BA6800AF

Audio ICs Fluorescent display tube level meter driver, 16-point 2 channel, VU scale, bar display BA6800AF The BA6800AF is a two-channel, 16-point fluorescent display tube driver for VU-scale bar-level meters. It uses a dynamic-drive system and is provided with both AC and DC inputs. The AC input mode has a peak hold circuit. The IC features a power-on mute, and the output block can directly drive fluorescent display tubes, so few external components are required. FApplications Level meters for all types of AV equipment FFeatures 1) Uses dynamic-drive system to display two 16-point channels. 28-pin SOP package. 2) AC and DC inputs provided. Switching function allows two-mode display. 3) Upper 12 points have peak hold function in AC mode (two seconds). 4) Power-on mute function. 5) Dynamic-drive system reduces the power dissipation of the fluorescent display tube power supply. 6) Square root compression amplifier built in. 804 Audio ICs FBlock diagram BA6800AF FAbsolute maximum ratings (Ta = 25_C) FElectrical characteristics (unless otherwise noted, Ta = 25_C) 805 Audio ICs FElectrical characteristics (unless otherwise noted, Ta = 25_C) BA6800AF 806 Audio ICs FMeasurement circuit BA6800AF FApplication example 807 Audio ICs FCircuit operation (1) Input block The AC input pins are pins 1 and 3, and the DC input pins are pins 5 and 6. Pin 7 is used to switch between the AC and DC inputs. When the input to pin 7 is “H”, AC input is selected (pins 1 and 3). Therefore, by using pin 7 to switch between the AC and DC modes, the IC can do two jobs. For example, pins 1 and 3 can be used for audio signal input, and pins 5 and 6 can be used as the input for the signal meter output from a tuner (DC). The AC input impedance of pins 1 and 3 is a low 250Ω (Typ.), so connect potentiometers (VR1 and VR2) in series with the inputs to adjust the sensitivity and ch1 and ch2 balance. (2) Peak hold circuit The BA6800AF have peak hold circuits that temporarily holds peak signal levels in AC input mode. The peak hold function can be used with the upper 12 points (5 to 16). The peak hold time depends on the oscillator frequency. It is 2 sec. (Typ.) for an oscillator frequency of 2kHz. DC mode does not have a peak hold function. (3) Grid output The pin 9 and 10 grid outputs are open-collector NPN transistors. The logic is active low (the fluorescent tube lights when the output is “L”), so connect two PNP transistors Q1 and Q2 as shown in the application example circuit to drive the fluorescent tubes (see Fig. 3). BA6800AF (4) Segment output block Pins 11 to 26 are the segment outputs. The output circuits are open-collector PNP transistors. When grid 1 is “L”, the ch1 level is output (pin 1 or 5 input level), and when grid 2 is “L”, the ch2 level is output (pin 3 or 6 input level). Refer to Fig. 4. (5) Grid and segment output timing chart. The grid and segment output timing for an oscillator frequency of 2kHz is shown in Fig. 5. (6) Attack and release times The response characteristic for AC input signals is set by resistor R1 and capacitor C3 for ch1 and resistor R2 and capacitor C4 for ch2 (pins 2 and 4). When R1 = 47kΩ and C3 = 22µF, the attack time is about 4ms, and the release time is about 1sec. (same for ch2). Attack time : Time for the voltage on pins 2 and 4 to rise from 1V to 2.5V when the input goes from no input to 2.6Vrms, then back to no input. Release time : Time for the voltage on pins 2 and 4 to fall from 2.5V to 1V when the input goes from 2.6Vrms to no input. (7) Oscillator frequency The resistor R26 and capacitor C5 connected to pin 28 determine the oscillator frequency. The oscillator frequency (fosc) and grid output period (T) are related as follows : T (ms) = 16 / fosc (kHz) 808 Audio ICs FTiming chart BA6800AF FAttached components (refer to “Circuit operation”) C1 and C2 : input coupling capacitors. VR1 and VR2 : AC sensitivity adjustment and balance adjustment (3kΩ recommended). C3, R1, C4 and R2 : set the response characteristics with respect to the AC input signal. In the example given, the attack time is about 4mS and the release time is about 1sec. R3 : Pullup resistor for the input switching terminal (pin 7). R6 and R7 : resistor for the grid leak current path (IGleak). R6 (R7) < 0.6V. Set so that IGleak R4 and R5 : base bias resistors for Q1 and Q2. Conditions for base bias current (IB) flow are VCC = 5V and VF = 0.6V : = 7.3 R6 0.6 the base current is given by the following formula. IB (mA) IB > 5*0.6 R4 (kΩ) R6 (kΩ) Fluorescent tube grid current * 0.6 R4 < 5*0.6 FOperation notes (1) Adjust the potentiometers VR1 and VR2 (connected to pins 1 and 3) to adjust the 0dB input level and the dispersion of ch1 and ch2. (2) The temperature characteristic for the lighting limit for the 16th LED is shown in Fig. 6. (3) The external resistor R26 connected to the oscillator (pin 28) should be in the range of 20kΩ and 100kΩ. If it is outside this range, oscillation may stop due to the influence of temperature (see Fig. 7). hFE Set resistors R4 and R6 (R5 and R7) so that Q1 and Q2 : grid output inverting transistors. Use transistors for which VCEO > VCC ) VEE. R8 to R25 : Resistors that reverse bias the segments and grid when the fluorescent tube is not lit. The application example given is for general cases. Select the resistors to suit the characteristics of the fluorescent tube used. C5 and R26 : set the oscillator frequency. Capacitor C5 should be a component with good temperature characteristics. 809 Audio ICs FElectrical characteristics curves BA6800AF FExternal dimensions (Units: mm) 810