RF3164

RF3164 0 RoHS Compliant & Pb-Free Product Typical Applications • 3V CDMA US-PCS Handset • 3V CDMA2000/1XRTT US-PCS Handset • 3V CDMA2000/1X-EV-DO US-PCS Handset • Spread-Spectrum System Product Description The RF3164 is a high-power, high-efficiency linear amplifier module specifically designed for 3V handheld systems. The device is manufactured on an advanced third generation GaAs HBT process, and was designed for use as the final RF amplifier in 3V IS-95/CDMA 2000 1X handheld digital cellular equipment, spread-spectrum systems, and other applications in the 1850MHz to 1910MHz band. The RF3164 has a digital control line for low power applications to lower quiescent current. The RF3164 is assembled in at 16-pin, 3mmx3mm, QFN package. 3.00 Pin 1 ID A 3V 1900MHz LINEAR POWER AMPLIFIER MODULE 1.45 Pin 1 ID 3.00 1.45 0.28 TYP 0.18 0.05 0.15 C 2 PLCS B 0.15 C 2 PLCS 0.40 TYP 0.20 0.10 M C A B 0.50 TYP Dimensions in mm. Shaded areas represent pin 1. 0.203 REF 0.08 C 0.08 C 0.925 0.775 0.102 REF C Optimum Technology Matching® Applied Si BJT Si Bi-CMOS InGaP/HBT GaAs HBT SiGe HBT GaN HEMT GaAs MESFET Si CMOS SiGe Bi-CMOS Package Style: QFN, 16-Pin, 3x3 Features • Input Internally Matched@50 Ω • Output Internally Matched • 28dBm Linear Output Power • 40% Peak Linear Efficiency • 28dB Linear Gain • -50dBc ACPR @ 1.25MHz VCC1 16 15 14 13 RF IN 1 GND 2 VMODE 3 Bias VREG 4 NC IM IM 12 VCC2 11 VCC2 10 VCC2 9 RF OUT Ordering Information RF3164 3V 1900MHz Linear Power Amplifier Module RF3164PCBA-41X Fully Assembled Evaluation Board 5 NC 6 NC 7 NC 8 NC Functional Block Diagram RF Micro Devices, Inc. 7628 Thorndike Road Greensboro, NC 27409, USA Tel (336) 664 1233 Fax (336) 664 0454 http://www.rfmd.com Rev A6 060504 2-1 RF3164 Absolute Maximum Ratings Parameter Supply Voltage (RF off) Supply Voltage (POUT ≤ 31dBm) Control Voltage (VREG) Input RF Power Mode Voltage (VMODE) Operating Temperature Storage Temperature Moisture Sensitivity Level IPC/JEDEC J-STD-20 Rating +8.0 +5.2 +3.9 +10 +3.9 -30 to +110 -40 to +150 MSL 2 @260 Unit V V V dBm V °C °C °C Caution! ESD sensitive device. RF Micro Devices believes the furnished information is correct and accurate at the time of this printing. RoHS marking based on EUDirective2002/95/EC (at time of this printing). However, RF Micro Devices reserves the right to make changes to its products without notice. RF Micro Devices does not assume responsibility for the use of the described product(s). Parameter High Gain Mode (VMODE Low) Operating Frequency Range Linear Gain Second Harmonics Third Harmonics Maximum Linear Output Linear Efficiency Maximum ICC ACPR @ 1.25MHz ACPR @ 1.98MHz ACPR @ 2.25MHz Input VSWR Output VSWR Stability Noise Power Specification Min. Typ. Max. Unit Condition T=25oC Ambient, VCC =3.4V, VREG =2.8V, VMODE =0V, and POUT =28dBm for all parameters (unless otherwise specified). 