RP400K451C-TR

RP400xxx1C SERIES HIGH EFFICIENCY, SMALL PACKAGES, STEP-UP DC/DC CONVERTERS NO.EA-193-150909 OUTLINE RP400xxx1C Series are high efficiency, step-up DC/DC converter ICs packaged in compact 5pin SOT23 or 6pin DFN(PLP). This converter starts up of low voltage (Typ.1.2V) operation from one to two alkaline or a nickel-metal-hydride (NiMH) or one-cell Lithium-ion (Li+) battery. This IC consists of a reference voltage unit with soft start, a chip enable circuit, an error amplifier, phase compensation circuits, a slope circuit, a PWM control circuit, a start-up circuit, a PWM/VFM mode control circuit, internal switches and a protection circuit. As a protection circuit, RP400xxx1C has a current limit circuit which limits the peak current of the inductor at each clock cycle. A low ripple high efficiency step up DC/DC converter can be composed of RP400xxx1C Series with only an inductor, a diode and capacitors. This converter is based on a fixed frequency current mode PWM control which goes to power save mode (VFM mode) at light load automatically. RP400xxx1C Series has built-in Anti-ringing switch to prevent switching node from ringing, when the converter enters the discontinuous current mode. The output voltage of RP400K001C can be set within 1.8~5.0V (recommended range of output voltage) by external divider resistors. FEATURES ● Low Start-up Voltage guaranteed ··················· 1.2V ● Input Voltage Range ··································· 1.2V~5.5V ● High Efficiency ·········································· 85% (100mA/3.3V，VIN=1.5V，25°C) ● Output current ··········································· 200mA/3.3V(VIN=1.5V) Typ. 100mA/2.0V(VIN=1.2V) ● Internal Switch··········································· NMOS=0.4Ω (VOUT=3.3V, 25°C) ● Built-in Phase Compensation, Soft Start, Peak Current Limit Protection ● PWM Oscillator Frequency ··························· 700kHz ● Output Voltage Range ································· Fixed: 1.8V to 5.0V with 0.1V Stepwise Adjustable: 1.8V~5.0V (RP400K001C only) (Recommended range of output voltage) ● Stable with Ceramic Capacitors ● Small Package ·········································· DFN(PLP)1820-6, SOT23-5 ● Internal EMI suppression (Anti-ringing switch is included) APPLICATIONS ● MP3 players, PDA ● Digital Still Cameras ● LCD Bias Supplies ● Portable blood pressure meter ● Wireless Handset ● GPS 1 RP400xxx1C BLOCK DIAGRAMS 1. Adjustable Output with CE function RP400K001C Lx V IN S ta rtu p C irc u it C o n tro l L o g ic B u ffe r C u rre n t S ense PW M C o n tro l VOUT E rro rA m p CE C h ip E n a b le S le e p fo s c PFM V FB + P ow er S ave M ode O p e ra tio n C o n tro l V re f GND 2. Fixed Output with CE function RP400xxx1C Lx V IN S ta rtu p C irc u it C o n tro l L o g ic B u ffe r C u rre n t Sense PW M C o n tro l E rro rA m p CE C h ip E n a b le S le e p fo s c PFM + P ow er S ave M ode O p e ra tio n C o n tro l V re f GND 2 VOUT - RP400xxx1C SELECTION GUIDE In the RP400 Series, output Voltage, Type of Output Voltage, and package for the ICs can be selected at the user’s request. Product Name RP400Kxx1C-TR RP400Nxx1C-TR-FE Package Quantity per Reel Pb Free Halogen Free DFN (PLP)1820-6 5,000 pcs Yes Yes SOT-23-5 3,000 pcs Yes Yes xx : Designation of output voltage 00: Adjustable Version (1.8V ~ 5.0V) * recommended range of output voltage / DFN(PLP)1820-6 only Fixed version is possible in the range from 1.8V to 5.0V with a step of 0.1V 3 RP400xxx1C PIN CONFIGURATION DFN(PLP)1820-6 SOT-23-5 5 6 1 5 2 4 3 4 1 (Bottom View) 2 3 (Top View) PIN DESCRIPTION RP400K001C: DFN(PLP)1820-6 Pin No Symbol Pin Description 1 VIN