QS3VH2245PAG

IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH® PRODUCTS 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH FEATURES: IDTQS3VH2245 DESCRIPTION: • N channel FET switches with no parasitic diode to VCC – Isolation under power-off conditions – No DC path to VCC or GND – 5V tolerant in OFF and ON state • 5V tolerant I/Os • Flat RON characteristics over operating range • Rail-to-rail switching 0 - 5V • Bidirectional dataflow with near-zero delay: no added ground bounce • Excellent RON matching between channels • VCC operation: 2.3V to 3.6V • High bandwidth • LVTTL-compatible control Inputs • Undershoot Clamp Diodes on all switch and control Inputs • Low I/O capacitance, 4pF typical Ω resistors for low noise and line matching • 25Ω • Available in QSOP and TSSOP packages The QS3VH2245 is a high bandwidth 8-bit bus switch. The QS3VH2245, with 25Ω ON resistance and 1.35ns propagation delay, is ideal for line matching and low noise environments. The switches can be turned ON under the control of the LVTTL-compatible Output Enable signal for bidirectional data flow with no added delay or ground bounce. In the ON state, the switches can pass signals up to 5V. In the OFF state, the switches offer very high impedence at the terminals. The combination of small propagation delay, high OFF impedance, and over-voltage tolerance makes the QS3VH2245 ideal for high performance communication applications. The QS3VH2245 is characterized for operation from -40°C to +85°C. APPLICATIONS: • • • • Hot-swapping Low distortion analog switch Replaces mechanical relay ATM 25/155 switching FUNCTIONAL BLOCK DIAGRAM A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B2 B3 B4 B5 B6 B7 OE The IDT logo is a registered trademark of Integrated Device Technology, Inc. FEBRUARY 2014 INDUSTRIAL TEMPERATURE RANGE 1 c 2014 Integrated Device Technology, Inc. DSC-5591/9 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION NC 1 20 VCC A0 A1 2 3 19 OE 18 B0 A2 4 17 B1 A3 5 16 B2 A4 6 15 B3 A5 7 14 B4 A6 8 13 B5 A7 9 12 B6 GND 10 11 B7 Symbol Description VTERM(2) SupplyVoltage to Ground Max Unit –0.5 to +4.6 V VTERM(3) DC Switch Voltage VS –0.5 to +5.5 V VTERM(3) DC Input Voltage VIN –0.5 to +5.5 V VAC AC Input Voltage (pulse width ≤20ns) –3 V IOUT DC Output Current (max. sink current/pin) 120 mA TSTG Storage Temperature –65 to +150 °C NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VCC terminals. 3. All terminals except VCC . CAPACITANCE 0V) Symbol QSOP/ TSSOP TOP VIEW (TA = +25°C, F = 1MHz, VIN = 0V, VOUT = (1) Parameter Typ. Max. Unit 3 5 pF CIN Control Inputs CI/O Quickswitch Channels (Switch OFF) 4 6 pF CI/O Quickswitch Channels (Switch ON) 8 12 pF NOTE: 1. This parameter is guaranteed but not production tested. PIN DESCRIPTION Pin Names Description OE Output Enable Ax Data I/Os Bx Data I/Os FUNCTION TABLE(1) Function OE H Disconnected L Connect (Ax = Bx) NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level 2 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = –40°C to +85°C, VCC = 3.3V ±0.3V Symbol VIH VIL Parameter Test Conditions Input HIGH Voltage Input LOW Voltage Min. Typ.(1) Max. Guaranteed Logic HIGH VCC = 2.3V to 2.7V 1.7 — — for Control Inputs VCC = 2.7V to 3.6V 2 — — Guaranteed Logic LOW VCC = 2.3V to 2.7V — — 0.7 for Control Inputs VCC = 2.7V to 3.6V — — 0.8 Unit V V IIN Input Leakage Current (Control Inputs) 0V ≤ VIN ≤ VCC — — ±1 μA IOZ Off-State Current (Hi-Z) 0V ≤ VOUT ≤ 5V, Switches OFF — — ±1 μA IOFF Data Input/Output Power Off Leakage VIN or VOUT 0V to 5V, VCC = 0V — — ±1 μA VCC = 2.3V VIN = 0V ION = 30mA 18 27 39 RON Switch ON Resistance Typical at VCC = 2.5V VIN = 1.7V ION = 15mA 18 28 41 VCC = 3V VIN = 0V ION = 30mA 18 25 38 VIN = 2.4V ION = 15mA 18 26 40 Ω NOTE: 1. Typical