RF2360411

RF2360Linear General Purpose Amplifier RF2360 LINEAR GENERAL PURPOSE AMPLIFIER RoHS Compliant & Pb-Free Product Package Style: Standard Batwing Features 5 MHz to 1500MHz Operation Internally Matched Input and Output 20dB Small Signal Gain 1.2dB Noise Figure +24dBm Output Power Single 6V to 9V Positive Power Supply NC 1 NC 2 GND 3 GND 4 GND 5 RF IN 6 NC 7 NC 8 16 NC 15 NC 14 RF OUT 13 GND 12 GND 11 NC 10 NC 9 NC Applications CATV Distribution Amplifiers Cable Modems Broadband Gain Blocks Laser Diode Driver Return Channel Amplifier Base Stations Functional Block Diagram Product Description The RF2360 is a general purpose, low-cost, high-linearity RF amplifier IC. The device is manufactured on a Gallium Arsenide process and is featured in an SOP-16 batwing package. It has been designed for use as an easily cascadable 75 Ω gain block with a Noise Figure of less than 2dB. Gain flatness better than 0.5dB from 5MHz to 1000MHz, and high linearity make this part ideal for cable TV applications. Other applications include IF and RF amplification in wireless voice and data communication products operating in frequency bands up to 1000MHz. The device is self-contained with 75 Ω input and output impedances providing less than 2:1 VSWR matching. For higher input and output return losses, see the evaluation schematic. Ordering Information RF2360 RF2360 PCBA RF2360 411 RF2360 412 Linear General Purpose Amplifier Fully Assembled Evaluation Board 50 Ω Fully Assembled Evaluation Board 75H Fully Assembled Evaluation Board 75L Optimum Technology Matching® Applied GaAs HBT GaAs MESFET InGaP HBT SiGe BiCMOS Si BiCMOS SiGe HBT GaAs pHEMT Si CMOS Si BJT GaN HEMT RF MICRO DEVICES®, RFMD®, Optimum Technology Matching®, Enabling Wireless Connectivity™, PowerStar®, POLARIS™ TOTAL RADIO™ and UltimateBlue™ are trademarks of RFMD, LLC. BLUETOOTH is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed for use by RFMD. All other trade names, trademarks and registered trademarks are the property of their respective owners. ©2006, RF Micro Devices, Inc. Rev A12 DS070731 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 1 of 12 RF2360 Absolute Maximum Ratings Parameter Device Current Device Voltage Input RF Power Output Load VSWR Ambient Operating Temperature Storage Temperature Rating 175 9 +13 20:1 -40 to +85 -40 to +150 Unit mA V dBm °C °C Caution! ESD sensitive device. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. RoHS status based on EUDirective2002/95/EC (at time of this document revision). The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents, or other rights of third parties, resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. Parameter Overall (50 Ω) Frequency Range Input VSWR Min. 5 Specification Typ. Max. 1500 Unit MHz 3dB Bandwidth Condition T=25 °C, VDD =7V, 50 Ω System, PIN =-8dBm 1.6:1 Appropriate values for the output DC blocking capacitor and bias inductor are required to maintain this VSWR over the intended operating frequency range. See note for Input VSWR. dB dB dB dB dBm dBm dBm dBm dBm dBm dBm dBm dB dB dB dB dB dBm dBm dBm dBm dBm dBm dBm dBm 9 V At 500MHz 5MHz to 1000MHz At 500MHz From 5MHz to 1000MHz At 10MHz, Delta F1 and F2 = 1MHz At 500MHz At 1000MHz At 100MHz, Delta F1 and F2 = 156MHz At 1000MHz At 10MHz At 500MHz At 1000MHz At 500MHz T=25 °C, VDD =9V, PIN =-8dBm At 500MHz 5MHz to 1000MHz At 500MHz From 5MHz to 1000MHz, At 10MHz, Delta