BA3830F_11

1/4 Structure : Product : Type : Function : Silicon Monolithic Integrated Circuit Band-pass filter for spectrum analyzer for car audio systems BA3830F 1. Built-in band pass filter for spectrum analyzer 2. Designed for 5V microcomputer power voltage 3. SOP18 package requiring few external parts Absolute Maximum Ratings (Ta=25℃) Symbol Rating Parameter Power Supply voltage Vcc 9 Power dissipation Pd 450※ Operating temperature Topr -25～+75 Storage temperature Tstg -55～+125 ※This value decreases 4.5 mW/℃ for Ta=25℃ or more. Operating Voltage Range（Ta＝25℃） Parameter Symbol Power supply voltage Vcc Unit V mW ℃ ℃ Min. 4.5 Typ. - Max. 8.0 Unit V Application example Note that ROHM cannot provide adequate confirmation of patents. The product described in this specification is designed to be used with ordinary electronic equipment or devices (such as audio-visual equipment, office-automation equipment, communications devices, electrical appliances, and electronic toys). Should you intend to use this product with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. REV. B 2/4 Electrical Characteristics （Unless specified particularly, Ta＝25℃，VCC＝5V，RL＝10MΩ, Rφ1＝270kΩ, Rφ2＝270kΩ） Limit Symbol Parameter Unit Conditions Min. Typ. Max. Quiescent current Reference output level（LEVEL） IQ Vol VolMax Vor － -3 3.2 -3 3.8 － 49 117 257 0.78 2.55 7.8 150 － 1.0 3.8 0 4.2 0 4.8 30 63 150 330 1 3.3 10 215 1.4 1.4 5.2 3 － 3 － 90 77 183 403 1.22 4.03 12.2 280 1.8 － mA dB V dB V mV Hz Hz Hz kHz kHz kHz μA V V VIN=-30dBV、VO＝1.5V（0dB） When f=center frequencies is input VIN=-14dBV, When f＝center frequencies is input VIN=-30dBV、VO＝1.5V（0dB） f=1kHz VIN=－14dBV、f＝1kHz With no signal VIN=-30dBV VIN=-30dBV VIN=-30dBV VIN=-30dBV VIN=-30dBV VIN=-30dBV Vth＝5V Max. output level（LEVEL） Reference output level（REC LEVEL） Max. output level（REC LEVEL） VorMax Output offset voltage Voff Center frequency 1 fo1 Center frequency 2 fo2 Center frequency 3 fo3 Center frequency 4 fo4 Center frequency 5 fo5 Center frequency 6 fo6 Input current when Reset IIN pin is HIGH Threshold level when Reset Vth pin is ON Threshold level when Reset Vth pin is OFF ※Q is set to 4.5. ◎ Not designed for radiation resistance. Outline Dimension BA3830F LOT No. SOP18 （Unit：mm） REV. B 3/4 Block Diagram Terminal Number/ Terminal Name Terminal Number 1 2 3 4 5 6 Terminal Name Ro2 Ro1 LINENF LINEIN RECNF RECIN Terminal Number 7 8 9 10 11 12 Terminal Name RESETC BASIC GND1 VCC RECLEVLE fo6 Terminal Number 13 14 15 16 17 18 Terminal Name fo5 fo4 fo3 fo2 fo1 RESET REV. B 4/4 Application example (1) Numbers and data in entries are representative design values and are not guaranteed values of the items. (2) Although we are confident in recommending the sample application circuits, carefully check their characteristics further when using them. When modifying externally attached component constants before use, determine them so that they have sufficient margins by taking into account variations in externally attached components and the Rohm LSI, not only for static characteristics but also including transient characteristics. (3) Absolute maximum ratings If applied voltage, operating temperature range, or other absolute maximum ratings are exceeded, the LSI may be damaged. Do not apply voltages or temperatures that exceed the absolute maximum ratings. If you think of a case in which absolute maximum ratings are exceeded, enforce fuses or other physical safety measures and investigate how not to apply the conditions under which absolute maximum ratings are exceeded to the LSI. (4) GND potential Make the GND pin voltage such that it is the lowest voltage even when operating below it. Actually confirm that the voltage of each pin does not become a lower voltage than the GND pin, including transient phenomena. (5) Thermal design Perform thermal design in which there are adequate margins by taking into account the allowable power dissipation in actual states of use. (6) Shorts between pins and misinstallation When mounting the LSI on a board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is misinstalled and the power is turned on, the LSI may be damaged. It also may be damaged if it is shorted by a foreign substance coming between pins of the LSI or between a pin and a power supply or a pin and a GND. (7) Operation in strong magnetic fields Adequately evaluate use in a strong magnetic field, since there is a possibility of malfunction. REV. B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A