RWP15020-G1

Wideband Power Amplifier Product Features GaN on SiC Broadband High Power Amplifier 1000 to 2000MHz Operation Bandwidth Small Signal Gain 27dB min 20W Typical. P3dB RWP15020-G1 UHF/Military Application Description Package : DP-75 The power amplifier module is designed for Broadcasting, Telecommunication, Medical, Military and Other markets. Operating frequency range is from 1000MHz to 2000MHz. Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband performance is already applied. Improved thermal handling by patented technology. Typical Specifications No 1 2 3 4 5 Bandwidth Small Signal Gain Gain Variation vs Temperature Gain Variation vs Frequency P3dB OIP3 @ Po = +33dBm (1MHz Tone spacing, CW 2-Tone) Input Return Loss Output Return Loss 2nd Harmonic suppression Supply Voltage Quiescent Current consumption Current Consumption @ P3dB On/Off Switching Time Shut Down or Switch On/Off TTL Voltage CW 1-tone On : TTL "Low" Off : TTL "High"(300mA@Disable) On : TTL “Low”(Enable) Off : TTL “High” CW 1-tone @Po = +30dBm, Freq 1000MHz Vcc(=Vds) 1000MHz to 1200MHz 1200MHz to 2000MHz 1000MHz to 1600MHz 1600MHz to 2000MHz -20°C to 60°C Item Conditions VCC = +28V; T = 25℃; ZS = ZL = 50Ω Min 1000 27 -2 ±1 41 42 48 46 43 44 50 48 -10 -10 -35 27.5 28 2.2 -6 -5 -28 30 2.5 3.6 3 0 2.5 5 5 0.5 5.5 dB dB dBc V A A uS dBm 29 Typ Max 2000 31 +2 ±2 Unit MHz dB dB dBpp dBm 6 7 8 9 10 11 12 13 14 V ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier Environmental Characteristics No 1 2 3 Operating Temperature Storage Temperature Vibration Item RWP15020-G1 Min -20 -40 Typ Max +60 +105 Unit °C °C MIL-STD-810G Method 514.6 ANNEX C Absolute Maximum Ratings No 1 2 3 4 Input RF Power Supply Voltage Load Mismatch Value Item Operating Flange Temperature Rating +85 +20 +30 3 : 1 @ all load phase Unit °C dBm V * Input Signal Condition : CW 1-Tone Ordering Information No 1 2 RWP15020-G1 RWP15020-GH Part Number Pallet Module assembled with RWP15020-G1 Package * RWP15020-GH is a SMA connectorized housing version of RWP15020-G1. Electrical parameters are all same as RWP15020-G1. For more information, please contact RFHIC. ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier RWP15020-G1 Typical Performance @ 25℃ Frequency (MHz) 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 P1dB (dBm) 39.4 39.8 40.6 41.5 42.1 42.3 43.0 43.2 42.6 42.4 42.0 P3dB (dBm) 42.5 42.9 43.8 44.5 44.5 45.2 45.4 45.4 44.8 44.3 43.9 Current@P1dB (A) 2.3 2.4 2.1 2.5 2.5 2.5 2.4 2.3 2.1 2.0 2.0 RWP15020-G1 Current@P3dB (A) 2.9 3.1 3.3 3.3 3.3 3.2 3.0 2.7 2.5 2.3 2.3 2nd Harm @30dBm(dBc) -34.7 -43.5 -49.4 -47.7 -43.3 -41.8 -43.8 -46.1 -49.6 -52.7 -61.3 OIP3 (30dBm/Tone) (dBm) 49.5 49.8 50.4 50.8 51.0 51.1 51.0 50.3 49.5 48.5 47.6 P3dB 2nd Harmonics OIP3 Power Gain @ Pin=18dBm ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier Precautions RWP15020-G1 1. This product is designed to be used for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is no RF signal, and the amplifier is “on” with current draw. The temperature must be calculated properly. Case temperature must maintain below 85°C. 2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device. Package Dimensions (Type: DP-75) (Unit : mm/[inch], Tolerance : ±0.2/[.008]) 70 [2.756] 60 [2.362] 20 [.787] 20 [.787] 70 [2.756] 60 [2.362] 38 [1.496] 50.8 [2] 45 [1.772] 1.5 [.059] 15.6 [.616] 6.2 [.245] 6.9 [.273] 7.3 [.288] 7.3 [.286] 6.9 [.273] 38 [1.496] 50.8 [2] 'A' C 1 [.039] 3.8 [.15] 5 [.197] 4 [.156] 2.5 [.098] 17.1 [.673] 4.1 [.161] 4.5 [.177] 2 [.079] 1.5 [.059] How to connect the amplifier to a target PCB Method-І (with Pin) Method-ΙІ (without Pin) - If you cut out the pin ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier Pin Description Pin No 1 2 3 4 5 6 RF IN Vcc (+28V) Shut Down (+5V) Switch ON/OFF GND RF OUT Port Name RWP15020-G1 Function RF Input DC Supply Shut Down @ TTL High, Enable @ TTL Low Disable @ TTL High (Switch Status : Off) Ground RF Output * Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket) * Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt Note : RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1