max., VIN = 3.4V, f = 0
2.5
mA
ICCD
Dynamic Power Supply Current per MHz
VCC = Max., A and B Pins Open, Control Inputs Toggling @ 50% Duty Cycle
0.25
mA/MHz
(3)
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TTL-driven input (VIN = 3.4V, control inputs only). A, B,C, and D pins do not contribute to ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
TA = -40°C to +85°C, VCC = 5V ± 5%
CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted.
Symbol
Min. (1)
Parameter
Typ.
Max.
Unit
⎯
⎯
0.25(3)
ns
tPLH
tPHL
Data Propagation Delay(2)
tPZL
tPZH
Switch Turn-On Delay
BE to Ax, Bx, Cx, Dx
1.5
⎯
6.5
ns
tPLZ
Switch Turn-Off Delay(2)
1.5
⎯
5.5
ns
tPHZ
BE to Ax, Bx, Cx, Dx
tBX
Switch Multiplex Delay
BX to Ax, Bx, Cx, Dx
1.5
⎯
6.5
ns
AxBx to CxDx, CxDx to AxBx
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Process
X
Blank
8
Tube or Tray
Tape and Reel
Blank
Industrial (-40°C to +85°C)
QG
Quarter Size Outline Package - Green
3383
High Speed CMOS 10-Bit Bus Exchange Switch
5
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.