PF2272-1RJ1

PF2270 Series Power Film Resistors • • • • • • • • • Resistances from 0.1 Ohms to 1M Ohms Power Rating to 600 Watts Resistance Tolerances to ±1% TCR of ±100ppm/C TO-227 (TO-238) Housing Moisture Resistant Encapsulation M4x5mm Screws Included Isolated Back Plate Excellent Pulse Handling SPECIFICATIONS Type PF2272 PF2274 PF2276 200 W 300 W 600 W Power Rating (without heatsink) 5W 5W 5W Additional Lead Configurations Y/Z Y/Z Y/Z Power Rating (with heatsink) 0.1 to 1M Ohms Resistance Range ( 0.1 to 1 Ohm only available Terminal Z ) Resistance Values 0.1 to 1M Ohms ( 0.1 to 1 Ohm only available Terminal Z ) 50 to 1K Ohms ( 0.1 to 1 Ohm only available Terminal Z ) E12 ( Plus 2 Ohm and 5 Ohm ) Thermal Resistance 0.35 °C/W Tolerances 0.23 °C/W 0.11 °C/W 5% ( 1% optional ) Temperature Coefficient ±100 ppm/°C Operating Temperature -55°C to 155°C Inductance 14 nH MAX Continuous Voltage √ (P * R) MAX Continuous Current 100A Isolation Voltage 2500VAC (5000VAC on request) Load Life ( 25°C, 90m ON, 30m OFF, 1000hr ) ±1% Humidity ( 40°C, 90-95% RH, DC0.1W, 1000hr ) ±1% Temp. Cycle ( -55°C 30m, 120°C 30m, 20X) ±1% Vibration ( 0.75mm, 100m/s , 10-54Hz, 10X, ±0.25% 2 XYZ ) Insulation Resistance > 1000 MegOhm Flammability UL94 V-0 Substrate AlO Alumina / Cu Flange AlN Weight (grams) 20 30 30 Torque Riedon Inc. © Riedon, Inc. Terminals: 1.0 Nm Max / 0.6 Nm Recommended Mounting: 1.6 Nm Max / 1 Nm Recommended 300 Cypress Avenue Alhambra CA 91801 (626) 284-9901 www.riedon.com sales@riedon.com (626) 284-1704 Revised: 201902_006 PF2270 Series Power Film Resistors SPECIFICATIONS (continued) Dimension mm ( ± mm ) inches ( ± inches ) A 38.0 0.2 1.50 0.008 B 25.0 0.2 0.98 0.008 C* 11.8 0.4 0.465 0.016 D 4.2 0.1 0.165 0.008 E 13.0 0.3 0.512 0.012 F 15.0 0.4 0.591 0.016 G 30.0 0.1 1.181 0.004 H 10.0 0.2 0.394 0.008 *0.25 mm tolerance availble (-T) Mounting Notes The PF2270 Series Power Film Resistors must be attached to a suitable heatsink. Mount resistor using thermal grease to a clean, flat surface. Use a compression washer to provide 150 to 300 pounds ( 665 to 1330N ) of mounting force. Torque mounting screw to 8 in-lbs ( 0.9 N-m ). Torque termination screws to 5 in-lbs (0.6 N-m). Back plate is isolated from both pins. Terminal Configuration & Schematics 4 3 4 3 4 3 1 2 1 2 1 2 STANDARD PF2272 PF2274 PF2276 Y PF2272Y PF2274Y PF2276Y Power Rating Notes The PF2270 Series Power Film Resistors must be attached to a suitable heatsink. The maximum internal resistor temperature is 155°C. To specify an appropriate heatsink use the following formula : RHH = TMAX - (P * RHR) - TA P Where: RθH = Thermal Resistance of Heatsink ( K/W ) RθR = Thermal Resistance of Resistor ( K/W ) TMAX = Maximum Temperature of Resistor TA = Ambient Temperature of Heatsink ( °C ) P = Power Through Resistor ( W ) Riedon Inc. © Riedon, Inc. Z Note: Style Z is not a true 4-terminal measurement. Current can be applied to any pins PF2272Z PF2274Z PF2276Z PF2270 Series Power Derating Curve ％ Rated Power 85 °C 100 Slope 0.35 °C/W 80 60 125 °C 40 155 °C 20 0 -50 0 50 100 150 Base Temperature (°C) 300 Cypress Avenue Alhambra CA 91801 (626) 284-9901 www.riedon.com sales@riedon.com 200 (626) 284-1704 Revised: 201902_006 PF2270 Series Power Film Resistors SPECIFICATIONS (continued) Pulse Durability PF2272 10 OHM 1% 1000 1 00 1 00 . 10 1 0.1 200W 1n 10n 100n 1u 10u 100u 1m 1 0m 100m 1 Pulse Width (seconds) 10 100 Pulse Durability PF2276 100 OHM 1% 1000 Pulse Peak Power (kW) Pulse Peak Power (kW) Pulse Peak Power (kW) 1000 Pulse Durability PF2274 10 OHM 1% 10 1 300W 0.1 1n 10n 100n 1u 10u 100u 1m 1 0m 100m 1 Pulse Width (seconds) 10 100 Tentative continuous pulse power allowance at duty 0.01. Load life test will be necessary in actual equipment because curve may be changed by resistance, repetition, duty, and operating temperature. Dotted line shows estimation. 1 00 10 1 600W 0.1 1n 10n 100n 1u 10u 100u 1m 1 0m 100m 1 Pulse Width (seconds) 10 100 Note: Flying lead terminations are available for enhanced clearance and creepage. Please contact factory for details. Ordering Information Part Description: Part Type - Terminal Style - Resistance - Tolerance PF2274Y 10 Ohms 5% Part Type Terminal Style Resistance Tolerance PF 2272 (*) 0.1 to 100K Ohms 5% PF 2274 Y 50 to 1K Ohms (**) PF 2276 Z Riedon Inc. © Riedon, Inc. (*) For standard terminal style omit letter (**) 1% Tolerance Optional 300 Cypress Avenue Alhambra CA 91801 (626) 284-9901 www.riedon.com sales@riedon.com (626) 284-1704 Revised: 201902_006