F1 and F2 = 1MHz At 500MHz At 1000MHz At 100MHz, Delta F1 and F2 = 156MHz At 1000MHz At 10MHz At 500MHz At 1000MHz Output VSWR Gain Gain Flatness Noise Figure Noise Figure Output IP3 Output IP3 Output IP3 Output IP2 Output IP2 Output P1dB Output P1dB Output P1dB Reverse Isolation Gain Gain Flatness Noise Figure Noise Figure Output IP3 Output IP3 Output IP3 Output IP2 Output IP2 Output P1dB Output P1dB Output P1dB 1.2:1 20 +/-0.9 1.2 1.5 33.7 37.2 36.4 46.3 44.4 21 24 23.7 24 20 +/-0.9 1.1 1.5 34.8 38.1 38.7 44.1 48.6 22.5 25.1 25.3 6 7 Power Supply Supply Voltage (VDD) 2 of 12 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A12 DS070731 RF2360 Parameter Overall (75 Ω) Frequency Range Input VSWR 5 1.6:1 1500 MHz Min. Specification Typ. Max. Unit Condition T=25oC, VDD =7V, 75 Ω System, PIN =-8dBm 3dB Bandwidth Appropriate values for the output DC blocking capacitor and bias inductor are required to maintain this VSWR over the intended operating frequency range. See note for input VSWR. Output VSWR Gain Gain Flatness Output IP3 Output IP2 Output IP1dB 1.3:1 20 + 0.5 36.8 36.0 50.1 21 23 22 dB dB dBm dBm dBm dBm dBm dBm 109 mA At 500MHz 5MHz to 1000MHz At 50MHz, Delta F1 and F2 = 1MHz At 500MHz At 500MHz, Delta F1 and F2 = 55.25MHz At 10MHz At 500MHz At 1000MHz 10dBmV per channel, flat, at the input of the amplifier; VCC =7V, ICC =120mA Operating Current Range 100 104 110 Channels CTB -75 -77 -75 CSO+1.25MHz -91 -60 -57 CSO-1.25MHz -55 -54 -56 CNR +66 +65 +65 dBc dBc dBc dBc dBc dBc dBc dBc dBc dB dB dB 9 130 V mA At 55.25MHz At 331.25MHz At 547.25MHz At 55.25MHz At 331.25MHz At 547.25MHz At 55.25MHz At 331.25MHz At 547.25MHz At 55.25MHz At 331.25MHz At 547.25MHz Power Supply Supply Voltage (VDD) Operating Current Range 6 115 7 120 Rev A12 DS070731 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 3 of 12 RF2360 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Function NC NC GND GND GND RF IN NC NC NC NC NC GND GND RF OUT Description No connection. This pin should be connected to the ground plane. Same as pin 1. Ground connection. Keep traces physically short and connect immediately to ground plane for best performance. Each ground pin should have a via to the ground plane. Same as pin 3. Same as pin 3. RF input pin. This pin is internally DC blocked. An external DC blocking capacitor is not required. Same as pin 1. Same as pin 1. Same as pin 1. Same as pin 1. Same as pin 1. Same as pin 3. Same as pin 3. RF output and bias pin. Because DC is present on this pin, a DC blocking capacitor, suitable for the frequency of operation, should be used in most applications. For biasing, only an RF choke is needed. RF OUT Interface Schematic RF IN 15 16 NC NC Same as pin 1. Same as pin 1. 4 of 12 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A12 DS070731 RF2360 Package Drawing -A0.158 0.150 0.021 0.014 0.009 0.004 0.392 0.386 0.069 0.064 0.050 0.244 0.230 8° MAX 0° MIN 0.010 0.008 0.060 0.054 0.035 0.016 Application Schematic 869-894MHz Narrowband Operation VDD 1 2 3 4 5 8.2 nH 100 pF RF IN 2 pF 6 7 8 11 10 9 16 15 3 pF 14 100 pF 13 12 100 pF 8.2 nH RF OUT Rev A12 DS070731 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 5 of 12 RF2360 Evaluation Board Schematic - 50 Ω P1 1 2 P1-3 3 GND GND VDD 2 3 4 L1 4.7 nH 5 6 7 8 15 14 13 12 11 10 9 L2 1 μH C2 10 nF 1 16 P1-3 C1 10 nF J2 OUT J1 IN 2360400 Rev 1 6 of 12 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A12 