0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
X9313WSIZT1

X9313WSIZT1

  • 厂商:

    RENESAS(瑞萨)

  • 封装:

    SOIC8_150MIL

  • 描述:

    数字控制电位计(XDCP™) 线性,32抽头,3线接口,端子电压±VCC

  • 数据手册
  • 价格&库存
X9313WSIZT1 数据手册
DATASHEET X9313 FN8177 Rev 7.00 October 7, 2015 Digitally Controlled Potentiometer (XDCP™) Linear, 32 Taps, 3 Wire Interface, Terminal Voltages ± VCC The Intersil X9313 is a digitally controlled potentiometer (XDCP). The device consists of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by a 3-wire interface. Features The potentiometer is implemented by a resistor array composed of 31 resistive elements and a wiper switching network. Between each element and at either end are tap points accessible to the wiper terminal. The position of the wiper element is controlled by the CS, U/D, and INC inputs. The position of the wiper can be stored in nonvolatile memory and then be recalled upon a subsequent power-up operation. • 32 wiper tap points - Wiper position stored in nonvolatile memory and recalled on power-up • 31 resistive elements - Temperature compensated - End-to-end resistance range ±20% - Terminal voltages, -VCC to +VCC The device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications including: • Control • Solid-state potentiometer • 3-wire serial interface • Low power CMOS - VCC = 3V or 5V - Active current, 3mA max. - Standby current, 500µA max. • High reliability - Endurance, 100,000 data changes per bit - Register data retention, 100 years • Parameter adjustments • Signal processing • RTOTAL values = 1k, 10k, 50k • Packages - 8 Ld SOIC, 8 Ld MSOP and 8 Ld PDIP • Pb-free available (RoHS compliant) Block Diagram DECODER U/D INC CS VCC (SUPPLY VOLTAGE) CONTROL AND MEMORY DEVICE SELECT (CS) RH/VH 31 30 29 RH/VH UP/DOWN (U/D) INCREMENT (INC) 5-BIT UP/DOWN COUNTER 5-BIT NONVOLATILE MEMORY RW/VW RL/VL 28 ONE OF THIRTY-TWO OUTPUTS ACTIVE AT A TIME TRANSFER GATES RESISTOR ARRAY 2 VSS (GROUND) GENERAL VCC VSS STORE AND RECALL CONTROL CIRCUITRY 1 0 RL/VL RW/VW DETAILED FN8177 Rev 7.00 October 7, 2015 Page 1 of 12 X9313 Ordering Information PART NUMBER PART MARKING VCC RANGE (V) RTOTAL (k) TEMPERATURE RANGE (°C) 4.5 to 5.5 50 -40 to +85 8 Ld MSOP (Pb-free) M8.118 PACKAGE PKG. DWG. # X9313UMIZ* (Note) DDB X9313USZ* (Note) X9313U Z 0 to +70 8 Ld SOIC (Pb-free) M8.15 X9313USIZ* (Note) X9313U ZI -40 to +85 8 Ld SOIC (Pb-free) M8.15 X9313WMZ* (Note) DDF 0 to +70 8 Ld MSOP (Pb-free) M8.118 X9313WMIZ* (Note) DDE -40 to +85 8 Ld MSOP (Pb-free) M8.118 X9313WPIZ X9313WP ZI -40 to +85 8 Ld PDIP*** (Pb-free) MDP0031 X9313WSZ* (Note) X9313W Z 0 to +70 8 Ld SOIC (Pb-free) M8.15 X9313WSIZ* (Note) X9313WS ZI -40 to +85 8 Ld SOIC (Pb-free) M8.15 X9313ZMZ* (Note) DDJ 0 to +70 8 Ld MSOP (Pb-free) M8.118 X9313ZMIZ* (Note) DDH -40 to +85 8 Ld MSOP (Pb-free) M8.118 X9313ZSZ* (Note) X9313 Z 0 to +70 8 Ld SOIC (Pb-free) M8.15 10 1 X9313ZSIZ* (Note) X9313ZS ZI 8 Ld SOIC (Pb-free) M8.15 X9313UMZ* (Note) DDC 3 to 5.5 50 -40 to +85 0 to +70 8 Ld MSOP M8.118 X9313UMZ-3* (Note) DDD 3 to 5.5 50 0 to +70 8 Ld MSOP M8.118 X9313UMIZ-3* (Note) 13UEZ -40 to +85 8 Ld MSOP (Pb-free) M8.118 X9313USZ-3* (Note) X9313U ZD 0 to +70 8 Ld SOIC (Pb-free) M8.15 X9313WMZ-3* (Note) DDG 0 to +70 8 Ld MSOP (Pb-free) M8.118 X9313WMIZ-3* (Note) 13WEZ -40 to +85 8 Ld MSOP (Pb-free) M8.118 X9313WSZ-3* (Note) X9313W ZD 0 to +70 8 Ld SOIC (Pb-free) M8.15 X9313ZMZ-3* (Note) DDK X9313ZMIZ-3* (Note) 13ZEZ X9313ZSZ-3* (Note) X9313ZSIZ-3* (Note) 10 1 0 to +70 8 Ld MSOP (Pb-free) M8.118 -40 to +85 8 Ld MSOP (Pb-free) M8.118 X9313Z ZD 0 to +70 8 Ld SOIC (Pb-free) M8.15 X9313Z ZE -40 to +85 8 Ld SOIC (Pb-free) M8.15 NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. *Add “T1” suffix for tape and reel. Please refer to TB347 for details on reel specifications. **Add "T2" suffix for tape and reel. Please refer to TB347 for details on reel specifications. ***Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. Pin Descriptions Up/Down (U/D) RH/VH and RL/VL The U/D input controls the direction of the wiper movement and whether the counter is incremented or decremented. The high (RH/VH) and low (RL/VL) terminals of the X9313 are equivalent to the fixed terminals of a mechanical potentiometer. The terminology of RL/VL and RH/VH references the relative position of the terminal in relation to wiper movement direction selected by the U/D input and not the voltage potential on the terminal. Increment (INC) The INC input is negative-edge triggered. Toggling INC will move the wiper and either increment or decrement the counter in the direction indicated by the logic level on the U/D input. RW/VW RW/VW is the wiper terminal and is equivalent to the movable terminal of a mechanical potentiometer. The position of the wiper within the array is determined by the control inputs. The wiper terminal series resistance is typically 40 at VCC = 5V. FN8177 Rev 7.00 October 7, 2015 Page 2 of 12 X9313 Chip Select (CS) The device is selected when the CS input is LOW. The current counter value is stored in nonvolatile memory when CS is returned HIGH while the INC input is also HIGH. After the store operation is complete, the X9313 will be placed in the low power standby mode until the device is selected once again. Pinouts X9313 (8 LD PDIP, 8 LD SOIC) TOP VIEW INC 1 U/D 2 RH/VH 3 VSS 4 X9313 8 VCC 7 CS 6 RL/VL 5 RW/VW X9313 (8 LD MSOP) TOP VIEW RH/VH VSS RW/VW RL/VL 1 2 3 X9313 4 8 U/D 7 INC 6 VCC 5 CS TABLE 1. PIN NAMES SYMBOL DESCRIPTION RH/VH High terminal RW/VW Wiper terminal RL/VL Low terminal VSS Ground VCC Supply voltage U/D Up/Down control input INC Increment control input CS Chip Select control input Principles of Operation There are three sections of the X9313: the input control, counter and decode section; the nonvolatile memory; and the resistor array. The input control section operates just like an up/down counter. The output of this counter is decoded to turn on a single electronic switch connecting a point on the resistor array to the wiper output. Under the proper conditions, the contents of the counter can be stored in nonvolatile memory and retained for future use. The resistor array is comprised of 31 individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper. FN8177 Rev 7.00 October 7, 2015 The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. That is, the counter does not wrap around when clocked to either extreme. The electronic switches on the device operate in a “make before break” mode when the wiper changes tap positions. If the wiper is moved several positions, multiple taps are connected to the wiper for tIW (INC to VW change). The RTOTAL value for the device can temporarily be reduced by a significant amount if the wiper is moved several positions. When the device is powered-down, the last wiper position stored will be maintained in the nonvolatile memory. When power is restored, the contents of the memory are recalled and the wiper is set to the value last stored. Instructions and Programming The INC, U/D and CS inputs control the movement of the wiper along the resistor array. With CS set LOW the device is selected and enabled to respond to the U/D and INC inputs. HIGH to LOW transitions on INC will increment or decrement (depending on the state of the U/D input) a seven bit counter. The output of this counter is decoded to select one of thirty-two wiper positions along the resistive array. The