RT9194GE

RT9194 Low-Dropout Linear Regulator Controller with PGOOD Indication General Description Features The RT9194 is a low-dropout voltage regulator controller with a specific PGOOD indicating scheme, it acts as a power supervisor of the power regulated. The part could drive an external N-MOSFET for various applications accordingly; especially, the part is operated with VCC power ranging from 4.5V to 13.5V. With such a topology, it's with advantages of flexible and cost-effective. The part comes to a small footprint package of SOT-23-6. z z z z z z z z Ordering Information z Package Type E : SOT-23-6 z Lead Plating System P : Pb Free G : Green (Halogen Free and Pb Free) z z ` Special Designed for Intel ® Grantsdale platform FSB_VTT power regulation Processor Power-Up Sequening Notebook and laptop PC Other Power regulation with Power Good indication. Pin Configurations Richtek products are : ` Quick Transient Response Power Good Indicator with Delay Enable Control Compliant with Intel “Grantsdale Chipset Platform Design Guide” Specification Small Footprint Package SOT-23-6 RoHS Compliant and 100% Lead (Pb)-Free Applications RT9194 Note : 4.5V to 13.5V Operation Voltage High Accuracy ± 2% 0.8V Voltage Reference RoHS compliant and compatible with the current require- (TOP VIEW) ments of IPC/JEDEC J-STD-020. VCC DRI PGOOD Suitable for use in SnPb or Pb-free soldering processes. 6 Marking Information 5 4 2 3 EN GND FB For marking information, contact our sales representative directly or through a Richtek distributor located in your area. SOT-23-6 Typical Application Circuit VCC Chip Enable 1 EN 2 3 GND VCC RT9194 DRI PGOOD FB 6 VIN Ccc 5 4 CIN Q1 RPGOOD PGOOD VOUT R1 COUT VOUT = 0.8x[(R1+R2)/R2] DS9194-10 April 2011 R2 www.richtek.com 1 RT9194 Test Circuit VCC VIN 12V Ccc 1uF Chip Enable EN GND CIN 100uF VCC RT9194 Q1 PHD3055 DRI 100k FB VOUT PGOOD RPGOOD PGOOD VOUT COUT 100uF R1 1k R1 + R2 = 0.8 × R2 R2 2k Figure 1. Typical Test Circuit VCC 12V Ccc 1uF Chip Enable 5V EN GND VFB FB VCC RT9194 DRI A VDRI PGOOD CFB VFB = 1V for current sink at DRI VFB = 0.6V for current source at DRI Figure 2. DRI Source/Sink Current Test Circuit www.richtek.com 2 DS9194-10 April 2011 RT9194 Functional Pin Description Pin No. Pin Name Pin Function 1 EN Chip Enable (Active High) 2 GND Ground 3 FB Output Voltage Feedback 4 PGOOD Power Good Open Drain Output 5 DRI Driver Output 6 VCC Power Supply Input Function Block Diagram EN VCC Reference 0.8V Voltage 0.7V PGOOD Driver DRI + - 3ms Delay + FB GND DS9194-10 April 2011 www.richtek.com 3 RT9194 Absolute Maximum Ratings z z z z z z z z z (Note 1) Supply Input Voltage, VCC ----------------------------------------------------------------------------------------- 15V Enable Voltage ------------------------------------------------------------------------------------------------------- 7V Power Good Output Voltage --------------------------------------------------------------------------------------- 7V Power Dissipation, PD @ TA = 25°C SOT-23-6 --------------------------------------------------------------------------------------------------------------- 0.4W Package Thermal Resistance SOT-23-6, θJA --------------------------------------------------------------------------------------------------------- 250°C/W Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------------- 260°C Junction Temperature ----------------------------------------------------------------------------------------------- 150°C Storage Temperature Range --------------------------------------------------------------------------------------- −65°C to 150°C ESD Susceptibility (Note 2) HBM (Human Body