0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
RT8120FGSP

RT8120FGSP

  • 厂商:

    RICHTEK(台湾立锜)

  • 封装:

    SOP8_150MIL_EP

  • 描述:

    IC REGULATOR CONTROLLER

  • 数据手册
  • 价格&库存
RT8120FGSP 数据手册
® RT8120E/F Single-Phase Synchronous Buck PWM Controller General Description Features The RT8120E/F is a single-phase synchronous buck PWM DC-DC controller designed to drive two N-MOSFET. It provides a highly accurate, programmable output voltage precisely regulated to low voltage requirements with an internal 0.8V ±1% ( option for 0.6V ±1.5%) reference. The RT8120E/F uses a single feedback loop voltage mode PWM control for fast transient response. An oscillator with fixed frequency 300kHz reduces the external inductor and capacitor component size for saving PCB board area. The RT8120E/F provides fast transient response to satisfy high current output applications while minimizing external components. It is suitable for high performance graphic processors, DDR and VTT power. The RT8120E/F incorporates an externally compensated error amplifier and an internal soft-start and output enable. The RT8120E/F comes in SOP-8 and SOP-8 (Exposed Pad) packages.  Wide Input Voltage Range : 3V to 13.2V  Embedded Switching Boot Diode 0.8V ±1%, 0.6V ±1.5% Internal Reference Shoot-Through Protection and Short Pulse Free Technology for Gate Drivers Fixed Frequency 300kHz Internal Soft-Start Over Current Protection by Sensing MOSFET RDS(ON) Enable/Shutdown Control Drives Two N-MOSFETs Full Duty Cycle : 0% to 85% Fast Transient Response Voltage Mode PWM Control with External Feedback Loop Compensation Pinless LGATE Over Current Setting (LGOCS) Over Voltage Protection Under Voltage Protection SOP-8 and SOP-8 (Exposed Pad) Packages RoHS Compliant and Halogen Free               Ordering Information RT8120E/F Applications Package Type S : SOP-8 SP : SOP-8 (Exposed-Pad-Option 1) Lead Plating System G : Green (Halogen Free and Pb Free) Z : ECO (Ecological Element with Halogen Free and Pb free) Reference Voltage E : 0.6V F : 0.8V Note : Richtek products are :       System (Graphic, MB) with 5V or 12V Power Graphic Cards (AGP 8X, 4X, PCI Express*16) 3.3V to 12V Input DC-DC Regulators Low Voltage Distributed Power Supplies Pin Configuration (TOP VIEW) 8 BOOT 7 COMP/EN GND LGATE/OCSET 3 6 FB 4 5 VCC 8 PHASE RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020.  PHASE UGATE 2 SOP-8 Suitable for use in SnPb or Pb-free soldering processes. BOOT UGATE 2 GND LGATE/OCSET 3 GND 7 COMP/EN 6 FB 5 VCC 9 4 SOP-8 (Exposed Pad) Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021 is a registered trademark of Richtek Technology Corporation. www.richtek.com 1 RT8120E/F Marking Information RT8120xGS RT8120xZS RT8120xGS : Product Number RT8120x GSYMDNN RT8120xZS : Product Number RT8120x ZSYMDNN X : E or F YMDNN : Date Code RT8120xGSP X : E or F YMDNN : Date Code RT8120xZSP RT8120xGSP : Product Number RT8120x GSPYMDNN RT8120xZSP : Product Number RT8120x ZSPYMDNN X : E or F YMDNN : Date Code Typical Application Circuit VCC VIN CBypass 4.7µF C1 0.1µF R2 0 RT8120E/F VCC C4 22µF x 2 16V BOOT Q1 R3 0 IPD09N 03LA UGATE COMP/EN VOUT LOUT 0.68µH PHASE RC 13k CP 22pF CIN 1000µF 16V CC 3.3nF IPD06N03LA LGATE/ OCSET GND FB Q2 R4 1 RFB1 5k C2 3.3nF ROCSET 7.87k R5 NC C5 10µF x 2 6.3V + 2N7002 EN YMDNN : Date Code + R1 10 X : E or F COUT 820µF x 2 2.5V C3 NC RFB2 16k Functional Block Diagram VCC Internal Regulator POR BOOT UGATE VREF FB + Error Amp PWM + - - PHASE Gate Control COMP/EN VCC LGATE/ OCSET ramp SS Soft-Start/ Fault Logic fault GND + - PHASE VIN Detection Oscillator Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 2 Sample /Hold IOCSET is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F Functional Pin Description SOP-8 Pin No. SOP-8 (Exposed Pad) Pin Name 1 1 BOOT 2 2 UGATE 3 3, GND 9 (Exposed Pad) Pin Function Bootstrap Power Pin. This pin powers the upper gate driver. Connect a bootstrap capacitor between the BOOT pin and PHASE pin on the upper MOSFET. Upper-Gate Driver Output. Connect to gate of the high side power N-MOSFET. This pin is monitored by the adaptive shoot-through protection circuitry to determine when the upper MOSFET has turned off. Ground for the IC. All voltage levels are measured with respect to this pin. Connect this pin directly to the low side MOSFET source and ground plane with the lowest impedance. The exposed pad must be soldered to a large