DS070731 RF2360 Evaluation Board Schematic - 75 Ω High Frequency (50MHz to 2000MHz) P1 1 2 P1-3 3 GND GND VDD 2 3 4 C3 10 nF C1 1.5 pF L1 10 nH 5 6 7 8 15 14 13 12 11 10 9 C4 390 pF L3 10 μH C2 10 nF J2 OUT 1 16 P1-3 J1 IN 2360401- NOTES: J1 and J2 are 75 Ω F connectors. Evaluation Board Schematic - 75 Ω Low Frequency (5MHz to 200MHz) P1 1 2 P1-3 3 GND GND VDD 2 3 4 5 J1 IN L1 10 nH R1 68 Ω 6 7 8 15 14 13 12 11 10 9 C1 10 nF L1 10 μH C2 10 nF J2 OUT 1 16 P1-3 2360402- NOTES: J1 and J2 are 75 Ω F connectors. Rev A12 DS070731 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 7 of 12 RF2360 Evaluation Board Layout - 50 Ω Board Size 1.5” x 1.5” Board Thickness 0.031”, Board Material FR-4 8 of 12 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A12 DS070731 RF2360 Evaluation Board Layout - 75 Ω High Frequency (50MHz to 2000MHz) Board Size 1.25” x 1.0” Board Thickness 0.062”, Board Material FR-4 Evaluation Board Layout - 75 Ω Low Frequency (5MHz to 200MHz) Rev A12 DS070731 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 9 of 12 RF2360 55.0 50.0 45.0 Gain, OIP2 and OIP3 versus Frequency VCC = 9V, Temp = 25°C, PIN = -8dBm 50.0 Gain, OIP2 and OIP3 versus Temperature VCC = 9V, PIN = -8dBm, F = 500MHz Gain (dB), OIP2 (dBm), OIP3 (dBm) 45.0 40.0 35.0 Gain 30.0 25.0 20.0 15.0 10.0 0.0 500.0 1000.0 1500.0 2000.0 IP3 IP2 Gain (dB), OIP2 (dBm), OIP3 (dBm) 40.0 35.0 Gain IP3 30.0 IP2 25.0 20.0 15.0 -40.0 -20.0 0.0 20.0 40.0 60.0 80.0 Frequency (MHz) Temperature (°C) 50.0 Gain, OIP2 and OIP3 versus PIN VCC = 9V, Temp = 25°C, F = 500MHz 45.0 Gain (dB), OIP2 (dBm), OIP3 (dBm) 40.0 35.0 Gain 30.0 IP3 IP2 25.0 20.0 15.0 10.0 -8.0 -6.0 -4.0 -2.0 0.0 2.0 4.0 6.0 Pin (dBm) 10 of 12 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A12 DS070731 RF2360 75 Smith 8V, 25°C Ohm, Chart 1.0 0 .6 Swp Max 2.001GHz 2. 0 0.8 10.0 1.0 5.0 0.2 0.4 0.6 0.8 2.0 3.0 4.0 0 S[2,2] 0 -0 .4 - 0. 6 -2 .0 Swp Min 0.001GHz -0.8 5050OHM - Return Loss Ohm, 8V – Return Loss 1.0 0.6 -1.0 0 .6 Swp Max 3000MHz 2. 0 1.0 0.8 0.8 S[1,1] S[1,1] 3.0 2.0 S[2,2] 10.0 10.0 0.2 0.4 0.6 0.8 1.0 2.0 3.0 4.0 5.0 0.2 0.4 0.6 0.8 2.0 3.0 4.0 1.0 5.0 0 10.0 0 .4 -0 .4 -0 0 -0. 6 . -2 -0.8 - 0. 6 -2 .0 Swp Min 0.03MHz Swp Min 1MHz -1.0 -0.8 Rev A12 DS070731 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. -1.0 -5.0 - 4. 0 -3 .0 -4. 0 -5.0 -0.2 - 0 .2 -10.0 0 .2 4.0 5.0 0. 4 -10.0 -5.0 -0.2 -10.0 - 4. -3 .0 -3 . 0 0. 4 0. 4 0 3. 4 .0 5.0 0.2 10.0 S[1,1] 75OHM Return Loss 75 Ohm, 8V- – Return Loss Swp Max 3000MHz 0 3. 4 .0 5 .0 0.2 S[2,2] 10.0 11 of 12 RF2360 RoHS* Banned Material Content RoHS Compliant: Package total weight in gram Compliance Date Code: Bill of Materials Revision: Pb Free Category: yes 0.139 0435 e3 Pa r ts Pe r Mi l l i o n (PPM) Pb 0 0 0 0 0 0 Cd 0 0 0 0 0 0 Hg 0 0 0 0 0 0 Cr VI 0 0 0 0 0 0 PB B 0 0 0 0 0 0 PB DE 0 0 0 0 0 0 B i l l o f Ma te r i a l s Di e Mo l d i ng Co mp o und Le a d F r a m e Di e Atta ch Ep o x y Wi r e So l d e r Pl a ti ng Thi s R o HS b a nne d ma te r i a l co nte nt de cl a r a ti o n wa s pr e p a r e d so l e l y o n i nfo r ma ti o n, i ncl ud i ng a na l y ti ca l d a ta , pr o v i de d to R F MD b y i ts sup p l i e r s, a nd a pp l i e s to the B i l l o f M a te r i a l s (B OM) r e vi si o n no te d * DIRECTIVE 2002/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment 12 of 12 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A12 DS070731