Mode) ----------------------------------------------------------------------------------------- 2kV MM (Machine Mode) ------------------------------------------------------------------------------------------------ 200V Recommended Operating Conditions z z z z (Note 3) Supply Input Voltage, VCC ----------------------------------------------------------------------------------------Enable Voltage ------------------------------------------------------------------------------------------------------Junction Temperature Range -------------------------------------------------------------------------------------Ambient Temperature Range -------------------------------------------------------------------------------------- 4.5V to 13.5V 0V to 5.5V −40°C to 125°C −40°C to 85°C Electrical Characteristics (VCC = 5V/12V, TA = 25° C, unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit V CC Operation Voltage Range VCC input range 4.5 -- 13.5 V POR Threshold VCC rising 4.0 4.2 4.5 V POR Hysteresis VCC falling -- 0.2 -- V V CC Supply Current VCC = 12V -- 0.3 0.8 mA Driver Source Current VCC = 12V, V DRI = 6V 5 -- -- mA Driver Sink Current VCC = 12V, V DRI = 6V 5 -- -- mA Reference Voltage (VFB) VCC = 12V, V DRI = 5V 0.784 0.8 0.816 V Reference Line Regulation (VFB ) VCC = 4.5V to 15V -- 3 6 mV Amplifier Voltage Gain VCC = 12V, no load -- 70 -- dB PSRR at 100Hz, No Load VCC = 12V, no load 50 -- -- dB Rising Threshold VCC = 12V -- 90 -- % Hysteresis VCC = 12V -- 15 -- % Sink Capability VCC = 12V @ 1mA -- 0.2 0.4 V Delay Time VCC = 12V 1 3 10 ms Falling Delay VCC = 12V -- 15 -- us Power Good To be Continued www.richtek.com 4 DS9194-10 April 2011 RT9194 Parameter Test Conditions Min Typ Max Unit Chip Enable EN Rising Threshold VCC = 12V -- 0.7 -- V EN Hysteresis VCC = 12V -- 30 -- mV Standby Current VCC = 12V, VEN = 0V -- -- 5 uA Note 1. Stresses listed as the above "Absolute Maximum Ratings" may cause permanent damage to the device. These are for stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may remain possibility to affect device reliability. Note 2. Devices are ESD sensitive. Handling precaution recommended. Note 3. The device is not guaranteed to function outside its operating conditions. DS9194-10 April 2011 www.richtek.com 5 RT9194 Typical Operating Characteristics Feedback Voltage vs. Temperature Quiescent Current vs. Temperature 0.48 0.47 0.46 VIN = 1.5V, VCC = 12V, RPGOOD = 100k CIN = COUT = 100uF, R1 = 1k, R2 = 2k Feedback Voltage (V) Refer to Test Circuit Figure 1 0.85 0.8 0.75 VIN = 1.5V, VCC = 12V, RPGOOD = 100k CIN = COUT = 100uF, R1 = 1k, R2 = 2k 0.7 0.45 -50 -25 0 25 50 75 100 -50 125 -25 0 75 100 125 DRI Sink Current vs. Temperature DRI Source Current vs. Temperature 60 50 45 40 Refer to Test Circuit Figure 2 55 DRI Sink Current (mA) 30 Refer to Test Circuit Figure 2 DRI Source Current (mA) 50 Temperature (°C) Temperature (°C) 27 24 21 18 15 VFB = 1V, VCC = 12V, VDRI = 6V VFB = 0.6V, VCC = 12V, VDRI = 6V 35 12 -50 -25 0 25 50 75 100 125 -50 -25 0 Temperature (°C) 25 50 75 100 125 Temperature (°C) PGOOD Delay Time vs. Temperature Sink Current vs. DRI Voltage 4 20 15 10 5 PGOOD Delay Time (ms) Refer to Test Circuit Figure 2 25 Sink Current (mA) 25 3.5 VIN = 1.5V, VCC = 12V RPGOOD = 100k R1 = 1k, R2 = 2k Refer to Test Circuit Figure 1 Quiescent Current (mA) 0.49 Refer to Test Circuit Figure 1 0.9 0.5 3 2.5 2 TA = 25°C 1.5 0 0 0.5 1 1.5 2 DRI Voltage (V) www.richtek.com 6 2.5 3 -50 -25 0 25 50 75 100 125 Temperature (°C) DS9194-10 April 2011 RT9194 PGOOD Delay Time VCC = 12V, ILOAD = 1A CIN = COUT = 100uF Refer to Test Circuit Figure 1 VCC = 12V, CIN = COUT = 100uF, ILOAD = 100mA V OUT V