PCB and connected to GND for maximum power dissipation. Lower-Gate Driver Output. Connect to the gate of the low side power N-MOSFET. It provides the PWM-controlled gate drive (from VCC). This pin is also monitored by the adaptive shoot-through protection circuitry to determine when the lower LGATE/OCSET MOSFET has turned off. During a short period of time following Power-On Reset (POR) or shutdown release, this pin is also used to determine the over-current threshold of the converter (LGOCS). Connect a resistor (ROCSET) from this pin to GND. See the over current protection section for equations. Supply Input Pin. Connect this pin to a well-decoupled 5V or 12V VCC bias supply. It is also the positive supply for the lower gate driver, LGATE. Feedback Input Pin. This pin is the inverting input of the error FB amplifier. FB senses the switch output through an external resistor divider network. 4 4 5 5 6 6 7 7 COMP/EN 8 8 PHASE Feedback Compensation. And could be used as EN pin, when COMP < 0.4V, to disable entire chip. Switch Node. Connect this pin to the source of the upper MOSFET and the drain of the lower MOSFET. Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021 is a registered trademark of Richtek Technology Corporation. www.richtek.com 3 RT8120E/F Absolute Maximum Ratings (Note 1) VCC to GND, VCC -------------------------------------------------------------------------------------- BOOT to PHASE, VBOOT−PHASE ---------------------------------------------------------------------- PHASE to GND DC -----------------------------------------------------------------------------------------------------------< 20ns ----------------------------------------------------------------------------------------------------- UGATE to PHASE DC -----------------------------------------------------------------------------------------------------------< 20ns ----------------------------------------------------------------------------------------------------- LGATE to GND DC -----------------------------------------------------------------------------------------------------------< 20ns ----------------------------------------------------------------------------------------------------- Other Pins ------------------------------------------------------------------------------------------------- Power Dissipation, PD @ TA = 25°C SOP-8 ------------------------------------------------------------------------------------------------------SOP-8 (Exposed Pad) --------------------------------------------------------------------------------- Package Thermal Resistance (Note 2) SOP-8, θJA -----------------------------------------------------------------------------------------------SOP-8 (Exposed Pad), θJA ---------------------------------------------------------------------------SOP-8 (Exposed Pad), θJC --------------------------------------------------------------------------- Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------- Junction Temperature ----------------------------------------------------------------------------------- Storage Temperature Range -------------------------------------------------------------------------- ESD Susceptibility (Note 3) HBM (Human Body Model) ---------------------------------------------------------------------------- Recommended Operating Conditions     15V 15V −0.5V to 15V −8V to 25V −0.3V to (VBOOT−PHASE + 0.3V) −5V to (VBOOT−PHASE + 5V) −0.3V to (VCC + 0.3V) −5V to (VCC + 5V) −0.3V to 7V 0.53W 3.26W 188°C/W 30.6°C/W 3.4°C/W 260°C 150°C −65°C to 150°C 2kV (Note 4) Supply Input Voltage, VIN ------------------------------------------------------------------------------ 3V to 13.2V Control Input Voltage, VCC ---------------------------------------------------------------------------- 4.5V to 13.2V Junction Temperature Range --------------------------------------------------------------------------- −40°C to 125°C Ambient Temperature Range --------------------------------------------------------------------------- −40°C to 85°C Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 4 is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F Electrical Characteristics ( TA = 25°C, unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Supply Current ICC UGATE, LGATE Open, VCC = 12V -- 1.5 -- mA Shutdown Current ISHDN UGATE, LGATE Open, VCC = 12V -- 0.7 -- mA 3.9 4.1 4.3 V Power On Reset Threshold VCCR_TH VCC Rising Power