AP2301

MMIC `Product Features AP2301 (Old part#: AP230S12) Application • Satellite • Converter • CATV • Optical node • Small size • SMD Type Package • NO matching circuit needed • High efficiency • Dual supply voltage • Higher linearity • 12 pin Air cavity package • Higher productivity • Lower manufacturing cost • GaAs MMIC • 3 – 2000MHz • -63dBc CSO 135 Channels@ output Level +37dBmV • -60dBc CTB 135 Channels@ output Level +37dBmV Package : SP12 Description The power amplifier is designed for base stations and repeater systems. GaAs MMIC is used and attached on a copper carrier of 12 pin air cavity package with dual supply voltage. *The data in this spec sheet is valid only for 75 ohm application. 50 ohm data is in a separate spec sheet. Operating Ranges PARAMETER Device Voltage Case Temperature PARAMETER Device Voltage Device Current RF Input Power Storage Temperature UNIT VDC ℃ UNIT VDC mA dBm ℃ U nits M Hz V mA dB dB dB dB dB dBm dBm dB dB dBm dBm dB dBc dBc dBc dBc dBc dBc 200 MIN -40 MIN TYP +5 - MAX +5.3 +85 MAX +5.5 +320 +10 Absolute Minimum and Maximum Ratings -40 Typical 3M Hz~2.0GHz 5 +150 T=25℃, Vcc=5.0V, 75Ω system Condition Vcc=5V Specifications Parameter Frequency Range Supply Voltage Single Ended CATV Evaluation Circuit Current S21-Gain S21-Gain S21-Gain S11-Input Return Loss S22-Output Return Loss Noise Figure OIP3 OIP1 S11-Input Return Loss S22-Output Return Loss OIP3 OIP1 Noise Figure CSO 50 - 870M Hz CTB XM D CSO 3 - 150M Hz CTB XM D M inimum M aximum 220 16 14.5 15 14.5 15 Reverse ( 3 ~ 200M Hz ) -16 -16 5.5 41 43 20 22 Forward ( 50 ~ 870M Hz ) -11 -11 36 38 20 22 4 -63 -60 -60 -70 -73 -70 250 3M Hz 50M Hz 2000M Hz -13 -13 +10dBm/2 tone separated by 1M Hz At 100M Hz -8 -8 +10dBm/2 tone separated by 1M Hz At 800M Hz 6 -55 -60 -55 135 channels,+37dBmV/ch,Single 135 channels,+37dBmV/ch,Single 135 channels,+37dBmV/ch,Single 8 channels,+45dBmV/ch,Single 8 channels,+45dBmV/ch,Single 8 channels,+45dBmV/ch,Single ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 2.0 MMIC AP2301 (Old part#: AP230S12) Application Circuit: 3MHz ~ 200MHz 30 20 S-Parameters S21 8 Noise Figure 7 10 0 -10 -20 -30 Noise Figure(dB) 180 210 240 270 300 Magnitude(dB) 6 5 S22 S11 0 5 4 3 30 60 90 120 150 Frequency(MHz) 5 50 100 150 200 250 Frequency(MHz) 25 20 15 10 5 0 5 50 P1dB OIP3(dBm) 50 45 40 35 30 25 20 15 OIP3 dBm 100 150 200 250 5 50 100 150 200 250 Frequency(MHz) Level: +45dBmV FRQ 7 31 49 XMD(NCTA) 72.2 72.8 72.1 Tilt: 8CH FLAT CTB_RAW 79.9 78.6 79.8 CTB_COR 80.1 78.8 80.1 N-FLR 93.6 92.1 91.8 CSU_RAW 92.4 78.1 78.2 CSU_COR 96.7 78.4 78.4 CSU_FRQ 7.63 32 49.99 Frequency(MHz) CSL_RAW 71.7 76.6 90.5 CSL_COR 71.7 76.8 94.8 CSL_FRQ 5.99 29.99 48.31 ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 2.0 MMIC AP2301 (Old part#: AP230S12) Application Circuit: 30MHz ~ 2000MHz Performance Charts (Vdc=5V, Id=220mA, Tc=25℃) S -parameter Vs. Frequency 20 10 17 6 Noise Figure Vs. Frequency Return Loss(dB) Noise Figure(dB) 15 5 4 3 2 1 0 30 200 400 