BA7654F-E2

High-performance Video Signal Switchers Single-circuit Video Switchers BA7654F,BA7653AF,BA7653AFV,BA7652AF No.11066EAT04 ●Description The BA7654F, BA7653A F/FV or BA7652AF is a video signal (display signal) switch containing one 2-input or 3-input circuit. Each of the input pin formats is “sync-tip clamp input” that matches the synchronous tips of video signals (display signals) to the same potential. The inputs have an high input impedance configuration, in which they can utilize a small clamp capacitor (0.01 µF (FZ) ceramic capacitor is recommended). ●Features 1) Low value clamp capacitance can be used (Min. 3000 pF Recommended 0.01µF (FZ) ceramic capacitor) 2) Low voltage operation is possible (Operating range 4.0～7.0V) 3) Superimposed can be applied since switching speed of SW is fast and there is little switching noise (Typ. 70ns) 4) Low power consumption (Typ. 25mW when Vcc=5V) 5) Large dynamic range (Typ. 3.1VP-P when Vcc=5V) 6) Good frequency characteristics (Typ. 10 MHz 0 dB) 7) Low interchannel crosstalk (Typ. –70 dB) 8) Voltage can be applied to the CTL pin without a VCC voltage. 9) Built-in mute function (BA7652AF) ●Applications VCR, TV, and other applications that use display signals. ●Product lineup Part No. Input type Mute BA7654F 2 in 1 Circuit － BA7653AF, BA7653AFV 3 in 1 Circuit － BA7652AF 3 in 1 Circuit ○ Supply voltage(V) 4.0 ～ 7.0 ●Absolute maximum ratings(Ta=25℃) Parameter Symbol Supply voltage Ratings BA7654F BA7653AF VCC BA7653AFV BA7652AF 9 Unit V Pd 500*1 500*1 350*2 500*1 mW Operating temperature Topr -25～+75 -30～+80 -30～+80 -30～+80 ℃ Storage temperature Tstg Power dissipation -55～+125 ℃ *1 Reduce by 5.0mW/℃ over 25℃, when mounted on a 50mm×50mm PCB board.(BA7654F, BA7653AF, BA7652AF) *2 Reduce by 3.5mW/℃ over 25℃, when mounted on a 50mm×50mm PCB board.(BA7653AFV) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/9 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Operating range(Ta=25℃) Parameter Symbol Ratings Unit VCC 4.0 ～ 7.0 V Supply voltage Note: This IC is not designed to be radiation-resistant. ●Electrical characteristics(Unless otherwise noted, Parameter Symbol Ta=25℃, Vcc=5.0V) Limits Min. Typ. Max. Unit Conditions Circuit current ICC 2.7 5.0 8.2 mA Maximum output level Vom 2.6 3.1 － VP-P f=1kHz, THD=1.0% Voltage gain GV -0.5 0 +0.5 dB f=1MHz, VIN=1.0VP-P Inter channel crosstalk Cta － -70 － dB f=4.43MHz, VIN=1.0VP-P Frequency characteristics Cf -3.0 0 +1.0 dB f=10MHz/1MHz, VIN=1.0VP-P VTH L － － 1.0 V VTH =(Vcc-0.75)×0.44 VTH H 2.5 － － CTL switching voltage ●Guaranteed design parameters (Unless otherwise noted, Ta=25℃, Vcc=5.0V) Limits Parameter Symbol Unit Min. Typ. Max. Conditions Differential phase DG － 0 0.5 % VIN=1.0VP-P, standard staircase signal Differential gain DP － 0.5 1.0 deg VIN=1.0VP-P, standard staircase signal www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/9 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Block diagram IN1 1 8 GND IN1 1 8 GND CTL 2 7 OUT CTLa 2 7 OUT IN2 3 6 VCC IN2 3 6 VCC 5 IN3 Logic GND Logic 4 5 Open. CTLb Fig.1 BA7654F 4 Fig.2 BA7653AF, BA7653AFV Fig.3 BA7652AF ●Control Pin Settings BA7654F BA7653AF, BA7653AFV BA7652AF CTL OUT CTLa CTLb OUT CTLa CTLb OUT L IN1 L L IN1 L L IN1 H IN2 H L IN2 H L IN2 L H IN3 L H IN3 H H IN3 H H MUTE www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/9 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Pin descriptions 1/2 (BA7654F) BA7654F DC voltage (Vcc=5V) Input/output impedance 1.65V 10MΩ or more CTL － － GND 0V － 5 N.C. open open 6 Vcc 0.5V － 7 OUT 0.95V 26Ω Pin No. Pin name 1 IN1 (3) (IN2) 2 4 (8) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/9 Equivalent circuit IN1 (IN2) CTL － 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Pin descriptions 2/2 (BA7653AF, BA7653AFV, BA7652AF) BA7653AF, BA7653AFV, BA7652AF Pin No. Pin name DC voltage (Vcc=5V) 1 (3) (5) IN1 (IN2) (IN3) 1.65V 10MΩ or more 2 CTLa － － 4 CTLb － － 6 Vcc 5.0V － 7 OUT 0.95V 26Ω 8 GND 0V － www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Input/output impedance 5/9 Equivalent circuit IN1 (IN2) (IN3) 