On Reset Hysteresis VCC_Hys 0.26 0.45 0.64 V Switching Frequency f SW 270 300 330 kHz Ramp Amplitude VOSC -- 1.3 -- VP-P 0 -- -- % -- 85 -- % RT8120E 0.591 0.6 0.609 RT8120F 0.792 0.8 0.808 Minimum Duty Cycle Maximum Duty Cycle DMAX Reference Voltage VREF Open Loop DC Gain ADC Guaranteed by Design -- 70 -- dB Gain Bandwidth GBW Guaranteed by Design -- 10 -- MHz Slew Rate SR Guaranteed by Design, CL = 10pF -- 6 -- V/s Transconductance gm 500 700 -- A/V Output Source Current ICOMPSK VFB < VREF 80 120 -- A Output Sink Current ICOMPSC VFB < VREF 80 120 -- A Soft-Start Time RT8120E -- 1.5 -- tSS RT8120F -- 2 -- Upper Gate Sourcing Ability IUG_SRC VBOOT  VPHASE = 12V, max source current -- 1.2 -- A Upper Gate RDS(ON) Sinking RUG_SNK VUGATE  VPHASE = 0.1V -- 3 --  Lower Gate Sourcing Ability ILG_SRC VCC = 12V, max source current -- 1.2 -- A Lower Gate RDS(ON) Sinking RLG_INK VLGATE = 0.1V -- 1.8 --  Deadtime between UGATE Off to LGATE On VUGATE  VPHASE = 1.2V to VLGATE =1.2V -- 30 -- ns Deadtime Between LGATE Off to UGATE On VUGATE  VPHASE = 1.2V to VLGATE = 1.2V -- 30 -- ns RBOOT VCC to BOOT, 10mA -- -- 80  Under Voltage Protection VUVP_FB Relative to FB Pin Voltage -- 75 -- % Pre-OVP Threshold (Before POR) VOVP1 VCC = 3V, FB Pin Voltage -- 1.3 -- V V ms Internal BOOT Switch Internal BOOT Switch On-Resistance Protection Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021 is a registered trademark of Richtek Technology Corporation. www.richtek.com 5 RT8120E/F Parameter OVP Threshold (After POR) Symbol VOVP2 Test Conditions VCC = 5V, Relative to FB Pin Voltage LGATE OC Setting Current IOCSET Over Current Threshold VPHASE Enable Threshold VEN ROCSET = Open Min Typ Max Unit -- 125 -- % 9 10 11 A -- 375 -- mV 0.3 0.4 0.55 V Note 1. Stresses beyond those listed “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Note 2. θJA is measured at TA = 25°C on a high effective thermal conductivity four-layer test board per JEDEC 51-7. θJC is measured at the exposed pad of the package. Note 3. Devices are ESD sensitive. Handling precaution is recommended. Note 4. The device is not guaranteed to function outside its operating conditions. Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 6 is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F Typical Operating Characteristics Output Voltage vs. Output Current Efficiency vs. Output Current 1.500 100 95 1.495 Output Voltage (V) Efficiency (%) 90 85 80 75 70 65 60 1.490 1.485 1.480 1.475 55 VIN = VCC = 12V, VOUT = 1.5V VIN = VCC = 12V, VOUT = 1.5V 1.470 50 0 5 10 15 20 25 0 30 2 4 6 8 10 12 14 16 18 20 Output Current (A) Output Current (A) Reference Voltage vs. Temperature Frequency vs. Temperature 300 0.820 290 0.810 Frequency (kHz)1 Reference Voltage (V) 0.815 0.805 0.800 0.795 0.790 280 270 260 0.785 VIN = VCC = 12V VIN = VCC = 12V 250 0.780 -50 -25 0 25 50 75 100 125 -50 0 25 50 75 Temperature (C) Power On Power Off VUGATE (20V/Div) VUGATE (20V/Div) VLGATE (10V/Div) VLGATE (10V/Div) V CC (10V/Div) VOUT (1V/Div) V CC (10V/Div) VOUT (1V/Div) VIN = VCC = 12V, VOUT = 1.05V, ILOAD = 10A Time (2.5ms/Div) Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 -25 Temperature (C) September 2021 100 125 VIN = VCC = 12V, VOUT = 1.05V, ILOAD = 10A Time (2.5ms/Div) is a registered trademark of Richtek Technology Corporation. www.richtek.com 7 RT8120E/F COMP/EN Power On COMP/EN Power Off VUGATE (20V/Div) VUGATE (20V/Div) VLGATE (10V/Div) VLGATE (10V/Div) V COMP/EN (1V/Div) VOUT (1V/Div) V COMP/EN (2V/Div) VOUT (2V/Div) VIN = VCC = 12V, VOUT = 1.05V, ILOAD = 10A VIN = VCC = 12V, VOUT = 1.05V, ILOAD = 10A Time (500μs/Div) Time (250μs/Div) Load Transient Response Load Transient Response VUGATE (20V/Div) VUGATE (20V/Div) I LOAD (10A/Div) I LOAD (10A/Div) VOUT (50mV/Div) VOUT (50mV/Div) VIN = VCC = 12V, VOUT = 1.05V, ILOAD = 0A to15A VIN = VCC = 12V, VOUT = 1.05V, ILOAD = 15A to 0A Time (10μs/Div) Time (10μs/Div) Over Current Protection Under Voltage Protection VIN = VCC = 12V, VOUT = 1.05V VUGATE (20V/Div) VLGATE (20V/Div) VUGATE (10V/Div) VLGATE (10V/Div) Inductor Current (20A/Div) VOUT (1V/Div) ROCSET = 6.2kΩ Low side MOSFET = IPD06N03 x 2 Time (25μs/Div) Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 8 VFB (500mV/Div) VIN = VCC = 12V, VOUT = 1.05V, No Load Time (2.5ms/Div) is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F Application Information Function Description The RT8120E/F is a single-phase