HO4006

Preliminary HO4006 • • • SAW Frequency Stabilization Fundamental-Mode Oscillation at 640.0 MHz A Rugged, Compact General-Purpose Oscillator The frequency of this oscillator is stabilized by surface-acoustic-wave (SAW) technology. This results in excellent performance from a compact, rugged, oscillator operating at the fundamental frequency of 640.0 MHz. The highly-reliable HO4006 makes it suitable for general purpose use in a wide variety of applications 640.0 MHz SAW Oscillator Dip 16-8 Case Electrical Characteristics Characteristic Operating Frequency Absolute Frequency Tune Range Tune Voltage Tuning Linearity RF Output Power Discrete Spurious Second Harmonics Third and Higher Harmonics Nonharmonic SSB Phase Noise 1 kHz Offset 10 kHz Offset RF Impedance DC Power Supply 100kHz Offset Nominal Impedance Operating Load VSWR Operating Voltage Operating Current Operating Ambient Temperature Lid Symbolization (YY=Year, WW=Week) ZO GL VCC ICC TA 3, 6 -20 RFM HO4006 YYWW 2, 3, 4 2, 3, 4 -80 -115 -135 -160 50 4.75 2:1 5.25 45 +70 -105 -130 dBc/Hz Ω VDC mA °C PO 3, 6 +7 Sym fO 1, 7 639.900 0 2:1 +10 -15 -20 dBc Notes Minimum Typical 640.0 Maximum 640.100 +5 3:1 dBm Units MHz MHz VDC 3 3, 5 3, 6 5.0 35 CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device. Notes: 1. 2. 3. 4. One or more of the following United States patents apply: Unless noted otherwise, all specifications are listed at TA = +25°C ±2°C, VCC = nominal voltage ±0.01 VDC, and load impedance = 50 Ω with VSWR ≤ 1.5:1. The design, manufacturing process , and specification of this device are subject to change without notice. Applies to oscillator only and not to sidebands caused by external electrical or mechanical sources. (Dedicated external voltage regulation with low-frequency filtering for the DC power supply and proper circuit board layout are recommended for optimum spectral purity.) For specified maximum operating load VSWR (any angle) at FO. (No instablity or damage will occur for any passive load impedance.) For any combination of VCC and TA within the specified operating ranges. Applies for any combination of Note 5 and 6 conditions. BLOCK DIAGRAM V CC RF OUTPUT SAW Oscillator Buffer Amplifier ELECTRICAL CONNECTIONS VCC 1 Case Ground 2 V tune 15 Case Ground 5. 6. 7. Top View Case Ground 7 RF Output 8 10 Case Ground 9 V CC RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-9148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com HO4006-101899 Page 1 of 2 640.0 MHz DIP16-8 Voltage Controlled SAW Oscillator Metal Dual-Inline Package with 8 leads in a 16-lead DIP configuration mm Dimension MIN A B C D E F G H K L M N R — — — 0.40 MAX 25.02 12.83 6.35 0.51 MIN — — — 0.016 Inches MAX 0.985 0.505 0.250 0.020 0.64 Nominal 7.62 Nominal 2.54 Nominal 17.78 Nominal 3,39 1.30 — — 1.75 6.73 — 11.18 22.60 2.26 0.025 Nominal 0.300 Nominal 0.100 Nominal 0.700 Nominal 0.130 0.051 — — 0.069 0.265 — 0.440 0.890 0.089 Top View B M C K Bottom View (4 Places) F R (3 Places) 8 7 9 10 L A N 2 1 15 16 H G (4 Places) D Pin 1 Mark (Optional) E (8 Places) RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-9148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com HO4006-101899 Page 2 of 2