values are at VCC = 3.3V and TA = 25°C. TYPICAL ON RESISTANCE vs VIN AT VCC = 3.3V 40 RON (ohms) 35 30 25 20 15 10 5 0 0 0.5 1 1.5 2 VIN (Volts) 3 2.5 3 3.5 4 4.5 5 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol Test Conditions(1) Parameter Min. Typ. Max. Unit ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or VCC, f = 0 — 2 4 mA ΔICC Power Supply Current (2,3) per Input HIGH VCC = Max., VIN = 3V, f = 0 per Control Input — — 30 μA ICCD Dynamic Power Supply Current VCC = 3.3V, A and B Pins Open, Control Inputs See Typical ICCD vs Enable Frequency graph below (4) Toggling @ 50% Duty Cycle NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Per input driven at the specified level. A and B pins do not contribute to ΔIcc. 3. This parameter is guaranteed but not tested. 4. This parameter represents the current required to switch internal capacitance at the specified frequency. The A and B inputs do not contribute to the Dynamic Power Supply Current. This parameter is guaranteed but not production tested. TYPICAL ICCD vs ENABLE FREQUENCY CURVE AT VCC = 3.3V 12 10 ICCD (mA) 8 6 4 2 0 0 2 4 6 8 10 12 ENABLE FREQUENCY (MHz) 4 14 16 18 20 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40°C to +85°C VCC = 2.5 ± 0.2V (1) Symbol tPLH tPHL tPZL tPZH tPLZ tPHZ fOE Parameter Data Propagation Delay(2,3) Ax to/from Bx Switch Turn-On Delay OE to Ax/Bx Switch Turn-Off Delay OE to Ax/Bx Operating Frequency - Enable, Select(2,5) VCC = 3.3 ± 0.3V (1) Min. (4) ⎯ Max. 0.9 Min. (4) ⎯ Max. 1.35 Unit ns 1.5 9 1.5 8 ns 1.5 7.5 1.5 7.5 ns ⎯ 10 ⎯ 20 MHz NOTES: 1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS. 2. This parameter is guaranteed but not production tested. 3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 1.35ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4. Minimums are guaranteed but not production tested. 5. Maximum toggle frequency for OE control input (pass voltage > VCC, VIN = 5V, RLOAD ≥ 1MΩ, no CLOAD). 5 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE SOME APPLICATIONS FOR HOTSWITCH PRODUCTS NFET 0 to +5V Vcc = 3.3V OE 0 to +5V +6.5V CHARGE PUM P DRIVER SINGLE HOT SW ITCH Rail-to-Rail Switching ZERO DOW N TIM E SYSTEM PLUG GABLE CAR D/ LIVE SYSTEM CARD I/O ON CARD LOGIC CONNECTOR QS3VH XXX CARD I/O ON CARD LOGIC CONNECTOR QS3VH XXX CPU RAM BUS Hot-Swapping 6 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VCC = 3.3V ± 0.3V VCC = 2.5V ± 0.2V Unit VLOAD 6 2 x Vcc V VIH 3 Vcc V (1) (2) VT 1.5 VCC/2 V VLZ 300 150 mV VHZ 300 150 mV CL 50 30 pF SAME PHASE INPUT TRANSITION tPLH tPHL tPLH tPHL OUTPUT VIH VT 0V VOH VT VOL VIH VT 0V OPPOSITE PHASE INPUT TRANSITION Propagation Delay VLOAD VCC 500Ω Pulse(1, 2) Generator VIN CONTROL INPUT GND tPZL VOUT D.U.T. RT DISABLE ENABLE Open OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH 500Ω CL tPLZ VLOAD/2 VT tPHZ VT 0V Test Circuits for All Outputs VIH VT 0V VLOAD/2 VOL + VLZ VOL VOH VOH -VHZ 0V NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. Enable and Disable Times DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns. SWITCH POSITION Test Switch tPLZ/tPZL VLOAD tPHZ/tPZH GND tPD Open 7 IDTQS3VH2245 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION QS XXXXX XX Device Type Package X Blank 8 Tube or Tray Tape and Reel QG PAG QSOP - Green TSSOP - Green 3VH2245 2.5V / 3.3V 8-Bit High Bandwidth Bus Switch Datasheet Document History 09/01/08 Pg. 4, 8 02/24/14 Pg. 1, 8 Revise ICCQ Typ. and Max. Remove non green package version and updated the ordering information by removing the “IDT” notation. Updated the Ordering Information by Adding Tape and Reel information. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 8 for Tech Support: logichelp@idt.com IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.