R1202x Series
STEP-UP DC/DC CONVERTER with SHUTDOWN FUNCTION
NO.EA-255-170915
OUTLINE
The R1202x Series are CMOS-based PWM step-up DC/DC converter ICs with low supply current.
Each of these ICs consists of an NMOS FET, NPN transistor, an oscillator, a PWM comparator, a voltage
reference unit, an error amplifier, a current limit circuit, an under voltage lockout circuit (UVLO), an over-voltage
protection circuit (OVP), a soft-start circuit, a Maxduty limit circuit, and a thermal shutdown protection circuit. By
simply using an inductor, a resistor, and capacitors as external components, a high-efficiency step-up DC/DC
converter can be easily configured. At the standby mode, a rectifier transistor can separate the output from the
input.
The R1202x Series include a thermal shut-down circuit and an under-voltage lockout circuit (UVLO) which
separate the output from the input to shut down the current when the overheat caused when the output is connected
to the Gnd is detected and also during the UVLO detection. As other protection functions, the R1202x Series
contain a cycle by cycle current limit circuit that limits the Lx peak current, and an over-voltage protection circuit
(OVP) that detects the output overvoltage.
The R1202x Series offer three versions: the R1202xxxxA/B versions, which are optimized for constant-voltage
power supply and the R1202xxxxD version, which is optimized to drive serial white LEDs with constant current.
While the R1202xxxxA version discharges the VOUT output to 0V at the shutdown, the R1202xxxxB version doesn’t.
The brightness of the white LEDs can be adjusted quickly by applying a PWM signal (200Hz to 300kHz) to the CE
pin.
The R1202x Series are available in DFN1616-6B and TSOT-23-6 packages.
FEATURES
• Input Voltage Range ......................................... 2.3V to 5.5V (R1202xxxxA/B)
1.8V to 5.5V (R1202xxxxD)
• Supply Current ................................................. Typ. 800µA
• Standby Current ............................................... Max. 5µA
• Feedback Voltage ............................................ 1.0V±15mV (R1202xxxxA/B)
0.2V±10mV (R1202xxxxD)
• Oscillator Frequency ........................................ Typ. 1.2MHz
• Maximum Duty Cycle ....................................... Typ. 91%
• UVLO Function ............................................... Typ.2.0V (Hys.Typ.0.2V) (R1202xxxxA/B)
Typ.1.6V (Hys.Typ.0.1V) (R1202xxxxD)
• Lx Current Limit Function ................................. Select from 350mA, 700mA
• Over Voltage Protection ................................... Select from 14V-23V (Refer the Selection Guide)
• LED dimming control for R1202xxxxD ............. by external PWM signal (Frequency 200Hz to 300kHz)
• Thermal Protection Function .......................... Typ.150ºC(Hys.Typ.50ºC)
• Built-in Auto Discharge Function ...................... R1202xxxxA
• NMOS ON Resistance ..................................... 1.35Ω
• Packages ......................................................... DFN1616-6B, TSOT-23-6
APPLICATION
• Constant Voltage Power Source for portable equipment
• OLED power supply for portable equipment
• White LED Backlight for portable equipment
1
R1202x
NO.EA-255-170915
SELECTION GUIDE
The OVP threshold voltage, current limit, package and VFB/Auto discharge are user-selectable options.
Product Name
R1202Lyz1∗-TR
R1202Nyz3∗-TR-FE
Package
Quantity per Reel
Pb Free
Halogen Free
DFN1616-6B
5,000 pcs
Yes
Yes
TSOT-23-6
3,000 pcs
Yes
Yes
y
: Designation of OVP threshold
(3) 14V : R1202xxxxA/B/D
(4) 17V : R1202xxxxA/B
(5) 19V : R1202xxxxA/B
(6) 21V : R1202xxxxA/B
(7) 23V : R1202xxxxA/B/D
z
: Designation of current limit
(1) 350mA
(2) 700mA
∗
: Designation of VFB, auto discharge function
A
B
D
VFB
1.0V
1.0V
0.2V
Auto discharge
○
×
×
Auto-discharge function quickly lowers the output voltage to 0V, when the chip enable signal is switched from the active mode
to the standby mode, by releasing the electrical charge accumulated in the external capacitor.
2
R1202x
NO.EA-255-170915
BLOCK DIAGRAMS
R1202xxxxA
VIN
VFB
VOUT
UVLO
Err. Amp.
+
–
LX
PWM Comp.
+
–
R
Q
Switch
Control
Driver
Control
S
vref
Oscillator
Soft-start
Slope Compensation
OVP
Current
Limit
Current
sense
Thermal
Shutdown
∑
CE
CE
GND
R1202xxxxB
VIN
VFB
UVLO
Err. Amp.
+
–
PWM Comp.
+
–
R
Q
S
vref
Switch
Control
Driver
Control
Oscillator
Soft-start
VOUT
LX
Slope Compensation
OVP
Current
Limit
Current
sense
Thermal
Shutdown
∑
CE
CE
GND
3
R1202x
NO.EA-255-170915
R1202xxxxD
LX
VIN
VFB
UVLO
Err. Amp.
