RF2861PCBA-41X

RF2861CDMA Low Noise Amplifier/Mixer 900MHz Downconverter RF2861 CDMA LOW NOISE AMPLIFIER/MIXER 900MHz DOWNCONVERTER RoHS Compliant & Pb-Free Product Package Style: QFN, 16-Pin, 3x3 ENABLE TX BUFF ENABLE LO OUT 14 Features 3 mmx3mm LNA/Mixer Solution Adjustable LNA and Mixer Current/IIP3 Meets IMD Tests with Three Gain States/Two Logic Control Pins Integrated TX LO Buffer Amplifier Full ESD Protection on all Pins G2 1 LNA IN 2 LNA EMITTER 3 LNA OUT 4 16 15 VCC 13 12 LO IN 11 GND 10 IF OUT9 IF OUT+ 8 MIX IN 5 ISET2 6 ISET1 7 G1 Applications CDMA/JCDMA Cellular Systems CDMA450 Handsets/Data Cards AMPS Cellular Systems General Purpose LNA and Downconverter Commercial and Consumer Systems Portable Battery-Powered Equipment Functional Block Diagram Product Description The RF2861 is a receiver front-end for CDMA cellular applications, including JCDMA and CDMA450. It is designed to amplify and downconvert RF signals, using a three gain state LNA to obtain 17dB of stepped gain control. Features include digital control of LNA gain and power down mode, along with an integrated TX LO buffer amplifier. Another feature of the chip is adjustable IIP3 of the LNA and mixer using off-chip current setting resistors to allow for minimum DC current consumption. Noise figure, IIP3, and other specs are designed to be compatible with the TIA/EIA 98D standard for CDMA cellular communications. The IC is manufactured on an advanced Silicon Germanium Bi-CMOS process and is in a 3mmx3mm, 16-pin, QFN. Ordering Information RF2861 RF2861PCBA-41X CDMA Low Noise Amplifier/Mixer 900MHz Downconverter Fully Assembled Evaluation Board Optimum Technology Matching® Applied GaAs HBT GaAs MESFET InGaP HBT SiGe BiCMOS Si BiCMOS SiGe HBT GaAs pHEMT Si CMOS Si BJT GaN HEMT RF MICRO DEVICES®, RFMD®, Optimum Technology Matching®, Enabling Wireless Connectivity™, PowerStar®, POLARIS™ TOTAL RADIO™ and UltimateBlue™ are trademarks of RFMD, LLC. BLUETOOTH is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed for use by RFMD. All other trade names, trademarks and registered trademarks are the property of their respective owners. ©2006, RF Micro Devices, Inc. Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 1 of 16 RF2861 Absolute Maximum Ratings Parameter Supply Voltage Input LO and RF Levels Operating Ambient Temperature Storage Temperature Rating -0.5 to +5.0 +6 -40 to +85 -40 to +150 Unit VDC dBm °C °C Caution! ESD sensitive device. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. RoHS status based on EUDirective2002/95/EC (at time of this document revision). The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents, or other rights of third parties, resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. Parameter Overall RF Frequency Range IF Frequency Range Min. Specification Typ. 460 to 900 Max. Unit MHz Condition T = 25°C, VCC =2.75V 0.1 2.65 1.8 2.75 400 3.15 0.4 MHz V V V Freq=869MHz to 894MHz Freq=832MHz to 870MHz LNA 50 Ω match Power Supply Supply Voltage Logic High Logic Low Cellular CDMA Band JCDMA Band LNA (High Gain) Gain Noise Figure Input IP3 Current Isolation 18.5 4.0 7.0 12.5 -4.0 +25.0 1.0 9.0 +6.0 36 10.5 7.5 +8.5 12.0 8.0 -2.5 2.5 +27.0 0 -1.0 4.0 6.0 3.0 9.0 3.5 7.0 3.3 9.0 13.0 14.5 1.1 11.0 7.0 16.0 1.3 dB dB dBm mA dB dB dB dBm mA dB dB dB dBm mA dB LNA (Mid Gain) Gain Noise Figure Input IP3 Current Isolation LNA (Low Gain) Gain Noise Figure Input IP3 Current Isolation