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Application circuit 1/2 (BA7654F) Vcc BA7654F 0.01µF C.Video IN 1 IN 1 Vcc 6 47µF 0.1µF 0.01µF C.Video IN Logic 3 IN 2 5 Open 2 CTL 4 GND OUT 7 GND 8 C.Video OUT Fig.4 (When superimpossion is used) 0.01µF 47µF 0.1µF DC1.7V or more Fig.5 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/9 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Application circuit 2/2 (BA7653AF, BA7653AFV, BA7652AF) BA7653AF, BA7653AFV, BA7652AF Fig.6 (When superimpossion is used) BA7653AF, BA7653AFV, BA7652AF DC1.7V or more DC1.7V or more Fig.7 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/9 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Notes for use 1. Numbers and data in entries are representative design values and are not guaranteed values of the items. 2. Although ROHM is confident that the example application circuit reflects the best possible recommendations, be sure to verify circuit characteristics for your particular application. Modification of constants for other externally connected circuits may cause variations in both static and transient characteristics for external components as well as this Rohm IC. Allow for sufficient margins when determining circuit constants. 3. Absolute maximum ratings Use of the IC in excess of absolute maximum ratings, such as the applied voltage or operating temperature range (Topr), may result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage is suffered. A physical safety measure, such as a fuse, should be implemented when using the IC at times where the absolute maximum ratings may be exceeded. 4. GND potential Ensure a minimum GND pin potential in all operating conditions. Make sure that no pins are at a voltage below the GND at any time, regardless of whether it is a transient signal or not. 5. Thermal design Perform thermal design, in which there are adequate margins, by taking into account the permissible dissipation (Pd) in actual states of use. 6. Short circuit between terminals and erroneous mounting Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other components on the circuits, can damage the IC. 7. Operation in strong electromagnetic field Using the ICs in a strong electromagnetic field can cause operation malfunction. 8. For clamp operation stability Set the output impedance of the stage before input pin no more than 1 kΩ. 9. An input clamp capacitor will cause delay in operation at power on. Therefore, it is recommended to use a clamp capacitor no larger than 0.1 µF (0.01µF (FZ) ceramic capacitor is recommended). 10. TheBA7653AF, BA7653AFV and BA7652AF are 3-input, 1-output switch. If it is used as a 2-input, 1-output switch, by leaving one input Open and unused, the Open input pin will oscillate. However, this does not affect other pins and is not particularly a problem for operation. If necessary, connect the input pin to GND via a capacitor or connect the input pin directly to VCC to stop oscillation. 11. CTL pin is in indeterminate status when left Open. Set it at “H” or “L” level. 12. For superimposed, a 1.7v DC voltage should be applied directly to an input pin. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/9 2011.04 - Rev.A Technical Note BA7654F,BA7653AF,BA7653AFV,BA7652AF ●Ordering part number B A 7 Part No. 6 5 3 A F Part No. 7654 7653A 7652A V Package F : SOP8 FV:SSOP-B8 - E 2 Packaging and forming specification E2: Embossed tape and reel SOP8 5.0±0.2 (MAX 5.35 include BURR) 6 +6° 4° −4° 5 6.2±0.3 4.4±0.2 0.3MIN 7 1 2 3 0.9±0.15 8 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 4 0.595 1.5±0.1 +0.1 0.17 -0.05 S S 0.11 0.1 1.27 1pin 0.42±0.1 Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B8 3.0±0.2 (MAX 3.35 include BURR) 8 7 6 5 Tape Embossed carrier tape Quantity 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 0.3MIN 6.4 ± 0.3 4.4 ± 0.2 Direction of feed 2 3 4 0.1 1.15±0.1 1 0.15±0.1 S (0.52) 0.65 0.1 S +0.06 0.22 −0.04 0.08 1pin M Reel (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/9 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.04 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A