PWM Comp.
+
–
+
–
R
Q
S
vref
Switch
Control
Driver
Control
Oscillator
PWM
Cntrl
EN
Slope Compensation
Shutdown
delay
∑
OVP
Current
Limit
Current
sense
CE
CE
4
VOUT
GND
Thermal
Shutdown
R1202x
NO.EA-255-170915
PIN DESCRIPTIONS
• DFN1616-6B
Top View
6
5
• TSOT-23-6
Bottom View
4
4
5
6
2
3
3
2
4
6
∗
1
5
(mark side)
1
1
2
3
DFN1616-6B
Pin No
Symbol
Pin Description
1
CE
Chip Enable Pin ("H" Active)
2
VFB
Feedback Pin
3
LX
Switching Pin (Open Drain Output)
4
GND
5
VIN
6
VOUT
Ground Pin
Input Pin
Output Pin
∗) The tab is substrate level (GND). The tab is better to be connected to the GND, but leaving it open is also acceptable.
TSOT-23-6
Pin No
Symbol
Pin Description
1
CE
Chip Enable Pin ("H" Active)
2
VOUT
Output Pin
3
VIN
Input Pin
4
LX
Switching Pin (Open Drain Output)
5
GND
6
VFB
Ground Pin
Feedback Pin
5
R1202x
NO.EA-255-170915
ABSOLUTE MAXIMUM RATINGS
Symbol
(GND=0V)
Item
Rating
Unit
VIN
VIN Pin Voltage
-0.3 to 6.5
V
VCE
CE Pin Voltage
-0.3 to 6.5
V
VFB
VFB Pin Voltage
-0.3 to 6.5
V
VOUT
VOUT Pin Voltage
-0.3 to 25
V
VLX
LX Pin Voltage
-0.3 to 25
V
ILX
LX Pin Current
1000
mA
PD
Power Dissipation *
DFN1616-6B
(JEDEC STD. 51-7 Test Land Pattern)
2400
TSOT-23-6 (Standard Test Land Pattern)
460
mW
Tj
Junction Temperature Range
-40 to 125
°C
Tstg
Storage Temperature Range
-55 to 125
°C
∗) Refer to POWER DISSIPATION for detailed information.
ABSOLUTE MAXIMUM RATINGS
Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent damages
and may degrade the life time and safety for both device and system using the device in the field. The functional operation
at or over these absolute maximum ratings is not assured.
RECOMMENDED OPERATING CONDITIONS
Symbol
Item
Rating
VIN
Operating Input Voltage
Ta
Operating Temperature Range
Unit
R1202xxxxA/B
2.3 V to 5.5 V
V
R1202xxxxD
1.8 V to 5.5 V
V
−40 to 85
°C
RECOMMENDED OPERATING CONDITIONS
All of electronic equipment should be designed that the mounted semiconductor devices operate within the recommended
operating conditions. The semiconductor devices cannot operate normally over the recommended operating conditions,
even if when they are used over such conditions by momentary electronic noise or surge. And the semiconductor devices
may receive serious damage when they continue to operate over the recommended operating conditions.
6
R1202x
NO.EA-255-170915
ELECTRICAL CHARACTERISTICS
R1202x
Symbol
IDD
(Ta=25°C)
Item
Conditions
Min.
Typ.
Max.
Unit
Supply Current
VIN=5.5V , VFB=0V , LX at no load
0.8
1.2
mA
Istandby
Standby Current
VIN=5.5V , VCE=0V
1.0
5.0
µA
VUVLO1
UVLO Detect
Threshold Voltage
VIN falling
VUVLO2
UVLO Release Voltage
R1202xxxxA/B
1.9
2.0
2.1
V
R1202xxxxD
1.5
1.6
1.7
V
R1202xxxxA/B
VUVLO1
+0.2
2.3
V
R1202xxxxD
VUVLO1
+0.1
1.8
V
VIN rising
VCEH
CE Input Voltage "H"
VCEL
CE Input Voltage "L"
RCE
CE Pull Down
Resistance
VFB
VFB Voltage Accuracy
VCE=3.6V
VFB Voltage Temperature
Coefficient
VCE=3.6V, -40°C <
= Ta <
= 85°C
VFB Input Current
VIN=5.5V, VFB=0V or 5.5V
tstart
Soft-start Time
*R1202xxxxA/B
2.0
ms
RON
Driver ON Resistance
VCE=3.6V, ILX=100mA
1.35
Ω
IOFF
Driver Leakage Current
VLX=22V
ILIM
Driver Current Limit
VIN=3.6V
VF
NPN Forward Voltage
ILX=100mA
ISWOFF1
NPN Leakage Current 1
VOUT=22V, VLX=0V
10
µA
ISWOFF2
NPN Leakage Current 2
VOUT=0V, VLX=5.5V
3
µA
Oscillator Frequency
VIN=3.6V, VFB=0V
1400
kHz
∆VFB/∆Ta
IFB
fosc
VIN=5.5V
1.5
V
0.5
1200
kΩ
R1202xxxxA/B
0.985
1.000
1.015
R1202xxxxD
0.19
0.2
0.21
0.1
3.0
R1202xx1xx
250
350
450
R1202xx2xx
500
700
900
0.8
1000
1200
V
ppm/
°C
±150
-0.1
V
µA
µA
mA
V
7
R1202x
NO.EA-255-170915
(Ta=25ºC)
Symbol
Maxduty
VOVP1
Item
Maximum Duty Cycle
OVP Detect Voltage
Conditions
Min.