Mixer - CDMA/JCDMA/FM Gain Noise Figure Input IP3 LO to RF Isolation dB dB dBm dB IF tune set for nominal mixer gain, high IIP3 184MHz IF (NF=8.3dB, 85MHz IF) LO=1064MHz 2 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 Parameter Mixer - CDMA/JCDMA/FM Gain Noise Figure Input IP3 LO to RF Isolation 36 25 30 13.0 7.5 +6.5 dB dB dBm dB mA LO=1064MHz TX LO Buffer Off 184MHz IF (NF=8.3dB, 85MHz IF) Min. Specification Typ. Max. Unit Condition IF tune set for high mixer gain, nominal IIP3 Cascade - High Gain Current Cellular CDMA Band JCDMA Band, cont’d Other LO-IF Isolation RF-IF Isolation LNA Out to Mixer In Isolation LO-LNA In Isolation, Any State 30 45 45 40 1 dB dB dB dB pF LO=1064MHz G1, G2, ENABLE, TX BUFF ENABLE LO=1064MHz Control Lines Input Capacitance Local Oscillator Input Cellular - CDMA or FM Input Power Input Frequency -10 685 1053 784 954 Cellular - JCDMA Input Power Input Frequency CDMA450 Input Power Input Frequency -10 505 -4 0 575 dBm MHz IF=85MHz Freq=463MHz to 467MHz LNA 50 Ω match 15.0 1.4 +8.0 8.7 18.5 +2.5 2.9 +14.0 4.7 12.5 dB dB dBm mA dB dB dB dBm mA dB -10 722 942 -4 0 760 980 dBm MHz MHz IF=110MHz IF=110MHz -4 0 710 1078 809 979 dBm MHz MHz MHz MHz IF=184MHz IF=184MHz IF=85MHz IF=85MHz CDMA450 Band LNA (High Gain) Gain Noise Figure Input IP3 Current Isolation LNA (Mid Gain) Gain Noise Figure Input IP3 Current Isolation Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 3 of 16 RF2861 Parameter LNA (Low Gain) Gain Noise Figure Input IP3 Current Isolation 1.0 12.0 7.5 5.0 36 25 40 40 30 -4.0 4.0 +25.0 0 dB dB dBm mA dB IF tune set for high mixer gain, nominal IIP3 dB dB dBm dB dB dB dB dB LO=549MHz LO=549MHz LO=549MHz Min. Specification Typ. Max. Unit Condition Mixer Gain Noise Figure Input IP3 LO to RF Isolation CDMA450 Isolation LO-IF Isolation RF-IF Isolation LNA Out to Mixer In Isolation LO-LNA In Isolation, Any State TX (Local Oscillator) Buffer Output Cellular - CDMA or FM Output Power Output Frequency -7 685 1053 784 954 Current Consumption Cellular - JCDMA Output Power Output Frequency Current Consumption CDMA450 Output Power Output Frequency Current Consumption -7 505 2 -5 -3 575 dBm MHz mA Single-ended 50 Ω load IF=85MHz -7 722 942 2 -5 -3 760 980 dBm MHz MHz mA Single-ended 50 Ω load IF=110MHz IF=110MHz 2 -5 -3 710 1078 809 979 dBm MHz MHz MHz MHz mA Single-ended 50 Ω load IF=184MHz IF=184MHz IF=85MHz IF=85MHz 4 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 Gain Control Logic Table Gain State High Gain Mid Gain Low Gain Low Gain (alternate) ENABLE 1 1 1 1 G1 0 1 1 0 G2 0 0 1 1 NOTES: All IDC current numbers include bias circuitry current of 1.5mA to 2.0mA (dependent on mode). TX Buffer On: Add 2mA to total current. Cell Band Cascaded Performance High Mixer Gain Nominal IIP3 (Typical Values for VCC =2.75V) NOTE: All total current numbers include bias circuitry current of 1.5mA to 2.0mA (dependent on mode). Parameter LNA (High Gain) Cascaded: Gain (dB) Noise Figure (dB) Input IP3 (dBm) Total Current (mA) 25.0 2.1 -5.6 25.0 16.5 6.3 +2.0 21.5 8.0 12.5 +11.4 18.0 CELL CDMA LNA (Mid Gain) LNA (Low Gain) NOTE: Assumes 2.5dB image filter insertion loss. The TX Buffer is off. Cell Band Cascaded Performance Nominal Mixer Gain High IIP3 (Typical Values for VCC =2.75V) Parameter LNA (High Gain) Cascaded: Gain (dB) Noise Figure (dB) Input IP3 (dBm) Total Current (mA) 22.5 2.1 -3.7 25.0 14.0 6.3 +3.5 21.5 5.5 12.5 +13.3 18.0 CELL CDMA LNA (Mid Gain) LNA (Low Gain) NOTE: Assumes 2.5dB image filter insertion loss. The TX Buffer is off. CDMA450 Band Cascaded Performance (Typical Values for VCC =2.75V) Parameter LNA (High Gain) Cascaded: Gain (dB) Noise Figure (dB) Input IP3 (dBm) Total Current (mA) 24.5 2.2 -7.6 29.5 12.0 8.5 +4.5 25 5.5 14.0 +11.3 21 CDMA450 LNA (Mid Gain) LNA (Low Gain) NOTE: Assumes 2.5dB image filter insertion loss. The TX Buffer is off. Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 5 of 16 RF2861 Pin 1 Function G2 Type Description DI Gain control logic input. See logic control table. Interface Schematic G2 2 LNA IN AI Cellular LNA input. LNA IN V CC LNA OUT LNA EMITTER 3 4 5 6 7 LNA EMITTER LNA OUT ISET2 ISET1 G1 AO AO AO AO DI Cellular LNA emitter. A small inductor connects this pin to ground. Cellular LNA gain can be adjusted by the inductance. Cellular LNA output. Simple external L-C components required for matching and VCC supply. An external resistor connected to this pin sets the current of the mixer. Increasing resistance decreases current. An external resistor connected to this pin sets the current of the LNA. Increasing resistance decreases current. Gain control logic input. See logic control table. See pin 2. See pin 2. G1 8 MIX IN AI Cellular mixer RF single-end input. M IX IN 9 IF OUT+ AO CDMA IF output. Open collector. IF OUT+ IF OUT- 10 11 12 IF OUTGND LO IN AO P AI CDMA IF output. Open collector. Ground. LO single-end input. Matched to 50 Ω. See pin 9. LO IN 70 Ω 13 14 15 VCC LO OUT TX BUFF ENABLE P AO DI LO amplifier VCC external bypass capacitor may be required. LO output. Internal DC block. Drives 50 Ω. Logic input. High enables TX LO output buffer amplifiers. TX BUFF ENABLE 6 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 Pin 16 Function ENABLE Type Description DI Logic input. Low level powers down the IC. Interface Schematic ENABLE Pkg Base Legend: GND Ground connection. The backside of the package should be soldered to a top side ground pad which is connected to the ground plane with multiple vias. DI=Digital Input from Baseband ChipAI=Analog Input P=VCC or GNDAO=Analog Output P Package Drawing -A0.10 C A 0.05 C 3.00 2 PLCS 1.50 TYP 2 PLCS 0.70 0.65 0.10 C B 0.90 0.85 0.05 0.00 3.00 12° MAX 2 PLCS 0.10 C B -B- 1.37 TYP 2 PLCS -C- SEATING PLANE 2.75 SQ 0.60 0.24 TYP 0.10 M C A B 0.10 C A 0.30 0.18 PIN 1 ID R.20 1.65 SQ. 1.35 0.50 0.30 Dimensions in mm. Shaded lead is pin 1. 0.50 Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 7 of 16 RF2861 Application Schematic Differential IF Matching G2 ENABLE TX BUFF ENABLE LO OUT VCC 2.2 nH 33 nF 0603 Wire-wound Inductors 33 nF CELL LNA IN 33 nH 1 2 1.2 nH 3 33 nF 10 nH 4 VCC 3.9 pF 9.1 kΩ RF Saw 1 4 GND OUT GND 2 GND GND 3 6 16 15 14 13 12 11 10 9 C1 R1 L2 VCC L1 L3 33 nF DNI C3 IF Saw 5 4 9 10 LO IN IFIF+ 5 6 7 G1 8 C2 20 kΩ 33 nF C1 R1 L1 85 MHz IF (LO 22 pF 2.7 kΩ 72 nH FREQ=965 MHz) 184 MHz IF (LO 5.0 pF 2.7 kΩ 55 nH FREQ=1064 MHz) L2 72 nH 55 nH C2 C3 L3 220 nH 43 nH IF SAW FILTER SAWTEK 855845 EPCOS B4955 5.1 pF 5.1 pF 10 pF 10 pF IN 5 22 nH DNI 8 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 Application Schematic Single-End Matching G2 ENABLE TX BUFF ENABLE LO OUT 2.2 nH 33 nF VCC 33 nF CELL LNA IN 33 nH 1 2 1.2 nH 3 33 nF VCC 10 nH 4 16 15 14 13 12 11 10 9 LO IN C1 L1 C2 C3 R1 L2 VCC 33 nF IF Saw 5 4 9 10 IFIF+ 5 6 7 G1 8 C4 C5 L3 3.9 pF 9.1 kΩ RF Saw 2 1 4 IN GND OUT GND GND GND 3 6 20 kΩ 85 MHz IF (LO