RF2617

RF2617 10 Typical Applications • 3V CDMA/FM Cellular Systems • Supports Dual-Mode AMPS/CDMA • Supports Dual-Mode TACS/CDMA • General Purpose Linear IF Amplifier • Commercial and Consumer Systems • Portable Battery Powered Equipment 3V CDMA/FM RECEIVE AGC AMPLIFIER Product Description The RF2617 is a complete AGC amplifier designed for the receive section of 3V dual-mode CDMA/FM cellular applications. It is designed to amplify IF signals while providing more than 90dB of gain control range. Noise Figure, IP3, and other specifications are designed to be compatible with the IS-95 Interim Standard for CDMA cellular communications. This circuit is designed as part of the RFMD CDMA Chip Set, consisting of a Transmit IF AGC Amp, a Transmit Upconverter, a Receive LNA/Mixer, and this Receive IF AGC Amp. The IC is manufactured on an advanced high frequency Silicon Bipolar process, and is packaged in a standard miniature 16-lead plastic SSOP package. 0.157 0.150 0.012 0.008 0.196 0.189 0.025 0.0688 0.0532 -A0.0098 0.0040 0.2440 0.2284 8° MAX 0°MIN 0.050 0.016 0.0098 0.0075 NOTES: 1. Shaded lead is Pin 1. 2. All dimensions are excluding mold flash. 3. Lead coplanarity - 0.005 with respect to datum "A". Optimum Technology Matching® Applied Si Bi-CMOS SiGe HBT Si CMOS • Supports Dual Mode Operation CDMA+ 1 CDMA- 2 GND 3 FM+ 4 FM- 5 GND 6 IN SELECT 7 NC 8 IN SEL. GAIN CONTROL 16 GC 15 VCC 14 VCC 13 VCC 12 GND 11 GND 10 OUT+ 9 OUT- • -48dB to +48dB Gain Control Range • Single 3V Power Supply • Digitally Selectable Inputs • -2dBm Input IP3 • 12MHz to 285MHz Operation Ordering Information RF2617 RF2617 PCBA 3V CDMA/FM Receive AGC Amplifier Fully Assembled Evaluation Board Functional Block Diagram RF Micro Devices, Inc. 7625 Thorndike Road Greensboro, NC 27409, USA Tel (336) 664 1233 Fax (336) 664 0454 http://www.rfmd.com Rev B4 010717 10-17 IF AMPLIERS üSi BJT Package Style: SSOP-16 10 GaAs HBT GaAs MESFET Features RF2617 Absolute Maximum Ratings Parameter Supply Voltage Control Voltage Input RF Power Operating Ambient Temperature Storage Temperature Value -0.5 to +7.0 -0.5 to +5.0 +10 -40 to +85 -40 to +150 Unit VDC VDC dBm °C °C Caution! ESD sensitive device. RF Micro Devices believes the furnished information is correct and accurate at the time of this printing. However, RF Micro Devices reserves the right to make changes to its products without notice. RF Micro Devices does not assume responsibility for the use of the described product(s). Parameter Specification Min. Typ. Max. Unit Condition T=25°C, 85MHz, VCC =3.0V, ZS =500 Ω, ZL =500 Ω, 500 Ω External CDMA Input Terminating Resistor, 500 Ω External Output Terminating Resistor (Effective ZS =333 Ω, Effective ZL =250 Ω) (See application schematic). Overall Frequency Range CDMA Maximum Gain CDMA Minimum Gain FM Maximum Gain FM Minimum Gain Gain Slope Gain Control Voltage Range Gain Control Input Impedance Noise Figure Input IP3 +45 +45 10 IF AMPLIERS Stability (Max VSWR) -44 -4 10:1 12 to 285 +48 -48 +49 -48 57 0 to 3 30 5 -40 -2 -45 -45 8 MHz dB dB dB dB dB/V VDC kΩ dB dBm dBm VGC =2.4V VGC =0.3V VGC =2.4V VGC =0.3V Measured in 0.5V increments Source impedance of 4.7kΩ At maximum gain and 85MHz At +40dB gain, referenced to 500 Ω At minimum gain, referenced to 500 Ω Spurious