BA3472FVT-GE2

Datasheet Operational Amplifiers High Speed with High Voltage Operational Amplifiers BA3472xxx BA3472RFVM BA3474xxx BA3474RFV General Description BA3472xxx/BA3472RFVM/BA3474xxx/BA3474RFV are high speed operational amplifiers of dual circuits and quad circuits. An operational range is wide with +3V~+36V (single power supply), and gain bandwidth 4MHz and a high slew rate of in wideband and 10V/μs are good points. Packages SOP8 SOP-J8 SSOP-B8 TSSOP-B8 MSOP8 SOP14 SSOP-B14 TSSOP-B14J Features ◼ Operable with a single power supply ◼ Wide operating supply voltage ◼ Internal phase compensation ◼ High open loop voltage gain ◼ Operable low input voltage around GND level ◼ Wide output voltage range W(Typ) x D(Typ) x H(Max) 5.00mm x 6.20mm x 1.71mm 4.90mm x 6.00mm x 1.65mm 3.00mm x 6.40mm x 1.35mm 3.00mm x 6.40mm x 1.20mm 2.90mm x 4.00mm x 0.90mm 8.70mm x 6.20mm x 1.71mm 5.00mm x 6.40mm x 1.35mm 5.00mm x 6.40mm x 1.20mm Key Specifications ◼ Wide Operating Supply Voltage: Single power supply +3.0V to +36.0V Dual power supply ±1.5V to ±18.0V ◼ Operating Temperature Range: BA3474F -40°C to +75°C BA3472xxx BA3474xxx -40°C to +85°C BA3472RFVM BA3474RFV -40°C to +105°C ◼ Slew Rate: 10V/µs(Typ) ◼ Unity Gain Frequency: 4MHz(Typ) Application ◼ Current sense application ◼ Buffer application amplifier ◼ Active filter ◼ Consumer electronics Simplified Schematic VCC VIN- VOUT VIN+ VEE Figure 1. Simplified schematic (one channel only) ○Product structure：Silicon monolithic integrated circuit www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･14･001 ○This product is not designed protection against radioactive rays. 1/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Pin Configuration BA3472F BA3472FJ BA3472FV BA3472FVT BA3472FVM, BA3472RFVM :SOP8 :SOP-J8 :SSOP-B8 :TSSOP-B8 :MSOP8 OUT1 1 Pin No. OUT1 1 8 VCC 2 -IN1 +IN1 3 VEE 4 7 OUT2 CH1 - + CH2 + - 6 -IN2 -IN1 2 1 CH1 +IN1 3 13 -IN4 2 -IN1 12 +IN4 VCC 4 3 +IN1 11 VEE 5 4 VEE 10 +IN3 OUT1 1 -IN1 2 CH4 + - + - + +IN2 6 -IN2 7 OUT2 8 VCC Pin No. Symbol 1 OUT1 2 -IN1 3 +IN1 CH2 CH3 13 -IN4 +IN1 3 12 +IN4 VCC 4 11 VEE 4 VCC 5 10 +IN3 5 +IN2 9 -IN3 6 -IN2 8 OUT3 7 OUT2 8 OUT3 9 -IN3 10 +IN3 11 VEE 12 +IN4 13 -IN4 14 OUT4 +IN2 -IN2 6 - + CH2 + CH3 OUT2 7 9 -IN3 8 OUT3 :SOP14 :SSOP-B14 :TSSOP-B14J 14 OUT4 CH1 - + - + 5 - + -IN2 6 OUT2 7 BA3474F BA3474FV, BA3474RFV BA3474FVJ 14 OUT4 CH4 OUT1 +IN2 5 +IN2 Symbol Package SOP8 SSOP-B8 SOP-J8 TSSOP-B8 MSOP8 SOP14 SSOP-B14 TSSOP-B14J BA3472F BA3472FV BA3472FJ BA3472FVT BA3472FVM BA3472RFVM BA3474F BA3474FV BA3474RFV BA3474FVJ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 2/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Ordering Information B A 3 4 7 Part Number BA3472xxx BA3472Rxxx BA3474xxx BA3474Rxx x x x x x - Package F : SOP8 SOP14 FV : SSOP-B8 SSOP-B14 FJ : SOP-J8 FVT : TSSOP-B8 FVJ : TSSOP-B14J FVM : MSOP8 xx Packaging and forming specification E2: Embossed tape and reel (SOP8/SOP14/SSOP-B8/SSOP-B14 SOP-J8/TSSOP-B8/TSSOP-B14J) TR: Embossed tape and reel (MSOP8) Line-up Topr -40°C to +75°C Supply Current (Typ) 8.0mA Slew Rate (Typ) 4.0mA -40°C to +85°C 10V/µs 8.0mA -40°C to +105°C Orderable Part Number Package SOP14 Reel of 2500 BA3474F-E2 SOP8 Reel of 2500 BA3472F-E2 SSOP-B8 Reel of 2500 BA3472FV-E2 SOP-J8 Reel of 2500 BA3472FJ-E2 TSSOP-B8 Reel of 2500 BA3472FVT-E2 MSOP8 Reel of 3000 BA3472FVM-TR SSOP-B14 Reel of 2500 BA3474FV-E2 TSSOP-B14J Reel of 2500 BA3474FVJ-E2 4.0mA MSOP8 Reel of 3000 BA3472RFVM-TR 8.0mA SSOP-B14 Reel of 2500 BA3474RFV-E2 www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 3/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Absolute Maximum Ratings (Ta=25℃) Ratings Parameter Symbol Supply Voltage BA3472 VCC-VEE Pd BA3472R BA3474R +36 SOP8 - - - SSOP-B8 690*2*13 - - - 590*3*13 - 590*3*13 - - - 625*4*14 - - 713*5*15 - - - 937*6*16 SOP-J8 675*7*13 - - - TSSOP-B8 625*4*13 - - - SOP14 - 610*8*13 - - - 870 *9*13 - 870*9*13 - - - 1187*10*15 - - - 1689*11*16 - 850*12*13 - - SSOP-B14 TSSOP-B14 Unit V 780*1*13 MSOP8 Power Dissipation BA3474 mW Differential Input Voltage*17 Input Common-mode Voltage Range Input Current*18 Vid +36 V Vicm (VEE - 0.3) to VEE + 36 V II mA Operable with Low Voltage Vopr -10 +3.0V to +36.0V (±1.5V to ±18.0V) Operating Temperature Range Topr Storage Temperature Range Tstg -55 to +150 ℃ Tjmax +150 ℃ Maximum Junction Temperature *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 *13 *14 *15 *16 *17 *18 -40 to +85(SOP14:to +75) -40 to +105 V ℃ To use