FREQ=965 MHz) 33 nF + 184 MHz IF (LO FREQ=1064 MHz) C1 (pF) 43 13 C2 (pF) 43 13 C3 DNI DNI R1 (kΩ) 2.7 2.7 L1 (nH) 72 55 L2 (nH) 72 55 C4 (pF) 5.1 10 C5 DNI DNI L3 (nH) 220 43 IF SAW FILTER SAWTEK 855845 EPCOS B4955 5 22 nH DNI Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 9 of 16 RF2861 Application Schematic Single-End Matching CDMA450 Band G2 ENABLE TX BUFF ENABLE LO OUT 2.2 nH 33 nF VCC 33 nF CELL LNA IN 33 nH 1 2 5.6 nH 3 100 pF VCC 27 nH 4 16 15 14 13 12 11 10 9 0603 Wire-wound Inductors LO IN C1* L1* IF Saw VCC 33 nF 5 4 9 10 IFIF+ C2* C3* R1* L2* 5 6 7 G1 8 C4* *Values determined by choice of IF SAW. C5* L3* 27 pF 6.8 kΩ RF Saw 2 IN 1 4 GND OUT GND GND GND 3 6 22 kΩ + + 33 nF 5 2.2 pF 33 nH 10 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 Evaluation Board Schematic ENABLE TX BUFF ENABLE C46 33 nF C54 33 nF J6 LO OUT VCC P1-1 + C20 1 uF P1 1 2 3 C7 33 nF C55 33 nF L1 33 nH 1 G2 2 3 L24 1.2 nH L21 10 nH 3.9 pF R6 9.1 kΩ R4 20.0 kΩ C2 33 nF L3 DNI C9 22.0 nH C8 1 pF C1 33 nF Freq IF (MHz) 85 184 Freq LO (MHz) 965 1064 C3 (pF) 47 13 C5 (pF) 47 13 C35 (pF) DNI DNI R2 (kΩ) 5.1 2.7 L11 (nH) 150 82 L6 (nH) 180 150 C22 (nF) 33 33 C17 (pF) 8 11 4 5 6 7 8 C3 16 15 14 13 12 11 10 9 C35 R2 L11 L6 VCC C17 C22 J4 CDMA IF CON3 J5 LO IN VCC1 P2-1 GND GND P2-2 P2-3 P2-4 P2 1 2 3 4 CON4 ENABLE TX BUF EN G 1 G 2 L17 2.2 nH C6 33 nF C4 33 nF J1 CELL LNA IN C5 C25 33 nF VCC J2 CELL LNA OUT G1 J3 CELL MIX IN Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 11 of 16 RF2861 Evaluation Board Schematic CDMA450 Band ENABLE TX BUFF ENABLE C46 33 nF C54 33 nF J6 LO OUT VCC P1-1 + C20 1 uF P1 1 2 3 C7 33 nF C55 33 nF L1 33 nH L24 5.6 nH C25 33 nF VCC J2 CELL LNA OUT L21 27 nH 1 G2 2 3 4 5 R6 6.8 kΩ R4 22 kΩ C2 33 nF L3 33 nH Freq IF (MHz) 85 Freq LO (MHz) 549 C3 (pF) 91 C5 (pF) 91 C35 (pF) DNI R2 (kΩ) 6.8 L11 (nH) 68 L6 (nH) 270 C22 (nF) 33 C17 (pF) 27 6 7 8 C3 16 15 14 13 12 11 10 9 C35 R2 L11 L6 VCC C17 C22 J4 CDMA IF CON3 J5 LO IN VCC1 P2-1 GND GND P2-2 P2-3 P2-4 P2 1 2 3 4 CON4 ENABLE TX BUF EN G 1 G 2 L17 2.2 nH C6 33 nF C4 33 nF J1 CELL LNA IN C5 2.7 pF G1 C1 33 nF C9 2.2 pF C8 DNI J3 CELL MIX IN 12 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 IF Output Interface Network Single-End IF Matching C3 IF+ IF10 9 4 5 C1 IF+ VCC IF Saw 33 nF L2 L1 R C2 IF- C1 L1, C1, C2, and R form a current combiner which performs a differential to single-ended conversion at the IF frequency and sets the output impedance. In most cases, the resonance frequency is independent of R and can be set according to the following equation: 1 f IF = ----------------------------------------------------------L1 2 π ----- ( C 1 + 2 C 2 + C EQ ) 2 Where CEQ is the equivalent stray capacitance and capacitance looking into pins 9 and 10. An average value to use for CEQ is 2.5pF. R can then be used to set the output impedance according to the following equation: 1 - 1- – 1 R = ⎛ -------------------- – ----- ⎞ ⎝4 ⋅ R ⎠ OUT R P where ROUT is the desired output impedance and RP is the parasitic equivalent parallel resistance of L1. C2 should first be set to 0 and C1 should be chosen as high as possible (not greater than 39pF), while maintaining an RP of L1 that allows for the desired ROUT. If the self-resonant frequencies of the selected C1 produce unsatisfactory linearity performance, their values may be reduced and compensated for by including C2 capacitor with a value chosen to maintain the desired FIF frequency. L2 