value of the counter is stored in nonvolatile memory whenever CS transitions HIGH while the INC input is also HIGH. The system may select the X9313, move the wiper and deselect the device without having to store the latest wiper position in nonvolatile memory. After the wiper movement is performed as previously described and once the new position is reached, the system must keep INC LOW while taking CS HIGH. The new wiper position will be maintained until changed by the system or until a power-up/down cycle recalled the previously stored data. This procedure allows the system to always power-up to a preset value stored in nonvolatile memory; then during system operation, minor adjustments could be made. The adjustments might be based on user preference, system parameter changes due to temperature drift, etc. The state of U/D may be changed while CS remains LOW. This allows the host system to enable the device and then move the wiper up and down until the proper trim is attained. TABLE 2. MODE SELECTION CS INC U/D MODE L H Wiper up L L Wiper down H X Store wiper position X X Standby current L X No store, return to standby H Page 3 of 12 X9313 TABLE 2. MODE SELECTION CS INC U/D MODE L H Wiper up (not recommended) L L Wiper down (not recommended) Symbol Table WAVEFORM FN8177 Rev 7.00 October 7, 2015 INPUTS OUTPUTS Must be steady Will be steady May change from Low to High Will change from Low to High May change from High to Low Will change from High to Low Don’t Care: Changes Allowed Changing: State Not Known N/A Center Line is High Impedance Page 4 of 12 X9313 Absolute Maximum Ratings Recommended Operating Conditions Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Voltage on CS, INC, U/D, and VCC with Respect to VSS . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V Voltage on VH, VL, VW with respect to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . -6V to +7V V = |VH - VL|: X9313Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4V X9313W, X9313U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±8.8mA ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200V Temperature: Commercial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C Supply Voltage (VCC): X9313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±10% X9313-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 5.5V Max Wiper current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±4.4mA Power rating: RTOTAL  10k . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mW RTOTAL 1k . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mW Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. Potentiometer Characteristics Over recommended operating conditions, unless otherwise stated. LIMITS SYMBOL PARAMETER TEST CONDITIONS MIN TYP End-to-end Resistance Tolerance MAX UNIT ±20 % VVH VH Terminal Voltage -VCC +VCC V VVL VL Terminal Voltage -VCC +VCC V RW Wiper Resistance 100  IW Wiper Current ±4.4 mA Noise (Note 5) IW = (VH - VL)/RTOTAL, VCC = 5V Ref: 1kHz Resolution CH/CL/CW (Note 5) Absolute Linearity (Note 1) RW(n)(actual) - RW(n)(expected) Relative Linearity (Note 2) RW(n+1) - (RW(n)+MI) 40 -120 dBV 3 % ±1 MI (Note 3) ±0.2 MI (Note 3) RTOTAL Temperature Coefficient (Note 5) ±300 ppm/°C Ratiometric Temperature Coefficient (Note 5) ±20 ppm/°C 10/10/25 pF Potentiometer Capacitances See Circuit #3 NOTES: 1. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage = (VW(n)(actual) - VW(n)(expected)) = ±1 MI maximum. 2. Relative linearity is a measure of the error in step size between taps = RW(n+1) - (RW(n) + MI) = ±0.2 MI. 3. 