2SD1866

Medium Power Transistor (Motor, Relay drive) (60±10V, 2A) 2SD2143 / 2SD1866 Features 1) Built-in zener diode between collector and base. 2) Strong protection against reverse surges due to "L" loads. 3) Built-in resistor between base and emitter. 4) Built-in damper diode. Absolute maximum ratings (Ta=25°C) Parameter Collector-base voltage Collector-emitter voltage Emitter-base voltage 1.0 0.5 Dimensions (Unit : mm) 0.9 0.75 2SD2143 (1) 2.3 5.5 1.5 5.1 (2) 0.9 (3) 2.3 0.65 C0.5 VCBO VCEO VEBO IC 60±10 60±10 6 2 3 1 10 1 ∗2 ∗1 V V V A (DC) A (Pulse) W W (Tc=25°C) W °C °C ROHM : CPT3 EIAJ : SC-63 0.5 1.5 2.5 9.5 2.3 Symbol Limits Unit 0.8Min. Collector current Collector power dissipation 2SD2143 PC 2SD1866 Tj Tstg 2SD1866 6.8 2.5 Junction temperature Storage temperature 150 −55 to +150 ∗1 Single pulse Pw=100ms ∗2 Printed circuit board 1.7mm thick, collector plating 1cm2 or larger. 0.65Max. Packaging specifications and hFE Type Package hFE 1.0 0.9 2SD2143 CPT3 1k to 10k − TL 2500 2SD1866 ATV 1k to 10k − TV2 2500 (1) (2) 2.54 (3) 2.54 0.5 14.5 4.4 1.05 6.5 (1) Base(Gate) (2) Collector(Drain) (3) Emitter(Source) 0.45 Marking Code Basic ordering unit (pieces) Taping specifications ROHM : ATV (1) Emitter (2) Collector (3) Base Inner circuit C B R1 E : Emitter B : Base C : Collector R1 R2 R2 E 3.5kΩ 300Ω Electrical characteristics (Ta=25°C) Parameter Collector-base breakdown voltage Collector-emitter breakdown voltage Collector cutoff current Emitter cutoff current Collector-emitter saturation voltage DC current transfer ratio Symbol BVCBO BVCEO ICBO IEBO VCE(sat) hFE fT Cob Min. 50 50 − − − 1000 − − Typ. − − − − − − 80 25 Max. 70 70 1.0 3 1.5 10000 − − Unit V V µA mA V − MHz pF IC=50µA IC=5mA VCB=40V VEB=5V IC/IB=1A/1mA Conditions ∗ Transition frequency Output capacitance ∗ Measured using pulse current. VCE=2V, IC=1A VCE=5V, IE= −0.1A, f=30MHz VCB=10V, IE=0A, f=1MHz www.rohm.com c ○ 2009 ROHM Co., Ltd. All rights reserved. 1/3 2009.11 - Rev.B 2SD2143 / 2SD1866 Electrical characteristics curves 2.0 1.8 COLLECTOR CURRENT : IC (A) COLLECTOR CURRENT : IC (A) A Data Sheet 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 300 µA A 250µ 25 0µ COLLECTOR CURRENT : Ic (A) 500µA 450µA 400µA Ta=25°C 2.0 1.8 450µA 400µA 1.6 350µA 500µA 30 0µ A Ta=25°C 5 VCE=2V 2 1 0.5 Ta= 100 ˚C 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 IB=2 00µA 20 IB= 0µA 0.2 0.1 0.05 25˚C 0.01 1 2 3 4 5 2 4 6 8 10 0.001 0.5 1 1.5 −25˚C 2 COLLECTOR TO EMITTER VOLTAGE : VCE (V) COLLECTOR TO EMITTER VOLTAGE : VCE (V) BASE TO EMITTER VOLTAGE : VBE (V) Fig.1 Groundede emitter output characteristics ( Ι ) Fig.2 Grounded emitter output characteristics ( ΙΙ ) Fig.3 Grounded emitter propagation characteristics 10000 5000 5000 COLLECTOR SATURATION VOLTAGE : VCE(sat)(V) Ta=25°C VCE=4V 10000 VCE=2V 100 50 20 10 5 2 IC/IB=1000 Ta=25°C DC CURRENT GAIN : hFE 2000 1000 500 200 100 50 20 10 0.001 0.01 0.1 0.2 0.5 1 2 5 10 VCE=2V DC CURRENT GAIN : hFE 2000 1000 500 =1 25°C 200 100 50 20 10 0.001 Ta 5° C 00 °C −2 1 0.5 0.2 500 0.01 0.1 0.2 0.5 1 2 5 10 0.01 0.1 0.2 0.5 1 2 5 10 COLLECTOR CURRENT : IC (A) COLLECTOR CURRENT : IC (A) COLLECTOR CURRENT : IC (A) Fig.4 DC current gain vs. collector current ( Ι ) Fig.5 DC current gain vs. collector current ( ΙΙ ) Fig.6 Collector-emitter saturation voltage vs. collector current COLLECTOR SATURATION VOLTAGE : VCE(sat)(V) IC/IB=1000 COLLECTOR OUTPUT CAPACITANCE : Cob (pF) 100 50 20 10 5 2 1 0.5 0.2 25°C 200 100 COLLECTOR CURRENT : Ic (A) Ta=25°C IE=0A f=1MHz 10 5 2 1 500m 200m 100m 50m 20m 10m 5m Ta=25°C Single Ic max (pulse) DC Pw =1 00 m Pw= 1mS Pw 50 S =1 0m S Ta= −25°C 100°C 20 10 0.01 0.1 0.2 0.5 1 2 5 10 5 0.05 0.1 0.2 0.5 1 2 5 10 20 50 2m Nonrepetitive 1m Pulse 0.1 0.2 0.5 1 2 5 10 20 50 100 200 500 1000 COLLECTOR CURRENT : IC (A) COLLECTOR TO BASE VOLTAGE : VCB (V) COLLECTOR TO EMITTER VOLTAGE : VCE (V) Fig.7 Collector-emitter saturation voltage vs. collector current Fig.8 Collector output capacitance vs. collector-base voltage Fig.9 Safe operating area (A. S. O) 2SD2143 (CPT) www.rohm.com c ○ 2009 ROHM Co., Ltd. All rights reserved. 2/3 2009.11 - Rev.B 2SD2143 / 2SD1866 10 5 Data Sheet COLLECTOR CURRENT : Ic (A) Ic max (pulse) Pw Pw 2 1 500m 200m 100m 50m 20m 10m 5m DC ∗ mS =1 S 0m =1 2m 1m 0.1 0.2 0.5 1 2 Ta=25°C Single Nonrepetitive Pulse ∗ When mounted on 1.7mm thick PCB having collector plating area 1cm2or larger. 5 10 20 COLLECTOR TO EMITTER VOLTAGE : VCE (V) Fig.10 Safe operating area (A. S. O) 2SD1866 (ATV) 0 =1 Pw 0m S 50 100 200 500 1000 www.rohm.com c ○ 2009 ROHM Co., Ltd. All rights reserved. 3/3 2009.11 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A