and C3 serve dual purposes. L2 serves as an output bias choke, and C3 serves as a series DC block. In addition, L2 and C3 may be chosen to form an impedance matching network if the input impedance of the IF filter is not equal to ROUT. Otherwise, L2 is chosen to be large (suggested 120nH) and C3 is chosen to be large (suggested 22nF) if a DC path to ground is present in the IF filter, or omitted if the filter is DC-blocked. Differential IF Matching Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 13 of 16 RF2861 C2 IF Saw VCC IF+ IF10 9 4 5 IF+ L1 R C1 IF- L2 33 nF C2 L1 L1 and C1 are chosen to resonate at the desired IF frequency. C1 can be omitted and the value of L1 increased and utilized solely as a choke to provide VCC to the open-collector outputs, but it is strongly recommended that at least some small-valued C1 (a few pF) be retained for better mixer linearity performance. R is normally selected to match the input impedance of the IF filter. However, mixer performance can be modified by selecting an R value that is different from the IF filter input impedance, and inserting a conjugate matching network between the Resistive Output Network and the IF filter. C2 serve dual purposes. C2 serves as a series DC block when a DC path to ground is present in the IF filter. In addition, C2 may be chosen to improve the combine performance of the mixer and IF filter. L2 should choose to resonate with the internal capacitance of the SAW filter. Usually, SAW filter has some capacitance. Otherwise, L2 could be eliminated. A practical approach to obtain the differential matching is to tune the mixer to the correct load point for gain, IIP3, and NF using the single-end current combiner method. Second, use the component values found in the single-end approach as starting point for the differential matching. The two-shunt capacitors in the single-end could be converted in a parallel capacitor and the parallel inductor in the single-end need to be converted in two-choke inductor. Third, set the DC block capacitors (C2) in the differential-end matching to a high value (i.e., 100pF) and retune the resonate circuit (C1 & L1) and the resistor (R) for optimal performance. After optimal performance is achieved and if performance is not satisfactory, decrease the series capacitors until optimal performance is achieved. 14 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902 RF2861 PCB Design Requirements PCB Surface Finish The PCB surface finish used for RFMD’s qualification process is electroless nickel, immersion gold. Typical thickness is 3 μinch to 8 μinch gold over 180 μinch nickel. PCB Land Pattern Recommendation PCB land patterns are based on IPC-SM-782 standards when possible. The pad pattern shown has been developed and tested for optimized assembly at RFMD; however, it may require some modifications to address company specific assembly processes. The PCB land pattern has been developed to accommodate lead and package tolerances. PCB Metal Land Pattern A = 0.64 x 0.28 (mm) Typ. B = 0.28 x 0.64 (mm) Typ. C = 1.50 (mm) Sq. 1.50 Typ. 0.50 Typ. Pin 16 Dimensions in mm. B Pin 1 B B B A A Pin 12 A A C A A 0.50 Typ. 0.75 Typ. 1.50 Typ. A A B B B B Pin 8 0.55 Typ. 0.55 Typ. 0.75 Typ. Figure 1. PCB Metal Land Pattern (Top View) Rev A3 DS050902 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 15 of 16 RF2861 16 of 16 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A3 DS050902