0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
EVB_RT2613AGQW

EVB_RT2613AGQW

  • 厂商:

    RICHTEK(台湾立锜)

  • 封装:

    -

  • 描述:

    EVALMODULEFORRT2613AGQW

  • 数据手册
  • 价格&库存
EVB_RT2613AGQW 数据手册
RT2613AGQW Evaluation Board your power partner. 2.95V to 6V Input, 3A Output, 2MHz, Synchronous Step-Down Converter Purpose The RT2613A is a synchronous step-down converter with the input voltage range from 2.95V to 6V and provides 3A output current. This document explains the function and use of the RT2613A evaluation board (EVB), and provides information to enable operation, modification of the evaluation board and circuit to suit individual requirements. Table of Contents Purpose ................................................................................................................................................................. 1 Introduction............................................................................................................................................................ 2 Key Performance Summary Table .......................................................................................................................... 2 Bench Test Setup Conditions ................................................................................................................................. 3 Schematic, Bill of Materials & Board Layout ........................................................................................................... 5 More Information.................................................................................................................................................... 7 Important Notice for Richtek Evaluation Board ....................................................................................................... 7 EVB_RT2613AGQW-00 December 2015 1 http://www.richtek.com RT2613AGQW Evaluation Board your power partner. Introduction General Product Information The RT2613A is a high efficiency step-down converter and capable of delivering 3A output current over a wide input voltage range from 2.95V to 6V. The RT2613A provides accurate regulation for a variety of loads with ±3% accuracy. For reducing inductor size, it provides up to 2MHz switching frequency. The efficiency is maximized through the integrated 45mΩ MOSFETs and 550μA typical supply current. Under voltage lockout voltage of the RT2613A is 2.7V, and it also provides external setting by a resistor network on the enable pin. The RT2613A provides protections such as inductor current limit under voltage lockout and thermal shutdown. The over temperature threshold is 145°C. The RT2613A is available in WQFN-16L 3x3 package. Product Feature            Integrated 45mΩ MOSFETs Input Range : 2.95V to 6V Adjustable PWM Frequency : 700kHz to 2MHz Output Current : 3A 95% Efficiency Adjustable Soft-Start Power Good Indicator Enable Control Under Voltage Lockout Current Limit Thermal Shutdown Key Performance Summary Table Key Features Evaluation Board Number : PCB038_V1 Input Voltage Range 2.95V to 6V Max Output Current 3A Default Output Voltage 1.8V Default Marking & Package Type RT2613AGQW, WQFN-16L 3x3 Operation Frequency Adjustable from 700kHz to 2MHz EVB_RT2613AGQW-00 December 2015 2 http://www.richtek.com RT2613AGQW Evaluation Board your power partner. Bench Test Setup Conditions Headers Description and Placement Please carefully inspect the EVB IC and external components, comparing them to the following Bill of Materials, to ensure that all components are installed and undamaged. If any components are missing or damaged during transportation, please contact the distributor or send e-mail to evb_service@richtek.com Test Points The EVB is provided with the test points and pin names listed in the table below. Test point/ Pin name Signal Comment (expected waveforms or voltage levels on test points) VIN Input voltage Power input. EN Enable test point Externally pulled high to enable and pulled low to disable this chip. It is internally pulled up to high when the pin is floating. GND Ground The exposed pad must be soldered to a large PCB and connected to GND for maximum power dissipation. AGND Analog ground Analog ground. COMP Compensation node test point Compensation node for converter stability. FB Feedback voltage input Feedback input. PGOOD Power good test point Output of power good indicator. BOOT Bootstrap supply test point Bootstrap supply for high-side gate driver. Connect a capacitor between the BOOT and LX pins. LX Switch node test point Connect this pin to an external L-C filter. RT/SYNC Clock input Frequency Setting and External Synchronous. EVB_RT2613AGQW-00 December 2015 3 http://www.richtek.com RT2613AGQW Evaluation Board your power partner. Power-up & Measurement Procedure 1. Apply a 12V nominal input power supply (2.95V < VIN < 6V) to the VIN and GND terminals. 2. Set the jumper at JP1 to connect terminals 1 and 2, connecting EN to enable operation. 3. Verify the output voltage (approximately 1.8V) between VOUT and GND. 4. Connect an external load up to 3A to the VOUT and GND terminals and verify the output voltage and current. Output Voltage Setting Set the output voltage with the resistive divider (R1, R2) between VOUT and GND with the midpoint connected to FB. The output is set by the following formula : VOUT = 0.827 x (1 + R1 ) R2 EVB_RT2613AGQW-00 December 2015 4 http://www.richtek.com RT2613AGQW Evaluation Board your power partner. Schematic, Bill of Materials & Board Layout EVB Schematic Diagram Bill of Materials Reference Qty Part Number Description Package Manufacture U1 1 RT2613AGQW DC/DC Converter WQFN-16L 3x3 RICHTEK C1 1 C2012X5R1C106KT 10µF/16V/X5R C-0805 TDK C3 1 C1608X5R1E105KT000E 1µF/25V/X5R C-0603 TDK C5, C6 2 GRM32ER61C226KE20L 22µF/16V/X7R C-1210 MURATA C8 1 C1608X7R1H104KT000N 0.1µF/50V/X7R C-0603 TDK C10 1 0603B103K500 10nF/50V/X7R C-0603 WALSIN C11 1 0603B332K500 3.3nF/50V/X7R R-0603 WALSIN L1 1 NR8040T1R4N 1.4µH/7A 8 x 8 x 4 mm Taiyo Yuden R1 1 11.8k R-0603 R2 1 10k R-0603 R3 1 7.68k R-0603 R4 1 180k R-0603 R5 1 100k R-0603 C2, C4, C7, C9, C12, C13, R6, R7, R8 9 NC CP1 1 0 EVB_RT2613AGQW-00 December 2015 5 http://www.richtek.com RT2613AGQW Evaluation Board your power partner. PCB Layout Top View (1st layer) Bottom View (4th Layer) EVB_RT2613AGQW-00 December 2015 6 http://www.richtek.com RT2613AGQW Evaluation Board your power partner. More Information For more information, please find the related datasheet or application notes from Richtek website http://www.richtek.com. Important Notice for Richtek Evaluation Board THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS OR IMPLIED, UNDER CONTRACT, TORT OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL RICHTEK BE LIABLE T O BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES. EVB_RT2613AGQW-00 December 2015 7 http://www.richtek.com
EVB_RT2613AGQW 价格&库存

很抱歉,暂时无法提供与“EVB_RT2613AGQW”相匹配的价格&库存,您可以联系我们找货

免费人工找货
EVB_RT2613AGQW
  •  国内价格 香港价格
  • 1+390.810611+47.14945

库存:5