Typ.
86
91
R1202x3xxA/B/D
13.2
14
14.8
R1202x4xxA/B
16.2
17
17.8
R1202x5xxA/B
18.2
19
19.8
R1202x6xxA/B
20.2
21
21.8
R1202x7xxA/B/D
22.2
23
VOVP1
-1.1
VOVP1
-1.3
VOVP1
-1.4
VOVP1
-1.5
VOVP1
-1.7
23.8
VIN=3.6V, VFB=0V
VIN=3.6V,
VOUT rising
R1202x3xxA/B/D
R1202x4xxA/B
VOVP2
OVP Release Voltage
VIN=3.6V,
VOUT falling
R1202x5xxA/B
R1202x6xxA/B
R1202x7xxA/B/D
8
Max.
Unit
%
V
V
TTSD
Thermal Shutdown
Detect Temperature
VIN=3.6V
150
°C
TTSR
Thermal Shutdown
Release Temperature
VIN=3.6V
100
°C
R1202x
NO.EA-255-170915
THEORY OF OPERATION
Operation of Step-Up DC/DC Converter and Output Current
i2
IOUT
Diode
L
VIN
VOUT
i1
Lx Tr
CL
GND
Discontinuous mode
Continuous mode
ILmax
IL
IL
ILmax
ILmin
ILmin
topen
t
toff
ton
T=1/fosc
t
ton
toff
T=1/fosc
There are two operation modes of the step-up PWM control-DC/DC converter. That is the continuous mode and
discontinuous mode by the continuousness inductor.
When the transistor turns ON, the voltage of inductor L becomes equal to VIN voltage. The increase value of inductor
current (i1) will be
∆i1 = VIN × ton / L ........................................................................................................... Formula 1
As the step-up circuit, during the OFF time (when the transistor turns OFF) the voltage is continually supply from
the power supply. The decrease value of inductor current (i2) will be
∆i2 = (VOUT − VIN) × topen / L ........................................................................................... Formula 2
9
R1202x
NO.EA-255-170915
At the PWM control-method, the inductor current become continuously when topen=toff, the DC/DC converter
operate as the continuous mode.
In the continuous mode, the variation of current of i1 and i2 is same at regular condition.
VIN × ton / L = (VOUT - VIN) × toff / L ................................................................................... Formula 3
The duty at continuous mode will be
duty (%)= ton / (ton + toff) = (VOUT - VIN) / VOUT ................................................................. Formula 4
The average of inductor current at tf = toff will be
IL(Ave.) = VIN × ton / (2 × L) ............................................................................................ Formula 5
If the input voltage = output voltage, the IOUT will be
IOUT = VIN2 × ton / (2 × L × VOUT) ....................................................................................... Formula 6
If the IOUT value is large than above the calculated value (Formula 6), it will become the continuous mode, at this
status, the peak current (ILmax) of inductor will be
ILmax = IOUT × VOUT / VIN + VIN × ton / (2 × L) .................................................................... Formula 7
ILmax = IOUT × VOUT / VIN + VIN × T × (VOUT - VIN) / (2 × L × VOUT)....................................... Formula 8
The peak current value is larger than the IOUT value. In case of this, selecting the condition of the input and the
output and the external components by considering of ILmax value.
The explanation above is based on the ideal calculation, and the loss caused by LX switch and the external
components are not included.
The actual maximum output current will be between 50% and 80% by the above calculations. Especially, when the
IL is large or VIN is low, the loss of VIN is generated with on resistance of the switch. Moreover, it is necessary to
consider Vf of the diode (approximately 0.8V) about VOUT.
10
R1202x
NO.EA-255-170915
Soft-Start ( R1202xxxxA/B )
The output and referrence of the error amplifier start from 0V and the referrence gradually rises up to 1.0V.
After the softstart time (TSS), output voltage rise up to the setting voltage.
Protect Function
If the over current is detected, internal mosfet will turn-off soon. At the next operating period, mosfet will turn-on
again and continue to watch the current.
The UVLO function and the thermal shutdown function are turned off the NMOS-driver and NPN-transister when
the VIN decreases more than the UVLO detect threshold voltage or the inside of IC exceeds the thermal shutdown
detect temperature, and reset IC when the VIN rises more than the UVLO release voltage or the inside of IC falls
below the thermal shutdown release temperature, and restart the operation.