at temperature above Ta＝25℃ reduce 6.2mW/℃. To use at temperature above Ta＝25℃ reduce 5.5mW/℃ To use at temperature above Ta＝25℃ reduce 4.8mW/℃ To use at temperature above Ta＝25℃ reduce 5.0mW/℃ To use at temperature above Ta＝25℃ reduce 5.7mW/℃ To use at temperature above Ta＝25℃ reduce 7.5mW/℃ To use at temperature above Ta＝25℃ reduce 5.4mW/℃ To use at temperature above Ta＝25℃ reduce 4.9mW/℃ To use at temperature above Ta＝25℃ reduce 7.0mW/℃ To use at temperature above Ta＝25℃ reduce 9.5mW/℃ To use at temperature above Ta＝25℃ reduce 13.5mW/℃ To use at temperature above Ta＝25℃ reduce 6.8mW/℃ Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). Mounted on a FR4 glass epoxy 2 layers PCB 70mm×70mm×1.6mm (occupied copper area：15mm×15mm). Mounted on a FR4 glass epoxy 2 layers PCB 70mm×70mm×1.6mm (occupied copper area：70mm×70mm). Mounted on a FR4 glass epoxy 4 layers PCB 70mm×70mm×1.6mm (occupied copper area：70mm×70mm). The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. An excessive input current will flow when input voltages of less than VEE-0.6V are applied. The input current can be set to less than the rated current by adding a limiting resistor. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 4/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Electrical Characteristics ○BA3472 (Unless otherwise specified Parameter VCC=+15V, VEE=-15V , Ta=25℃) Limits Symbol Unit Min Typ Max - Input Offset Voltage *19 1 10 Vio Vicm=0V, VOUT=0V mV - 1 10 Condition VCC=5V, VEE=0V, Vicm=0V VOUT=VCC/2 Input Offset Current *19 Iio - 6 75 nA Vicm=0V, VOUT=0V Input Bias Current *19 Ib - 100 500 nA Vicm=0V, VOUT=0V Supply Current ICC - 4 5.5 mA RL=∞ 3.7 4 - Maximum Output Voltage(High) VOH 13.7 14 - 13.5 - - VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ VCC=5V, RL=2kΩ - 0.1 0.3 - -14.7 -14.3 - - -13.5 Av 80 100 - dB RL≧2kΩ, VOUT=±10 V Vicm 0 - VCC-2.0 V VCC=5V, VEE=0V VOUT=VCC/2 Common-mode Rejection Ratio CMRR 60 97 - dB Vicm=0V, VOUT=0V Power Supply Rejection Ratio PSRR 60 97 - dB Vicm=0V, VOUT=0V Output Source Current *20 Isource 10 30 - mA Output Sink Current *20 Isink 20 30 - mA Unity Gain Frequency fT - 4 - MHz GBW - 4 - MHz Slew Rate SR - 10 - Channel Separation CS - 120 - Maximum Output Voltage(Low) Large Signal Voltage Gain Input Common-mode Voltage Range Gain Bandwidth *19 *20 VOL V RL=10kΩ RL=2kΩ VCC=5V, VIN+=1V VIN-=0V, VOUT=0V Only 1ch is short circuit VCC=5V, VIN+=0V VIN-=1V, VOUT=5V Only 1ch is short circuit - f=100kHz open loop Av=1, Vin=-10 to +10V V/μs RL=2kΩ dB f=1kHz, input referred Absolute value Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 5/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3472R (Unless otherwise specified VCC=+15V, VEE=-15V, Ta=25℃) Limits Symbol Unit Parameter Min Typ Max - Input Offset Voltage 21 1 10 Vio Vicm=0V, VOUT=0V mV - 1 10 Condition VCC=5V, VEE=0V, Vicm=0V VOUT=VCC/2 Input Offset Current *21 Iio - 6 75 nA Vicm=0V, VOUT=0V Input Bias Current *21 Ib - 100 500 nA Vicm=0V, VOUT=0V ICC - 4 5.5 mA RL=∞ 3.7 4 - 13.7 14 - 13.5 - - - 0.1 0.3 - -14.7 -14.3 - - -13.5 Av 80 100 - dB RL≧2kΩ, VOUT=±10 V Vicm 0 - VCC-2.0 V VCC=5V, VEE=0V VOUT=VCC/2 Common-mode Rejection Ratio CMRR 60 97 - dB Vicm=0V, VOUT=0V Power Supply Rejection Ratio PSRR 60 97 - dB Vicm=0V, VOUT=0V Output Source Current *22 Isource 10 30 - mA Output Sink Current *22 Isink 20 30 - mA Unity Gain Frequency fT - 4 - MHz GBW - 4 - MHz Slew Rate SR - 10 - V/μs Av=1, Vin=-10 to +10V, RL=2kΩ Channel Separation CS - 120 - Supply Current Maximum Output Voltage(High) Maximum Output Voltage(Low) Large Signal Voltage Gain Input Common-mode Voltage Range Gain Bandwidth *21 *22 VOH VOL VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ dB VCC=5V, VIN+=1V VIN-=0V, VOUT=0V Only 1ch is short circuit VCC=5V, VIN+=0V VIN-=1V, VOUT=5V Only 1ch is short circuit f=100kHz open loop f=1kHz, input referred Absolute value Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 6/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx ○BA3474 BA3472RFVM Datasheet BA3474xxx BA3474RFV (Unless otherwise specified VCC=+15V, VEE=-15V, Ta=25℃) Limits Parameter Symbol Unit Min Typ Max - Input Offset Voltage *23 1 10 Vio Vicm=0V, VOUT=0V mV - 1 10 Condition VCC=5V, VEE=0V, Vicm=0V VOUT=VCC/2 Input Offset Current *23 Iio - 6 75 nA Vicm=0V, VOUT=0V Input Bias Current *23 Ib - 100 500 nA Vicm=0V, VOUT=0V ICC - 8 11 mA RL=∞ 3.7 4 - 13.7 14 - 13.5 - - - 0.1 0.3 - -14.7 -14.3 - - -13.5 Av 80 100 - dB RL≧2kΩ, VOUT=±10 V Vicm 0 - VCC-2.0 V VCC=5V, VEE=0V, VOUT=VCC/2 Common-mode Rejection Ratio CMRR 60 97 - dB Vicm=0V, VOUT=0V Power Supply Rejection Ratio PSRR 60 97 - dB Vicm=0V, VOUT=0V Output Source Current*24 Isource 10 30 - mA Output Sink Current *24 Isink 20 30 - mA Unity Gain Frequency fT - 4 - MHz GBW - 4 - MHz Slew Rate SR - 10 - V/μs Av=1, Vin=-10 to +10V, RL=2kΩ Channel Separation CS - 120 - Supply Current Maximum Output Voltage(High) Maximum Output Voltage(Low) Large Signal Voltage Gain Input Common-mode Voltage Range Gain Bandwidth *23 *24 VOH VOL VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ dB VCC=5V, VIN+=1V VIN-=0V, VOUT=0V Only 1ch is short circuit VCC=5V, VIN+=0V VIN-=1V, VOUT=5V Only 1ch is short circuit f=100kHz open loop f=1kHz, input referred Absolute value Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 7/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474R (Unless otherwise specified VCC=+15V, VEE=-15V, Ta=25℃) Limits Parameter Symbol Unit Min Typ Max Input Offset Voltage *25 1 Vicm=0V, VOUT=0V 10 Vio mV - 1 10 Condition VCC=5V, VEE=0V, Vicm=0V VOUT=VCC/2 Input Offset Current *25 Iio - 6 75 nA Vicm=0V, VOUT=0V Input Bias Current *25 Ib - 100 500 nA Vicm=0V, VOUT=0V ICC - 8 11 mA RL=∞ 3.7 4 - 13.7 14 - 13.5 - - - 0.1 0.3 - -14.7 -14.3 - - -13.5 Av 80 100 - dB RL≧2kΩ, VOUT=±10 V Vicm 0 - VCC-2.0 V VCC=5V, VEE=0V, VOUT=VCC/2 Common-mode Rejection Ratio CMRR 60 97 - dB Vicm=0V, VOUT=0V Power Supply Rejection Ratio PSRR 60 97 - dB Vicm=0V, VOUT=0V Output Source Current *26 Isource 10 30 - mA Output Sink Current *26 Isink 20 30 - mA Unity Gain Frequency fT - 4 - MHz GBW - 4 - MHz Slew Rate SR - 10 - V/μs Av=1, Vin=-10 to +10V, RL=2kΩ Channel Separation CS - 120 - Supply Current Maximum Output Voltage(High) Maximum Output Voltage(Low) Large Signal Voltage Gain Input Common-mode Voltage Range Gain Bandwidth *25 *26 VOH VOL VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ VCC=5V, RL=2kΩ V RL=10kΩ RL=2kΩ dB VCC=5V, VIN+=1V VIN-=0V, VOUT=0V Only 1ch is short circuit VCC=5V, VIN+=0V VIN-=1V, VOUT=5V Only 1ch is short circuit f=100kHz open loop f=1kHz, input referred Absolute value Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 8/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Description of Electrical Characteristics Described below are descriptions of the relevant electrical terms Please note that item names, symbols and their meanings may differ from those on another manufacturer’s documents. 1. Absolute Maximum Ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power Supply Voltage (VCC/VEE) Expresses the maximum voltage that can be supplied between the positive and negative supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential Input Voltage (Vid) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input Common-mode Voltage Range (Vicm) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the characteristics or damage to the IC itself. Normal operation is not guaranteed within the common-mode voltage range of the maximum ratings – use within the input common-mode voltage range of the electric characteristics instead. 1.4 Power Dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25℃). For packaged products, Pd is determined by the maximum junction temperature and the thermal resistance. 2. Electrical Characteristics 2.1 Input Offset Voltage (Vio) Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the input voltage difference required for setting the output voltage at 0 V. 2.2 Input Offset Current (Iio) Indicates the difference of input bias current between the non-inverting and inverting terminals. 2.3 Input Bias Current (Ib) Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias current at non-inverting terminal and input bias current at inverting terminal. 2.4 Circuit Current (ICC) Indicates the current of the IC itself that flows under specified conditions and during no-load steady state. 2.5 Maximum Output Voltage(High) / Maximum Output Voltage(Low) (VOH/VOL) Indicates the voltage range that can be output by the IC under specified load condition. It is typically divided into maximum output voltage High and low. Maximum output voltage high indicates the upper limit of output voltage. Maximum output voltage low indicates the lower limit. 2.6 Large Signal Voltage Gain (Av) The amplifying rate (gain) of the output voltage against the voltage difference between non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AV = (output voltage fluctuation) / (input offset fluctuation) 2.7 Input Common-mode Voltage Range (Vicm) Indicates the input voltage range under which the IC operates normally. 