IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
IDTQS3VH253
QUICKSWITCH® PRODUCTS
2.5V / 3.3V DUAL 4:1 MUX/DEMUX
HIGH BANDWIDTH BUS SWITCH
FEATURES:
DESCRIPTION:
• N channel FET switches with no parasitic diode to VCC
– Isolation under power-off conditions
– No DC path to VCC or GND
– 5V tolerant in OFF and ON state
• 5V tolerant I/Os
Ω typical
• Low RON - 4Ω
• Flat RON characteristics over operating range
• Rail-to-rail switching 0 - 5V
• Bidirectional dataflow with near-zero delay: no added ground
bounce
• Excellent RON matching between channels
• VCC operation: 2.3V to 3.6V
• High bandwidth - up to 500MHz
• LVTTL-compatible control Inputs
• Undershoot Clamp Diodes on all switch and control Inputs
• Low I/O capacitance, 4pF typical
• Available in QSOP and TSSOP packages
The QS3VH253 HotSwitch Dual 4:1 multiplexer/demultiplexer is a high
bandwidth bus switch. The QS3VH253 has very low ON resistance,
resulting in under 250ps propagation delay through the switch. The Select
(Sx) inputs control the data flow. The multiplexers/demultiplexers are
enabled when the Enable (EA, EB) inputs are low. In the ON state, the
switches can pass signals up to 5V. In the OFF state, the switches offer very
high impedance at the terminals.
The combination of near-zero propagation delay, high OFF impedance,
and over-voltage tolerance makes the QS3VH253 ideal for high performance communication applications.
The QS3VH253 is characterized for operation from -40°C to +85°C.
APPLICATIONS:
•
•
•
•
•
Hot-swapping
Multiplexing/demultiplexing
Low distortion analog switch
Replaces mechanical relay
ATM 25/155 switching
FUNCTIONAL BLOCK DIAGRAM
S0
S1
EA
EB
I0 A
I1 A
YA
I2 A
I3 A
I0 B
I1 B
YB
I2 B
I3 B
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
FEBRUARY 2014
1
c
2014 Integrated Device Technology, Inc.
DSC-5945/11
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
ABSOLUTE
PIN CONFIGURATION
Symbol
VTERM(2)
EA
1
16
VCC
S1
2
15
EB
I3A
3
14
S0
I2A
4
13
I3B
I1A
5
12
I2B
I0A
6
11
I1B
YA
GND
7
8
10
9
I0B
YB
INDUSTRIAL TEMPERATURE
RANGE
(1)
MAXIMUM RATINGS
Description
SupplyVoltage to Ground
–0.5 to +4.6
V
VTERM(3) DC Switch Voltage VS
–0.5 to +5.5
V
VTERM(3)
DC Input Voltage VIN
–0.5 to +5.5
V
VAC
AC Input Voltage (pulse width ≤20ns)
–3
V
IOUT
DC Output Current (max. sink current/pin)
120
mA
TSTG
Storage Temperature
–65 to +150
°C
CAPACITANCE
0V)
Symbol
(TA = +25°C, F = 1MHz, VIN = 0V, VOUT =
Parameter(1)
Typ.
CIN
Control Inputs
CI/O
Quickswitch Channels
(Switch OFF)
CI/O
Quickswitch Channels
(Switch ON)
3
5
pF
6
pF
Mux
11
15
Demux
12
16
Mux
12
16
PIN DESCRIPTION
EA
EB
S1
S0
YA
YB
Function
H
X
X
X
Z
X
Disable A
X
H
X
X
X
Z
Disable B
L
L
L
L
I0A
I0B
S1 - 0 = 0
EA, EB
I
Enable Input
YA, YB
O
Data Outputs
L
L
L
H
I1A
I1B
S1 - 0 = 1
L
L
H
L
I2A
I2B
S1 - 0 = 2
L
L
H
H
I3A
I3B
S1 - 0 = 3
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
Z = High-Impedence
2
Unit
4
FUNCTION TABLE(1)
Outputs
Max.
Demux
NOTE:
1. This parameter is guaranteed but not production tested.
Select
Unit
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. VCC terminals.
3. All terminals except VCC .
QSOP/ TSSOP
TOP VIEW
Enable
Max
Pin Names
I/O
Description
Ixx
I
Data Inputs
S0, S1
I
Select Input
pF
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 3.3V ±0.3V
Symbol
VIH
VIL
Parameter
Test Conditions
Input HIGH Voltage
Input LOW Voltage
Min.
Typ.(1) Max.
Guaranteed Logic HIGH
VCC = 2.3V to 2.7V
1.7
—
—
for Control Inputs
VCC = 2.7V to 3.6V
2
—
—
Guaranteed Logic LOW
VCC = 2.3V to 2.7V
—
—
0.7
for Control Inputs
VCC = 2.7V to 3.6V
—
—
0.8
IIN
Input Leakage Current (Control Inputs)
0V ≤ VIN ≤ VCC
—
—
±1
Unit
V
V
μA
IOZ
Off-State Current (Hi-Z)
0V ≤ VOUT ≤ 5V, Switches OFF
—
—
±1
μA
IOFF
Data Input/Output Power Off Leakage
VIN or VOUT 0V to 5V, VCC = 0V
—
—
±1
μA
VCC = 2.3V
VIN = 0V
ION = 30mA
—
6
8
RON
Switch ON Resistance
Typical at VCC = 2.5V
VIN = 1.7V
ION = 15mA
—
7
9
VCC = 3V
VIN = 0V
ION = 30mA
—
4
6
VIN = 2.4V
ION = 15mA
—
5
8
Ω
NOTE:
1. Typical values are at VCC = 3.3V and TA = 25°C.
TYPICAL ON RESISTANCE vs VIN AT VCC = 3.3V
16
14
RON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
VIN
(Volts)
3
3.0
3.5
4.0
4.5
5.0
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE
RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
Test Conditions(1)
Parameter
Min.
