9091

9000 Series / Molded SIP Reed Relays HIGH PERFORMANCE SIP REED RELAYS S IP The SIP relay is the industry standard when high reliability and consistent performance are desired in a compact package. The 9001 and 9002 are high performance relays ideally suited for Automatic Test Equipment, Instrumentation, RF, and Telecommunications applications. The 9091 is a compact version of the 9001. It offers many of the same features of the larger package while using 40% less board space. The specification tables allow you to select the appropriate relay for your application. SERIES FEATURES u High Insulation Resistance - 1012 Ω minimum. (1013 Ω typical) High reliability, hermetically sealed contacts for long life. Tested to 1 Billion Operations. High dielectric strength available, consult factory. High speed switching compared to electromechanical relays. Molded thermoset body on integral lead frame design. Coaxial Shield for 50 Ω impedance and switching of fast rise time digital pulses - 9002 only. Optional Coil Suppression Diode - protects coil drive circuits. UL File # E-67117, CSA File # LR 28537 Dimensions in Inches (Millimeters) Model 9001 Model 9002 30 o Model 9091 COTO TECHNOLOGY RHOPOINT COMPONENTS LTD Email: components@rhopoint.co.uk Website: www.rhopoint.co.uk 9000 Series / Molded SIP Reed Relays Model Number Parameters COIL SPECS. Nom. Coil Voltage Max. Coil Voltage Coil Resistance Operate Voltage Release Voltage CONTACT RATINGS Switching Voltage Switching Current Carry Current Contact Rating 1 Life Expectancy-Typical Static Contact Resistance (max. init.) Dynamic Contact Resistance (max. init.) RELAY SPECIFICATIONS Insulation Resistance (minimum) Capacitance - Typical Across Open Contacts Open Contact to Coil 9001 Test Conditions Units VDC VDC Ω VDC - Max. VDC - Min. Volts Amps Amps Watts 6 x 10 Ops. Ω Ω 2 9002 2 9091 2 4 Pin SIP 5 6.5 500 3.75 0.4 12 15.0 1000 9.0 1.0 200 0.5 1.5 10 1000 0.150 0.200 6 Pin SIP 5 6.5 350 3.75 0.4 12 15.0 750 9.0 1.0 200 0.5 1.5 10 1000 0.150 0.200 1 Form A 5 6.5 500 3.75 0.4 12 15.0 1000 9.0 1.0 200 0.5 1.5 10 500 0.125 0.150 +/- 10%, 25° C Must Operate by Must Release by Max DC/Peak AC Resist. Max DC/Peak AC Resist. Max DC/Peak AC Resist. Max DC/Peak AC Resist. Signal Level 1.0V, 1.0mA 50mV, 10mA 0.5V, 50mA at 100 Hz, 1.5 msec Between all Isolated Pins at 100V, 25°C, 40% RH No Shield Shield Floating Shield Guarding No Shield Shield Floating Shield Guarding Contacts Open, Shield Floating Between Contacts Contacts to Shield Contacts/Shield to Coil At Nominal Coil Voltage, 30 Hz Square Wave Zener-Diode Suppression Diode Suppression 4 Ω pF pF pF pF pF pF pF VDC/peak AC VDC/peak AC VDC/peak AC msec. msec. x 10 12 x 10 12 x 10 12 0.7 1.4 300 1500 0.35 0.10 - 0.8 0.1 1.4 0.5 1.4 300 1500 1500 0.35 0.10 - 0.1 2.0 200 1500 0.50 0.30 0.12 Top View: Dot stamped on relay refers to pin #1 Grid = .1"x.1" (2.54mm x 2.54mm) Contact to Shield Dielectric Strength (minimum) Operate Time - including bounce - Typical Release Time - Typical Notes: 1 Consult factory for life expectancy at other switching loads. 9090 series contact resistance >0.5W defines end of life or failure to open. 2 Optional diode is connected to pin #2 (+) and pin #3(-). Correct coil polarity must be observed. 3 9000 series part numbers designated with Form B contacts, these relays contain bias magnets. Correct coil polarity must be observed. 4 Consists of 20V Zener-diode and 1N1002 diode in series, connected in parallel with coil. Environmental Ratings Storage Temp:-35°C to +100°C; Operating Temp:-20°C to +85°C Solder Temp: 270°C max; 10 sec. max The operate and release voltage and the coil resistance are specified at 25°C. These values vary by approximately 0.4%/°C as the ambient temperature varies. Vibration: 20 G’s to 2000 Hz; Shock: 50 G’s COTO TECHNOLOGY RHOPOINT COMPONENTS LTD Holland Rd, Hurst Green, Oxted, Surrey, RH8 9AX,ENGLAND