2.8 Common-mode Rejection Ratio (CMRR) Indicates the ratio of fluctuation of input offset voltage when in-phase input voltage is changed. It is normally the fluctuation of DC. CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation) 2.9 Power Supply Rejection Ratio (PSRR) Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of DC. PSRR= (Change of power supply voltage)/(Input offset fluctuation) 2.10 Output Source Current/ Output Sink Current (Isource/Isink) The maximum current that can be output under specific output conditions, it is divided into output source current and output sink current. The output source current indicates the current flowing out of the IC, and the output sink current the current flowing into the IC. 2.11 Unity Gain Frequency (fT) Indicates a frequency where the voltage gain of operational amplifier is 1. 2.12 Gain Bandwidth (GBW) Indicates to multiply by the frequency and the gain where the voltage gain decreases 6dB/octave. 2.13 Slew Rate (SR) SR is a parameter that shows movement speed of operational amplifier. It indicates rate of variable output voltage as unit time. 2.14 Channel Separation (CS) Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage of driven channel. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 9/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Typical Performance Curves ○BA3472, BA3472R 1000 6 SUPPLY CURRENT [mA] POWER DISSIPATION [mW] BA3472F 800 BA3472FV 600 BA3472FVT BA3472FVM BA3472RFVM BA3472FJ 400 200 0 0 25 75 85 50 100 105 5 -40℃ 25℃ 4 3 85℃ 105℃ 2 1 0 0 125 5 AMBIENT TEMPERATURE [℃] 10 15 20 25 30 35 40 SUPPLY VOLTAGE [V] Figure 2. Derating Curve Figure 3. Supply Current - Supply Voltage 45 6 30V 36V OUTPUT VOLTAGE[V] SUPPLY CURRENT [mA] 40 5 4 3 5V 3V 2 35 -40℃ 30 25℃ 25 20 85℃ 15 105℃ 10 1 5 0 0 -50 -25 0 25 50 75 100 125 0 10 20 30 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE[V] Figure 4. Supply Current - Ambient Temperature Figure 5. High level Output Voltage - Supply Voltage (RL=10kΩ) 40 (*) The above data is measurement value of typical sample, it is not guaranteed. BA3472：-40℃~＋85℃ BA3472R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 10/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3472, BA3472R 1. 0 45 36V 0. 8 35 OUTPUT VOLTAGE[V] OUTPUT VOLTAGE[V] 40 30 25 30V 20 15 5V 10 3V 0. 6 0. 4 -40℃ 105℃ 85℃ 25℃ 0. 2 5 0. 0 0 -50 -25 0 25 50 75 100 0 125 10 AMBIENT TEMPERATURE [℃] OUTPUT SOURCE CURRENT[mA] OUTPUT VOLTAGE[V] 0. 8 0. 6 0. 4 5V 40 Figure 7. Low level Output Voltage - Supply Voltage (RL=10kΩ) 1. 0 30V 30 SUPPLY VOLTAGE[V] Figure 6. High level Output Voltage - Ambient Temperature (RL=10kΩ) 36V 20 3V 0. 2 0. 0 100.0 -40℃ 10.0 25℃ 85℃ 105℃ 1. 0 0. 1 -50 -25 0 25 50 75 100 125 0 0. 5 1 1. 5 2 2. 5 3 VCC-VOUT[V] AMBIENT TEMPERATURE [℃] Figure 9. Output Source Current - (VCC-VOUT) (VCC/VEE=5V/0V) Figure 8. Low level Output Voltage - Ambient Temperature (RL=10kΩ) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3472：-40℃~＋85℃ BA3472R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 11/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3472, BA3472R INPUT OFFSET VOLTAGE[mV] 5 -40℃ 25℃ 85℃ 105℃ 10.0 1.0 0.1 4 3 -40℃ 2 25℃ 1 0 -1 85℃ 105℃ -2 -3 -4 -5 0 0. 5 1 1. 5 2 2.5 3 3.5 4 4.5 5 -20 VOUT-VEE[V] -15 -10 -5 0 5 10 15 COMMON MODE INPUT VOLTAGE[V] Figure 11. Input Common-mode Voltage Range (VCC/VEE=15V/-15V) Figure 10. Output Sink Current - (VOUT-VEE) (VCC/VEE=5V/0V) 3 INPUT OFFSET VOLTAGE[mV] 3 INPUT OFFSET VOLTAGE[mV] OUTPUT SINK CURRENT[mA] 100.0 2 -40℃ 25℃ 1 0 85℃ -1 105℃ -2 2 30V 1 0 3V 36V 5V -1 -2 -3 -3 0 5 10 15 20 25 30 35 -50 40 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE[℃] SUPPLY VOLTAGE[V] Figure 13. Input Offset Voltage - Ambient Temperature Figure 12. Input Offset Voltage - Supply voltage (*) The above data is measurement value of typical sample, it is not guaranteed. BA3472：-40℃~＋85℃ BA3472R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 12/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3472, BA3472R 100 INPUT BIAS CURRENT[nA] INPUT BIAS CURRENT[nA] 100 80 -40℃ 25℃ 85℃ 60 40 105℃ 20 80 5V 40 3V 36V 20 0 0 0 5 10 15 20 25 30 35 -50 40 LARGE SIGNAL VOLTAGE GAIN[dB] 150 140 130 120 25℃ 85℃ 110 100 105℃ 90 80 70 60 50 0 5 10 15 20 25 30 0 25 50 75 100 125 Figure 15. Input Bias Current - Ambient Temperature Figure 14. Input Bias Current - Supply voltage -40℃ -25 AMBIENT TEMPERATURE[℃] SUPPLY VOLTAGE[V] LARGE SIGNAL VOLTAGE GAIN[dB] 30V 60 35 40 150 140 130 3V 120 5V 30V 110 100 36V 90 80 70 60 50 -50 SUPPLY VOLTAGE[V] -25 0 25 50 75 100 125 AMBIENT TEMPERATURE[℃] Figure 17. Large Signal Voltage Gain - Ambient Temperature Figure 16. Large Signal Voltage Gain - Supply Voltage (*) The above data is measurement value of typical sample, it is not guaranteed. BA3472：-40℃~＋85℃ BA3472R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 13/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3472, BA3472R 140 150 130 140 120 130 120 36V 110 CMRR[dB] CMRR[dB] 110 100 30V 100 90 25℃ 85℃ 80 105℃ -40℃ 70 60 60 50 50 3V 5V 80 70 40 40 0 5 10 15 20 25 30 35 -50 40 -25 0 25 50 75 100 SUPPLY VOLTAGE[V] AMBIENT TEMPERATURE[℃] Figure 18. Common Mode Rejection Ratio - Supply Voltage Figure 19. Common Mode Rejection Ratio - Ambient Temperature 14 125 14 -40℃ 12 85℃ SLEW RATE(RISE)[V/μs] 12 SLEW RATE(RISE)[V/μs] 90 25℃ 10 8 105℃ 6 4 2 0 36V 30V 10 8 15V 6 5V 3V 4 2 0 0 5 10 15 20 25 30 35 40 -50 -25 0 25 50 75 100 125 AMBIENT TEMPERATURE[℃] SUPPLY VOLTAGE[V] Figure 21. Slew Rate L-H - Ambient Temperature (RL=10kΩ) Figure 20. Slew Rate L-H - Supply Voltage (RL=10kΩ) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3472：-40℃~＋85℃ BA3472R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 14/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3472, BA3472R 50 12 0 -30 GAIN 30 -60 20 -90 10 -120 0 PHASE[deg] VOLTAGE GAIN[dB] 40 -150 INPUT/OUTPUT VOLTAGE[V] 10 PHASE 8 6 OUTPUT 4 INPUT 2 0 -2 -4 -6 -8 -10 -10 1 10 100 1000 -180 10000 -12 0 1 2 3 4 5 6 7 8 TIME[μs] FREQUENCY[kHz] Figure 23. Input / Output Voltage - Time (VCC/VEE=15V/-15V, Av=0dB, RL=2kΩ, CL=100pF, Ta=25℃) Figure 22. Voltage Gain・Phase - Frequency (VCC=7.5V/-7.5V, Av=40dB, RL=2kΩ, CL=100pF, Ta=25℃) INPUT/OUTPUT VOLTAGE[mV] 100 80 INPUT 60 40 OUTPUT 20 0 -20 -40 -60 -80 -100 0.0 0.5 1.0 1.5 2.0 2.5 TIME[μs] Figure 24. Input / Output Voltage - Time (VCC/VEE=15V/-15V, Av=0dB, RL=2kΩ, CL=100pF, Ta=25℃) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3472：-40℃~＋85℃ BA3472R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 15/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474, BA3474R 12 BA3474F 800 SUPPLY CURRENT [mA] POWER DISSIPATION [mW] 1000 BA3474FV BA3474RFV BA3474FVJ 600 400 200 0 0 25 75 85 50 10 -40℃ 25℃ 8 6 85℃ 105℃ 4 2 0 100105 125 0 AMBIENT TEMPERATURE [℃ ] 5 10 15 20 25 30 35 40 SUPPLY VOLTAGE [V] Figure 25. Derating Curve Figure 26. Supply Current - Supply Voltage 12 45 30V OUTPUT VOLTAGE[V] SUPPLY CURRENT [mA] 40 10 36V 8 6 3V 4 5V 2 35 -40℃ 30 25℃ 25 20 85℃ 15 105℃ 10 5 0 0 -50 -25 0 25 50 75 100 125 0 AMBIENT TEMPERATURE [ ℃] 10 20 30 40 SUPPLY VOLTAGE[V] Figure 27. Supply Current - Ambient Temperature Figure 28. High level Output Voltage - Supply Voltage (RL=10kΩ) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3474F：-40℃~＋75℃ BA3474：-40℃~＋85℃ BA3474R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 16/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474, BA3474R 45 1. 0 OUTPUT VOLTAGE[V] OUTPUT VOLTAGE[V] 36V 40 35 30 25 30V 20 15 5V 10 3V 0. 8 0. 6 0. 4 -40℃ 105℃ 85℃ 25℃ 0. 2 5 0 0. 0 -50 -25 0 25 50 75 100 0 125 AMBIENT TEMPERATURE [℃] 10 OUTPUT SOURCE CURRENT[mA] OUTPUT VOLTAGE[V] 0. 8 0. 6 0. 4 5V 3V 0. 2 0. 0 -50 -25 0 25 50 75 40 Figure 30. Low level Output Voltage - Supply Voltage (RL=10kΩ) 1. 0 30V 30 SUPPLY VOLTAGE[V] Figure 29. High level Output Voltage - Ambient Temperature (RL=10kΩ) 36V 20 100 100. 0 -40℃ 10.0 25℃ 105℃ 1. 0 0. 1 125 0 AMBIENT TEMPERATURE [℃] 0. 5 1 1. 5 2 2. 5 3 VCC-VOUT[V] Figure 32. Output Source Current - (VCC-VOUT) (VCC/VEE=5V/0V) Figure 31. Low level Output Voltage - Ambient Temperature (RL=10kΩ) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3474F：-40℃~＋75℃ BA3474：-40℃~＋85℃ BA3474R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 17/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474, BA3474R 5 INPUT OFFSET VOLTAGE[mV] -40℃ 25℃ 85℃ 105℃ 10.0 1. 0 4 3 -40℃ 2 25℃ 1 0 105℃ 85℃ -1 -2 -3 -4 -5 0. 1 -20 0 0. 5 1 1. 5 2 2. 5 3 3. 5 4 4. 5 5 VOUT-VEE[V] -15 -10 -5 0 5 10 15 COMMON MODE INPUT VOLTAGE[V] Figure 34. Input Common-mode Voltage Range (VCC/VEE=15V/-15V) Figure 33. Output Sink Current - (VOUT-VEE) (VCC/VEE=5V/0V) 3 INPUT OFFSET VOLTAGE[mV] 3 INPUT OFFSET VOLTAGE[mV] OUTPUT SINK CURRENT[mA] 100. 