Power Supply Pin 2 CE Chip Enable Pin (Active with ”H”) 3 GND 4 Lx Internal NMOS Switch Drain Pin 5 VFB Feedback Input Pin for setting output voltage 6 VOUT Output Pin Ground Pin * Tab is GND level. (They are connected to the reverse side of this IC.) The tab is better to be connected to the GND, but leaving it open is also acceptable. RP400Kxx1C: DFN(PLP)1820-6 Pin No Symbol Pin Description 1 VIN Power Supply Pin 2 CE Chip Enable Pin (Active with ”H”) 3 GND 4 Lx Internal NMOS Switch Drain Pin 5 NC No Connection 6 VOUT Output Pin Ground Pin * Tab is GND level. (They are connected to the reverse side of this IC.) The tab is better to be connected to the GND, but leaving it open is also acceptable. RP400Nxx1C: SOT-23-5 4 Pin No Symbol 1 CE 2 GND 3 VIN 4 VOUT 5 Lx Pin Description Chip Enable Pin (Active with ”H”) Ground Pin Power Supply Pin Output Pin Internal NMOS Switch Drain Pin RP400xxx1C ABSOLUTE MAXIMAM RATINGS Symbol VIN VOUT VFB VLX VCE ILX PD Ta Tstg Items VIN Supply Voltage VOUT Pin Voltage VFB Pin Voltage Pin Input Voltage CE Pin Voltage Lx Pin Output Current Power Dissipation Operating Temp Range Storage Temp Range Ratings -0.3 ~ 6.0 -0.3 ~ 6.0 -0.3 ~ 6.0 -0.3 ~ 6.0 RP400K001A -0.3 ~ 6.0 0.8 SOT-23-5 420 DFN(PLP)1820-6 880 -40 ~ + 85 -55 ~ + 125 (GND=0V) Unit V V V V V A mW °C °C * For Power Dissipation, please refer to PACKAGE INFORMATION to be described. ABSOLUTE MAXIMUM RATINGS Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent damages and may degrade the life time and safety for both device and system using the device in the field. The functional operation at or over these absolute maximum ratings is not assured. RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS) All of electronic equipment should be designed that the mounted semiconductor devices operate within the recommended operating conditions. The semiconductor devices cannot operate normally over the recommended operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. And the semiconductor devices may receive serious damage when they continue to operate over the recommended operating conditions. 5 RP400xxx1C Electrical Characteristics (Ta=25C) Symbol VIN Item Start-up Voltage 2 Vstart3 Start-up Voltage 3 Vhold1 Hold-on Voltage 1 (Once started) IDD2 Istandby VFB VOUT ∆VOUT /∆Ta fosc MAX . Unit 5.5 V 1.2 1.5 V 1.2 1.5 V TYP. Load current = 1mA VCE=1.5V Load current = 1mA CE を VOUT に接続時 Load current = 1mA 0.7 Adjustable Version VIN=3V VOUT=5V VFB=0V Fixed Version VIN=0.5VOUT VOUT= 0.95VOUT Quiescent Current 2 (No switching) Adjustable Version Fixed Version Standby Current VIN=VOUT=5V,VCE=0V Quiescent Current 1 Feedback Voltage (Adjustable Version) Output-Voltage (Fixed Version) Output-Voltage Temperature Coefficient Switching Frequency V 500 800 A VOUT ×100 (*3) A VIN=VOUT=5V VFB=1.0V 160 300 A VIN=VOUT=5V 160 300 A 0.15 3 A 0.600 0.612 V 1.02 V VIN =VOUT=3.3V 0.588 VIN = VCE =1.5V 0.98 -40°C≤Ta≤85°C ppm/ °C ±100 Adjustable Version VIN =VOUT=3.3V 595 700 805 kHz Fixed Version VIN=VOUT=0.95VOUT 595 700 805 kHz ∆fosc /∆Ta Switching Frequency Temperature Coefficient -40°C≤Ta≤85°C ±0.2 kHz /°C RONN NMOS On-Resistance (*1) VOUT=3.3V 0.4 Ω ICEH CE ”H” Input Current VIN=VOUT=VCE=5V ICEL CE ”L” Input Current VIN=VOUT=5V VCE=0V IFBH IXFBL ILX FB ”H” Input Current (Adjustable Version) FB ”L” Input Current (Adjustable Version) Lx Leak Current ILxpeak 0.5 0.5 VIN=VOUT=5V VFB=0V VIN=VOUT=VLX=5V VCE=0V Lx Leak Current limit (*2) Fixed Version A A -0.5 5 VOUT=3.3V Detective at Duty=MaxDuty-5% VOUT= 0.95VOUT Detective at Duty=MaxDuty-5% A A -0.5 VIN=VOUT=VFB=5V Adjustable Version 6 MIN. Input Voltage Vstart2 IDD1 