SBB-1089Z

SBB1089Z SBB1089Z 50 MHz to 850 MHz, Cascadable Active Bias InGaP HBT MMIC Amplifier 50 MHz to 850 MHz, CASCADABLE ACTIVE BIAS InGaP HBT MMIC AMPLIFIER Package: SOT-89 Product Description Features RFMD’s SBB1089Z is a high performance InGaP HBT MMIC amplifier utilizing a Darlington configuration with an active bias network. The active bias network provides stable current over temperature and process Beta variations. Designed to run directly from a 5 V supply, the SBB1089Z does not require a dropping resistor as compared to typical Darlington amplifiers. The SBB1089Z product is designed for high linearity 5 V gain block applications that require small size and minimal external components. It is internally matched to 50 . Optimum Technology Matching® Applied OIP3 = 43.1 dBm at 240 MHz  P1dB = 19.6 dBm at 500 MHz     GaAs HBT   Single Fixed 5 V Supply Robust 1000 V ESD, Class 1C Patented Thermal Design and Bias Circuit Low Thermal Resistance Applications GaAs MESFET InGaP HBT  SiGe BiCMOS  Si BiCMOS  SiGe HBT GaAs pHEMT Receiver IF Amplifier Cellular, PCS, GSM, UMTS Wireless Data, Satellite Terminals Si CMOS Si BJT GaN HEMT InP HBT RF MEMS LDMOS Parameter Small Signal Gain Min. Specification Typ. Max. Unit Condition 15.5 15.5 15.5 19.0 19.0 19.0 42.0 43.0 40.5 50 to 850 18.0 16.0 3.5 18.0 dB 70 MHz 14.0 17.0 dB 240 MHz 14.0 17.0 dB 400 MHz Output Power at 1 dB Compression dBm 70 MHz dBm 240 MHz 18.0 dBm 400 MHz Third Order Intercept Point dBm 70 MHz dBm 240 MHz 38.5 dBm 400 MHz Return Loss MHz Minimum 10 dB Input Return Loss 14.0 dB 70 MHz to 5000 MHz Output Return Loss 12.0 dB 70 MHz to 5000 MHz Noise Figure 4.2 dB 500 MHz Reverse Isolation dB 70 MHz to 5000 MHz -55 +110 °C Operating Temp Range (TL) Thermal Resistance 48.8 °C/W junction - lead Device Operating Voltage 5.0 5.3 V Device Operating Current 82.0 90.0 98.0 mA Test Conditions: VD = 5 V, ID = 90 mA Typ., OIP3 Tone Spacing = 1 MHz, POUT per tone = 0 dBm, TL = 25°C, ZS = ZL = 50 , Tested with Bias Tees RF MICRO DEVICES®, RFMD®, Optimum Technology Matching®, Enabling Wireless Connectivity™, PowerStar®, POLARIS™ TOTAL RADIO™ and UltimateBlue™ are trademarks of RFMD, LLC. BLUETOOTH is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed for use by RFMD. All other trade names, trademarks and registered trademarks are the property of their respective owners. ©2006, RF Micro Devices, Inc. DS150722 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 1 of 9 SBB1089Z Absolute Maximum Ratings Rating Unit Device Current (ID) Parameter 110 mA Device Voltage (VD) 5.5 V RF Input Power 24 dBm Junction Temp (TJ) +150 °C Storage Temp +150 °C 0.61 W Power Dissipation ESD Rating - Human Body Model (HBM) Moisture Sensitivity Level Class 1C Caution! ESD sensitive device. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. RoHS status based on EU Directive 2002/95/EC (at time of this document revision). The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents, or other rights of third parties, resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. MSL2 Operation of this device beyond any one of these limits may cause permanent damage. For reliable continuous operation, the device voltage and current must not exceed the maximum operating values specified in the table on page one. Bias Conditions should also satisfy the following expression: IDVD < (TJ - TL) / RTH, j-l and TL = TLEAD Typical RF Performance at Key Operating Frequencies (With 240 MHz Application Circuit) Parameter Unit 50 MHz 70 MHz 100 MHz Small Signal Gain, S21 dB 16.0 15.5 15.5 dBm 41.5 42.0 43.0 Output Third Order Intercept Point, OIP3 dBm 19.0 19.0 19.0 Output Power at 1dB Compression, P1dB dB 13.0 16.0 17.0 Input Return Loss, S11 dB 18.0 20.0 21.0 Output Return Loss, S22 Reverse Isolation, S12 dB 18.0 18.0 18.0 Noise Figure, NF dB 3.5 3.3 3.2 Test Conditions: VCC = 5 V ID = 90 mA Typ. OIP3 Tone Spacing = 1 MHz, POUT per tone = 0 dBm TL = 25°C 2 of 9 240 MHz 400 MHz 500 MHz 850 MHz 15.5 15.5 43.0 41.0 19.0 19.0 19.0 19.0 23.0 24.0 18.0 18.0 3.1 3.2 ZS = ZL = 50  15.5 40.0 19.0 18.0 23.0 18.0 3.2 15.0 35.0 18.0 15.0 17.0 18.0 3.4 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. DS150722 SBB1089Z Data on Charts taken with 240 MHz App. Ckt. DS150722 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 3 of 9 SBB1089Z S-Parameters over Temperature (Bias Tee) 4 of 9 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. DS150722 SBB1089Z 240 MHz Application Circuit S-Parameters over Temperature DS150722 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 5 of 9 SBB1089Z Pin 1 2, 4 Function RF IN GND 3 RF OUT/BIAS Description RF input pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. Connection to ground. Use via holes for best performance to reduce lead inductance as close to ground leads as possible. RF output and bias pin. DC voltage is present on tis pin, therefore a DC blocking capacitor is necessary for proper operation. Suggested PCB Pad Layout Preliminary Package Drawing Dimensions in inches (millimeters) Refer to drawing posted at www.rfmd.com for tolerances. 6 of 9 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. DS150722 SBB1089Z Application Circuit Element Values Reference Designator Frequency (MHZ) 50 to 850 CB 8200 pF 1500 nH 0805LS Coilcraft 2.7 nH Toko LC LS Application Schematic Vs 1uF 1200pF 4 1 RF in Lc 3 SBB-1089 Cb Ls 2 RF out Cb t Evaluation Board Layout DS150722 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 7 of 9 SBB1089Z Package Marking Ordering Information 8 of 9 Ordering Code Description SBB1089Z 7” Reel with 1000 pieces SBB1089ZSQ Sample bag with 25 pieces SBB1089ZSR 7” Reel with 100 pieces SBB1089ZPCK1 50 MHz to 850 MHz PCBA with 5-piece sample bag 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. DS150722 SBB1089Z DS150722 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. 9 of 9