0 2 25℃ -40℃ 1 85℃ 0 105℃ -1 -2 -3 2 36V 30V 1 5V 3V 0 -1 -2 -3 0 5 10 15 20 25 30 35 40 -50 -25 SUPPLY VOLTAGE[V] 0 25 50 75 100 125 AMBIENT TEMPERATURE[℃] Figure 35. Input Offset Voltage - Supply voltage Figure 36. Input Offset Voltage - Ambient Temperature (*) The above data is measurement value of typical sample, it is not guaranteed. BA3474F：-40℃~＋75℃ BA3474：-40℃~＋85℃ BA3474R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 18/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474, BA3474R 100 INPUT BIAS CURRENT[nA] INPUT BIAS CURRENT[nA] 100 80 -40℃ 25℃ 85℃ 60 40 105℃ 20 0 80 5V 60 40 36V 3V 20 0 0 5 10 15 20 25 30 35 40 -50 -25 SUPPLY VOLTAGE[V] LARGE SIGNAL VOLTAGE GAIN[dB] 140 130 120 110 25℃ 85℃ 100 90 105℃ 80 70 60 50 0 5 10 15 20 25 30 25 50 75 100 125 Figure 38. Input Bias Current - Ambient Temperature 150 -40℃ 0 AMBIENT TEMPERATURE[℃] Figure 37. Input Bias Current - Supply voltage LARGE SIGNAL VOLTAGE GAIN[dB] 30V 35 150 140 130 120 5V 110 30V 100 90 36V 3V 80 70 60 50 -50 40 -25 0 25 50 75 100 125 AMBIENT TEMPERATURE[℃] SUPPLY VOLTAGE[V] Figure 40. Large Signal Voltage Gain - Ambient Temperature Figure 39. Large Signal Voltage Gain - Supply Voltage (*) The above data is measurement value of typical sample, it is not guaranteed. BA3474F：-40℃~＋75℃ BA3474：-40℃~＋85℃ BA3474R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 19/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474, BA3474R 140 150 130 140 120 130 120 110 CMRR[dB] CMRR[dB] 110 100 90 105℃ 80 36V 25℃ 85℃ 3V 5V 90 80 -40℃ 70 70 60 60 50 50 40 40 0 5 10 15 20 25 30 35 -50 40 SUPPLY VOLTAGE[V] -25 0 25 50 75 100 125 AMBIENT TEMPERATURE[℃] Figure 42. Common Mode Rejection Ratio - Ambient Temperature Figure 41. Common Mode Rejection Ratio - Supply Voltage 14 14 12 -40℃ SLEW RATE(RISE)[V/μs] 12 SLEW RATE(RISE)[V/μs] 30V 100 85℃ 25℃ 10 8 6 105℃ 4 36V 8 15V 6 2 0 0 5 10 15 20 25 30 35 5V 4 2 0 30V 10 3V -50 40 SUPPLY VOLTAGE[V] -25 0 25 50 75 100 125 AMBIENT TEMPERATURE[℃] Figure 44. Slew Rate L-H - Ambient Temperature (RL=10kΩ) Figure 43. Slew Rate L-H - Supply Voltage (RL=10kΩ) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3474F：-40℃~＋75℃ BA3474：-40℃~＋85℃ BA3474R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 20/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV ○BA3474, BA3474R 50 12 0 -3 0 GAIN 30 -6 0 20 -9 0 10 -1 20 0 PHASE[deg] VOLTAGE GAIN[dB] 40 INPUT/OUTPUT VOLTAGE[V] 10 PHASE 8 OUTPUT 6 INPUT 4 2 0 -2 -4 -6 -8 -1 50 -10 -10 -1 80 1 10 100 1000 -12 0 10000 FREQUENCY[kHz] 1 2 3 4 5 6 7 8 TIME[μs] Figure 46. Input / Output Voltage - Time (VCC/VEE=15V/-15V, Av=0dB, RL=2kΩ, CL=100pF, Ta=25℃) Figure 45. Voltage Gain・Phase - Frequency (VCC=7.5V/-7.5V, Av=40dB, RL=2kΩ, CL=100pF, Ta=25℃) INPUT/OUTPUT VOLTAGE[mV] 100 80 60 INPUT 40 OUTPUT 20 0 -20 -40 -60 -80 -100 0.0 0.5 1.0 1.5 2.0 2.5 TIME[μs] Figure 47. Input / Output Voltage - Time (VCC/VEE=15V/-15V, Av=0dB, RL=2kΩ, CL=100pF, Ta=25℃) (*) The above data is measurement value of typical sample, it is not guaranteed. BA3474F：-40℃~＋75℃ BA3474：-40℃~＋85℃ BA3474R：-40℃~＋105℃ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 21/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Application Information NULL method condition for Test Circuit 1 VCC, VEE, EK, Vicm Unit : V Parameter VF S1 S2 S3 VCC VEE EK Input Offset Voltage VF1 ON ON OFF 15 -15 0 0 1 Input Offset Current VF2 OFF OFF OFF 15 -15 0 0 2 VF3 OFF ON VF4 ON OFF OFF 15 -15 0 0 3 ON ON ON 15 -15 +10 0 15 -15 -10 0 ON ON OFF 15 -15 0 -15 15 -15 0 13 ON ON OFF 2 -2 0 0 18 -18 0 0 Input Bias Current VF5 Large Signal Voltage Gain VF6 Common-mode Rejection Ratio (Input Common-mode Voltage Range) VF7 VF8 VF9 Power Supply Rejection Ratio VF10 Vicm Calculation 4 5 6 －Calculation－ 1. Input Offset Voltage (Vio) | VF1 | [V] Vio = 1 + Rf / Rs 0.1μF 2. Input Offset Current (Iio) Rf=50kΩ | VF2－VF1 | [A] Iio = Ri ×(1 + Rf / Rs) SW1 | VF4－VF3 | EK +15V 2×Ri× (1 + Rf / Rs) Ri=10kΩ Ri=10kΩ 4. Large Signal Voltage Gain (Av) Av = 20×Log VCC Rs=50Ω [A] Ib = 0.1μF 500kΩ 3. Input Bias Current (Ib) ΔEK×(1+Rf /Rs) 500kΩ DUT Vicm [dB] |VF5-VF6| NULL SW3 Rs=50Ω 1000pF V RL SW2 50kΩ 5. Common-mode Rejection Ratio (CMRR) CMRR = 20×Log ΔVicm×(1+Rf /Rs) VF VEE -15V [dB] Figure 48. Test circuit 1 (one channel only) |VF8-VF7| 6. Power Supply Rejection Ratio (PSRR) PSRR = 20×Log ΔVcc×(1+Rf /Rs) [dB] |VF10-VF9| Switch Condition for Test Circuit 2 SW No. Supply Current SW 1 SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 SW 8 SW 9 SW 10 SW 11 SW 12 SW 13 SW 14 OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF Maximum Output