1850 26 1910 28 -35 -40 40 460 -50.0 -55.5 -59.0 2:1 28 37 502 -46.0 -53.0 -56.0 6:1 10:1 MHz dB dBc dBc dBm % mA dBc dBc dBc No oscillation>-70dBc No damage At 80MHz offset. T=25oC Ambient, VCC =3.4V, VREG =2.8V, VMODE =2.8V, and POUT =28dBm for all parameters (unless otherwise specified). -138 dBm/Hz Low Gain Mode (VMODE High) Operating Frequency Range Linear Gain Second Harmonics Third Harmonics Maximum Linear Output Linear Efficiency ACPR @1.25MHz ACPR @ 1.98MHz ACPR @2.25MHz Maximum ICC Linear Gain Input VSWR Output VSWR Stability 1850 26 1910 28 -35 -40 40 -50 -55 -58 130 26 2:1 MHz dB dBc dBc dBm % dBc dBc dBc mA dB 28 37 -46 -53 -56 156 POUT =16dBm POUT =16dBm No oscillation>-70dBc No damage 6:1 10:1 2-2 Rev A6 060504 RF3164 Parameter Power Supply Supply Voltage High Gain Idle Current Low Gain Idle Current VREG Current VMODE Current RF Turn On/Off Time DC Turn On/Off Time Total Current (Power Down) VREG Low Voltage (Power Down) VREG High Voltage (Recommended) VREG High Voltage (Operational) VMODE Voltage VMODE Voltage 3.2 3.4 65 55 1 250 1.2 2 0.2 2.8 4.2 95 85 2 1000 6 40 2.0 0.5 2.95 3.0 0.5 3.0 V mA mA mA uA uS uS uA V V V V V VMODE =low and VREG =2.8V VMODE =high and VREG =2.8V Specification Min. Typ. Max. Unit Condition 0 2.75 2.7 0 2.0 High Gain Mode Low Gain Mode Rev A6 060504 2-3 RF3164 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pkg Base Function RF IN GND VMODE VREG NC NC NC NC RF OUT VCC2 VCC2 VCC2 NC IM IM VCC1 GND Description RF input internally matched to 50 Ω. This input is internally AC-coupled. Ground connection. For nominal operation (High Power mode), VMODE is set LOW. When set HIGH, devices are biased lower to improve efficiency. Regulated voltage supply for amplifier bias circuit. In power down mode, both VREG and VMODE need to be LOW (2000 V NC 13 2000 V IM 15 16 14 2000 V IM 2000 V RF IN 1 GND 2 1500 V VMODE 3 2000 VREG 4 12 2000 V VCC2 11 2000 V VCC2 10 750 V VCC2 9 900 V RF OUT 5 >2000 V NC 6 750 V NC 7 750 V NC 14 >100 V IM 8 >2000 V NC 13 >300 V NC Figure 3. ESD Level - Human Body Model Machine Model (MM) Figure 4 shows the MM ESD sensitivity level for each pin to ground. The ESD test is in compliance with JESD22-A115. 200 V VCC1 16 15 200 V IM 300 V RF IN 1 GND 2 100 V VMODE 3 250 V VREG 4 12 250 V VCC2 11 250 V VCC2 10 150 V VCC2 9 50 V RF OUT 5 >300 V NC 6 200 V NC 7 200 V NC 8 >300 V NC Figure 4. ESD Level - Machine Model Rev A6 060504 2-7 RF3164 PCB Design Requirements PCB Surface Finish The PCB surface finish used for RFMD's qualification process is electroless nickel, immersion gold. Typical thickness is 3 μinch to 8 μinch gold over 180 μinch nickel. PCB Land Pattern Recommendation PCB land patterns for RFMD components are based on IPC-7351 standards and RFMD empirical data. The pad pattern shown has been developed and tested for optimized assembly at RFMD. The PCB land pattern has been developed to accommodate lead and package tolerances. Since surface mount processes vary from company to company, careful process development is recommended. PCB Metal Land Pattern A = 0.64 x 0.28 (mm) Typ. B = 0.28 x 0.64 (mm) Typ. C = 0.78 x 0.64 (mm) D = 0.64 x 1.28 (mm) E = 1.50 (mm) Sq. Dimensions in mm. 1.50 Typ. 0.75 Typ. Pin 16 B Pin 1 C B 0.50 Typ. A A A A E D 0.75 1.00 Typ. Typ. A B B B B Pin 8 0.55 Typ. 0.55 Typ. 0.75 Typ. Figure 1. PCB Metal Land Pattern (Top View) 2-8 Rev A6 060504 RF3164 PCB Solder Mask Pattern Liquid Photo-Imageable (LPI) solder mask is recommended. The solder mask footprint will match what is shown for the PCB metal land pattern with a 2mil to 3mil expansion to accommodate solder mask registration clearance around all pads. The center-grounding pad shall also have a solder mask clearance. Expansion of the pads to create solder mask clearance can be