synchronous buck PWM controller with integrated N-MOSFET gate drivers. The RT8120E/F can be used in a broad variety of applications, with its wide input voltage range from 3V or 13.2V. It provides single feedback loop, voltage mode control with fast transient response. An internal 0.8V (option for 0.6V) reference allows the output voltage to be precisely regulated for low output voltage applications. A fixed frequency (300kHz) oscillator is integrated to minimize external components. Protection features include programmable over current protection and Under Voltage Lockout (UVLO). Supply Voltage and Power On Reset (POR) The input voltage range for VCC is from 4.5 V to 13.2 V with respect to GND. An internal linear regulator regulates the supply voltage for internal control logic circuit. A minimum 0.1μF ceramic capacitor is recommended to bypass the supply voltage. Place the bypassing capacitor physically near the IC. VCC also supplies the integrated MOSFET drivers. A bootstrap diode is embedded to facilitate PCB design and reduce the total BOM cost. No external Schottky diode is required in real applications. The Power-On Reset (POR) circuit monitors the supply voltage at the VCC pin. If VCC exceeds the POR rising threshold voltage (typ. 4V), the controller resets and prepares the PWM for operation. If VCC falls below the POR falling threshold during normal operation, all MOSFETs stop switching. The POR rising and falling threshold has a hysteresis (typ.0.45V) to prevent unintentional noise based reset. Chip Enable and Disable The COMP/EN pin of the RT8120E/F is a multiplexed pin. During soft-start and normal converter operation, this pin represents the output of the error amplifier. When COMP/ EN pin voltage falls or is pulled externally below the enable level VEN, the chip shuts down. When the controller shuts down, UGATE and LGATE signals will go low. When the pull-down device is released and the COMP/EN pin rises above the VEN trip point, the RT8120E/F will begin a new Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021 initialization and soft-start cycle. This allows flexible power sequence control for specified application. In practical applications, connect a small-signal MOSFET to the COMP/EN pin to implement the enable/disable function. VIN Detection Once VCC exceeds its power on reset (POR) rising threshold voltage, UGATE will output continuous pulses (~60kHz, 200ns), and LGATE will be forced low for converter input voltage VIN detection. If the voltage pulses at the PHASE pin exceed 1V when UGATE is turned on, VIN is recognized as ready. Then, the controller will initiate soft-start operation. Internal Soft-Start The RT8120E/F provides an internal soft-start function. The soft-start function is used to prevent large inrush current and output voltage overshoot while the converter is being powered-up. The soft-start function automatically begins once the chip is enabled. An internal current source charges the internal soft-start capacitor such that the internal soft-start voltage ramps up uniformly. The FB voltage will track the internal soft-start voltage during the soft-start interval. Therefore, the PWM pulse width increases gradually to limit the input current. After the internal soft-start voltage exceeds the reference voltage, the FB voltage no longer tracks the soft-start voltage but rather follows the reference voltage. Therefore, the duty cycle of the UGATE signal as well as the input current at power up are limited. Over Current Protection (OCP) The RT8120E/F provides lossless over current protection by detecting the voltage drop across the low side MOSFET when it is turned on. The over current trip threshold is set by an external resistor, ROCSET, at LGATE. During the initial stage when LGATE is turned on, the RT8120E/F samples and holds the phase voltage. The sample-and-hold voltage represents the valley inductor current and is compared to the OCP threshold. If the sensed phase voltage is lower than the OCP threshold, OCP will be triggered. Both UGATE and LGATE will go low, and the controller will enter the hiccup mode until the OCP condition is released. is a registered trademark of Richtek Technology Corporation. www.richtek.com 9 RT8120E/F LGATE Over Current Setting (LGOCS) Output Voltage Setting Over current threshold is externally programmed by adding a resistor (ROCSET) between LGATE and GND. Once VCC exceeds