Shutdown
At standby mode, the output is completely separated from the input and shutdown by the NPN transistor of
internal IC. However, the leakage current is generated when the LX pin voltage is higher than VIN pin voltage at
standby mode.
R1202xxxxA (with auto discharge function): In the term of standby mode, the switch between VOUT to GND is
turned ON and output capacitor is discharged.
11
R1202x
NO.EA-255-170915
APPLICATION INFORMATION
Typical Applications
L1
10µH~22µH
L1
10µH~22µH
C1
1µF
C1
1µF
VIN
LX
CE
VOUT
C3
R2
GND
C2
1µF
R3
VIN
LX
CE
VOUT
GND
VFB
VFB
R1
R1202xxxxA/B
C2
0.22µF
R1
10Ω
R1202xxxxD
Selection of Inductor
The peak current of the inductor at normal mode can be estimated as the next formula when the efficiency is 80%.
ILmax = 1.25 × IOUT × VOUT / VIN + 0.5 × VIN × (VOUT - VIN) / (L × VOUT × fosc)
In the case of start-up or dimming control by CE pin, inductor transient current flows, and the peak current of it
must be equal or less than the current limit of the IC. The peak current should not beyond the rated current of
the inductor. The recommended inductance value is 10µH -22µH.
Table 1 Peak current value in each condition
VIN (V)
3
3
3
3
Condition
VOUT (V) IOUT (mA)
14
20
14
20
21
20
21
20
L (µH)
10
22
10
22
ILmax (mA)
215
160
280
225
Table 2 Recommended inductors
L (µH)
10
10
10
10
10
22
22
22
22
12
Part No.
LQH32CN100K53
LQH2MC100K02
VLF3010A-100
VLS252010-100
VLF403212MT-100M
LQH32CN220K53
LQH2MC220K02
VLF3010A-220
VLF504015MT-220M
Rated current (mA)
450
225
490
520
900
250
185
330
930
Size (mm)
3.2x2.5x1.55
2.0x1.6x0.9
2.8x2.6x0.9
2.5x2.0x1.0
4.0×3.2×1.2
3.2x2.5x1.55
2.0x1.6x0.9
2.8x2.6x0.9
5.0×4.0×1.5
R1202x
NO.EA-255-170915
Selection of Capacitor
Set 1µF or more value bypass capacitor C1 between VIN pin and GND pin as close as possible.
R1202xxxxA/R1202xxxxB
Set 1µF – 4.7µF or more capacitor C2 between VOUT and GND pin.
R1202xxxxD
Set 0.22µF or more capacitor C2 between VOUT and GND pin.
The rated voltage of C2 should be 25V or more.
Table 3 Recommended components for R1202xxxxA/R1202xxxxB
C1
C2
C3
R1
R2
R3
Rated voltage(V)
Part No.
6.3
25
25
CM105B105K06
GRM21BR11E105K
220pF
For VOUT Setting
For VOUT Setting
2kΩ
Table 4 Recommended components for R1202xxxxD
C1
C2
Rated voltage(V)
Part No.
6.3
25
CM105B105K06
GRM21BR11E224
External Components Setting
If the spike noise of VOUT may be large for R1202xxxxA/B, the spike noise may be picked into VFB pin and make
the operation unstable. In this case, use a R3 of the resistance value in the range from 1kΩ to 5kΩ to reduce a
noise level of VFB.
The Method of Output Voltage Setting (R1202xxxxA/B)
The output voltage (VOUT) can be calculated with divider resistors (R1 and R2) values as the following formula:
Output Voltage (VOUT) = VFB × (R1 + R2) / R1
The total value of R1 and R2 should be equal or less than 300kΩ. Make the VIN and GND line sufficient. The
large current flows through the VIN and GND line due to the switching. If this impedance (VIN and GND line) is
high, the internal voltage of the IC may shift by the switching current, and the operating may become unstable.
Moreover, when the built-in LX switch is turn OFF, the spike noise caused by the inductor may be generated. As
a result of this, recommendation voltage rating of capacitor (C2) value is equal 1.5 times larger or more than the
setting output voltage.
13
R1202x
NO.EA-255-170915
LED Current setting (R1202xxxxD)
When CE pin input is "H" (Duty=100%), LED current can be set with feedback resistor (R1)
ILED = VFB / R1
LED Dimming Control (R1202xxxxD)
The LED brightness can be controlled by inputting the PWM signal to the CE pin. If the CE pin input is "L" in the
fixed time (Typ.0.5ms), the IC becomes the standby mode and turns OFF LEDs.
The current of LEDs can be controlled by Duty of the PWM signal of the input CE pin. The current of LEDs when
High-Duty of the CE input is "Hduty" reaches the value as calculatable following formula.
ILED = Hduty × VFB / R1
The frequency of the PWM signal is using the range between 200Hz to 300kHz.