Voltage(High) OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF Maximum Output Voltage(Low) OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF Output Source Current OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON Output Sink Current OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON Slew Rate OFF OFF OFF ON OFF OFF OFF ON ON ON OFF OFF OFF OFF Gain Bandwidth Product OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFF OFF Equivalent Input Noise Voltage ON OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF OFF www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 22/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Voltage SW4 VH R2 SW5 VCC A VL － SW1 SW2 RS R1 Input Voltage Waveform ＋ SW3 SW6 SW7 SW8 time Voltage 電圧 SW9 SW10 SW11 SW12 SW13 90% VH SW14 ΔV VEE C A ～ VIN- VIN+ ～ RL CL V ～ V VL 10% VOUT Δt Output Voltage Waveform 出力電圧波形 Figure 49. Test circuit 2 (one channel only) time 時間 Figure 50. Slew rate input output wave VCC VCC R1//R2 R1//R2 OTHER CH VEE VEE R1 VIN R2 R1 V VOUT2 R2 V VOUT1 =0.5[Vrms] CS＝20 × log 100 × VOUT1 VOUT2 Figure 51. Test circuit 3 (Channel Separation) www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 23/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Power Dissipation Power dissipation(total loss) indicates the power that can be consumed by IC at Ta=25℃(normal temperature). IC is heated when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip (maximum junction temperature) and thermal resistance of package (heat dissipation capability). The maximum junction temperature is typically equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called thermal resistance, represented by the symbol θja℃/W.The temperature of IC inside the package can be estimated by this thermal resistance. Figure 52. (a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient temperature Ta, maximam junction temperature Tjmax, and power dissipation Pd can be calculated by the equation below: θja = (Tjmax-Ta) / Pd ℃/W Derating curve in Figure 52. (b) indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient iis determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Figure 52. (c) to (f) shows a derating curve for an example of BA3472, BA3474, BA3472R, BA3474R. Power Dissipation of電 LSI LSIの 消 費 力 [W] θja=(Tjmax-Ta)/Pd Pd (max) ℃/W θja2 < θja1 P2 Ambient Temperature 周囲温度 Ta [℃] θ' ja2 P1 θ ja2 Tj ' (max) θ' ja1 Chip Surfaceチップ Temperature 表面温度 Tj [℃] Power Dissipation [W] 消費電力 Pd P [W] 0 25 50 Tj (max) θ ja1 75 100 125 150 Ambient temperature 周 囲 温 度 Ta [℃ ] (b) Derating Curve (a) Thermal Resistance 1000 BA3474F(*35) BA3472F(*27) 800 POWER DISSIPATION Pd [mW] BA3472FV(*28) 600 許 容 損 失 Pd [mW] POWER Pd [mW] 損 失 Pd [mW] 許 容DISSIPATION 1000 BA3472FVT(*30) BA3472FVM(*31) BA3472FJ(*29) 400 200 0 800 BA3474FV(*36) BA3474FVJ(*37) 600 400 200 0 0 25 50 75 100 125 0 Ambient周Temperature: 囲 温 度 Ta [℃Ta ] [℃] 25 50 (c)BA3472 125 1800 1600 BA3472RFVM(*32) 800 BA3472RFVM(*34) BA3472RFVM(*31) 600 400 200 BA3474RFV(*38) 1400 許 容 損 失 Pd [mW] POWER DISSIPATION Pd [mW] 許 容 損 失 Pd [mW] 100 (d)BA3474 1000 POWER DISSIPATION Pd [mW] 75 Ambient周Temperature: 囲 温 度 Ta [℃ Ta ] [℃] BA3474RFV(*39) 1200 BA3474RFV(*36) 1000 800 600 400 200 0 0 0 25 50 75 100 0 125 25 50 75 100 125 周囲 温 度 Ta [℃ ] Ta [℃] Ambient Temperature: 周Temperature: 囲 温 度 Ta [℃ ]Ta [℃] Ambient (e)BA3472R (f)BA3474R (*27) (*28) (*29) (*30) (*31) (*32) (*33) (*34) (*35) (*36) (*37) (*38) (*39) Unit 6.2 5.5 5.4 5.0 4.8 7.5 5.7 5.0 4.9 7.0 6.8 13.5 9.5 mW/℃ When using the unit above Ta=25°C, subtract the value above per Celsius degree. (*27)(*28)(*29)(*30)(*31)(*35)(*36)(*37) Mounted on a FR4 glass epoxy 1 layers PCB 70mm×70mm×1.6mm (copper foil area less than 3%). (*34) Mounted on a FR4 glass epoxy 2 layers PCB 70mm×70mm×1.6mm (occupied copper area：15mm×15mm). (*33) (*39) Mounted on a FR4 glass epoxy 2 layers PCB 70mm×70mm×1.6mm (occupied copper area：70mm×70mm). (*32) (*38) Mounted on a FR4 glass epoxy 4 layers PCB 70mm×70mm×1.6mm (occupied copper area：70mm×70mm). Figure 52. Thermal Resistance and Derating Curve www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 24/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the PD stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the PD rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 25/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Operational Notes – continued 11. