SF1124A

SF1124A • • • • • Designed for WCDMA 3G IF Applications Excellent Size-to-Performance Ratio Balanced or Unbalanced Input and Output Hermetic 13.3 x 6.5 mm Surface-mount Case Complies with Directive 2002/95/EC (RoHS) Pb Value +10 30 -40 to +85 260°C for 30 s Units dBm VDC °C 190 MHz SAW Filter Absolute Maximum Ratings Rating Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range Suitable for lead-free soldering - Max. Soldering Profile SMP-53 Electrical Characteristics Characteristic Nominal Center Frequency Passband Insertion Loss at fc 1 db Passband 3 db Passband Amplitude Ripple over fc±2.4 MHz Phase Linearity over fc±2.4 MHz Group Delay Variation over fc ±fc2.4 MHz Rejection fc-4.1 to fc-3.65 and fc+3.4 to fc+3.8 MHz fc-5.0 to fc-4.1 and fc+3.8 to fc+5.0 MHz fc-10.0 to fc-5.0 and fc+5.0 to fc+10.0 MHz fc-20.0 to fc-10.0 and fc+10.0 to fc+20.0 MHz At 157.6 MHz At 165.7 MHz fc-60 MHz to fc-20 MHz fc+20 MHz to fc+60 MHz Part to Part Average Group Delay Variation Operating Temperature Range Frequency Temperature Coefficient Impedance Matching to 50Ω Unbalanced Case Style Lid Symbolization (YY = year, WW = week) Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. Sym fC IL BW1 BW3 Notes 1 Min Typ 190.000 12 5.1 5.7 .70 4 75 Max 14.0 Units MHz dB MHz 4.6 1, 2 5.1 1.0 10 120 dBP-P °P-P nsP-P GDV 10 30 40 1, 2, 3 40 40 40 40 40 dB ±5 TA FTC 1 -10 +25 -18 External L-C SMP-53 13.3 x 6.5 mm Nominal Footprint RFM SF1124A YYWW +85 nsec °C ppm/°C Electrical Connections Connection Port 1 Hot Port 1 Gnd Return Port 2 Hot Port 2 Gnd Return Case Ground Terminals 11 12 5 6 All others E-mail: info@rfm.com http://www.rfm.com SF1124A-121504 Page 1 of 3 190.0 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF1124A-121504 Page 2 of 3 190.0 MHz SMP-53 Case SAW Filter 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Case Dimensions Dimension A B C D E H P Min 13.08 6.27 mm Nom 13.31 6.50 1.91 1.50 0.79 1.0 2.54 Max 13.60 6.80 2.00 Min 0.515 0.247 Inches Nom 0.524 0.256 0.075 0.059 0.031 0.039 0.100 Max 0.535 0.268 0.079 Electrical Connections Materials Solder Pad Termination Lid Body Pb Free Au plating 30 - 60 uInches (76.2-152 uM) over 80200 uInches (203-508 uM) Ni. Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Al2O3 Ceramic Port 1 Port 2 Connection Input or Return Return or Input Output or Return Return or Output Ground Single Ended Operation Differential Operation Terminals 11 12 5 6 All others Return is ground Return is hot B 12 11 C H 11 12 D 1 10 10 1 P (8 Places) 2 A 3 9 9 2 8 8 3 E (10 Places) 4 7 7 4 5 6 6 5 TOP VIEW BOTTOM VIEW RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF1124A-121504 Page 3 of 3