When controlling the LED brightness by the PWM signal of 20kHz or less, the increasing or decreasing of the
inductor current might be make a sounds in the hearable sound wave area. In that case, please use the PWM
signal in the high frequency area.
CE
Hduty
VFB
R1
Dimming control by CE pin input
14
R1202x
NO.EA-255-170915
TECHNICAL NOTES
Current Path on PCB
The current paths in an application circuit are shown in Fig. 1 and 2.
A current flows through the paths shown in Fig. 1 at the time of MOSFET-ON, and shown in Fig. 2 at the time of
MOSFET-OFF. In the paths pointed with red arrows in Fig. 2, current flows just in MOSFET-ON period or just in
MOSFET-OFF period. Parasitic impedance / inductance and the capacitance of these paths influence stability of
the system and cause noise outbreak. So please minimize this side effect. In addition, please shorten the wiring of
other current paths shown in Fig. 1 and 2 except for the paths of LED load.
Layout Guide for PCB
⋅
Please shorten the wiring of the input capacitor (C1) between VIN pin and GND pin of IC. The GND pin should be
connected to the strong GND plane.
⋅
The area of LX land pattern should be smaller.
⋅
Please put output capacitor (C2) close to the VOUT pin.
⋅
Please make the GND side of output capacitor (C2) close to the GND pin of IC.
MOSFET-ON
Load
Load
Fig. 1
Fig. 2
MOSFET-OFF
15
R1202x
NO.EA-255-170915
PCB Layout
・PKG:DFN1616-6 pin
R1202LxxxA/R1202LxxxB typical board layout
Topside
Backside
R1202LxxxD typical board layout
Topside
16
Backside
R1202x
NO.EA-255-170915
・PKG: TSOT-23-6 pin
R1202NxxxA/R1202NxxxB Typical Board Layout
Topside
Backside
R1202NxxxD Typical Board Layout
Topside
Backside
17
R1202x
NO.EA-255-170915
TYPICAL CHARACTERISTICS
1) Efficiency vs. Output Current (R1202N723A)
VOUT=10V, L=22µH (LQH32CN220K53)
90
90
85
85
80
80
Efficiency (%)
Efficiency (%)
VOUT=10V, L=10µH (LQH32CN100K53)
75
70
65
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
75
70
65
55
50
50
0
5
10
15
Output Current (mA)
0
20
85
85
80
80
Efficiency (%)
90
75
70
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
20
70
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
65
55
50
0
5
10
15
20
0
5
Output Current (mA)
85
85
80
80
Efficiency (%)
90
75
70
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
15
20
VOUT=20V, L=22µH (LQH32CN220K53)
90
65
10
Output Current (mA)
VOUT=20V, L=10µH (LQH32CN100K53)
Efficiency (%)
15
75
60
50
75
70
65
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
50
50
0
5
10
Output Current (mA)
18
10
VOUT=15V, L=22µH (LQH32CN220K53)
90
65
5
Output Current (mA)
VOUT=15V, L=10µH(LQH32CN100K53)
Efficiency (%)
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
15
20
0
5
10
Output Current (mA)
15
20
R1202x
NO.EA-255-170915
VOUT=20V, VIN=3.6V
85
Efficiency (%)
80
75
70
65
LQH32CN100k53L(3.2×2.5×1.55)
60
VLF3010AT-100MR33(3.0×2.8×1.0)
55
LQH2MCN100K02(2.0×1.6×0.9)
50
0
5
10
15
20
Output Current (mA)
2) Efficiency vs. Output Current (R1202N713D)
4LED, L=22µH (LQH32CN220K53)
90
90
85
85
80
80
Efficiency (%)
Efficiency (%)
4LED, L=10µH (LQH32CN100K53)
75
70
65
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
70
65
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
50
50
0
5
10
15
20
0
5
10
15
Output Current ILED (mA)
Output Current ILED (mA)
5LED, L=10µH (LQH32CN100K53)
5LED, L=22µH (LQH32CN220K53)
90
90
85
85
80
80
Efficiency (%)
Efficiency (%)
75
75
70
65
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
75
70
65
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
