RFC1G22-24

Wideband Amplifier Product Features • GaAs MMIC • Very Low Distortion • Guaranteed Broadband Power Gain • Heat Sink 99.9% Copper, Ag or Gold Plate • Excellent Thermal Conductivity • Single Supply Voltage @ 24V • Low DC Power Consumption • No External Circuit needed RFC1G22-24 Application • Drive Amplifier Description The RFC1G22-24 is specifically designed for up to 1GHz in frequency as amplifiers. This hybrid dynamic range amplifier module operates with a single voltage supply of 24V(DC). The RFC1G22-24 is equipped with over-voltage suppressor. Specifications Absolute Maximum Ratings PARAMETER VDD / VRFOUT RFIN (Single Tone) Storage Temperature Operating Temperature MIN -40 -20 MAX 28 +15 +100 +100 UNITS VDC dBm ℃ ℃ Electrical Specifications (TA = +25℃, VDD = 24V) RFC 1G22-24 PARAMETER MIN Bandwidth (MHz) Gain @1000MHz (dB) Gain Flatness @ 20-1000MHz (dB) Input / Output VSWR IP3 (dBm)@ 20-1000MHz Power Output 1dB Comp. @ 20- 1000MHz (dBm) IMD3 (dBc) Two Tone 20dBm Output @ 20-1000MHz Noise Figure (dB) @ 20-1000MHz Supply Current (mA) 20 21.0 2.5 : 1 48.0 29.0 56.0 380 TYP 22.0 1.5 2.0 : 1 50.0 30.0 60.0 3.5 400 MAX 1000 2.0 - 5.0 430 ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 5.5 Wideband Amplifier Typical RF Performance at 25℃ Parameter Frequency S21 - Gain S11 – Input Return Loss S22 – Output Return Loss OIP1 OIP3 Noise Figure Supply Voltage Current Units MHz dB dB dB dBm dBm dB V mA 20 21 -14 -16 29 48.5 3.6 Typical 500 22 -30 -16 30 51 3.5 24 380 ~ 430 1000 22 -15 -17 29 49 4.8 RFC1G22-24 S-Parameters 30 20 10 0 S21 36 34 32 30 Power Output 1dB Compression Magnitude(dB) -10 dBm S11 1000 1200 1400 1600 1800 2000 S22 -20 -30 -40 -50 -60 -70 20 200 400 600 800 28 26 6 24 22 20 4 5 20 100 200 300 400 500 600 700 800 900 1000 Frequency(MHz) Frequency(MHz) Noise Figure(dB) 3 Noise Figure 6 OIP 3 54 2 5 52 Noise Figure(dB) 4 50 1 OIP3(dBm) 48 0 20 100 200 300 400 500 600 700 800 900 1000 3 46 2 44 1 42 0 20 100 200 300 400 500 600 700 800 900 1000 40 20 100 200 300 400 500 600 700 800 900 1000 Frequency(MHz) Frequency(MHz) ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 5.5 Wideband Amplifier ESD PROTECTION RFC1G22-24 Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. Some of the precautions recommended are; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench. NOTES FOR CORRECT USE 1. 2. On the power input port (Pin#5), 47uF/35V capacitor GND is recommended. The heat sink of CATV Hybrids is to be mounted in direct contact with the metal case of the equipment. Heat conducting grease should be applied to the module/equipment interface and the unit tightly secured. Put the power off before adjusting in/output matching of the system. The unit must have a common ground with the equipment and the analyzer. Pay close attention to the input voltage not to over power the hybrid. The space between bottom of socket and the tip of the lead is recommended to have space of 2mm+ to protect the pin Do not open the plastic cover to change the matching inside the hybrid. Once opened, RFHIC will not be responsible for the hybrid. 3. 4. 5. 6. 7. Package Dimensions (Type: DP-27) Pin No. 1 2,3,7,8 5 9 Function RF Input Ground Vcc RF Output RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5011 ▪ rfsales@rfhic.com ▪ All specifications may change without notice. ▪ Version 5.5