1 MI = minimum increment = RTOT/31. FN8177 Rev 7.00 October 7, 2015 Page 5 of 12 X9313 DC Electrical Specifications Over recommended operating conditions, unless otherwise stated. LIMITS SYMBOL PARAMETER TEST CONDITIONS/NOTES VCC Active Current CS = VIL, U/D = VIL or VIH and INC = 0.42/2.4V @ max tCYC Standby Supply Current CS = VCC - 0.3V, U/D and INC = VSS or VCC - 0.3V ILI CS, INC, U/D Input Leakage Current VIN = VSS to VCC VIH CS, INC, U/D Input HIGH Current VIL CS, INC, U/D Input LOW Current CIN (Note 5) CS, INC, U/D Input Capacitance ISB MIN TYP (Note 4) MAX UNIT 1 3 mA 200 500 µA ±10 µA 2 V +0.8 VCC = 5V, VIN = VSS, TA = +25°C, f = 1MHz V 10 pF Endurance and Data Retention PARAMETER MIN UNIT Minimum endurance 100,000 Data changes per bit per register Data retention 100 Years VH/RH VH/RH RTOTAL TEST POINT RH CW CH VS TEST POINT VW/RW VL/RL FIGURE 1. TEST CIRCUIT #1 FN8177 Rev 7.00 October 7, 2015 VL/RL VW/RW VW FORCE CURRENT FIGURE 2. TEST CIRCUIT #2 CL RL 10pF 25pF 10pF RW FIGURE 3. CIRCUIT #3 SPICE MACRO MODEL Page 6 of 12 X9313 AC Electrical Specifications Over recommended operating conditions, unless otherwise stated. LIMITS SYMBOL PARAMETER TYP (Note 4) MIN MAX UNIT tCI CS to INC Setup 100 ns tID INC HIGH to U/D Change 100 ns tDI U/D to INC Setup 2.9 µs tIL INC LOW Period 1 µs tIH INC HIGH Period 1 µs tIC INC Inactive to CS Inactive 1 µs tCPH CS Deselect Time (STORE) 20 ms tCPH CS Deselect Time (NO STORE) 100 ns INC to VW Change tIW tCYC 5 INC Cycle Time tR, tF (Note 5) tPU (Note 5) 2 µs INC Input Rise and Fall Time 500 Power-up to Wiper Stable tR VCC (Note 5) tWR (Note 5) µs 10 VCC Power-up Rate µs 0.2 50 Store Cycle µs V/ms 10 ms NOTES: 4. Typical values are for TA = +25°C and nominal supply voltage. 5. This parameter is not 100% tested. 1ms after VCC reaches its final value. The VCC ramp specification is always in effect. In order to prevent unwanted tap position changes, or an inadvertent store, bring the CS and INC high before or concurrently with the VCC pin on power-up. Power-Up and Power-Down Requirements The recommended power-up sequence is to apply VCC/VSS first, then the potentiometer voltages. During power-up, the data sheet parameters for the DCP do not fully apply until CS tCYC tCI tIL tIH tCPH tIC 90% INC 90% 10% tID tDI tF tR U/D tIW MI (SEE NOTE) VW NOTE: MI IN THE AC TIMING DIAGRAM REFERS TO THE MINIMUM INCREMENTAL CHANGE IN THE VW OUTPUT DUE TO A CHANGE IN THE WIPER POSITION. FIGURE 4. AC TIMING DIAGRAM FN8177 Rev 7.00 October 7, 2015 Page 7 of 12 X9313 Applications Information Electronic digitally controlled potentiometers (XDCP) provide three powerful application advantages: 1. The variability and reliability of a solid-state potentiometer. 2. The flexibility of computer-based digital controls. 3. The retentivity of nonvolatile memory used for the storage of multiple potentiometer settings or data. Basic Configurations of Electronic Potentiometers VR VR VH VW/RW VL I THREE-TERMINAL POTENTIOMETER; VARIABLE VOLTAGE DIVIDER TWO-TERMINAL VARIABLE RESISTOR; VARIABLE CURRENT Basic Circuits BUFFERED REFERENCE VOLTAGE CASCADING TECHNIQUES R1 +V NONINVERTING AMPLIFIER +5V +V VS +V +5V VW VREF X VW/RW VOUT – VO – OP-07 + LM308A + -5V R2 +V -5V R1 VW VOUT = VW/RW (a) (b) VO = (1 + R2/R1)VS VOLTAGE REGULATOR R1 VIN VO (REG) 317 COMPARATOR WITH HYSTERESIS OFFSET VOLTAGE ADJUSTMENT R2 VS VS LT311A – VO + 10k +12V 10k } 10k R2 } TL072 Iadj VO (REG) = 1.25V (1 + R2/R1) + IADJ R2 VO + 100k R1 – R1 R2 VUL = [R1/(R1 + R2)] VO(max) VLL = [R1/(R1 + R2)] VO(min) -12V (FOR ADDITIONAL CIRCUITS SEE AN115) FN8177 Rev 7.00 October 7, 2015 Page 8 of 12 X9313 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION October 7, 2015 FN8177.7 CHANGE Added Revision History beginning with Rev 7. Added About Intersil Verbiage. Updated Ordering Information on page 2. DC