the POR threshold, an internal current source IOCSET flows through ROCSET. The voltage across ROCSET is stored as the over current protection threshold VOCSET. After that, the current source is switched off. ROCSET can be determined using the following equation : IVALLEY x RLGDS(ON) ROCSET = IOCSET The RT8120E/F allows the output voltage of the DC-DC converter to be adjusted from 0.8V (option for 0.6V) to 85% of VIN via an external resistor divider. It will try to maintain the feedback pin at internal reference voltage (0.8V, with option for 0.6V). where IVALLEY represents the desired inductor OCP trip current (valley inductor current). If ROCSET is not present, there is no current path for IOCSET to build the OCP threshold. In this situation, the OCP threshold is internally preset to 375mV (typical). Over Voltage Protection The feedback voltage at FB pin is continuously monitored for over voltage protection. When OVP is tripped, UGATE will go low and LGATE will to high to discharge the output capacitor. RT8120E/F provides over voltage protection whenever soft-start completes or not. Over voltage protection has two operating conditions : before VCC POR completes and after VCC POR completes. Each condition is described as follows. Before VCC POR completes, the typical OVP threshold is 162.5% of the internal reference voltage VREF. RT8120E/ F provides non-latched OVP before soft start completes. The controller will return to normal operation if over voltage condition is removed. After VCC POR completes, however, the OVP threshold is typically raised to 125% of VREF. RT8120E/F provides latched OVP, which means UGATE will to low and LGATE will go high. Under this condition, the controller can only be reset if VCC POR is toggled. Under Voltage Protection (UVP) The voltage on the FB pin is monitored for under voltage protection. If the FB voltage is lower than the UVP threshold (typically 75% x VREF) during normal operation, UVP will be triggered. When the UVP is triggered, both UGATE and LGATE go low. The controller enters hiccup mode until the UVP condition is removed. Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 10 VOUT RFB1 FB RFB2 Figure 1. Output Voltage Setting According to the resistor divider network above, the output voltage is set as :   R VOUT = VREF x  1 + FB1  R  FB2  MOSFET Drivers The RT8120E/F integrates high current gate drivers for the two N-MOSFETs to obtain high efficiency power conversion in synchronous buck topology. A dead time is used to prevent crossover conduction for the high side and low side MOSFETs. Because both gate signals are off during dead time, the inductor current freewheels through the body diode of the low side MOSFET. The freewheeling current and the forward voltage of the body diode contribute to power loss. The RT8120E/F employs constant dead time control scheme to ensure safe operation without sacrificing efficiency. Furthermore, elaborate logic circuit is implemented to prevent cross conduction. For high output current applications, two or more power MOSFETs are usually paralleled to reduce RDS(ON). The gate driver needs to provide more current to switch on/off these paralleled MOSFETs. Gate driver with lower source/ sink current capability result in longer rising/ falling time in gate signals, and therefore higher switching loss. The RT8120E/F embeds high current gate drivers to obtain high efficiency power conversion. The embedded drivers contribute to the majority of the power dissipation of the controller. Therefore, SOP package is chosen for its power dissipation rating. If no gate resistor is used, the power dissipation of the controller can be approximately calculated using the following equation : is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F PDRIVER = fSW x (QG x VBOOT + QG_LOW SIDE x VDRIVER_LOW SIDE ) where VBOOT represents the voltage across the bootstrap capacitor and fSW is the switching frequency. It is important to ensure the package can dissipate the switching loss and have enough room for safe operation. Inductor Selection The inductor plays an importance role in step-down converters because it stores the energy from the input power rail and then releases the energy to the load. From the viewpoint of efficiency, the dc resistance (DCR) of the inductor should be as small as possible to minimize the conduction loss. In addition, the inductor covers a significant