provided in the master data or requested from the PCB fabrication supplier. A = 0.74 x 0.38 (mm) Typ. B = 0.38 x 0.74 (mm) Typ. C = 1.60 (mm) Sq. Dimensions in mm. 1.50 Typ. 0.50 Typ. Pin 16 BBBB Pin 1 0.50 Typ. 0.55 Typ. A A A A C A A A A Pin 8 Pin 12 0.75 Typ. 1.50 Typ. BBBB 0.75 Typ. 0.55 Typ. Figure 2. PCB Solder Mask Pattern (Top View) Thermal Pad and Via Design The PCB land pattern has been designed with a thermal pad that matches the die paddle size on the bottom of the device. Thermal vias are required in the PCB layout to effectively conduct heat away from the package. The via pattern has been designed to address thermal, power dissipation and electrical requirements of the device as well as accommodating routing strategies. The via pattern used for the RFMD qualification is based on thru-hole vias with 0.203mm to 0.330mm finished hole size on a 0.5mm to 1.2mm grid pattern with 0.025mm plating on via walls. If micro vias are used in a design, it is suggested that the quantity of vias be increased by a 4:1 ratio to achieve similar results. Rev A6 060504 2-9 RF3164 Tape and Reel Information Carrier tape basic dimensions are based on EIA481. The pocket is designed to hold the part for shipping and loading onto SMT manufacturing equipment, while protecting the body and the solder terminals from damaging stresses. The individual pocket design can vary from vendor to vendor, but width and pitch will be consistent. Carrier tape is wound or placed onto a shipping reel either 330 mm (13 inches) in diameter or 178 mm (7 inches) in diameter. The center hub design is large enough to ensure the radius formed by the carrier tape around it does not put unnecessary stress on the parts. Prior to shipping, moisture sensitive parts (MSL level 2a-5a) are baked and placed into the pockets of the carrier tape. A cover tape is sealed over the top of the entire length of the carrier tape. The reel is sealed in a moisture barrier, ESD bag, which is placed in a cardboard shipping box. It is important to note that unused moisture sensitive parts need to be resealed in the moisture barrier bag. If the reels exceed the exposure limit and need to be rebaked, most carrier tape and shipping reels are not rated as bakeable at 125°C. If baking is required, devices may be baked according to section 4, table 4-1, column 8 of Joint Industry Standard IPC/JEDEC J-STD-033A. The following table provides useful information for carrier tape and reels used for shipping the devices described in this document. Reel Diameter Inch (mm) 7 (178) RFMD Part Number RF3164TR7 Hub Diameter Inch (mm) 2.4 (61) Width (mm) 12 Pocket Pitch (mm) 4 Feed Single Units per Reel 2500 QFN (Carrier Tape Drawing with Part Orientation) Notes: 1. All dimensions are in millimeters (mm). 2. Unless otherwise specified, all dimension tolerances per EIA-481. Ao = 3.18 ± 0.10 Bo = 3.18 ± 0.10 F = 5.50 ± 0.05 Ko = 1.02 ± 0.10 P = 4.00 ± 0.10 W = 12.00 +0.30/-0.10 4.00 ± 0.10 2.00 ± 0.05 Ø1.50±.10 1.75±0.10 0.279 ±.020 15 inch Trailer Sprocket holes toward rear of reel Pin 1 Location Top View 15 inch Leader F RF Part Number Trace Code RF Part Number Trace Code RF Part Number Trace Code RF Part Number Trace Code RF Part Number Trace Code RF Part Number Trace Code RF Part Number Trace Code W Bo P Ao Ko Direction of Feed 2-10 Rev A6 060504