Electrical Spec Table on page 6 - changed ICC for Parameter VCC Active Current to ISB Updated POD M8.118 to most current revision with changes as follows: Corrected lead width dimension in side view 1 from "0.25 - 0.036" to "0.25 - 0.36" Updated to new intersil format by adding land pattern and moving dimensions from table onto drawing. Updated POD M8.15 to most current revision with changes as follows: Changed Note 1 "1982" to "1994" Changed in Typical Recommended Land Pattern the following: 2.41(0.095) to 2.20(0.087) 0.76 (0.030) to 0.60(0.023) 0.200 to 5.20(0.205) Updated to new POD format by removing table and moving dimensions onto drawing and adding land pattern. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support FN8177 Rev 7.00 October 7, 2015 Page 9 of 12 X9313 Package Outline Drawing M8.118 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE Rev 4, 7/11 5 3.0±0.05 A DETAIL "X" D 8 1.10 MAX SIDE VIEW 2 0.09 - 0.20 4.9±0.15 3.0±0.05 5 0.95 REF PIN# 1 ID 1 2 B 0.65 BSC GAUGE PLANE TOP VIEW 0.55 ± 0.15 0.25 3°±3° 0.85±010 H DETAIL "X" C SEATING PLANE 0.25 - 0.36 0.08 M C A-B D 0.10 ± 0.05 0.10 C SIDE VIEW 1 (5.80) NOTES: (4.40) (3.00) 1. Dimensions are in millimeters. (0.65) (0.40) (1.40) TYPICAL RECOMMENDED LAND PATTERN FN8177 Rev 7.00 October 7, 2015 2. Dimensioning and tolerancing conform to JEDEC MO-187-AA and AMSEY14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.15mm max per side are not included. 5. Dimensions are measured at Datum Plane "H". 6. Dimensions in ( ) are for reference only. Page 10 of 12 X9313 Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, 1/12 DETAIL "A" 1.27 (0.050) 0.40 (0.016) INDEX 6.20 (0.244) 5.80 (0.228) AREA 0.50 (0.20) x 45° 0.25 (0.01) 4.00 (0.157) 3.80 (0.150) 1 2 8° 0° 3 0.25 (0.010) 0.19 (0.008) SIDE VIEW “B” TOP VIEW 2.20 (0.087) SEATING PLANE 5.00 (0.197) 4.80 (0.189) 1.75 (0.069) 1.35 (0.053) 1 8 2 7 0.60 (0.023) 1.27 (0.050) 3 6 4 5 -C- 1.27 (0.050) 0.51(0.020) 0.33(0.013) SIDE VIEW “A 0.25(0.010) 0.10(0.004) 5.20(0.205) TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensioning and tolerancing per ANSI Y14.5M-1994. 2. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only. 6. The lead width as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS-012-AA ISSUE C. FN8177 Rev 7.00 October 7, 2015 Page 11 of 12 X9313 Plastic Dual-In-Line Packages (PDIP) E D A2 SEATING PLANE L N A PIN #1 INDEX E1 c e b A1 NOTE 5 1 eA eB 2 N/2 b2 MDP0031 PLASTIC DUAL-IN-LINE PACKAGE INCHES SYMBOL PDIP8 PDIP14 PDIP16 PDIP18 PDIP20 TOLERANCE A 0.210 0.210 0.210 0.210 0.210 MAX A1 0.015 0.015 0.015 0.015 0.015 MIN A2 0.130 0.130 0.130 0.130 0.130 ±0.005 b 0.018 0.018 0.018 0.018 0.018 ±0.002 b2 0.060 0.060 0.060 0.060 0.060 +0.010/-0.015 c 0.010 0.010 0.010 0.010 0.010 +0.004/-0.002 D 0.375 0.750 0.750 0.890 1.020 ±0.010 E 0.310 0.310 0.310 0.310 0.310 +0.015/-0.010 E1 0.250 0.250 0.250 0.250 0.250 ±0.005 e 0.100 0.100 0.100 0.100 0.100 Basic eA 0.300 0.300 0.300 0.300 0.300 Basic eB 0.345 0.345 0.345 0.345 0.345 ±0.025 L 0.125 0.125 0.125 0.125 0.125 ±0.010 N 8 14 16 18 20 Reference NOTES 1 2 Rev. C 2/07 NOTES: 1. Plastic or metal protrusions of 0.010” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions E and eA are measured with the leads constrained perpendicular to the seating plane. 4. Dimension eB is measured with the lead tips unconstrained. 5. 8 and 16 lead packages have half end-leads as shown. © Copyright Intersil Americas LLC 2005-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN8177 Rev 7.00 October 7, 2015 Page 12 of 12
X9313WSIZT1 价格&库存

很抱歉,暂时无法提供与“X9313WSIZT1”相匹配的价格&库存,您可以联系我们找货

免费人工找货
X9313WSIZT1
  •  国内价格
  • 1+54.97200
  • 10+48.22200
  • 30+44.10720

库存:4