Conditions A 0.4 0.6 A 0.4 0.6 A RP400xxx1C ELECTRICAL CHARACTERISTICS (cont.) (Ta=25C) Symbol Item TYP. MAX. Unit VOUT=3.3V 0.9 V Fixed Version VIN=VOUT=0.95VOUT 0.9 V Adjustable Version VIN=VOUT=3.3V 0.4 V Fixed Version VIN=VOUT= 0.95VOUT 0.4 V Max Duty Adjustable Version VIN=VOUT=3.3V, VFB=0V 80 88 95 % Max Duty Fixed Version VIN=VOUT=0.95VOUT 80 88 95 % Adjustable Version VIN=1.65V VOUT=3.3V VCE=0V to 1.5V VOUT=2.97V 0.08 0.7 3.0 ms 0.08 0.7 3.0 ms CE Input ”H” level Voltage VCEL CE Input “L” level Voltage CE Input “L” level Voltage Soft Start period tstart VIN=VOUT0.5 Soft Start period RONA MIN. Adjustable Version VCEH Maxduty Conditions Anti-ringing switch On Resistance Anti-ringing switch On Resistance Fixed Version (MIN:1.2V) VCE=0V to 1.5V VOUT=VOUT0.9 Adjustable Version VIN=VOUT=3.3V 110 Ω Fixed Version VIN=VOUT=1.05VOUT 110 Ω *1) Guaranteed by design engineering. NMOS On-Resistance according to the VOUT voltage. *2) Lx limit current changes by Duty. *3) The maximum value of Operating Current 1(Fixed Version) is shown on the table below. VOUT (V) 1.8 V 1.9 V 2.0 V 2.1 V 2.2 V 2.3 V 2.4 V 2.5 V 2.6 V 2.7 V 2.8 V 2.9 V 3.0 V 3.1 V 3.2 V 3.3 V 3.4 V MAX (A) 290 310 320 340 360 370 390 400 420 440 450 470 480 500 520 530 550 VOUT (V) 3.5 V 3.6 V 3.7 V 3.8 V 3.9 V 4.0 V 4.1 V 4.2 V 4.3 V 4.4 V 4.5 V 4.6 V 4.7 V 4.8 V 4.9 V 5.0 V MAX (A) 560 580 600 610 630 640 660 680 690 710 720 740 760 770 790 800 7 RP400xxx1C APPLICATION NOTES Adjustable Output Voltage Type (Version:C) Schottky Diode VOUT 1.8V to 5V L 10H(6.8H) V IN CIN 10F Lx RP400K001C CE VOUT COUT 10F “H” active R2 V FB GND R1 Fixed Output Voltage Type (Version:C) Schottky Diode VOUT 1.8V to 5V L 10H(6.8H) V IN CIN 10F Lx RP400xxx1C CE V OUT COUT 10F “H” active GND External components Capacitor Diode Inductor 8 : C2012JB1C106M (TDK) : CRS10I30A (TOSHIBA) : TDK SLF7045T-100M1R3-PF(TDK) RP400xxx1C ● Setting of output voltage Output voltage(1.8V to 5.0V recommended range of voltage) can be set with divider resistors for voltage setting, R1 and R2 as shown in the typical application. Refer to the next formula. (VFB=0.6V) Output Voltage＝ VFB×(R1+R2)/ R1 Recommended value of resistors(R1+R2) is lower than 100kΩ. Make sufficient power supply and ground and reinforce supplying. The large switching current could flow through the connection of power supply, inductor, ground, diode and the connection of VOUT. If the impedance of the connection of power supply and ground is high, the voltage level of power supply of the IC fluctuates with the switching current. We recommend you to use output capacitor and diode with an allowable voltage at least 1.5 times as much as setting output voltage. This is because there may be case where a spike-shaped high voltage is generated by an inductor when built-in transistor is on and off. Use a diode of a Schottky type with high switching speed, low reverse current and also pay attention to its current capacity. Set external components as close as possible to the IC and minimize the connection between the components and the IC. In particular, output capacitor should be connected to VOUT pin with IC ground by the minimum connection, because this IC uses the VOUT voltage as the main power supply, after start-up. Use capacitors with a capacity of 10F or more for VOUT pin. We recommend you to set a ceramic capacitor (10F) between VIN and ground. The divider resistors should be placed as close as possible to the IC ground pin. VFB line is recommended to use short line as well to avoid the influence of noise. Please select the inductor value 10H in the case of VOUT≧2.5V and 6.8H in the case of VOUT