60
55
50
20
50
0
5
10
15
Output Current ILED (mA)
20
0
5
10
15
Output Current ILED (mA)
20
19
R1202x
NO.EA-255-170915
3) Efficiency vs. Output Current (R1202N713D)
5LED, VIN=3.6V
85
80
Efficiency (%)
75
70
65
60
LQH32CN100k53L(3.2×2.5×1.55)
VLF3010AT-100MR33(3.0×2.8×1.0)
LQH2MCN100K02(2.0×1.6×0.9)
55
50
0
5
10
15
20
Output Current ILED (mA)
4) Output Voltage vs. Output Current (R1202N723A)
VOUT=10V, L=10µH (LQH32CN100K53)
VOUT=10V, L=22µH (LQH32CN220K53)
10.8
10.8
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
10.4
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
10.6
Output Voltage (V)
Output Voltage (V)
10.6
10.2
10
10.4
10.2
10
9.8
9.8
9.6
9.6
0
50
100
150
200
0
50
Output Current (mA)
VOUT=15V, L=10µH (LQH32CN100K53)
200
16.4
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
15.6
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
16
Output Voltage (V)
16
Output Voltage (V)
150
VOUT=15V, L=22µH (LQH32CN220K53)
16.4
15.2
14.8
14.4
15.6
15.2
14.8
14.4
14
14
0
30
60
Output Current (mA)
20
100
Output Current (mA)
90
120
0
30
60
Output Current (mA)
90
120
R1202x
NO.EA-255-170915
VOUT=20V, L=10µH (LQH32CN100K53)
VOUT=20V, L=22µH (LQH32CN220K53)
21.2
21.2
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
20.6
Vin=3V
Vin=3.6V
Vin=4.2V
Vin=5V
20.9
Output Voltage (V)
Output Voltage (V)
20.9
20.3
20
19.7
20.6
20.3
20
19.7
19.4
19.4
0
25
50
75
0
100
20
Output Current (mA)
40
60
80
100
Output Current (mA)
VOUT=20V, VIN=3.6V
20.5
Output Voltage (V)
20.3
20.1
19.9
LQH32CN100k53L (3.2×2.5×1.55)
19.7
VLF3010AT-100MR33 (2.8×2.6×0.9)
LQH2MCN100K02 (2.0×1.6×0.9)
19.5
0
10
20
30
40
50
Output Current (mA)
5) Maxduty vs. ILED
6) OVP Output Waveform
R1202N713D
25
25
20
24
Output Voltage (V)
ILED (mA)
R1202N713D
15
10
200Hz
10kHz
5
0
20
40
60
Duty (%)
80
22
21
300kHz
0
23
100
20
-50
-30
-10
10
Time (ms)
30
50
21
R1202x
NO.EA-255-170915
7) Waveform (5LED)
R1202N713D (CE Freq=200Hz)
R1202N713D (CE Freq=10KHz)
5
-5
0
CE
0
Time (ms)
5
-5
-500
10
55
5
-5
0
-20
Diode Forward Voltage (V)
10
ILED
-5
0.5
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
-35
0
Time [µs]
-35
500
250
0.90
ILED (mA)
25
10
-0.5
0
Time (µs)
ILED
0.95
40
15
CE
-250
CE
8) Diode Forward Voltage vs. Temperature
20
-1
-20
Vout
R1202N713D (CE Freq=300KHz)
Vout
-5
0
-35
-5
10
5
ILED
-5
-10
25
10
-20
Vout
Output Voltage (V)
CE Voltage (V)
Output Voltage (V)
CE Voltage (V)
10
40
15
ILED (mA)
25
10
55
ILED (mA)
40
15
Output Voltage (V)
CE Voltage (V)
20
55
20
-40
1
-15
10
35
60
85
Temperature Ta (°C)
9) Standby Current vs. Temperature
10) Supply Current lin vs. Temperature
1000
900
Supplay Current Iin[µA]
Standby Current(uA)
1.0
0.8
0.6
0.4
0.2
700
600
500
400
300
200
100
0.0
0
-40
22
800
-15
10
35
60
Temperature Ta(°C)
85
-40
-15
10
35
Temperature Ta (°C)
60
85
R1202x
NO.EA-255-170915
11) UVLO Voltage vs. Temperature
R1202xxxxA/B
R1202xxxxD
2.25
1.75
1.70
2.15
UVLO Voltage(V)
UVLO Voltage (V)
2.20
2.10
2.05
2.00
1.95
1.65
1.60
1.55
1.50
1.90
1.85
1.45
-40
-15
10
35
60
85
-40
-15
10
Temperature Ta (°C)
35
60
85
Temperature Ta (°C)
12) VFB Voltage vs. Temperature
R1202xxxxA/B
R1202xxxxD
0.210
1.050
0.208
VFB Voltage (V)
VFB Voltage (V)
1.030
1.010
0.990
0.970
0.206
0.204
0.202
0.200
0.198
0.196
0.194
0.192
0.190
0.950
-40
-40
-15
10
35
Temperature Ta (°C)
60
-15
85
10
35
60
85
Temperature Ta (°C)
13) Switch ON Resistance RON vs. Temperature
14) OVP Voltage vs. Temperature
1.9
25
1.7
24
1.5
OVP Voltage (V)
Switch On Resistance RON (Ω)
R1202x7xxx
