RWP05020-1H

Wideband Power Amplifier Product Features 0B 1B RWP05020-10 Application HF/VHF/UHF GaN on SiC Broadband High Power Amplifier 20 to 1000MHz Operation Bandwidth Small Signal Gain 38dB min 20W Typical. P3dB Package : DP-75 Description 2B The power amplifier module is designed for Broadcasting, Telecommunication, Medical and Other markets. Operating frequency range is from 20MHz to 1000MHz. Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband performance is already applied. Improved thermal handling by patented technology. Typical Specifications No 1 2 3 4 5 Bandwidth Small Signal Gain Gain Variation vs Temperature Gain Variation vs Frequency P3dB 20MHz to 400MHz 400 MHz to 1000MHz 20MHz to 400 MHz 400 MHz to 700 MHz 700 MHz to 1000 MHz 7 8 9 10 11 12 13 Input Return Loss Output Return Loss 2nd Harmonic suppression Supply Voltage Quiescent Current consumption Current Consumption @ P3dB On/Off Switching Time Shut Down or Switch On/Off TTL Voltage CW 1-tone On : TTL "Low" CW 1-tone -20°C to 60°C Item Conditions VCC = +28V; T = 25℃; ZS = ZL = 50Ω Min 20 38 -2 ±1 42 41 50 47 45 44 43 53 50 47 -15 -10 -35 27.5 1.7 28 1.9 2.3 3 0 2.5 5 -10 -7 -30 30 2.1 3 5 0.5 5.5 dB dB dBc V A A uS dBm 40 Typ Max 1000 42 +2 ±1.5 Unit MHz dB dB dBpp dBm 6 OIP3 @ Po = +33dBm (1MHz Tone spacing, CW 2-Tone) @Po = +30dBm, Freq 500MHz Vcc(=Vds) Off : TTL "High"(300mA@Disable) On : TTL “Low”(Enable) Off : TTL “High” V 14 ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 2.1 Wideband Power Amplifier Environmental Characteristics No 1 2 3 Operating Temperature Storage Temperature Vibration Item RWP05020-10 Min -20 -40 Typ Max +60 +105 Unit °C °C MIL-STD-810G Method 514.6 ANNEX C Absolute Maximum Ratings No 1 2 3 4 Input RF Power Supply Voltage Load Mismatch Value Item Operating Flange Temperature Rating +85 +10 +30 3 : 1 @ all load phase Unit °C dBm V * Input Signal Condition : CW 1-Tone Ordering Information No 1 2 RWP05020-10 RWP05020-1H Part Number Pallet Module assembled with RWP05020-10 Package * RWP05020-1H is a SMA connectorized housing version of RWP05020-10. Electrical parameters are all same as RWP05020-10. For more information, please contact RFHIC ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 2.1 Wideband Power Amplifier RWP05020-10 Typical Performance @ 25℃ 4B RWP05020-10 Frequency (MHz) 20 100 200 300 400 500 600 700 800 900 1000 P1dB (dBm) 42.4 42.5 43.3 44.2 44.6 43.7 43.9 43.4 42.8 42.0 41.7 P3dB (dBm) 44.3 44.5 44.8 45.4 45.6 45.3 44.9 44.5 44.2 43.7 44.1 Current@P1dB (A) 1.9 2.0 2.1 2.1 2.1 2.0 2.0 1.9 1.8 1.8 2.0 Current@P3dB (A) 2.2 2.2 2.3 2.3 2.3 2.3 2.2 2.1 1.9 2.0 2.3 2nd Harm @30dBm(dBc) -43.4 -42.5 -39.9 -35.8 -33.4 -34.9 -47.1 -42.5 -47.3 -55.1 -54.1 OIP3 (30dBm/Tone) (dBm) 54.4 54.9 55.1 54.6 53.6 52.2 51.4 49.4 48.3 47.5 47.1 P3dB 48.0 47.0 46.0 45.0 MAG (dBm) MAG(dBc) -10.0 -15.0 -20.0 -25.0 -30.0 -35.0 -40.0 -45.0 -50.0 -55.0 -60.0 z z z 2nd Harmonics 44.0 43.0 42.0 41.0 40.0 39.0 38.0 z z z z z z z 60 0M H 10 0M H 20 0M H 30 0M H 70 0M H 80 0M H z 10 00 M H z 20 M H 20 0M H 10 0M H 70 0M H 50 0M H 60 0M H 80 0M H 30 0M H 40 0M H 90 0M H Frequency (MHz) Frequency (MHz) IM3 @ 20MHz -20 -25 -30 -35 IM3 @ 500MHz -20 -25 -30 -35 MAG(dBc) MAG(dBc) -40 -45 -50 -55 -60 -65 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 -40 -45 -50 -55 -60 -65 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Output Power (dBm) Output Power (dBm) ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 2.1 10 00 M H 90 0M H 50 0M H 40 0M H 20 M H z z z z z z z z z z Wideband Power Amplifier IM3 @ 1000MHz -10 -15 -20 -25 -30 RWP05020-10 Gain 45 40 MAG(dBc) -35 -40 -45 -50 -55 -60 - 65 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 MAG(dB) 35 30 25 10 250 500 750 1000 FREQ(MHz) 1250 1500 1750 2000 Output Power (dBm) Input Return Loss 0 Output Return Loss 0 -5 -5 -10 -10 MAG(dB) MAG(dB) -15 -15 -20 -20 -25 -25 - 30 10 250 500 750 1000 FREQ(MHz) 1250 1500 1750 2000 - 30 10 250 500 750 1000 FREQ(MHz) 1250 1500 1750 2000 Precautions 3B 1. This product is designed to be used for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is no RF signal, and the amplifier is “on” with current draw. Vcc(+28V) RF IN RF OUT Temp Monitor The temperature must be calculated properly. Case temperature must maintain below 85°C. Right side drawing notes how to use a temperature monitoring Shut Down (+5V) Switch ON/OFF +Vcc function to protect against overheating. 2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device. Comparator Block (with hysteresis gap) + Ref Voltage ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 2.1 Wideband Power Amplifier Package Dimensions (Type: DP-75) (Unit : mm/[inch], Tolerance : ±0.2/[.008]) RWP05020-10 How to connect the amplifier to a target PCB Method-І (with Pin) Method-ΙІ (without Pin) - If you cut out the pin Pin Description Pin No 1 2 3 4 5 6 RF IN Vcc (+28V) Shut Down (+5V) Switch ON/OFF Temp Monitor RF OUT U U U Port Name RF Input DC Supply Function Shut Down @ TTL High, Enable @ TTL Low Disable @ TTL High (Switch Status : Off) 0.85V @ 25℃, Scale : 10mV/℃ (Accuracy : ±3℃) RF Output U * Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket) * Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 2.1 Wideband Power Amplifier Note : RWP05020-10 RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 2.1