600 800 1000 1200 1400 1600 1800 2000 -10 -20 -30 -40 0 200 400 600 800 1000 1200 1400 1600 1800 11 9 7 5 2000 Gain(dB) 0 13 Freq(MHz ) S11 S22 Gain(dB) Freq(MHz ) NF(dB) OIP3 V s. Frequency 45 41 P1dB V s. Frequency 30 25 OIP3(dBm ) 37 33 29 25 21 30 200 400 600 800 1000 1200 1400 1600 1800 2000 P1dB(dBm) 20 15 10 5 0 30 200 400 600 800 1000 1200 1400 1600 1800 2000 Freq(MHz ) OIP3(dBm) Freq(MHz ) P1dB ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 2.0 MMIC AP2301 (Old part#: AP230S12) Multi-Tone Test 135ch@+30dBmV (Vcc +5V) Level: +30dBm FRQ 55.25 77.25 109.25 211.25 331.25 445.25 547.25 637.25 745.25 859.25 Tilt: FLAT_CH135 CTB_RAW 75.5 76.1 76.1 76.1 74.9 75.6 74.3 74.5 73.9 72.6 CTB_COR 79.8 80.4 80.4 80.4 79.2 79.9 78.7 78.8 78.3 76.9 N-FLR 76.9 77.1 77.6 77.7 76.3 77 75.3 75.8 75.2 73.6 CSU_RAW 76.6 76.1 77.5 77.4 76 76.7 74.9 75 74.2 72.6 CSU_COR 80.9 80.4 81.8 81.8 80.4 81.1 79.2 79.3 78.6 77 CSU_FRQ 55.93 77.99 109.96 212.31 331.88 446.48 548.42 638.49 746.48 860.48 CSL_RAW 76 76.9 77.1 77.1 75.9 76.6 74.9 75.4 74.8 73.2 CSL_COR 80.3 81.2 81.4 81.4 80.2 81 79.2 79.7 79.2 77.5 CSL_FRQ 54 76.25 107.99 209.99 329.98 443.98 545.99 635.99 743.92 858.49 XMD(NCTA) 74.2 75 74.9 74.8 75.7 76.3 77.7 77.4 77.4 77.8 Min Max 74.2 77.8 72.6 76.1 76.9 80.4 73.6 77.7 72.6 77.5 77 81.8 55.93 860.48 73.2 77.1 77.5 81.4 54 858.49 Multi-Tone Test 135ch@+37dBmV (Vcc +5V) Level: +37dBmV FRQ 55.25 77.25 109.25 211.25 331.25 445.25 547.25 637.25 745.25 859.25 Tilt: 135CH FLAT CTB_RAW 66.7 68.3 66.4 66.9 65.7 66.2 66.3 66.1 66.6 67 CTB_COR 66.9 68.4 66.4 67 65.7 66.3 66.4 66.3 66.8 67.2 N-FLR 82.9 83.2 84.1 83.6 82.5 82.9 81.4 81.6 81.5 79.7 CSU_RAW 80.2 68.5 80.3 76.1 73.3 73.2 72.4 73.2 73.9 74.4 CSU_COR 83.2 68.7 82.9 77 73.9 73.7 73 73.9 74.7 76.1 CSU_FRQ 55.99 78 110 212.5 332.5 446.49 548.5 638.49 746.5 860.49 CSL_RAW 67.4 82.9 70.4 71.5 72.3 73.8 74.1 75.9 78.1 78.8 CSL_COR 67.5 87.2 70.6 71.8 72.8 74.4 75.1 77.2 80.6 83.1 CSL_FRQ 53.99 76.22 108 209.99 329.99 443.99 545.99 635.98 743.99 858.49 XMD(NCTA) 60.4 60.9 61 60.4 61.6 61.5 62.7 62.5 62.8 63.3 Min Max 60.4 63.3 65.7 68.3 65.7 68.4 79.7 84.1 68.5 80.3 68.7 83.2 55.99 860.49 67.4 82.9 67.5 87.2 53.99 858.49 ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 2.0 MMIC ESD PROTECTION AP2301 (Old part#: AP230S12) For a safe use in all situations, it is recommended to have proper ESD control techniques while the device is being handled. Here are some recommended precautions; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench Dimension : PMBG-SQFP-12 Block Diagram 4 Outline Drawing 4 AMP2 7 E ( SQ.) C D 7 3 3 AMP1 1 1 10 12 10 F B 12 (SQ.) (SQ.) Function Input Output , Bias Ground Pin No. 7, 9 1, 3 2,4, 5, 6,8, 10, 11, 12 Backside Copper F INCH 0.282 0.2 0.246 No. MM 7.16 5.08 6.25 1.75 0.38 0.76 0.51 1.02 0.36 2.1 0.8 A A B C D E F G H J K M Land Pattern 1.02 4 0.069 0.015 0.03 3 0.2 0.4 0.14 0.83 G 1 H J K (SQ.) M 0.32 RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 2.0