1.3
1.1
0.9
23
22
OVP Detect
21
OVP Release
20
0.7
0.5
19
-40
-15
10
35
Temperature Ta (°C)
60
85
-40
-15
10
35
60
85
Temperature Ta (°C)
23
R1202x
NO.EA-255-170915
15) Lx Limit Current vs. Temperature
R1202xx1xx
R1202xx2xx
900
500
Vin=3.6V
Lx Limit Current (mA)
Lx Limit Current (mA)
850
Vin=2.8V
450
Vin=5.5V
400
350
300
250
Vin=2.8V
Vin=3.6V
800
Vin=5.5V
750
700
650
600
550
500
200
-40
-15
10
35
60
-40
85
-15
16) Frequency Fosc vs. Temperature
85
100
Vin=1.8V
98
1300
Vin=3.6V
Vin=5.5V
96
MXDUTY (%)
1350
1250
1200
1150
Vin=1.8V
Vin=3.6V
Vin=5.5V
94
92
90
1100
88
1050
86
1000
84
-40
-15
10
35
60
85
Temperature Ta (°C)
-40
-15
10
200
180
Thermal Shutdown Detect
160
140
120
Thermal Shutdown Release
100
80
60
1.5
2
2.5
3
3.5 4
VIN (V)
4.5
35
Temperature Ta (°C)
18) Thermal Shutdown Detect / Release Temperature vs. Input Voltage
Temperature (°C)
60
17) MaxDuty vs. Temperature
1400
24
35
Temperature Ta (°C)
Temperature Ta (°C)
Frequency Fosc (kHz)
10
5
5.5
6
60
85
R1202x
NO.EA-255-170915
19) Inductor Current (output-GND short)
5LED(VIN=3V)
R1202N713D
5LED(VIN=3V)
R1202N723D
0.5
1
0.45
0.9
IL
Inductor Current (A)
Inductor Current (A)
0.4
0.35
0.3
0.25
0.2
0.15
IL
0.8
0.7
0.6
0.5
0.4
0.3
0.1
0.2
0.05
0.1
0
0
-5
-4
-3
-2
-1
0
1
2
3
4
5
-5
-4
-3
-2
TIme (µs)
1
2
3
4
5
5LED(VIN=3.6V)
R1202N723D
0.5
1
0.45
0.9
IL
0.4
0.8
0.35
0.7
Inductor Current (A)
Inductor Current (A)
0
TIme (µs)
5LED(VIN=3.6V)
R1202N713D
0.3
0.25
0.2
0.15
0.1
0.05
IL
0.6
0.5
0.4
0.3
0.2
0.1
0
0
-5
-4
-3
-2
-1 0 1
TIme (µs)
2
3
4
5
-5
-4
-3
-2
5LED(VIN=4.2V)
R1202N713D
-1 0 1
TIme (µs)
2
3
4
5
5LED(VIN=4.2V)
R1202N723D
0.5
1
0.45
0.9
IL
IL
0.8
Inductor Current (A)
0.4
Inductor Current (A)
-1
0.35
0.3
0.25
0.2
0.15
0.7
0.6
0.5
0.4
0.3
0.1
0.2
0.05
0.1
0
0
-5
-4
-3
-2
-1 0 1
TIme (µs)
2
3
4
5
-5
-4
-3
-2
-1 0 1
TIme (µs)
2
3
4
5
25
POWER DISSIPATION
DFN1616-6B
Ver. A
The power dissipation of the package is dependent on PCB material, layout, and environmental conditions.
The following conditions are used in this measurement.
Measurement Conditions
Item
Measurement Conditions (JEDEC STD. 51-7)
Environment
Mounting on Board (Wind Velocity = 0 m/s)
Board Material
Glass Cloth Epoxy Plastic (Four-Layer Board)
Board Dimensions
76.2 mm × 114.3 mm × 0.8 mm
Copper Ratio
1st Layer: Less than 95% of 50 mm Square
2nd, 3rd, 4th Layers: Approx. 100% of 50 mm Square
Through-holes
φ 0.2 mm × 15 pcs
Measurement Result
(Ta = 25°C, Tjmax = 125°C)
Item
Measurement Result
Power Dissipation
2400 mW
Thermal Resistance (θja)
θja = 41°C/W
Thermal Characterization Parameter (ψjt)
ψjt = 11°C/W
θja: Junction-to–ambient thermal resistance.
ψjt: Junction–to-top of package thermal characterization parameter.
2500
2400
Power Dissipation PD (mW)
2000
1500
1000
500
0
0
25
50
75 85
100
125
Ambient Temperature (°C)
Power Dissipation vs. Ambient Temperature
Measurement Board Pattern
i
PACKAGE DIMENSIONS
DFN1616-6B
Ver. A
1.30±0.05
INDEX
4
∗
0.4max.
3
0.1±0.05
6
0.25±0.05
0.05
(3X0.15)
B
1.60
X4
1.60
0.70±0.05
A
0.5
0.20±0.05
1
0.05 M AB
Bottom View
S
0.05 S
DFN1616-6B Package Dimensions (Unit: mm)
*
∗ The tab on the bottom of the package shown by blue circle is a substrate potential (GND). It is recommended that this
tab be connected to the ground plane pin on the board but it is possible to leave the tab floating.
i
POWER DISSIPATION
TSOT-23-6
Ver. A
The power dissipation of the package is dependent on PCB material, layout, and environmental conditions.
The following conditions are used in this measurement.