proportion of the board space, so its size is also important. Low profile inductors can save board space especially when the height has a limitation. However, low DCR and low profile inductors are usually cost ineffective. Additionally, larger inductance results in lower ripple current, which translates into the lower power loss. However, the inductor current rising time increases with inductance value. This means the transient response will be slower. Therefore, the inductor design is a trade-off between performance, size and cost. In general, inductance is chosen such that the ripple current ranges between 20% to 40% of the full load current. The inductance can be calculated using the following equation : L(MIN) = VIN  VOUT V x OUT fSW x k x IOUT_RATED VIN where k is the ratio between inductor ripple current and rated output current. Input Capacitor Selection Voltage rating and current rating are the key parameters when selecting an input capacitor. Conservatively speaking, an input capacitor should have a voltage rating 1.5 times greater than the maximum input voltage to be considered a safe design. The input capacitor is used to supply the input RMS current, which can be approximately calculated using the following equation : Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021   VOUT V x  1  OUT  VIN VIN   The next step is to select a proper capacitor for the RMS current rating. Using more than one capacitor with low Equivalent Series Resistance (ESR) in parallel to form a capacitor bank is a good design. Placing the ceramic capacitor close to the drain of the high side MOSFET can also be helpful in reducing the input voltage ripple at heavy load. I RMS = IOUT x Output Capacitor Selection The output capacitor and the inductor form a low-pass filter in the buck topology. In steady state condition, the ripple current flowing into/out of the capacitor results in voltage ripple. The output voltage ripples contains two components, ΔVOUT_ESR and ΔVOUT_C. VOUT_ESR = IL x ESR VOUT_C = IL x 1 8 x COUT x fSW When load transient occurs, the output capacitor supplies the load current before controller can respond. Therefore, the ESR will dominate the output voltage sag during load transient. The output voltage sag can be calculated using the following equation : VOUT_SAG = ESR x ΔIOUT For a given output voltage sag specification, the ESR value can be determined. Another parameter that has influence on the output voltage sag is the equivalent series inductance (ESL). The rapid change in load current results in di/dt during transient. Therefore ESL contributes to part of the voltage sag. Using a capacitor with low ESL will obtain better transient performance. Generally, using several capacitors connected in parallel will also have better transient performance than just one single capacitor with the same total ESR. Unlike electrolytic capacitors, the ceramic capacitor has relatively low ESR and can reduce the voltage deviation during load transient. However, the ceramic capacitor can only provide low capacitance value. Therefore, it is suggested to use a mixed combination of electrolytic capacitor and ceramic capacitor for achieving better transient performance. is a registered trademark of Richtek Technology Corporation. www.richtek.com 11 RT8120E/F MOSFET Selection regulation with fast transient response. The RT8120E/F uses a high gain operational transconductance amplifier (EOTA) as the error amplifier. As Figure 2 shows, the EOTA works as the voltage controlled current source. The calculation of the transconductance is shown below : I GM = OUT , where VM =  VIN+    VIN  VM The majority of power loss in the step-down power conversion is due to the loss in the power MOSFETs. For low voltage high current applications, the duty cycle of the high side MOSFET is small. Therefore, the switching loss of the high side MOSFET is of concern. Power MOSFETs with lower total gate charge are preferred in such kind of application. However, the small duty cycle means the low side MOSFET is on for most of the switching cycle. Therefore, the conduction loss tends to dominate the total power loss of the converter. To improve the overall efficiency, MOSFETs with low RDS(ON) are preferred in the circuit design. In some cases, more than one MOSFET are connected in parallel to further decrease the on-state resistance. However, this depends on the low side MOSFET driver