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Resistor Transistor (NPN) Pin A Pin B C E Pin A N P+ P N N P+ N Pin B B Parasitic Elements N P+ N P N P+ B N C E Parasitic Elements P Substrate P Substrate GND GND Parasitic Elements GND Parasitic Elements GND N Region close-by Figure 53. Example of monolithic IC structure 12. Unused Circuits When there are unused circuits it is recommended that they are connected as in Figure 54, setting the non-inverting input terminal to a potential within input common-mode voltage range (Vicm). Keep VCC this potential in Vicm 13. Input Terminal Voltage Applying GND + 36V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 14. Power Supply (Single / Dual) The op-amp operates when the specified voltage supplied is between VCC and VEE. Therefore, the single supply op-amp can be used as dual supply op-amp as well. + VEE Figure 54. The Example of Application Circuit for Unused Op-amp 15. IC Handling Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezo resistance effects. 16. Output Capacitor Discharge of the external output capacitor to VCC is possible via internal parasitic elements when VCC is shorted to VEE, causing damage to the internal circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation due to output capacitive load does not occur, such as in voltage comparators, use an output capacitor with a capacitance less than 0.1µF. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 26/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Physical Dimension, Tape and Reel Information Package Name SOP8 (Max 5.35 (include.BURR)) (UNIT : mm) PKG : SOP8 Drawing No. : EX112-5001-1 www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 27/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name SOP14 (Max 9.05 (include.BURR)) (UNIT : mm) PKG : SOP14 Drawing No. : EX113-5001 www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 28/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 SSOP-B8 29/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 SSOP-B14 30/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 TSSOP-B8 31/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 TSSOP-B14J 32/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 SOP-J8 33/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 MSOP8 34/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Marking Diagrams SOP8(TOP VIEW) SOP14(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK SSOP-B14(TOP VIEW) Part Number Marking SSOP-B8(TOP VIEW) Part Number Marking LOT Number LOT Number 1PIN MARK TSSOP-B8(TOP VIEW) Part Number Marking 1PIN MARK TSSOP-B14J (TOP VIEW) Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK MSOP8(TOP VIEW) Product Name FV BA3472R BA3474 BA3474R Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK Package Type F BA3472 SOP-J8(TOP VIEW) Marking SOP8 SSOP-B8 FVM MSOP8 FJ SOP-J8 3472 FVT TSSOP-B8 FVM MSOP8 3472R F SOP14 BA3474F FV SSOP-B14 FVJ TSSOP-B14J FV SSOP-B14 www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 3474 3474R 35/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Land pattern data all dimensions in mm Land length Land width ≧ℓ 2 b2 PKG Land pitch e Land space MIE SOP8 SOP14 1.27 4.60 1.10 0.76 SOP-J8 1.27 3.90 1.35 0.76 SSOP-B8 SSOP-B14 0.65 4.60 1.20 0.35 MSOP8 0.65 2.62 0.99 0.35 TSSOP-B8 0.65 4.60 1.20 0.35 TSSOP-B14J 0.65 4.60 1.20 0.35 b2 e MIE ℓ2 Revision History Date Revision 27.Feb.2012 001 26.Oct.2012 002 23.Apr.2014 003 11.Jul.2014 11.Dec.2020 004 005 Changes New Release Addition BA3472FJ, BA3472FVT, BA3474FVJ Addition Land pattern data Addition Input Current of Absolute Maximum Ratings(Page 2) Addition of item of Operational Notes Correction of simplified schematic.(Page 1) P.36-2, 36-3, Updated packages and part numbers. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 36/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM Datasheet BA3474xxx BA3474RFV Ordering Information B A Part Number BA3474 3 4 7 4 F Package F: SOP14K - Z Production site Z: Added E 2 Packaging and forming specification E2: Embossed tape and reel Marking Diagram SOP14K (TOP VIEW) Part Number Marking BA3474F LOT Number Pin 1 Mark www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 36-2/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 BA3472xxx BA3472RFVM BA3474xxx BA3474RFV Datasheet Physical Dimension and Packing Information Package Name www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 SOP14K 36-3/36 TSZ02201-0RAR0G200100-1-2 11.Dec.2020 Rev.005 Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001