RF2317

RF2317 0 RoHS Compliant & Pb-Free Product Typical Applications • CATV Distribution Amplifiers • Cable Modems • Broadband Gain Blocks Product Description The RF2317 is a general purpose, low-cost high-linearity RF amplifier IC. The device is manufactured on an advanced Gallium Arsenide Heterojunction Bipolar Transistor (HBT) process, and has been designed for use as an easily cascadable 75 Ω gain block. The gain flatness of better than ±0.5dB from 50MHz to 1000MHz, and the high linearity, make this part ideal for cable TV applications. Other applications include IF and RF amplification in wireless voice and data communication products operating in frequency bands up to 3GHz. The device is selfcontained with 75 Ω input and output impedances and requires only two external DC biasing elements to operate as specified. -A0.157 0.150 0.008 0.004 0.020 0.014 LINEAR CATV AMPLIFIER • Laser Diode Driver • Return Channel Amplifier • Base Stations 0.020 REF 0.393 0.386 0.034 REF 0.068 0.064 0.244 0.229 8° MAX 0° MIN 0.068 0.053 0.034 0.016 0.009 0.007 Optimum Technology Matching® Applied Si BJT Si Bi-CMOS InGaP/HBT GaAs HBT SiGe HBT GaN HEMT GaAs MESFET Si CMOS SiGe Bi-CMOS Package Style: CJ2BAT0 Features • DC to 3.0GHz Operation • Internally Matched Input and Output NC 1 GND 2 GND 3 RF IN 4 NC 5 GND 6 GND 7 NC 8 16 NC 15 GND 14 GND 13 RF OUT 12 NC 11 GND 10 GND 9 NC • 15dB Small Signal Gain • 4.9dB Noise Figure • +47dBm Output IP3 • Single 9V to 12V Power Supply Ordering Information RF2317 RF2317 PCBA RF2317 PCBA Linear CATV Amplifier Fully Assembled Evaluation Board - 50 Ω Fully Assembled Evaluation Board - 75 Ω Tel (336) 664 1233 Fax (336) 664 0454 http://www.rfmd.com Functional Block Diagram RF Micro Devices, Inc. 7628 Thorndike Road Greensboro, NC 27409, USA Rev A19 050822 3-17 RF2317 Absolute Maximum Ratings Parameter Device Current Input RF Power Output Load VSWR Ambient Operating Temperature Storage Temperature Rating 250 +18 20:1 -40 to +85 -40 to +150 Unit mA dBm °C °C Caution! ESD sensitive device. RF Micro Devices believes the furnished information is correct and accurate at the time of this printing. RoHS marking based on EUDirective2002/95/EC (at time of this printing). However, RF Micro Devices reserves the right to make changes to its products without notice. RF Micro Devices does not assume responsibility for the use of the described product(s). Parameter Overall (50 Ω) Frequency Range Gain Noise Figure Input VSWR Min. DC 13.5 Specification Typ. Max. 3000 15.0 Unit Condition T=+25°C, ICC =180mA, RC =10.2 Ω, 50 Ω System 3dB Bandwidth From 100MHz to 1000MHz Appropriate values for the DC blocking capacitors and bias inductor are required to maintain this VSWR at the intended operating frequency range. Appropriate values for the DC blocking capacitors and bias inductor are required to maintain this VSWR at the intended operating frequency range. At 100MHz At 500MHz At 900MHz F1 =400MHz, F2 =500MHz, FOUT =100MHz At 100MHz At 500MHz At 900MHz 14.3 4.9 1.7:1 MHz dB dB Output VSWR 2.3:1 Output IP3 +37 Output IP2 Output P1dB Reverse Isolation +47 +42 +37 +55 +25.5 +24 +22 19.5 55 150 3100 58 175 380 8.5 9.3 180 dBm dBm dBm dBm dBm dBm dBm dB °C/W °C years °C/W °C years V V mA Thermal ThetaJC Maximum Junction Temperature Mean Time To Failures ThetaJC Maximum Junction Temperature Mean Time To Failures ICC=150mA, PDISS =1.2W, TAMB=85°C TAMB =+85°C ICC=180mA, PDISS =1.5W, TAMB=85°C TAMB =+85°C On pin 13, ICC =150mA On pin 13, ICC =180mA Actual current determined by VCC and RC Power Supply (50 Ω) Device Voltage Operating Current Range 100 200 3-18 Rev A19 050822 RF2317 Parameter Overall (75 Ω) Frequency Range Gain Noise Figure Input VSWR DC 15.0 4.8 1.3:1 3000 MHz dB dB Specification Min. Typ. Max. Unit Condition T=25°C, ICC =180mA, RC =14.3 Ω, 75 Ω System 3dB Bandwidth From 100MHz to 1000MHz Appropriate values for the DC blocking capacitors and bias inductor are required to maintain this VSWR at the intended operating frequency range. Appropriate values for the DC blocking capacitors and bias inductor are required to maintain this VSWR at the intended operating frequency range. At 100MHz At 500MHz At 900MHz F1 =400MHz, F2 =500MHz, FOUT =100MHz At 100MHz At 500MHz At 900MHz 10dBmV per channel, flat, at the input of the amplifier; ICC =150mA, VCC =10.4V At 55.25MHz At 331.25MHz At 547.25MHz At 853.25MHz At 55.25MHz At 331.25MHz At 547.25MHz At 853.25MHz At 55.25MHz At 331.25MHz At 853.25MHz At 547.25MHz At 55.25MHz At 331.25MHz At 547.25MHz At 853.25MHz Output VSWR 1.8:1 Output IP3 +37 Output IP2 Output P1dB Reverse Isolation +49 +43 +38 +58 +22 +22 +21 19 dBm dBm dBm dBm dBm dBm dBm dB 133 Channels XMOD