PGOOD VEN (V) V OUT ILoad (A) V PGOOD VEN (V) Time (500us/Div) Time (500us/Div) PGOOD Off VEN (V) Enable Threshold Voltage (V) VPGOOD Refer to Test Circuit Figure 1 ILoad (A) 1 VIN = 1.5V, VCC = 12V, RPGOOD = 100kΩ CIN = COUT = 100uF, R1 = 1k, R2 = 2k 0.95 0.9 Turn on 0.85 0.8 Turn off 0.75 0.7 0.65 Refer to Test Circuit Figure 1 Enable Threshold Voltage vs. Temperature VCC = 12V CIN = COUT = 100uF V OUT Refer to Test Circuit Figure 1 PGOOD Delay Time 0.6 -50 Time (50us/Div) -25 0 25 50 75 100 125 Temperature (°C) -20 5 0 Time (250us/Div) DS9194-10 April 2011 VIN = 1.5V to 2.5V, ILOAD = 100mA CIN = 2.2uF, COUT = 100uF 10 0 -10 2.5 1.5 Time (100us/Div) www.richtek.com 7 Refer to Test Circuit Figure 1 0 FB Voltage Deviation (mV) 20 Input Voltage Deviation (V) VIN = 2.5V, VOUT = 1.2V CIN = COUT = 100uF Line Transient Response Refer to Test Circuit Figure 1 Load Current(A) FB Voltage Deviation (mV) Load Transient Response RT9194 Application Information Capacitors Selection Careful selection of the external capacitors for RT9194 is highly recommended in order to remain high stability and performance. Regarding the supply voltage capacitor, connecting a capacitor which is 1μF between VCC and ground is a must. The capacitor improves the supply voltage stability to provide chip normally operating. Regarding the input capacitor, connecting a capacitor which 100μF between VIN and ground is recommended to increase stability. With large value of capacitance could result in better performance for both PSRR and line transient response. the output voltage decay rate. Drive the EN pin high to turn on the device again. Under Voltage Protection RT9194 equips the VOUT under-voltage (UV) protection function. The UV protection circuits will start monitoring the power status after the PGOOD pin goes high. If the output voltage drops to below 75% of its setting value, the PGOOD and DRI pins will be pulled low and latch RT9194. The UV latch status will be released only when VCC or Enable pin goes low and returns high again, which will also cause RT9194 to re-activate. MOSFET Selection When driving external pass element, connecting a capacitor 100μF between V OUT and ground is recommended for stability. With larger capacitance can reduce noise and improve load transient response and PSRR. The RT9194 are designed to driver external N-Channel MOSFET pass element. MOSFET selection criteria include threshold voltage V GS (V TH ), maximum Output Voltage Setting The most critical specification is the MOSFET RDS(ON). Calculate the required RDS(ON) from the following formula: V − VOUT NMOSFET RDS(ON) = IN ILOAD For example, the MOSFET operate up to 2A when the input voltage is 1.5V and set the output voltage is 1.2V, R ON = (1.5V-1.2V) / 2A = 150mΩ, the MOSFET's RON have to select lower than 150mΩ. A Philip PHD3055E MOSFET with an RDS(ON) of 120mΩ(typ.) is a close match. The RT9194 develop a 0.8V reference voltage; especially suit for low voltage application. As shown in application circuit, the output voltage could easy set the output voltage by R1 & R2 divider resistor. Power Good Function The RT9194 has the power good function with delay. The power good output is an open drain output. Connect a 100kΩ pull up resistor to VOUT to obtain an output voltage. When the output voltage arrive 90% of normal value the power good will output voltage with 3ms delay time. When the output voltage falling arrive 75% of normal value the power good will turn off with less than 1ms delay time. But, there are two exceptions. One is the enable pull low the power good will turn off quickly. The second is the VCC falling arrive POR value (4V typ.) the