RO2216D-6

RO2216D-6 • • • • Ideal for European 905.800 MHz Transmitters Very Low Series Resistance Quartz Stability Complies with Directive 2002/95/EC (RoHS) Pb The RO2216D-6 is a true one-port, surface-acoustic-wave (SAW) resonator in a surface-mount, ceramic case. It provides reliable, fundamental-mode, quartz frequency stabilization of fixed-frequency transmitters operating at 905.800 MHz. This SAW is designed specifically for remote-control and wireless security transmitters operating in Europe under ETSI I-ETS 300 220 and in Germany under FTZ 17 TR 2100. 905.800 MHz SAW Resonator Absolute Maximum Ratings Rating Input Power Level DC voltage Storage Temperature Soldering Temperature (10 seconds / 5 cycles max.) Value 0 12 -40 to +85 260 Units dBm VDC °C °C SM3838-6 Case 3.8 X 3.8 Electrical Characteristics Characteristic Center Frequency (+25 °C) Insertion Loss Quality Factor Temperature Stability Unloaded Q 50 Ω Loaded Q Turnover Temperature Turnover Frequency Frequency Temperature Coefficient Frequency Aging RF Equivalent RLC Model Absolute Value during the First Year Motional Resistance Motional Inductance Motional Capacitance Shunt Static Capacitance Test Fixture Shunt Inductance Lid Symbolization (in addition to Lot and/or Date Codes) Standard Reel Quantity Reel Size 7 Inch Reel Size 13 Inch DC Insulation Resistance between Any Two Terminals RM LM CM CO LTEST 5, 6, 9 2, 7 5, 7, 9 Absolute Frequency Tolerance from 905.800 MHz Sym fC ΔfC IL QU QL TO fO FTC |fA| Notes 2,3,4,5 2,5,6 5,6,7 Minimum 905.700 Typical Maximum 905.900 ±100 Units MHz kHz dB 2.1 7300 1500 10 25 fC 0.032 ≤10 1.0 28 38 0.8 1.8 17 583 // YWWS 500 Pieces/Reel 3000 Pieces/Reel 2.8 40 °C ppm/°C2 ppm/yr MΩ Ω µH fF pF nH 6,7,8 1 5 CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. Frequency aging is the change in fC with time and is specified at +65°C or less. Aging may exceed the specification for prolonged temperatures above +65°C. Typically, aging is greatest the first year after manufacture, decreasing in subsequent years. The center frequency, fC, is measured at the minimum insertion loss point, ILMIN, with the resonator in the 50 Ω test system (VSWR ≤ 1.2:1). The shunt inductance, LTEST, is tuned for parallel resonance with CO at fC. Typically, fOSCILLATOR or fTRANSMITTER is approximately equal to the resonator fC. One or more of the following United States patents apply: 4,454,488 and 4,616,197. Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. Unless noted otherwise, case temperature TC = +25°C±2°C. 6. 7. 8. The design, manufacturing process, and specifications of this device are subject to change without notice. Derived mathematically from one or more of the following directly measured parameters: fC, IL, 3 dB bandwidth, fC versus TC, and CO. Turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fO. The nominal frequency at any case temperature, TC, may be calculated from: f = fO [1 - FTC (TO -TC)2]. Typically oscillator TO is approximately equal to the specified resonator TO. This equivalent RLC model approximates resonator performance near the resonant frequency and is provided for reference only. The capacitance CO is the static (nonmotional) capacitance between the two terminals measured at low frequency (10 MHz) with a capacitance meter. The measurement includes parasitic capacitance with "NC” pads unconnected. Case parasitic capacitance is approximately 0.05 pF. Transducer parallel capacitance can by calculated as: CP ≈ CO - 0.05 pF. 2. 9. 3. 4. 5. www.RFM.com E-mail: info@rfm.com ©2008 by RF Monolithics, Inc. Page 1 of 2 RO2216D-6 - 3/26/08 Electrical Connections The SAW resonator is bidirectional and may be installed with either orientation. The two terminals are interchangeable and unnumbered. The callout NC indicates no internal connection. The NC pads assist with mechanical positioning and stability. External grounding of the NC pads is recommended to help reduce parasitic capacitance in the circuit. Power Test Pin 1 2 3 4 5 6 NC Terminal NC NC Terminal NC Connection P INCIDENT 50 Ω Source at F C P REFLECTED Low-Loss Matching Network to 50 Ω 1 6 2 3 5 4 B 1 6 C G H Typical Application Circuits Typical Low-Power Transmitter Application 1 200k Ω Modulation Input +9VDC C1 L1 47 6 A2 5 E 5 2 I 4 3 4 (Antenna) 3 1 2 3 D J 6 5 4 C2 ROXXXXC Bottom View RF Bypass 470 Case Dimensions Dimension Min A B C D E G H I J 3.60 3.60 1.00 0.95 2.39 0.90 1.90 0.50 1.70 Typical Local Oscillator Application 200k Ω Output mm Nom 3.80 3.80 1.20 1.10 2.54 1.0 2.0 0.6 1.8 Inches Max 4.0 4.0 1.40 1.25 2.69 1.10 2.10 0.70 1.90 +VDC C1 L1 +VDC Min 0.14 0.14 0.04 0.037 0.090 0.035 0.75 0.020 0.067 Nom 0.15 0.15 0.05 0.043 0.10 0.04 0.08 0.024 0.07 Max 0.16 0.16 0.055 0.05 0.110 0.043 0.83 0.028 0.075 1 6 2 3 5 4 C2 ROXXXXC Bottom View RF Bypass Equivalent LC Model 0.05 pF* Typical Test Circuit The test circuit inductor, LTEST, is tuned to resonate with the static capacitance, CO, at FC. Cp Co = Cp + 0.05 pF *Case Parasitics Electrical Test Rm Lm Cm Temperature Characteristics The curve shown on the right accounts for resonator contribution only and does not include LC component temperature contributions. 6 1 fC = f O , T C = T O 0 (f-fo ) / fo (ppm) To 50 Ω Network Analyzer 0 -50 -100 -150 -200 0 +20 +40 +60 +80 From 50 Ω Network Analyzer 5 2 -50 4 3 -100 -150 -200 -80 -60 -40 -20 ΔT = T C - T O ( °C ) www.RFM.com E-mail: info@rfm.com ©2008 by RF Monolithics, Inc. Page 2 of 2 RO2216D-6 - 3/26/08