Measurement Conditions
Standard Test Land Pattern
Environment
Mounting on Board (Wind Velocity = 0 m/s)
Board Material
Glass Cloth Epoxy Plastic (Double-Sided Board)
Board Dimensions
40 mm × 40 mm × 1.6 mm
Top Side: Approx. 50%
Copper Ratio
Bottom Side: Approx. 50%
Through-holes
φ 0.5 mm × 44 pcs
Measurement Result
(Ta = 25°C, Tjmax = 125°C)
Standard Test Land Pattern
Power Dissipation
460 mW
θja = (125 − 25°C) / 0.46 W = 217°C/W
Thermal Resistance
θjc = 40°C/W
Power Dissipation PD (mW)
600
500
460
Standard Test Land Pattern
400
300
200
100
0
0
25
50
75 85 100
125
Ambient Temperature (°C)
Power Dissipation vs. Ambient Temperature
150
IC Mount Area (mm)
Measurement Board Pattern
i
PACKAGE DIMENSIONS
TSOT-23-6
+0.100
0.125-0.025
2.9±0.2
5
4
2
3
+0.10
0.4-0.05
0.85±0.10
0.95
S
0.12 M
0 ∼ 0.1
1
2.8±0.2
+0.2
1.6-0.1
6
0.4±0.2
Ver. A
0.10 S
TSOT-23-6 Package Dimensions (Unit: mm)
0∼15°
1. The products and the product specifications described in this document are subject to change or discontinuation of
production without notice for reasons such as improvement. Therefore, before deciding to use the products, please
refer to Ricoh sales representatives for the latest information thereon.
2. The materials in this document may not be copied or otherwise reproduced in whole or in part without prior written
consent of Ricoh.
3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise
taking out of your country the products or the technical information described herein.
4. The technical information described in this document shows typical characteristics of and example application circuits
for the products. The release of such information is not to be construed as a warranty of or a grant of license under
Ricoh's or any third party's intellectual property rights or any other rights.
5. The products listed in this document are intended and designed for use as general electronic components in standard
applications (office equipment, telecommunication equipment, measuring instruments, consumer electronic products,
amusement equipment etc.). Those customers intending to use a product in an application requiring extreme quality
and reliability, for example, in a highly specific application where the failure or misoperation of the product could result
in human injury or death (aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and
transportation equipment, combustion equipment, safety devices, life support system etc.) should first contact us.
6. We are making our continuous effort to improve the quality and reliability of our products, but semiconductor products
are likely to fail with certain probability. In order to prevent any injury to persons or damages to property resulting from
such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy
feature, fire containment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or
damage arising from misuse or inappropriate use of the products.
7. Anti-radiation design is not implemented in the products described in this document.
8. The X-ray exposure can influence functions and characteristics of the products. Confirm the product functions and
characteristics in the evaluation stage.
9. WLCSP products should be used in light shielded environments. The light exposure can influence functions and
characteristics of the products under operation or storage.
10. There can be variation in the marking when different AOI (Automated Optical Inspection) equipment is used. In the
case of recognizing the marking characteristic with AOI, please contact Ricoh sales or our distributor before attempting
to use AOI.
11. Please contact Ricoh sales representatives should you have any questions or comments concerning the products or
the technical information.
Halogen Free
Ricoh is committed to reducing the environmental loading materials in electrical devices
with a view to contributing to the protection of human health and the environment.
Ricoh has been providing RoHS compliant products since April 1, 2006 and Halogen-free products since
April 1, 2012.
http://www.e-devices.ricoh.co.jp/en/
Sales & Support Offices
RICOH ELECTRONIC DEVICES CO., LTD.
Higashi-Shinagawa Office (International Sales)
3-32-3, Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-8655, Japan
Phone: +81-3-5479-2857 Fax: +81-3-5479-0502
RICOH EUROPE (NETHERLANDS) B.V.
Semiconductor Support Centre
Prof. W.H. Keesomlaan 1, 1183 DJ Amstelveen, The Netherlands
Phone: +31-20-5474-309
RICOH INTERNATIONAL B.V. - German Branch
Semiconductor Sales and Support Centre
Oberrather Strasse 6, 40472 Düsseldorf, Germany
Phone: +49-211-6546-0
RICOH ELECTRONIC DEVICES KOREA CO., LTD.
3F, Haesung Bldg, 504, Teheran-ro, Gangnam-gu, Seoul, 135-725, Korea
Phone: +82-2-2135-5700 Fax: +82-2-2051-5713
RICOH ELECTRONIC DEVICES SHANGHAI CO., LTD.
Room 403, No.2 Building, No.690 Bibo Road, Pu Dong New District, Shanghai 201203,
People's Republic of China
Phone: +86-21-5027-3200 Fax: +86-21-5027-3299
RICOH ELECTRONIC DEVICES CO., LTD.
Taipei office
Room 109, 10F-1, No.51, Hengyang Rd., Taipei City, Taiwan (R.O.C.)
Phone: +886-2-2313-1621/1622 Fax: +886-2-2313-1623