Typ.
Max.
Unit
ICCQ
Quiescent Power Supply Current
VCC = Max., VIN = GND or VCC, f = 0
—
2
4
mA
ΔICC
Power Supply Current (2,3) per Input HIGH
VCC = Max., VIN = 3V, f = 0 per Control Input
—
—
30
μA
ICCD
Dynamic Power Supply Current
VCC = 3.3V, A and B Pins Open, Control Inputs
(4)
See Typical ICCD vs Enable Frequency graph below
Toggling @ 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per input driven at the specified level. Mux/demux pins do not contribute to ΔIcc.
3. This parameter is guaranteed but not tested.
4. This parameter represents the current required to switch internal capacitance at the specified frequency. The mux/demux inputs do not contribute to the Dynamic Power Supply Current.
This parameter is guaranteed but not production tested.
TYPICAL ICCD vs ENABLE FREQUENCY CURVE AT VCC = 3.3V
6
ICCD (mA)
4
2
0
0
2
4
6
8
10
12
ENABLE FREQUENCY (MHz)
4
14
16
18
20
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
TA = -40°C to +85°C
VCC = 2.5 ± 0.2V (1)
Symbol
tPLH
tPHL
tSEL
tPZH
tPZL
tPHZ
tPLZ
tPZH
tPZL
tPHZ
tPLZ
fExorSx
Parameter
Data Propagation Delay(2,3)
Yx to Ixx or Ixx to Yx
Select Time
S to Yx
Enable Time
Sx to Ixx
Disable Time
Sx to Ixx
Enable Time
Ex to Yx or Ixx
Disable Time
Ex to Yx or Ixx
Operating Frequency - Enable(2,5)
Min. (4)
VCC = 3.3 ± 0.3V (1)
⎯
Max.
0.2
Min. (4)
⎯
Max.
0.2
Unit
ns
1.5
9
1.5
8
ns
1.5
9
1.5
9
ns
1.5
8
1.5
8
ns
1.5
9
1.5
8
ns
1.5
8
1.5
8
ns
⎯
10
⎯
20
MHz
NOTES:
1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the
order of 0.2ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation
delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
4. Minimums are guaranteed but not production tested.
5. Maximum toggle frequency for Sx or Ex control input (pass voltage > VCC, VIN = 5V, RLOAD ≥ 1MΩ, no CLOAD).
5
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE
RANGE
SOME APPLICATIONS FOR HOTSWITCH PRODUCTS
NFET
0 to +5V
Vcc = 3.3V
OE
0 to +5V
+6.5V
CHARGE PUM P
DRIVER
SINGLE HOT
SW ITCH
Rail-to-Rail Switching
M ULTIPLEXING
CONTROL CIRCUITRY
1
CPU
M EM ORY
4 BANKS
4
M EM ORY
Multiplexing/Demultiplexing
ZERO DOW N TIME SYSTEM
PLUG GABLE CAR D/ LIVE SYSTEM
CARD I/O
ON CARD
LOGIC
CONNECTOR
QS3VH XXX
CARD I/O
ON CARD
LOGIC
CONNECTOR
QS3VH XXX
CPU
RAM
BUS
Hot-Swapping
6
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS
TEST CONDITIONS
Symbol
VCC = 3.3V ± 0.3V
VCC = 2.5V ± 0.2V
Unit
VLOAD
6
2 x Vcc
V
VIH
3
Vcc
V
(1)
(2)
VT
1.5
VCC/2
V
VLZ
300
150
mV
VHZ
300
150
mV
CL
50
30
pF
SAME PHASE
INPUT TRANSITION
tPLH
tPHL
tPLH
tPHL
OUTPUT
VIH
VT
0V
VOH
VT
VOL
VIH
VT
0V
OPPOSITE PHASE
INPUT TRANSITION
Propagation Delay
VLOAD
VCC
500Ω
Pulse(1, 2)
Generator
VIN
CONTROL
INPUT
GND
tPZL
VOUT
D.U.T.
RT
DISABLE
ENABLE
Open
OUTPUT
SWITCH
NORMALLY
CLOSED
LOW
tPZH
OUTPUT SWITCH
NORMALLY
OPEN
HIGH
500Ω
CL
tPLZ
VLOAD/2
VT
tPHZ
VT
0V
Test Circuits for All Outputs
VIH
VT
0V
VLOAD/2
VOL + VLZ
VOL
VOH
VOH -VHZ
0V
NOTE:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
Enable and Disable Times
DEFINITIONS:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
NOTES:
1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns.
SWITCH POSITION
Test
Switch
tPLZ/tPZL
VLOAD
tPHZ/tPZH
GND
tPD
Open
7
IDTQS3VH253
2.5V / 3.3V DUAL 4:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE
RANGE
ORDERING INFORMATION
QS
XXXXX
XX
Device Type Package
X
Blank
8
Tube or Tray
Tape and Reel
QG
PAG
QSOP - Green
TSSOP - Green
3VH253
2.5V / 3.3V Dual 4:1 Mux/Demux
High Bandwidth Bus Switch
Datasheet Document History
09/01/08
Pg. 4, 8
02/24/14
Pg. 8
Revise ICCQ Typ. and Max. Remove non green package version and updated the ordering
information by removing the “IDT” notation.
Updated the Ordering Information by Adding Tape and Reel information.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
8
for Tech Support:
logichelp@idt.com
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.