power good also will turn off quickly. Chip Enable Operation Pull the EN pin low to drive the device into shutdown mode. During shutdown mode, the standby current drops to 5μA(MAX). The external capacitor and load current determine www.richtek.com 8 continuous drain current ID, on-resistance R DS(ON) ,maximum drain-to-source voltage VDS and package thermal resistance θ(JA). And carry on consider the thermal resistance from junction to ambient θ(JA) of the MOSFET's package. The power dissipation calculate by : PD = (VIN − VOUT) x ILOAD The thermal resistance from junction to ambient θ(JA) calculate by : (T − T ) θ(JA) = J A PD In this example, PD = (1.5V − 1.2V) x 2A = 0.6W. The PHD3055E's θ(JA) is 75°C/W for its D-PAK package, which translates to a 45°C temperature rise above ambient. The package provides exposed backsides that directly transfer heat to the PCB board. DS9194-10 April 2011 RT9194 PNP Transistor Selection The RT9194 could driver the PNP transistor to sink output current. PNP transistor selection criteria include DC current gain hFE, threshold voltage VEB, collector-emitter voltage VCE, maximum continues collector current IC, package thermal resistance θ(JA). For example, the PNP transistor operates sink current up to 0.5A when the input voltage is 1.5V and set the output voltage is 1.2V. As show in Figure 3. A KSB772 PNP transistor, the V CE = 1.2V, V BE = -1V, I C = 0.5A, IB = 0.5/160 ≥ 3.125mA, when the DRI pin voltage is 0.2V could sink 6.8mA(MAX) is a close match. Sink Current vs. DRI Voltage 25 VIN VCC VCC PGOOD GND Chip Enable EN Q1 DRI Ccc RT9194 20 CIN RPGOOD VOUT FB R1 Q2 COUT Sink Current (mA) PGOOD 15 10 5 R2 TA = 25°C 0 0 Figure 3 0.5 1 1.5 2 2.5 3 DRI Voltage (V) Figure 4 Layout Considerations There are three critical layout considerations. One is the divider resistors should be located to RT9194 as possible to avoid inducing any noise. The second is capacitors place. The CIN and COUT have to put at near the NMOS for improve performance. The third is the copper area for pass element. We have to consider when the pass element operating under high power situation that could rise the junction temperature. In addition to the package thermal resistance limit, we could add the copper area to improve the power dissipation. As show in Figure 5 and Figure 6. VIN VIN PGOOD CIN + VCC VCC GND Chip Enable EN Q1 DRI Ccc PGOOD RT9194 FB GND RPGOOD VOUT PGOOD VCC R1 VOUT + COUT FB EN + R2 GND Figure 5 DS9194-10 April 2011 Figure 6 www.richtek.com 9 RT9194 Outline Dimension H D L C B b A A1 e Dimensions In Millimeters Dimensions In Inches Symbol Min Max Min Max A 0.889 1.295 0.031 0.051 A1 0.000 0.152 0.000 0.006 B 1.397 1.803 0.055 0.071 b 0.250 0.560 0.010 0.022 C 2.591 2.997 0.102 0.118 D 2.692 3.099 0.106 0.122 e 0.838 1.041 0.033 0.041 H 0.080 0.254 0.003 0.010 L 0.300 0.610 0.012 0.024 SOT-23-6 Surface Mount Package Richtek Technology Corporation Richtek Technology Corporation Headquarter Taipei Office (Marketing) 5F, No. 20, Taiyuen Street, Chupei City 5F, No. 95, Minchiuan Road, Hsintien City Hsinchu, Taiwan, R.O.C. Taipei County, Taiwan, R.O.C. Tel: (8863)5526789 Fax: (8863)5526611 Tel: (8862)86672399 Fax: (8862)86672377 Email: marketing@richtek.com Information that is provided by Richtek Technology Corporation is believed to be accurate and reliable. Richtek reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. No third party intellectual property infringement of the applications should be guaranteed by users when integrating Richtek products into any application. No legal responsibility for any said applications is assumed by Richtek. www.richtek.com 10 DS9194-10 April 2011