capability and the budget. and VCOMP = IOUT x ZOUT Figure 3 shows a typical buck control loop using a Type II compensator. The control loop consists of the power stage, PWM comparator and a compensator. The PWM comparator compares VCOMP with the oscillator (OSC) sawtooth wave to provide a Pulse-Width Modulated (PWM) with an amplitude of VIN at the PHASE node. The PWM wave is smoothed by the output filter LOUT and COUT. The output voltage (VOUT) is sensed and fed to the inverting input of the error amplifier. It is recommended to bypass low side MOSFET with a snubber circuit (R = 1Ω, C = 3.3nF). The modulator transfer function is the small-signal transfer function of VOUT/VCOMP (output voltage over the error amplifier output). This transfer function is dominated by a DC gain, a double pole, and an ESR zero as shown in Figure 4. Compensation Network Design The RT8120E/F is a voltage mode controller and requires external compensation to have an accurate output voltage VIN+ + VIN- - IOUT GM VCOMP ZOUT Figure 2. Operational Transconductance Amplifier, EOTA VIN PWM Comparator UGATE Q1 + Driver Logic - VOSC LOUT PAHSE VOUT LGATE Q2 FB RFB1 COUT VREF + GM - RFB2 COMP VCOMP CC CP RC Figure 3. Typical Voltage Mode Buck Converter Control Loop Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 12 is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F 80 80 Loop Gain 60 fP1 f LC 40 40 Gain (dB) 20 0 Compensation Gain f Z1 fP2 0 -20 Modulator Gain fESR -40-40 -60-60 10Hz 10vdb(vo) 100Hz vdb(comp2)100 vdb(lo) 1.0KHz 10KHz 1k 10k Frequency (Hz) Frequency 100KHz 100k 1.0MHz 1M Figure 4. Typical Bode Plot of a Voltage Mode Buck Converter To determine the 0dB crossing frequency (fC, control loop bandwidth) is the first step of compensator design. Usually, the fC is set to 0.1 to 0.3 times the switching frequency. The second step is to calculate the open loop modulator gain and find out the gain loss at fC. The third step is to design a compensator gain that can compensate the modulator gain loss at fC. The final step is to design fZ1 and fP2 to allow the loop sufficient phase margin. fZ1 is designed to cancel one of the double poles of modulator. Usually, place fZ1 before fLC. fP2 is usually placed below the switching frequency (typically, 0.5 to 1 times the switching frequency) to cancel high frequency noise. Thermal Considerations The DC gain of the modulator is the input voltage (VIN) divided by the peak-to-peak oscillator voltage VOSC. VIN GainMODULATOR = VOSC The output LC filter introduces a double pole, 40dB/decade gain slope above its corner resonant frequency, and a total phase lag of 180 degrees. The resonant frequency of the LC filter is expressed as : 1 fLC = 2 LOUT x COUT The ESR zero is contributed by the ESR associated with the output capacitance. Note that this requires that the output capacitor should have enough ESR to satisfy stability requirements. The ESR zero of the output capacitor is expressed as follows : 1 fESR = 2 x COUT x ESR The goal of the compensation network is to provide adequate phase margin (usually greater than 45 degrees) and the highest bandwidth (0dB crossing frequency). It is also recommended to manipulate loop frequency response that its gain crosses over 0dB at a slope of −20dB/dec. According to Figure 4, the compensation network frequency is as below : fP1 = 0 1  CC x Cp  2 x R C x    CC + CP  1 fZ1 = 2 x RC x CC fP2 = Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021 For continuous operation, do not exceed absolute maximum junction temperature. The maximum power dissipation depends on the thermal resistance of the IC package, PCB layout, rate of surrounding airflow, and difference between junction and ambient temperature. The maximum power dissipation can be calculated by the following formula : PD(MAX) = (TJ(MAX) − TA ) / θJA Where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and θJA is the junction to ambient thermal resistance. For recommended operating condition specifications, the maximum junction temperature is 125°C. The junction to ambient thermal resistance, θJA, is layout dependent. For SOP-8 package, the thermal resistance, θJA, is 188°C/W on a standard JEDEC 51-7 four-layer thermal test board. For SOP-8 (Exposed Pad) package, the thermal resistance, θJA, is 30.6°C/W on a standard JEDEC 51-7 four-layer thermal test board. The maximum power dissipation at TA = 25°C can be calculated by the following formulas : PD(MAX) = (125°C − 25°C ) / (188°C/W) = 0.53W for SOP-8 package PD(MAX) = (125°C − 25°C ) / (30.6°C/W) = 3.26W for SOP-8 (Exposed Pad) package is a registered trademark of Richtek Technology Corporation. www.richtek.com 13 RT8120E/F The maximum power dissipation depends on operating ambient temperature for fixed T J(MAX) and thermal resistance, θJA. The derating curves in Figure 5 allow the designer to see the effect of rising ambient temperature on the maximum power dissipation. Maximum Power Dissipation (W) 3.6  Minimize the trace length between the power MOSFETs and its drivers. Since the drivers use short, high current pulses to drive the power MOSFETs, the driving traces should be as short and wide as possible to reduce the trace inductance. This is especially true for the low side MOSFET, since this can reduce the possibility of the shoot through. Four-Layer PCB 3.2 SOP-8 (Exposed Pad) 2.8 2.4  Provide enough copper area around the power MOSFETs 2.0 and the inductors to aid in heat sinking. Using thick copper PCB can also reduce the resistance and inductance to improve efficiency. 1.6 1.2 0.8 SOP-8  The bank of the output capacitor should be placed physically close to the load. This can minimize the impedance seen by the load and then improve the transient response.  Placing all the high frequency decoupling ceramic capacitors close to their decoupling targets.  Small-signal components should be located as close as possible to the IC. The small signal components include the feedback components, current sensing components, compensation components, function setting components and any bypass capacitors. 0.4 0.0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 5. Derating Curve of Maximum Power Dissipation Layout Considerations Layout planning plays a critical role in modern highfrequency switching converter design. Circuit boards with good layout can help the IC function properly and achieve low losses, low switching noise, and stable operation with improved performance. Without a good layout, the PCB could radiate excessive noise, causing noise-induced IC problems and converter instability. The following guidelines is suggested have better IC performance. These components belong to the high impedance circuit loop and are inherently sensitive to noise pick-up. Therefore, they must be located close to their respective controller pins and away from the noisy switching nodes.   The power components should be placed first. Keep the connection between power components as short as possible. A multi-layer PCB design is recommended. Make use of one single layer as the power ground and have a separate control signal ground as the reference of all signals.  Input bulk capacitors should be placed close to the drain of the high side MOSFET and the source of the low side MOSFET.  Place the VCC bypass capacitor as close as possible to the RT8120E/F. Copyright © 2021 Richtek Technology Corporation. All rights reserved. www.richtek.com 14 is a registered trademark of Richtek Technology Corporation. DS8120E/F-03 September 2021 RT8120E/F Outline Dimension H A M J B F C I D Dimensions In Millimeters Dimensions In Inches Symbol Min Max Min Max A 4.801 5.004 0.189 0.197 B 3.810 3.988 0.150 0.157 C 1.346 1.753 0.053 0.069 D 0.330 0.508 0.013 0.020 F 1.194 1.346 0.047 0.053 H 0.170 0.254 0.007 0.010 I 0.050 0.254 0.002 0.010 J 5.791 6.200 0.228 0.244 M 0.400 1.270 0.016 0.050 8-Lead SOP Plastic Package Copyright © 2021 Richtek Technology Corporation. All rights reserved. DS8120E/F-03 September 2021 is a registered trademark of Richtek Technology Corporation. www.richtek.com 15 RT8120E/F H A M EXPOSED THERMAL PAD (Bottom of Package) Y J X B F C I D Dimensions In Millimeters Dimensions In Inches Symbol Min Max Min Max A 4.801 5.004 0.189 0.197 B 3.810 4.000 0.150 0.157 C 1.346 1.753 0.053 0.069 D 0.330 0.510 0.013 0.020 F 1.194 1.346 0.047 0.053 H 0.170 0.254 0.007 0.010 I 0.000 0.152 0.000 0.006 J 5.791 6.200 0.228 0.244 M 0.406 1.270 0.016 0.050 X 2.000 2.300 0.079 0.091 Y 2.000 2.300 0.079 0.091 X 2.100 2.500 0.083 0.098 Y 3.000 3.500 0.118 0.138 Option 1 Option 2 8-Lead SOP (Exposed Pad) Plastic Package Richtek Technology Corporation 14F, No. 8, Tai Yuen 1st Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries. www.richtek.com 16 DS8120E/F-03 September 2021
RT8120FGSP 价格&库存

很抱歉,暂时无法提供与“RT8120FGSP”相匹配的价格&库存,您可以联系我们找货

免费人工找货